Pradhan Mantri Gram Sadak Yojana Tender

Construction of granular sub-base with locally available graded material, spreading in uniform layers with motor grader on prepared surface, watering to OMC and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification/ direction of EE.

Water Bound Macadam Sub-base/Base: Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening/binding materials to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 2 as per Technical Specification Clause 405.

Grading-2 (A) By manual means

Grading-3 (A) By manual means

Bituminous Work

Prime Coat: (i) Low porosity: Providing and applying primer coat with bitumen emultion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 Kg/sqm using mechanical means as per technical Clause 502.

Tack Coat: (III) Providing and applying tack coat with bitumen emultion (RS-1) Using emultion distributor at the rate of 0.25-0.30 Kg/sqm on the prepared granular surface treasted with primer & cleaned with hydraulic broom as per technical specification clause 503.

20mm thick Open-Graded Premix Carpet using Bituminous Emulsion as per Technical Specification clause 508.2 Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508.

Seal coat: Providing and laying seal coat sealing the voids in a bitumenious surface laid to the specified levels, using cold emulsion grade and cross fall using Type A, Type B and Type C as per Technical Specification Clause 510. A. By Manual Means Case - I : Type C

Construction of sub-grade and earthen shoulders Construction of sub-grade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, etc. and compacting to meet requirement of Table 300.2 with lead upto 1000m…. (For earthen shoulders)

Construction of retaining walls/breast walls in cement mortar 1:5 as per drawing and technical specifications Clause 1604

Earthwork in excavation for structures (Rate as per item No.11.1 of Chapter 11)

Stone masonry (Dry) (Rate as per item No. 12.4 (III) (iv) of Chapter 12)

Filter material behind retaining wall / breast wall as per Specification 1204.3.8 in a width of 600 m Rate as per item No. 12.11 of Chapter 12

Providing and fixing 'Logo' of PMGSY: Providing and fixing of typical PMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1

Citizen Informatory Board of PMGSY (As per SOR of 2015-16)

Providing & fixing Logo of PMGSY ((As per SOR of 2015-16) )

Logo Board at every 2 Km (As per SOR of 2015-16)

Painting lines, Dashes, Arrows, etc. on Road in Two Coats on New Work Painting lines, dashes, arrows, etc. on roads in two coats on new work with ready mixed road marking paint conforming to IS:164 on bituminous/concrete surface, including cleaning the surface of all dirt, dust and other foreign matter, demarcation at site and traffic control as per drawing and Technical Specification Clause 1702

Providing and erecting direction and place identification retro- reflectorised sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3, fixed over aluminium sheeting, 2 mm thick with area exceeding 0.9 sqm supported on RCC Posts 100 mm x 100 mm firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per approved drawing and Technical Specification Clause 1701

Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3, fixed over aluminium sheeting, 1.5 mm thick supported on GI pipe 50 mm dia firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and Technical Specification Clause 1701

(ii) 600 mm equilateral triangle

(iii) 600 mm circular

Maintenance

1st Year

2nd Year

3rd Year

4th Year

5th Year