North Eastern Electric Power Corporation Limited Tender

b) Above 40 mm nominal above

Providing and fixing Chlorinated Polyvinyl Chrolide (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the wall etc. ii) 20 mm nominal outer diameter Pipes

Providing and fixing Chlorinated Polyvinly Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (viii) 75 mm nominal inner diameter Pipes

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete with sand cost iron S&S as per IS:1729 b) 75 mm dia.

Half brick masonry with common burnt clay (non modular) 1st class brick in superstructure above plinth levelup to first floor level. a) Cement mortar 1:3 ( 1 cement: 3 coarse sand)

Cutting holes of required size in brick masonry wall for fixing of exhaust fan including providing and fixing 300 mm dia. PVC pipe conforming BIS­12818 and making good the same etc. complete as per direction of Engineer-in-Charge.

12 mm cement plaster of mix: (a) 1:4 (1 cement: 4 coarse sand)

Providing polished VITRIFIED wall tiles of approved quality,size,shape and thickness not less than 8 mm on walls and skirting over cement mortar bed 10 mm thick in prop.1:3 (1 cement: 3 coarse sand) including cutting where necessary finished with flush pointing with adhesive or white cement slurry mixed with papproved pigment to match shade of tiles complete at all levels as specified and directed. b) Premium range

Providing vitrified Antiskid Tiles of approved quality size, shape not less than 8 mm on floor, skirting over a cement mortar bed 15 mm thick of 1:3 (1 cement: 3 coarse sand) complete at all level as specified and directed. b) Premium range

Providing and fixing aluminium work for doors, window, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections of approved make conforming to IS:733 and IS:1285, fixing withdash fasteners of required diameter and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.(Glazing, and panelling to be paid for separately): a) For fixed portion i) Anodised aluminium (anodised transparent or dyed to required shade according to IS:1868, Minimum anodic coating of grade AC 15)

B) For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gate required (Fittings shall be paid for separately) i) Anodised aluminium (anodised transparent or dyed to required shade according to IS:1868, Minimum anodic coating of grade AC 15)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber/ neoprane gasket etc. complete as per the architectural drawings and the direction of engineer-in-charge: b. With float glass panes of 4.0 mm thickness (weight not less than 10 kg/sqrn)

Extra for openable side/ top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardware for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per Architectural drawings, as per the approved shop drawing, as specified and as directed by the Engineer-in-Charge.

Providing and fixing anodised aluminium (anodised transparent or dyed to required sahade according to IS:1868 with minimum anodic coating of grade AC 15) od approved design/ pattern, with approved standard section and fixed to the existing window/ frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cuttiing the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-Charge. (Only weight of grill to be measured for payment).

Providing and fixing Fibre Glass Reinforced plastic (FRP) Door Frames of cross-section 90x45 mm having single rebate of 32x15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block in all the three legs. The frame with suitable wooden block in all the three legs. The frame shall be covered with fibre glass from all sides. M.S. stay shall be provided at the bottom to steady the frame.

Providing and fixing to existing door frames. a) 30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fir-retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and sites, with wooden frame and suitable blocks of seasoned wood inside at equired places for fixing of fittings, cast monolithically with 5 mm thick FRP laminated for panels conforming to IS:14856, including fixing to frames.

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc.complete: a. 125 mm

Providing and fixing aluminium tower bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade with necessary screws etc.complete: b.250x10 mm

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc.complete :250 x 16mm

Providing and fixin white vitreous china battery based infrared sensor operated urinal of approx. size 610x390x370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.

Providing and fixing vitreous china bidet completes cutting and making good the walls and floors wherever required.(Bidet mixture to be paid separately) a) White

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. A) 15mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm C.P.brass pillar taps, 32 mm C.P.brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: d) White Vitreous China Flat basin size 550x400 mm with a pair of 15mm C.P. brass pillar tap

Supplying fitting and fixing of exhaust fan double bearing self lubricating type singlevphase 50Hz 250V AC operated complete with supporting frame , fan blades, nuts and bolts and pther petty acessosories as required.

wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: Old work (one or more coats)

Finishing walls with Acrylic Smooth exterior paint of required shade, including scaffolding: a) Old work (Two or more coat applied @ 1.67 ltr/10 sqm) on existing cement paint surfaces

Supplying, fitting and fixing MAC vertical blinds complete as specified and directed by the department at all levels.

a) Normal

Labour charges for removing and replacing of Furniture

Supplying, Fitting and fixing in position 4.5mm thick Vinyl Flooring .

Supplying, Fitting and fixing in position 4.5mm thick Badminton court mat pre marked of approved brand and manufacture with adhesive on cleansed and dried surface including cutting and smoothening the edge and disposal of waste materials complete as directed by Engineer-in-charge.

Providing fitting and fixing in position 19mm thick water proof Block Board of approved brand to the partition wall on one face of the timber frame of local white pine wood of 75mm X 50mm spaced at not more than 0.60m apart, fixed with Fevicol,glue etc including necessary nails,wood screws, bolts etc (wood work will be paid separately) complete as directed by the Department.

Providing and fixing mirror of superior glass(of approved quality) and required shape and size. Regular shape size 600mm X 750mm X 600mm X 600mm

Providing and fixing 600x450 mm brvelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard bord ground fixed to wooden cleats with C.P. bras screws and washers complete.