Pradhan Mantri Gram Sadak Yojana Tender

(2) Grading-2 (A) By manual means

(3) Grading-3 (A) By manual Means

Prime Coat

(i) Low porosity: Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 Kg/sqm using mechanical means as per Technical specification Clause 502

Tack Coat

(III) Providing and applying tack coat with bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 - 0.30 Kg/sqm on the prepared granular surface treated with primer and claened with hydraulic broom as per Technical specification Clause 503

20mm thick Open-Graded Premix Carpet

Providing, laying and rolling of open graded premix carpet of 20mm thickness composed of 13.2 mm to 5.6 mm aggregate either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base including mixing in a suitable plant, laying and rolling with a three wheel 80-100 Kn static roller capacity finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical specification Clause 508. A. By Manual Means (I) Bitumen Emulsion(Cold Mix)

Seal Coat

Providing and laying seal coat sealing the voids in a bituminous surface laid to specified levels, grade and cross fall using Type A, Type B and Type C as per Technical specification Clause 510. A. By Manual Means Case -I Type-A (I). Bitumen Emulsion (Cold Mix)

Construction of Sub Grade and Earthen Shoulders.

Const. of Subgrade and Earthen Shoulders with approved materials obtained from Borrow pits with all lifts and leads. Etc. and compacting to meet requirement of Table 300.2 with lead upto 1000 m……(For earthen shoulders)

(i) Surface Drains in Soil

Construction of unlined surface drains of average cross-sectional area 0.40 sqm in soil to specified lines, grades, levels and dimensions. Excavated material to be used in embankment with a lift upto 3m and lead of 50 m (average lead 25 m) as per Technical Specification Clause 307.

Providing and fixing Logo of PMGSY Providing and fixing of typical PMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6mm thick, top and middle plate duly welded with MS Flatiron 25mmx5mm size on back on edges. The lower plate will be welded with MS amgle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame opf middle plate will be welded to two nos. 75mm x 75mm of 12 SWG Sheet rtubes posts duly embedded in cement concrete M-15 Grade blocks of 450mm x 450mm x 600mm, 600mm below groun d level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All MS will be stove enameled on both sides. Letteering and printing arrows, border etc. will be pain ted with misxed synthetic enamel paint of superior quality in required shade and colour. All se3ctions of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing clause 1701 and Annexure 1700.1.

(i) Repainting of Citizen, Informatory & Maintenance Sign Board of PMGSY (RATE TO BE QUOTED IN LUMPSUM RATE) CIB =1No IB =2No Logo =7Nos

(ii)PMGSY Maintenance Board. Providing and fixing of PMGSY Maintenance Board as per Drawng and Specification… etc.

Traffic Signs Providing and fixing of retro-reflectorised cautionary,mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3, fixed over aluminium sheeting,1.5mm thick supported on GI pipe 50mm dia firmly fixed to the ground, etc as perdrawings and Technical Specification Clause 1701

ii) 600 mm equilateral triangle

iii)600 mm circular

iv)800 mm x 600 mm rectangular

v)600 mm x 450 mm rectangular

Maintenance of Culverts Maintenance of Hume pipe Culvert by way of Clearing, Cleaning, Erosion repair, repairs to cracks, parapet wall and protection work as per drawing and technical specification Clause 1908.

Repairing of Guard walls of HP Culverts.

Painting

Painting two coats including primer coat after filling the surface with synthetic enamel paint in all shades on new, plastered / concrete surfaces as per drawing and Technical Specification Clause 1701 i).Guard walls of HP

Five Years Maintenance

Ist Year

IInd Year

IIIrd Year

IVth Year

Vth Year