Regional Institute Of Medical Sciences Tender

Providing and fixing false ceiling at all height including providing and fixing of framework made of special sections, power pressed from MS Sheets and Galvanised with zinc coating of 120 gms/sqm(both side inclusive) as per IS:277 and consisting of angle cleat of size 25mm wide x 1.6 mm thick with flanges of 27mm flanges of 20mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230mm interval, including fixing of Gypmsum board to

12.5mm thick tampered edge Gypsum plain board conforming to IS:2095-Part I

Providing and fixing aluminium works for doors windows, ventilators and partions with extruded built up standard tubular sections/appropriate Z sections and other sections of approed make conforming to IS:733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up gaps at junctions, at top, bottom and side with required EPDM rubber/Neoprene gasket etc. Aluminium snap beading for glazing/panelling, C.P, brass/Stainless steel screws, all complete as per architectural drawing and the directions of Engineer-in-charge (Glazing and panelling to be paid for separately). for shutters of doors, windows & ventilators including, providing and fixing hinges/pivots and making provision for fixing of fitting wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately)

Annodised aluminium (anodised transparent or dyed to required shade according to IS : 1868, Minimum anodic coating of grade

Providing and fixing glazing in aluminium door, windows, ventilator shutters and partitions etc. with EPDM rudder/neoprene gasket etc. complete as per the architectural drawing and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 4mm thickness

Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS : 12823 Grade 1 Type II in and partition frames with C.P. brass/stainless steel screws etc. complete as par architectural drawing ang directions of engineer-in-charge.

Prelaminated particle board with decorative lamination on both.

Providing and laying Vitrified floor tiles in different sizes (thickness to be specified by the manufacturer ), with water absorption less than 0.08% and conforming to IS:15622,approved brand & manufacturer,in all colours and shade ,in laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand ), including grouting the joints with white cement and and matching pigments etc., complete Size of Tile -600 x600mm.

Size of tile 600x600 mm (Double charge)

White glazed tiles 10 mm thick in skirting risers of steps and dado on 10 mm thick plaster 1:3 (1 cem : 3coarse sand) and joined with white cement slurry.

Providing and applying plaster of paris putty of 2mm thickness over plastered surface to prepare the surface even and smooth complete.

Repairing to plaster including cutting the patch in proper shape and preparing the surface of the wall complete.

with cement mortar 1:4 (1 cem :4 fine sand)

Applying one coat of cement primer of approved quality on wall surface.

Painting (two or more coats) with plastic emulsion paint of approved quality on new work except walls to give an even shade.

P/F water closet squating pan (Indian type WC pan) with 100 mm Sand Cast P or S trap, 10 litre low level white PVC flushing Cistern, i/c flush pipe, manually controlled device (handle lever) conforming to IS:7231 with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:

Providing and fixing white vitreous china pedestal type water closet (European type WC pan) with seat and lid, 10 lit low level white PVC flushing cistern, including flushing pipe, with manually controlled device (handle lever), conforming to IS:7231, with all fittings and fixture complete, including cutting and making good the walls and floors wherever required:

WC pan with ISI marked white solid plastic seat and lid

Providing and fixing white vitreous chinaflat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and CP brass spreaders with brass unions and GI clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required:

One urinal basin with 5 lit white PVC automatic flushing cistern

P/F wash basin with CI brackets, 15mm CP brass pillar taps, 32mm CP brass waste of standard pattern, i/c painting of fittings and brackets, cutting and making good the walls wherever required.

White vitreous china wash basin size 630x450 mm with a pair of 15mm CP brass pillar taps

Providing and fixing Chlorinated Polyvinyle Chloride (CPVC) pipes having thermal stability for hot & cold water supply, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer in charge.

Internal work - Exposed on wall