Border Security Force Tender

Supplying & fixing of prfabricated single door front opeanle SMC junction box inside dimension size (250mmx200mm)x105mm comprising of locking arrangement and incoming/outgoing cable duct ,PVC connector,din plate , C-clamp etc i/c connection as required as per direction of engineer incharge(Make-Sintex/Hencel/spelsberg or equivalent ISI approved make)

Supplying and fixing of single pole 5 A to 32 A rating, 240/415 V, 10 kA, "C"curve, miniature circuit breaker suitable for inductive load of in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Provding & fixing of 150Watt LED flood light flood light fitting suitable for operating volatge 140-270 volt on single phase AC,50Hz supply with following technical specification :- a) Input volatge - 90-300 volt AC ,50Hz frequency .b)LED lamp efficiency -100 to 130Lm/Watt .c)uniformity ratio or minimum and average illumination is 0.3 .d) usage hours 12-14 per day .e) power factor - 0.95 . f) life expectancy -50,000Hours. g)Rated wattage - 150Watt . h)lumen flux - 19500lm . i)colour temperature -3000K .j) LED make-Nichai/Cree/Osram/Phllips/Seoul/or other ISI marked as per diretion of engineer incharge.k)Driver- designed for constant current and operating voltage from 90-300 volts .L)working humidity -10% to 90 RH .m)working temp -5 deg to 50 deg.n)ingress protection - IP66 or aboe ,colour rendering index - -Ra80 ,Total harmonic distortion 10%,surge protection -6KV,Average lighting beam/Beam angle - 120degree ,luminarie housing - pressure dia casting aluminum with toughened glass cover ,pole entry -suitable for mounting 30-56mm dia meter pipe bracket on existing pole with locking arrangement ,bolt etc as required ,system component -PCB is made of glass proxy FR4 & metal core PCB for LED ,control circuit -compatible to LED lamp wattage ,Thermal management of LED - good thermal management is provide & LED mounted to heat sink conductive aluminum with suitable large area surface by means of fins to dissipate the heat to ambient air ,electric wire -50Cm ,03 core 1.0sqmm thickness ,driver efficiency - 90% ,Applicable standard -withsatnd 160MPH wind velocity,colour-warm white,BIS certificate -Mandatory and manufacturer must have NABL accredited laboratory in house at manufacturing plant for electrical testing ,equipped witth all technical facilities ,LED driver manufacturig should be at plant as per direction of engineer incharge.

Erection of existing main feeder pillar with 125amps TPN front operatable type SDF unit in sheet steel enclosure with HRC fuses,100Amp 4Pole contactor with time swicth for automation /off,03Nos 63Amp TPN front opratable type SDF unit sheet steel enclosure with HRC fuses ,100Amp terminals block 4 ways ,voltmeter of range 0-500V ,indicating lamps with fuse and switch ,seperate insulators for fixing bus bars , connections , door hinges and removing dents from doors and other parts complete etc as required including interconnection with adequate size of copper cables and lugs /thimbles and painted with 1 coat of approed quality anticorrosie primer and 02 coats of superior quality alumium paint suitable paint suitable for operation in 415olt, 50Hz, 3 phase 4 wire AC supply & having cables ducts 4 Nos for incoming /outgoing cable size not more than 185 Sqmm complete set i/c erection in cement concerete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size) foundation including excavation and refilling etc complete as required as per direction of engineer in charge.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.