Assam Rifles Tender

Providing and laying 3mm thick APP modified prefabricated five layer, 3 mm thick water proofing membrane, black finished reinforced with glass fibre matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufactured of density at 25°C, 0.87 - 0.89 kg/litre and viscocity 70 - 160 cps. Over the primer coat the layer of membrane shall be laid using butane torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 350/300 N/5 cm Tear strength in longitudinal and transverse direction as 60/80N Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147.The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with ISI marked white solid plastic seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required.

Providing and fixing White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps with C.I. brackets, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.

Providing and fixing 40 mm dia Flexible P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Providing and fixing to existing door frames 30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a uPVC hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x30 mm and 2 mm (± 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S. 'U' cleats complete as per manufacturer's specification and direction of Engineer-in-charge.

Providing and fixing 15 mm nominal bore 45 cm length uplasticised PVC connection pipe with brass unions.

Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS:8931 and as per direction of Engineer - in - Charge.

Providing and fixing 15mm nominal bore CP brass angle value.

Providing and fixing of 15mm nominal bore CP brass stop cock(Concealed).

Providing and fixing of CP brass shower rose with 15 or 20 mm inlet,100mm die.

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping sand papering and preparing the surface smooth including necessary repairs to scratches etc complete in walls and ceiling.

Distempering One or more coats on old work with 1st quality acrylic distemper (ready made) having VOC content less than 50 gm per ltr. of approved manufacturer and of required shade and colour complete. as per manufacturer's specification.

Finishing walls with Acrylic Smooth exterior paint of required shade on Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface.

Painting One or more coats on old work with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade.

Providing and laying in position cement concrete of specified grade excluding the cost of cantering and shuttering, 1:3:6, 20 mm graded aggregate in plinth protection.

Renewing glass panes, with putty and nail wherever necessary including racking out the old putty, 4mm thick float glass panes.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fiffings and the base support for tank 100 ltr capacity.

Providing and fixing 15mm nominal bore GI union in existing GI pipe including cutting and threading the pipe and making long screws including excavation refilling the earth or cutting of wall and making good the same complete wherever required.

Providing and fixing 20mm nominal bore GI union in existing GI pipe including cutting and threading the pipe and making long screws including excavation refilling the earth or cutting of wall and making good the same complete wherever required.

Providing and fixing 25 mm nominal bore Gun metal gate value with CI wheel of approved quality (Screwed end).

Providing and fixing 40 mm nominal bore Gun metal gate value with CI wheel of approved quality (Screwed end).

Providing and fixing ball value(brass) of approved quality high or low pressure with plastic bloats complete 20 mm nominal dia.

Dismantling of old plaster or skirting raking out joints and clearing the surface for plaster including disposal of rubbish to the dumping ground within 50 mtr lead.

20 mm cement plaster of mix 1:4 (1 cement: 4 fine sand).

Neat cement punning. upto plinth level