Directorate Of Ports And Inland Water Transport Tender

Shifting and setting up piling equipments required for piling work at each piling location, including all labour, labour cess, materials, fuel, tools & equipments etc.required to complete in all respect as per direction of Engineer-in-Charge ( No payment will be made for 1st pile )

Boring piles for 400mm dia to the required depth through all types of soil strata including hard rock if any up to the founding level and stacking the bored soil at convenient place and transport to dispose the same at low lying area outside the working area with cleaning & washing the bore including cost of bentonite solution, labour, labour cess, tools, equipments, required to complete in all respect as per direction of the Engineer’-in-charge. Note:- 01. If the boring tool encounters rock at an elevation higher than the termination level of the pile indicated in the drawing then the boring shall be continued one metre into the rock from where the boring tool encounters rock first. 02. In case the soil stratum at the founding level is loose the Engineer or his representative may direct the contractor to carryout additional length of boring and payment for such additional work shall also be made under this item. 03. The sample of bored materials at regular interval shall be collect and produce for the verification of the Engineer or his representative at no extra cost. In the event of any dispute about the type of strata bored, the samples so collected shall be referred to an authorised laboratory / agency indentified by the Engineer and the decision of such authorised laboratory / agency is final and binding on both the parties. However the cost of such testing shall be borne by the contractor.

Supplying, fabricating and providing Mild steel cylindrical liner of 4mm thick with shoe to the required depth including providing additional stiffener plates of 4mm thick & 500 mm hight including cutting, bending, welding, transporting, alignment, placing in position and driving to required depth with all labour, labour cess, materials, tools, equipments etc. complete in all respect as per direction of Engineer-in-Charge. Note:- The stiffener shall be measured under this item. In case the soil strata found to be not good in the founding level, extra depth of liner may be provided as per site condition and measurement will be made to this effect.

Providing and placing designed mix cast-in-situ RCC M-30 using 20 mm down graded black hard granite crusher broken chips for piles using tremmie method up to cut off level underneath the bentonite slurry including all sampling, testing and records with watering and laying as per IS codes 456 and 516. including cost, conveyance, royality, labour, Labour Cess, T&P and all other taxes etc. required to complete the work in all respect as per specification and direction of the Engineer in charge. Note: Supply, fabrication of steel reinforcement shall be measured and paid under relevant item (Rate shall include the cost of providing additional concrete above the cut-off level)

Cutting and dressing pile heads to required line and level and /or as directed and stacking the debris at convenient place and transport the same to any low lying area outside the working area and all associated cleaning of projecting reinforcements including all labour, labour cess, materials, tools, equipments etc., complete in all respect as per direction of the Engineer’-in-charge.

Providing dry rubble rock toe with blasted and quarried granite boulders of sizes 30cm and above with all leads and lifts including dumping with packing interstices properly and surface packing to proper line and level including cost, conveyance, royality, labour, Labour Cess, T&P and all other taxes etc. required to complete the work in all respect as per specification and direction of the Engineer in charge.( No deduction to be made towords voids in finished section.)

Quarrying,collecting, conveying, supplying and spreading good quality laterite moorum and consolidation with HRR including watering with cost, conveyancy, royality and all taxes , labour, labour cess etc. complete as per direction of Engineer-in-Charge.

Providing and placing designed mix cast-in-situ RCC M-30 with 20 mm. down graded black hard granite crushed broken stone chips of approved quality and from approved quarry including hoisting, lowering and laying concrete and compacting by using vibrators, watering and curing for 4 weeks and finishing the exposed surface smooth providing grooves or beads where necessary with all sampling, testing and records in all floors including cost, conveyance, royalities and taxes of all materials cost of all labour, labour cess, T&P etc. required for the work to complete in all respect as per direction of Engineer in Charge. Note: Supply, fabrication of steel reinforcement shall be measured and paid under relevant item

Supplying, fabricating and placing of HYSD (FE-415) /(FE-500) grade steel for pile cage including cutting , bending, binding & welding and laying in position with cost, conveyance, taxes of HYSD steel and binding wires 18 to 20 gauge with all labour,labour cess, T&P, cage lowering, equipments etc., complete in all respect as directed by the Engineer in charge. (Brand of Steel - SAIL ) Measurement of reinforcement will be made on lengthwise including hooks, if any, separately for different diameter as actually used in work, excluding overlaps, from the length so measured, the weight of reinforcement shall be calcuted in tonnes by multiplying the coefficient per unit length of bar as per code of the respective size of bars used on the basis of wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods for binding & placing shall not be measured as the cost of these items has already been included in the analysis of rates for reinforcement as per rule in force . (PILES)

Supplying, fabricating and placing of HYSD (FE-415) /(FE-500) grade steel for pile cage including cutting , bending, binding & welding and laying in position with cost, conveyance, taxes of HYSD steel and binding wires 18 to 20 gauge with all labour,labour cess, T&P, cage lowering, equipments etc., complete in all respect as directed by the Engineer in charge. (Brand of Steel - SAIL ) Measurement of reinforcement will be made on lengthwise including hooks, if any, separately for different diameter as actually used in work, excluding overlaps, from the length so measured, the weight of reinforcement shall be calcuted in tonnes by multiplying the coefficient per unit length of bar as per code of the respective size of bars used on the basis of wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods for binding & placing shall not be measured as the cost of these items has already been included in the analysis of rates for reinforcement as per rule in force .

Rigid smooth centering and shuttering for R.C.C. works including false works and dismentalling then after casting including cost, conveyance, royality, labour, Labour Cess, T&P and all other taxes etc. required to complete the work in all respect as per specification and direction of the Engineer in charge. RCC Beam, Columns Girders & Brassmers etc)