Yashwantrao Chavan Maharashtra Open University Tender

Curved Table:- Providing & supplying on site as per Sample Approved by Architect and as per the instructions of The Engineer In Charge

Officer's Table of Size 1.60 x 0.75 m x 0.75 m Height :- Providing and fixing TOPAZ TABLE 1650 x 750 Overall Dimension - 1650x750x750 Primary Work Surface:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Softclosing access flap with in-build power box are provided on work surface for wire management. Secondary Work Surface:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Modesty Panel:Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Under- structure:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Integrated Pedestal:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedstal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestal is provided with lock for security.

Officer's Table of Size 2.10 x 1.10 m x 0.75 m Height :- Providing and fixing APO TOPAZ TABLE 2100 x 1100 with Overall Dimension - 2100x1100x750 Primary Work Surface:Made of corian top. Softclosing access flap with in-build power box are provided on work surface for wire management. Secondary Work Surface:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Modesty Panel:Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Under- structure:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Integrated Pedestal:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedstal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestal is provided with lock for security and this storages are needed on both sides.

Officer's Table of Size 2.35 x 1.15 m x 0.75 m Height :- Providing and fixing APO TOPAZ TABLE 2350 x 1150 with Overall Dimension - 2350x1150x750 Primary Work Surface:Made of corian top. Softclosing access flap with in-build power box are provided on work surface for wire management. Secondary Work Surface:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Modesty Panel:Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Under- structure:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Integrated Pedestal:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedstal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestal is provided with lock for security and this storages are needed on both sides.

Officer's Table of Size 2.35 x 1.15 m x 0.75 m Height with side unit:- Supplying and placing Topaz table in position Main Table,ERU & pedestal of the following specifications. Overall Dimension - 2350x2350x750 Primary Work Surface:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Softclosing access flap with in-build power box are provided on work surface for wire management. Secondary Work Surface:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Modesty Panel:Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Under- structure:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Integrated Pedestal:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedstal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestal is provided with lock for security. This product should be certified by GREENGUARD, Indoor Advantage GOLD & GREEN PRO.

Back Unit 1.65 m x 0.5 m x 0.750 m:- Supplying and placing in position ARISTO BCKUNT 1650W 750H Back unit of the following specifications.1650x500x750 Top Panel-Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Slide Door Unit-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping for body panels like side, bottom,back and shelves. Shutters are made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Shutters have a soft closing & anti slam mechanism. Handles are provided for ease of opening.Storage is provided with lock for security

Staff Tables 1.2 x 0.6 m:- Supplying and placing in position Aristo Main table of the following specifications.1200x600x750 Work Surface - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Gromet provided on work surface for wire management Modesty Panel - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Under-structure - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Hinge Door Storage - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Handle is provided for ease of opening. Storage is provided with cam lock for security.

Officer's Table of Size 1.65 x 0.75 m x 0.75 m Height with side unit:- Supplying and placing Aristo table in position Main Table,ERU & pedestal of the following specifications. 1650x1950x750 Primary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Soft closing access flap with in-build power box are provided on work surface for wire management Secondary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Modesty Panel Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Under structure Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Integrated Pedestal Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedestal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestals are provided with lock for security.

Officer's Table of Size 1.80 x 2.1 m x 0.75 m Height with side unit:- Supplying and placing in position Aristo Main Table,ERU & pedestal of the following specifications. 1800x2100x750 Primary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Soft closing access flap with in-build power box are provided on work surface for wire management Secondary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Modesty Panel Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Under structure Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Integrated Pedestal Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedestal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestals are provided with lock for security.

Centre Table:- Providing & fixing Bloom Centre/Coffee Table. Overall Size : Width : 100cm Depth : 65cm Height : 43cmTABLE MATERIALS: Glass of 08 mm thk tempered, Solid rubber woood legs and frame, MS sheet as bottom shelf .DECORATION MATERIALS & SPECIFICATIONS: (DENSITY / TYPE): PU coating to the rubber wood parts, clear glass

Corner Table:- Providing & fixing Bloom Corner Table.Overall Size : Width : 60cm Depth : 60cm Height : 45cmTABLE MATERIALS: Glass of 08 mm thk tempered, Solid rubber woood legs and frame, MS sheet as bottom shelf .DECORATION MATERIALS & SPECIFICATIONS: (DENSITY / TYPE): PU coating to the rubber wood parts, clear glass

Midback Chair - Type I :- Providing, supplying and placing Bravo Mid Back Chair. SEAT/BACK ASSEMBLY: The seat and back are made up of 1.2 ±0.1cm. thick hot-pressed plywood measured. upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured lumbar support for extra comfort. The seat has extra thick foam on front edge to give comfort to popliteal area. MID BACK SIZE 47.5 cm. (W) x 58.0 cm. (H). SEAT SIZE 47.0 cm. (W) x 48.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS: The one-piece armrests are injection moulded from black Co-polymer Polypropylene. CENTER TILT SYNCHRO MECHANISM : The mechanism is designed with the following features: ·360° revolving type. · Upight position locking · Tilt tension adjustmen. ·Seat/back tilting ratio of1:3. TUBULAR FRAME : The powder coated ( DFT 40-60 microns ) tubular frame is cantilever type & made of Ø 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. ER.W. Tube. PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm. TELESCOPIC BELLOW ASSEMBLY : The bellow is 3-piece telescopic type and injection moulded in black Polypropylene. PEDESTAL ASSEMBLY : The pedestal is injection moulded in black 33%glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.3 ±0.5cm. pitch-centre dia. (76.3 ±1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. Overall Dimensions of Chair WIDTH (W): 76.3 CM. DEPTH (D): 76.3 CM. HEIGHT (H): 85.5-97.5 CM. SEAT HEIGHT (SH): 42.5-54.5 CM.

Visitors Chair:- Providing, supplying and placing Bravo Visitor Chair. SEAT/BACK ASSEMBLY: The seat and back are made up of 1.2 ±0.1cm. thick hot-pressedplywood measured upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contouredlumbar support for extra comfort. The seat has extra thick foam on front edge to give comfort topopliteal area. MID BACK SIZE 47.5 cm. (W) x 58.0 cm. (H). SEAT SIZE 47.0 cm. (W) x 48.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded withdensity = 45±2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS :The one-piece armrests are injection moulded from black Co-polymer Polypropylene. TUBULAR FRAME : The powder coated ( DFT 40-60 microns ) tubular frame iscantilever type & made of Ø 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. ER.W. Tube. Overall Dimensions of Chair WIDTH (W): 61.4 CM. DEPTH (D): 64.5 CM. HEIGHT (H): 89.5 CM. SEAT HEIGHT (SH): 46.5 CM.

Side Credenza:- Providing & supplying ECHO - HDU-1200 W X 450 D X 740 H wooden storage comprised of a range of Low height to medium height wooden HDU and SDU as per attasched DMX drg. Body : Body is made from 18mm PLB with all the edges sealed with 0.8 mm thick PVC Edgeband. The Back panel is 9mm White PLT. The entire construction is ready to assemble unit and is assembled with suitable KD fittings. The shelves and separator panels ( if available ) is made from 18 mm white PLT and edges are sealed with 0.8 mm edge band. The bottom shelf is fixed and other shelves have one step adjustment for optimizing the space. Doors : Door Panels ae made from 18 mm PLB with 2 mm Edge band on all edges ad a flush Plastic handle is fitted vertically at the center of the door. The hinge door has suitable hinges and HDU is fitted with an adjustable fitting for height adjustment. The SDU runs in a PVC track mounted on the TOP and Bottom panel of the Body. HDU has a three point lock and SDU has a push type lock. All the storages are fitted with a 6 mm leveler at bottom for leveling.

Metal Storages:- Providing and fixing Gain Pro storage cabinet body-Product Size - 900(W) x 450(D) x 1950*(H) (Height of leveler is 50mm and adjustment possible is 15mm.) Construction & Material - Aesthetically appealing completely knock down construction. The add-on units are stack widthwise to form arow of storage. Legs fitted with screw type leveler. Made from combination of Top panel(0.5mm CRCA), side panel(0.5mm CRCA), Bottom panel(0.5mm CRCA for 450W/600W and 0.8mm CRCA for 900W/1200W), Back panel(0.5mm CRCA), Top Bottom stiffener(1.2mm CRCA) and End Cover(0.5mm CRCA). ** - CRCA 'D' Grade as per IS-513 Shelving - It is a 12 bend panel made of 0.7mm Thick CRCA (D Grade, IS-513) Each shelf has max Load Capacity of - 55kg UDL for 900W unit and 4 Nos. of fixed shelves for 1950(H). A4 size Box file (85Wx340Hx285D) can be stored vertically on all loading levels 900 w = 10 no of files. Finish - Epoxy Polyester Powder coated to the thickness of 50 microns (+/-10 micron). Door-Product Size - 2 Doors (LH and RH) for 900W For 900W storage-Each Door width 448W Construction & Material - Made from 0.6mm Thick CRCA (D Grade, IS-513) Soft closing Hinge Handle - Asthetically appealing handle made of Aluminum Cam Lock - -3 Way locking provision. - Click action mechanism. - Key removable in locked and unlocked positions. - Zinc alloy die cast housing. Shelving - It is a 12 bend panel made of 0.7mm Thick CRCA (D Grade, IS-513) Each shelf has max Load Capacity of - 55kg UDL for 900W unit 4 Nos. of fixed shelves for 1950(H) A4 size Box file (85Wx340Hx285D) can be stored vertically on all loading levels (Refer Sheet 4 of 17) Number of files that can be stored in one shelf is as follows: 900 w = 10 no of files Finish - Epoxy Polyester Powder coated to the thickness of 50 microns (+/-10 micron).

Glassdoor Storages:- Providing and fixing Gain Pro Glassdoor Storage. Product Size - 900(W) x 450(D) x 1950*(H) Height of leveler is 50mm and adjustment possible is 15mm. Construction & Material - Aesthetically appealing completely knock down construction. The add-on units are stack widthwise to form arow of storage. Legs fitted with screw type leveler. Made from combination of Top panel(0.5mm CRCA), side panel(0.5mm CRCA), Bottom panel(0.5mm CRCA for 0.8mm CRCA for 900W), Back panel(0.5mm CRCA), Top Bottom stiffener(1.2mm CRCA) and End Cover(0.5mm CRCA). ** - CRCA 'D' Grade as per IS-513, Shelving - It is a 12 bend panel made of 0.7mm Thick CRCA (D Grade, IS-513) Each shelf has max Load Capacity of - 55 kg for 900W unit with 4 Nos. of fixed shelves for 1950(H). A4 size Box file (85Wx340Hx285D) can be stored vertically on all loading levels. Number of files that can be stored in one shelf is as follows: 900 w = 10 no of files Finish - Epoxy Polyester Powder coated to the thickness of 50 microns (+/-10 micron). DOOR-Construction & Material - Made from the combination of aluminium alloy (63400) extrusion and clear glass. Soft closing Hinge. Handle - Asthetically appealing handle made of Aluminum Cam Lock- 3 Way locking provision, Click action mechanism, Key removable in locked and unlocked positions, Zinc alloy die cast housing. Shelving - It is a 12 bend panel made of 0.7mm Thick CRCA.

Sofas back to back :- Providing and supplying Graph B2B sofas W 120.0 D 133.5 H 79.0 SH 44.0 SEATS:- Understructure is made using a combination of 12mm Plywood (As per IS:303) vertical panels and Pine-Wood longitudinal members. 2mm thk kraft-board is stapled on the front side for foam sticking surface.Seat is made with 100mm PU Slab-stock foam pasted on the seat ply. 12mm PU Slab-stock foam is pasted along the front and sides. The seat is upholstered in fabric.1200mm, 1500mm, and 1800mm Length Sofas are provided with 02 nos of 6A electrical sockets with individual switches on each seat. 900 Length Sofas are provided with 01 nos of 5A electrical sockets with individual switch on each seat. The Electricals are safely housed in a box mounted on Pine-wood section within the seat & power is supplied through a 1.5 mtr AC cord with ceramic fuse (5A). BACK:- Understructure is made using a combination of 12mm Plywood (As per IS:303) vertical panels and Pine-Wood longitudinal members. 2mm thik MDF-board is stapled on the both sides as back foam sticking surface. Back is made with 50mm PU Slab-stock foam on both front and back, while 12mm PU Slab-stock foam is pasted along the sides. The back is upholstered in fabric. LEGS:- The legs are made using seasoned FSC-certified seasoned Teak-Wood finished with a clear matt coat of PU Lacquer. ASSEMBLY-The Seat and Back are connected using Bolts, Washers & Nuts. Legs are assembled using Bolts, Washers & Drive-in T-Nuts

Single Sofa :- Providing and supplying Graph Single Sofa W 120.0 D 70.5 H 79.0 SH 44.0 SEAT : • Understructure is made using a combination of 12mm Plywood (As per IS:303) vertical panels and Pine-Wood longitudinal members. 2mm thk kraft-board is stapled on the front side for foam sticking surface. • Seat is made with 100mm PU Slab-stock foam pasted on the seat ply. 12mm PU Slab-stock foam is pasted along the front and sides. • The seat is upholstered in fabric. 1200mm, 1500mm, and 1800mm Length Sofas are provided with 02 nos of 6A electrical sockets with individual switches. 900 Length Sofas are provided with 01 nos of 6A electrical sockets with individual switch. The Electricals are safely housed in a box mounted on Pine-wood section within the seat & power is supplied through a 1.5 mtr AC cord with ceramic fuse (5A). BACK: • Understructure is made using a combination of 12mm Plywood (As per IS:303) vertical panels and Pine-Wood longitudinal members. 2mm thk MDF-board is stapled on the front & back side for foam sticking surface. • Back is made with 50mm PU Slab-stock foam, while 12mm PU Slab-stock foam is pasted along the back and sides. • The back is upholstered in fabric. LEGS : The legs are made using FSC-certified seasoned Teak-Wood finished with a clear matt coat of PU Lacquer. ASSEMBLY. • The Seat and Back are connected using Bolts, Washers & Nuts. Legs are assembled using Bolts, Washers & Drive-in T-Nuts.

Breakout Area Chair:- Providing and fixing of Greet Chairs SEAT: The seat is made up of synthetic leather upholstered on PU slabstock foam of 6.5 cm (±0.5 cm). It is which is fitted to the upholstered wooden batten box by bolting from the inside. Holding plate is made of HR Steel of 0.3 cm (±0.02 cm) thickness as per IS:2062 which is bolted to the upholstered seat assembly SEAT SIZE: 42.0 cm. (W) x 42.0 cm. (D) CASING OF TETRIS- Casing of the flip type of Tetris is made up of 01 cm (±0.02 cm) M.S. rod as per IS:9550 Casing is powder coated (DFT 40-60 microns). Also casing is coated with nano coat to improve the abrasion resistance of the surface. CASING SIZE 44.0 cm. (W) x 44.0 cm. (D) x 37.5 (H) WOODEN BATTEN BOX ASSEMBLY- Side panels of batten box is made up of 0.9 cm (±0.05 cm) plywood as per IS:303 The four corners of batten box is made up of solid wood which forms the radius. Bottom portion of batten box is covered by 1.2 cm (±0.05cm) rubber wood panel which is finished with a clear matt coat of PU lacquer Sides of wooden batten box is upholstered with synthetic leather with backing of PU slabistock foam of 0.6 cm. Upholstered wooden box can be flipped in the reverse way to use it as desk surface by keping it on the casing. BATTEN BOX SIZE: 40.0cm (W) x 40.0 cm (D) x 274 cm (H)

Midback Chair - Type II :- Providing, supplying and placing Greta 2.0 Chair Mid Back Chair. SEAT ASSEMBLY: The seat is made up of 1.5±0.1 cm thick hot-pressed plywood upholstered with fabric and moulded polyurethane foam. SEAT SIZE: 51.8cm (W) x 49.7cm (D), BACK ASSEMBLY: The Back is injection moulded in glass filled Polypropylene which is 2 upholstered with Mesh fabric. The back consist of adjustable Lumbar support made of injection moulded Polypropylene having an adjustment of 5.0 10.1 cm. BACK SIZE: 47.9 cm(W) x 66.9 cm (H). HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane seat foam is moulded with density 45+/-2 kg/m and hardness 14 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS (ADJUSTABLE):The height adjustable armrest is made of Polypropylene and can be adjusted to 6.010.1cm height it also has swivel and To and Fro adjustment with moulded PU. ACTIVE BIO-SYNCHRO MECHANISM: The adjustable tilting mechanism is designed with the following features 360° revolving type. Front-pivot for tilt with feet resting on ground & continuous lumber support ensuring more comfort Till tension adjustment can be operated in seating position 5 position Tilt limiter giving option of variable sit angle to the chair Seat/back tilting ratio of 1:2. The mechanism housing is made up of HPDC Aluminium & black powder coated (DFT 40 to 60 micron). PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment with an adjustment stroke of 10.0±0.3cm. PEDESTAL ASSEMBLY: The pedestal is injection moulded in black 30% glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal pitch-center dia is 166.1±0.5 cm.(76.1 ± 1.0 cm. with castors). TWIN WHEEL CASTORS: The twin wheel castors are Injection moulded in black Polyamide having 6.01 0.1cm wheel Diameter. WIDTH (W) - 76.0cm, DEPTH (D) - 76.0cm, HEIGHT (H) - 95.5 cm- 105.5cm, SEAT HEIGHT - 43.5 - 54.0cm This product should be certified by Indoor Advantage GOLD, GREENGUARD GOLD, BIFMA LEVEL 2 & GREENPRO.

Highback Chair:- Providing, supplying and placing Greta 2.0 Chair SEAT ASSEMBLY: The seat is made up of 1.5±0.1 cm thick hot-pressed plywood upholstered with fabric and moulded polyurethane foam. SEAT SIZE: 51.8cm (W) x 49.7cm (D). BACK ASSEMBLY: The Back is injection moulded in glass filled Polypropylene which is 2 upholstered with Mesh fabric. The back consist of adjustable Lumbar support made of injection moulded Polypropylene having an adjustment of 5.0 10.1 cm. BACK SIZE: 47.9 cm(W) x 66.9 cm (H), HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane seat foam is moulded with density 45+/-2 kg/m and hardness 14 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS (ADJUSTABLE):The height adjustable armrest is made of Polypropylene and can be adjusted to 6.010.1cm height it also has swivel and To and Fro adjustment with moulded PU aNoop. ACTIVE BIO-SYNCHRO MECHANISM: The adjustable tilting mechanism is designed with the following features 360° revolving type Front-pivot for tilt with feet resting on ground & continuous lumber support ensuring more comfort Till tension adjustment can be operated in seating position. 5 position Tilt limiter giving option of variable sit angle to the chair Seat/back tilting ratio of 1:2 The mechanism housing is made up of HPDC Aluminium & black powder coated (DFT 40 to 60 micron). PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment with an adjustment stroke of 10.0±0.3cm. PEDESTAL ASSEMBLY: The pedestal is injection moulded in black 30% glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal pitch-center dia is 166.1±0.5 cm.(76.1 ± 1.0 cm. with castors). TWIN WHEEL CASTORS: The twin wheel castors are Injection moulded in black Polyamide having 6.01 0.1cm wheel Diameter. HEADREST: The Headrest sub-assembly is made up of injection moulded glass filled Polypropylene which is upholstered with moulded HR polyurethane foam and fabric. It has an adjustment of 3.0 ± 0.1cm & it is assembled over GRETA 2.0 Full back chair.The complete headrest assembly is retro fit to the main chair. WIDTH (W) - 76.0cm, DEPTH (D) - 76.0cm, HEIGHT (H) - 113.0 cm- 123.0cm, SEAT HEIGHT - 43.5 - 54.0cm

3 Seater Waiting Chair :- Providing and Fixing Matrix 3 seater waiting chair SEAT SHELL :The seat shell should be a welded assembly of seat,back and side frame. The seat and back should be made of 0.12±0.013cm thk CR steel sheet with oblong perforations.They should be welded to sideframe of size 3.2±0.05cm x 0.5 ± 0.05 cm thk HR steel.The welded assembly should be powder coated ( DFT 40-60 microns ). The seat has a front water fall edge to provide popliteal clearance for comfortable seating. It also has a buttock support curve that not only provides rear support but also prevents small children from falling through the gap between seat and back. Clean and flat surfaces of seat and back aids in easy maintenance. * SEAT SIZE : 47.8 cm (W) x 44.6 cm (D) * BACK SIZE : 41.6 cm (W) x 23.0 cm (H) Understructure assembly consshould be ts of connecting beam and leg assembly made of M.S. E.R.W. oblong tube of size 7.5±0.03cm x 2.5±0.03cm x 0.2±0.016cm thk.The welded structure assembly should be powder coated ( DFT 40-60 microns ).The leg assembly should be fitted with shoes and levellers in Nylon. The leg structure should be designed with minimal should be a of contact close to ground providing easy access for cleaning purposes. The shoes fitted to leg assembly help in aligning the structure for back to back arrangements. Levellers take cshould be of uneven flooring.Connecting beam should be fitted with snap locking end cap.lt also aids in side-by-side understructure alignment . Armrest assembly consshould be ts of armrest frame and armrest pad . The armrest frame should be made up of size 3.175±0.05cm x 0.47±0.027cm thk HR steel and it should be powder coated ( DFT 40-60 microns ). Armrest pad should be injection molded in Nylon and should be fitted onto the armrest frame. Overall Dimensions of Chair: Seat Height - 44.1 cm., Height - 78.5 cm., Width & Depth of Chair as - Width-169.5cm and Depth-63.8 cm.

AV Storage Rack:- Providing and supplying Mingle AV Storage unit 583 X 670 X 740 CARCASS-Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 0.8 mm thick PVC lipping. Pilot holes provided for fixing 12U AV equipment rack. 1 Nos 12U rack fits into one unit of 112 storage. 3 Nos 12U racks fit into one unit of 312 storage. GLASS-5mm thk toughened, grey tinted glass with crystal edge polish finish is used as shutter. They are fitted with self closing hinges with soft close dampner for smooth operation. BACK VENT PANEL-A panel made of 0.8mm CRCA MS IS:513, epoxy polyester powder coated (DFT 40-60 microns) is used for ventilation. The size of the panel is different for both the modules. CASTORS-Castors (4nos.) are provided at the bottom to enable mobility of the unit as required for 112 unit Castors (5nos.) are provided at the bottom to enable mobility of the unit as required for 312 unit.Castors (5nos.) are provided at the bottom to enable mobility of the unit as required for 312 unit.

Conference Table of Size - 3.60 x 1.50 m :- Providing and supplying Mingle Membrane Unitised 12 seater table of size 3600 X 1500 X 740.Work top--Made of 25mm thick MDF­one side pre­laminate board conforming to IS­14587:1998 with 0.4mm PVC membrane pressed on to top and having chamfered edge. Access panels provided with soft closing hinges. Understructure-The Under-structure consists of mixture of 25mm and 18mm Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Anodised aluminium alloy 63400 - WP profile is added at bottom edges for improving the aesthetics. The product has a knock-down construction. Wire Management-Bottom cabinet with door is provided for flow of wires and cables. Cutout provision below Access flap at four locations for standard 8 module Anchor Roma is provided. Beside each cutout, an additional cutout with plate is provided for mounting Audio Visual Cables (eg. HDMI,VGA-A,etc).

Conference Table of Size - 2.10 x 1.15 m:- Providing and supplying Mingle Membrane Unitised 6 seater table of size 2100 X 1150 X 740.Work top--Made of 25mm thick MDF­one side pre­laminate board conforming to IS­14587:1998 with 0.4mm PVC membrane pressed on to top and having chamfered edge. Access panels provided with soft closing hinges. Understructure-The Under-structure consists of mixture of 25mm and 18mm Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Anodised aluminium alloy 63400 - WP profile is added at bottom edges for improving the aesthetics. The product has a knock-down construction. Wire Management-Bottom cabinet with door is provided for flow of wires and cables. Cutout provision below Access flap at four locations for standard 8 module Anchor Roma is provided. Beside each cutout, an additional cutout with plate is provided for mounting Audio Visual Cables (eg. HDMI,VGA-A,etc).

Pedestals:- Providing & supplying NOVA STANDING PEDESTAL WITH FLAT METAL FRONT OF SIZE 390W X 585D X 646HT, 1DR = 1 BOX + 1 FILE, CENTRAL LOCKING. Construction material: CRCA 0.8 mm thick body & stiffner, 1.2 mm thick for top & bottom stiffner, 0.6 mm for metal top. Epoxy polyster powder coated to the thickness of 50 microns.

Compactor 1 bay: Providing and fixing Optimiser plus Overall Dimensions of SS1 - Single Static 1 Bay Push Pull Type (U/C + Fittings) shall be 1200mm(W)x400mm(D)x2083mm(H). The Construction shall be rigid knock down made out of 0.8 thick CRCA steel conforming to IS : 513.Each body shall have a main unit plus add on units (1,2,3,4,5). Final finish consists of epoxy polyester powder coating of approved color & shade with a Dry Film Thickness of minimum 40 microns.Shelf construction made of 0.7 thk CRCA steel conforming to IS: 513 Gr.D or DD.Uniformly distributed load capacity of 100 Kg . Undercarriage shall have construction in welded frame CRCA sheet 2 mmthk conforming to IS:513. The movements of the system shall be Push pull configuration (TYPE-P1/TYPE-P2) : Movement of units achieved by pushing or pulling 'C' tyep plastic handle (mounted on each double & single movable units) & rigidly fixed at suitable height on body side. y. Each movable body also has an understructure with 4 nos. of antifriction ball bearings for rolling on channels. The twin moving body, i.e. TM, has 4 nos. of bearing fitted horizontally to restrict the lateral movement of the body on rail while the single moving body, i.e. SL, body has 2 nos. of a special anti-tilt bearing assembly fitted to the understructure which not only restricts lateral movement but also prevents SL from toppling. A Centralized locking arrangement is provided through Locking Stiffener mounted onto back of Single Last unit, i.e. SL body. It gets locked into the channels when all the units are brought together, and the lock is turned. The Recess handle lock is of Godrej make & placed at a height of 940mm from ground level. The locking stiffener is made of 1.2 mm thk conforming to IS:513.Hinged doors have Recessed Die cast Handle cum lock with 3 way locking through a lever & shooting bolts.The nuts & bolts are galvanized / blackodized / Zn Plated. Label Holder: It is an aluminium extrusion of length 396mm for LD/SD and 796mm for TD, fitted on to front cover of body. The Paper is 300GSM matt milky white sticker paper, to be inserted into the aluminium extrusion. The length of paper is 394mm for LD/SD and 794mm for TD. Over that a transparent plastic of corresponding length of 150-200 micron polythene is to be inserted. Overall Dimensions of SL1 - Single last 1 Bay Push Pull Type (U/C + Fittings) shall be 1200mm(W)x400mm(D)x2083mm(H). The Construction shall be rigid knock down made out of 0.8 thick CRCA steel conforming to IS : 513.Each body shall have a main unit plus add on units (1,2,3,4,5). Final finish consists of epoxy polyester powder coating of approved color & shade with a Dry Film Thickness of minimum 40 microns.Shelf construction made of 0.7 thk CRCA steel conforming to IS: 513 Gr.D or DD.Uniformly distributed load capacity of 100 Kg . Undercarriage shall have construction in welded frame CRCA sheet 2 mmthk conforming to IS:513. The movements of the system shall be Push pull configuration (TYPE-P1/TYPE-P2) : Movement of units achieved by pushing or pulling 'C' tyep plastic handle (mounted on each double & single movable units) & rigidly fixed at suitable height on body side.Each movable body also has an understructure with 4 nos. of antifriction ball bearings for rolling on channels. The twin moving body, i.e. TM, has 4 nos. of bearing fitted horizontally to restrict the lateral movement of the body on rail while the single moving body, i.e. SL, body has 2 nos. of a special anti-tilt bearing assembly fitted to the understructure which not only restricts lateral movement but also prevents SL from toppling. A Centralized locking arrangement is provided through Locking Stiffener mounted onto back of Single Last unit, i.e. SL body. It gets locked into the channels when all the units are brought together, and the lock is turned. The Recess handle lock is of Godrej make & placed at a height of 940mm from ground level. The locking stiffener is made of 1.2 mm thk conforming to IS:513.Hinged doors have Recessed Die cast Handle cum lock with 3 way locking through a lever & shooting bolts.The nuts & bolts are galvanized / blackodized / Zn Plated. Label Holder: It is an aluminium extrusion of length 396mm for LD/SD and 796mm for TD, fitted on to front cover of body. The Paper is 300GSM matt milky white sticker paper, to be inserted into the aluminium extrusion. The length of paper is 394mm for LD/SD and 794mm for TD. Over that a transparent plastic of corresponding length of 150-200 micron polythene is to be inserted. Overall Dimensions of TM1 - Twin Mobile 1 Bay Push Pull Type(U/C + Fittings + Handle) shall be 915mm(W)x762mm(D)x2083mm(H).The Construction shall be rigid knock down made out of 0.8 thick CRCA steel conforming to IS : 513 . Each body shall have a main unit plus add on units (1,2,3,4,5) . Finish shall be Epoxy polyester powder coated thickness of 40 microns . Shelf construction shall be made from CRCA steel 0.7 mm thick IS :513 .Uniformly distributed load capacity of 60 Kg . Undercarriage shall have construction in welded frame CRCA sheet 2 mmthk conforming to IS:513. TThe movements of the system shall be Push pull configuration (TYPE-P1/TYPE-P2) : Movement of units achieved by pushing or pulling 'C' tyep plastic handle (mounted on each double & single movable units) & rigidly fixed at suitable height on body side. Each movable body also has an understructure with 4 nos. of antifriction ball bearings for rolling on channels. The twin moving body, i.e. TM, has 4 nos. of bearing fitted horizontally to restrict the lateral movement of the body on rail while the single moving body, i.e. SL, body has 2 nos. of a special anti-tilt bearing assembly fitted to the understructure which not only restricts lateral movement but also prevents SL from toppling. A Centralized locking arrangement is provided through Locking Stiffener mounted onto back of Single Last unit, i.e. SL body. It gets locked into the channels when all the units are brought together, and the lock is turned. The Recess handle lock is of Godrej make & placed at a height of 940mm from ground level. The locking stiffener is made of 1.2 mm thk conforming to IS:513.Hinged doors have Recessed Die cast Handle cum lock with 3 way locking through a lever & shooting bolts.The nuts & bolts are galvanized / blackodized / Zn Plated. Label Holder: It is an aluminium extrusion of length 396mm for LD/SD and 796mm for TD, fitted on to front cover of body. The Paper is 300GSM matt milky white sticker paper, to be inserted into the aluminium extrusion. The length of paper is 394mm for LD/SD and 794mm for TD. Over that a transparent plastic of corresponding length of 150-200 micron polythene is to be inserted. // When the last unit is twin movable , hinged doors are provided for the end bodies, so in this case locking stiffener is mounted onto twin unit. It consists of ‘C’ section 2 mm thk HR sheet & Square 25.4mm X 2mm thk ERW tube – both connected by screws. Prior to the grouting of the guide channels with the help of raul plug & screw, ensure the ground is level. The rail channels are of 3 lengths i.e., 800mm, 1600mm and 2400mm.

Compactor 3 bay:- Providing and fixing Optimiser plus Overall Dimensions of SD 3 Single Drive Cover Unit 3 Bay(U/C + Fittings + Cover) shall be 3600mm(W) x 400mm(D) x 2113mm(H). The Construction shall be rigid knock down made out of 0.8 thick CRCA steel conforming to IS:513, Gr.D. Each body shall have 1 main unit plus add on units (0,1,2,3 depending on no. of bays 1, 2, 3, 4 respectively) . Finish shall be Epoxy polyester powder coated thickness of 40 microns . Shelf construction shall be with 12 bend panel made from CRCA steel 0.7 mm thick IS:513, Gr.D .Uniformly distributed load capacity of 100 Kg . Undercarriage shall have construction in welded frame made of HR sheet 3 mm thick conforming to IS : 2062. The Movements shall be Drive Type configuration : In case of D2,D3 & D4 movement of units is achieved mechanically through a PU Hand Wheel and Sprocket-Chain arrangement mounted rigidly onto body size. For D3 each movable undercarriage shall be provided with 3 driving rollers and 3 driven rollers.LD understructure has 2 nos. of anti-tilt bearing assembly.The roller assembly comprises of a die-cast step wheel, 2 deep-groove ball bearings and a MS shaft. The step wheel is made of cast steel and is fitted onto the MS shaft using a feather key. The two ball bearings are then fastened on either side of the step wheel using circlips. This entire roller assembly is then snap-fitted into a wheel housing. The wheel housing is fixed in the U-channel of the understructure using machine screws. This wheel-housing is made of engineering plastic material made by injection-molding process. The entire roller assembly is designed to withstand the maximum loads of the body. Fittings shall be centralized locking arrangement through Lock which is operated by spring mechanism mounted onto understructure of last drive unit. The lock is made of 0.8 mm thick conforming to IS:513..The ‘sprocket-chain’ arrangement is covered by a 1 mm thk. CRCA sheet Drive Unit Cover with dimensions 1202mm x 398mm x 87mm and is fixed onto the side of the body. The PU handwheel is rigidly fixed at suitable height on side of the body & projects out of cover by another 99.0 mm. Fixed unit (SD) does not have the Drive Unit Cover. When the last Body is Twin Drive, i.e., TD, hinged doors are provided for the last body. In this scenario the centralized locking system is fitted on the last TD body. Each Drive Type units shall have Locking Knob near the drive wheel for manual locking of individual units when a person is using those units. Knob shall be rotated to unlock position when units are to be moved. End stoppers shall be provided to prevent derailment.The nuts & bolts are galvanized / blackodized / Zn Plated. Also total no. of loading levels per understructure shall be 15 for SD3. Label holder - It is an aluminium extrusion of length 396mm for LD/SD and 796mm for TD, fitted on to front cover of body. The Paper is 300GSM matt milky white sticker paper, to be inserted into the aluminium extrusion. The length of paper is 394mm for LD/SD and 794mm for TD. Over that a transparent plastic of corresponding length of 150-200 micron polythene is to be inserted. Overall Dimensions of LD 3 Single Drive Cover Unit 3 Bay(U/C + Fittings + Cover) shall be 3600mm(W) x 400mm(D) x 2113mm(H). The Construction shall be rigid knock down made out of 0.8 thick CRCA steel conforming to IS:513, Gr.D. Each body shall have 1 main unit plus add on units (0,1,2,3 depending on no. of bays 1, 2, 3, 4 respectively) . Finish shall be Epoxy polyester powder coated thickness of 40 microns . Shelf construction shall be with 12 bend panel made from CRCA steel 0.7 mm thick IS:513, Gr.D .Uniformly distributed load capacity of 100 Kg . Undercarriage shall have construction in welded frame made of HR sheet 3 mm thick conforming to IS : 2062. The Movements shall be Drive Type configuration : In case of D2,D3 & D4 movement of units is achieved mechanically through a PU Hand Wheel and Sprocket-Chain arrangement mounted rigidly onto body size. For D3 each movable undercarriage shall be provided with 3 driving rollers and 3 driven rollers.LD understructure has 2 nos. of anti-tilt bearing assembly.The roller assembly comprises of a die-cast step wheel, 2 deep-groove ball bearings and a MS shaft. The step wheel is made of cast steel and is fitted onto the MS shaft using a feather key. The two ball bearings are then fastened on either side of the step wheel using circlips. This entire roller assembly is then snap-fitted into a wheel housing. The wheel housing is fixed in the U-channel of the understructure using machine screws. This wheel-housing is made of engineering plastic material made by injection-molding process. The entire roller assembly is designed to withstand the maximum loads of the body. Fittings shall be centralized locking arrangement through Lock which is operated by spring mechanism mounted onto understructure of last drive unit. The lock is made of 0.8 mm thick conforming to IS:513..The ‘sprocket-chain’ arrangement is covered by a 1 mm thk. CRCA sheet Drive Unit Cover with dimensions 1202mm x 398mm x 87mm and is fixed onto the side of the body. The PU handwheel is rigidly fixed at suitable height on side of the body & projects out of cover by another 99.0 mm. Last unit (LD) have the Drive Unit Cover. When the last Body is Twin Drive, i.e., TD, hinged doors are provided for the last body. In this scenario the centralized locking system is fitted on the last TD body. Each Drive Type units shall have Locking Knob near the drive wheel for manual locking of individual units when a person is using those units. Knob shall be rotated to unlock position when units are to be moved. End stoppers shall be provided to prevent derailment.The nuts & bolts are galvanized / blackodized / Zn Plated. Also total no. of loading levels per understructure shall be 15 for LD3. Label holder - It is an aluminium extrusion of length 396mm for LD/SD and 796mm for TD, fitted on to front cover of body. The Paper is 300GSM matt milky white sticker paper, to be inserted into the aluminium extrusion. The length of paper is 394mm for LD/SD and 794mm for TD. Over that a transparent plastic of corresponding length of 150-200 micron polythene is to be inserted. Overall Dimensions of TD 3 Single Drive Cover Unit 3 Bay(U/C + Fittings + Cover) shall be 3600mm(W) x 800mm(D) x 2113mm(H). The Construction shall be rigid knock down made out of 0.8 thick CRCA steel conforming to IS:513, Gr.D. Each body shall have 1 main unit plus add on units (0,1,2,3 depending on no. of bays 1, 2, 3, 4 respectively) . Finish shall be Epoxy polyester powder coated thickness of 40 microns . Shelf construction shall be with 12 bend panel made from CRCA steel 0.7 mm thick IS:513, Gr.D .Uniformly distributed load capacity of 100 Kg . Undercarriage shall have construction in welded frame made of HR sheet 3 mm thick conforming to IS : 2062. The Movements shall be Drive Type configuration : In case of D2,D3 & D4 movement of units is achieved mechanically through a PU Hand Wheel and Sprocket-Chain arrangement mounted rigidly onto body size. For D3 each movable undercarriage shall be provided with 3 driving rollers and 3 driven rollers.LD understructure has 2 nos. of anti-tilt bearing assembly.The roller assembly comprises of a die-cast step wheel, 2 deep-groove ball bearings and a MS shaft. The step wheel is made of cast steel and is fitted onto the MS shaft using a feather key. The two ball bearings are then fastened on either side of the step wheel using circlips. This entire roller assembly is then snap-fitted into a wheel housing. The wheel housing is fixed in the U-channel of the understructure using machine screws. This wheel-housing is made of engineering plastic material made by injection-molding process. The entire roller assembly is designed to withstand the maximum loads of the body. Fittings shall be centralized locking arrangement through Lock which is operated by spring mechanism mounted onto understructure of last drive unit. The lock is made of 0.8 mm thick conforming to IS:513..The ‘sprocket-chain’ arrangement is covered by a 1 mm thk. CRCA sheet Drive Unit Cover with dimensions 1202mm x 398mm x 87mm and is fixed onto the side of the body. The PU handwheel is rigidly fixed at suitable height on side of the body & projects out of cover by another 99.0 mm. When the last Body is Twin Drive, i.e., TD, hinged doors are provided for the last body. In this scenario the centralized locking system is fitted on the last TD body. Each Drive Type units shall have Locking Knob near the drive wheel for manual locking of individual units when a person is using those units. Knob shall be rotated to unlock position when units are to be moved. End stoppers shall be provided to prevent derailment.The nuts & bolts are galvanized / blackodized / Zn Plated. Also total no. of loading levels per understructure shall be 30 for TD3. Label holder - It is an aluminium extrusion of length 396mm for LD/SD and 796mm for TD, fitted on to front cover of body. The Paper is 300GSM matt milky white sticker paper, to be inserted into the aluminium extrusion. The length of paper is 394mm for LD/SD and 794mm for TD. Over that a transparent plastic of corresponding length of 150-200 micron polythene is to be inserted. CRCA Steel conforming to IS: 513 Gr.D. This assembly is available for both heights – 1980H and 2361H.

Compactor 4 bay:- Providing and fixing Optimiser plus Providing, suplying and placing of stoarge unit.Overall Dimensions of SD 4 Single Drive Cover Unit 4 Bay(U/C + Fittings + Cover) shall be 4800mm(W) x 400mm(D) x 2113mm(H). The Construction shall be rigid knock down made out of 0.8 thick CRCA steel conforming to IS:513, Gr.D. Each body shall have 1 main unit plus add on units (0,1,2,3 depending on no. of bays 1, 2, 3, 4 respectively) . Finish shall be Epoxy polyester powder coated thickness of 40 microns . Shelf construction shall be with 12 bend panel made from CRCA steel 0.7 mm thick IS:513, Gr.D .Uniformly distributed load capacity of 100 Kg . Undercarriage shall have construction in welded frame made of HR sheet 3 mm thick conforming to IS : 2062. The Movements shall be Drive Type configuration : In case of D2,D3 & D4 movement of units is achieved mechanically through a PU Hand Wheel and Sprocket-Chain arrangement mounted rigidly onto body size. For D3 each movable undercarriage shall be provided with 3 driving rollers and 3 driven rollers.LD understructure has 2 nos. of anti-tilt bearing assembly.The roller assembly comprises of a die-cast step wheel, 2 deep-groove ball bearings and a MS shaft. The step wheel is made of cast steel and is fitted onto the MS shaft using a feather key. The two ball bearings are then fastened on either side of the step wheel using circlips. This entire roller assembly is then snap-fitted into a wheel housing. The wheel housing is fixed in the U-channel of the understructure using machine screws. This wheel-housing is made of engineering plastic material made by injection-molding process. The entire roller assembly is designed to withstand the maximum loads of the body. Fittings shall be centralized locking arrangement through Lock which is operated by spring mechanism mounted onto understructure of last drive unit. The lock is made of 0.8 mm thick conforming to IS:513..The ‘sprocket-chain’ arrangement is covered by a 1 mm thk. CRCA sheet Drive Unit Cover with dimensions 1202mm x 398mm x 87mm and is fixed onto the side of the body. The PU handwheel is rigidly fixed at suitable height on side of the body & projects out of cover by another 99.0 mm. Fixed unit (SD) does not have the Drive Unit Cover. When the last Body is Twin Drive, i.e., TD, hinged doors are provided for the last body. In this scenario the centralized locking system is fitted on the last TD body. Each Drive Type units shall have Locking Knob near the drive wheel for manual locking of individual units when a person is using those units. Knob shall be rotated to unlock position when units are to be moved. End stoppers shall be provided to prevent derailment.The nuts & bolts are galvanized / blackodized / Zn Plated. Also total no. of loading levels per understructure shall be 20 for SD4. Label holder - It is an aluminium extrusion of length 396mm for LD/SD and 796mm for TD, fitted on to front cover of body. The Paper is 300GSM matt milky white sticker paper, to be inserted into the aluminium extrusion. The length of paper is 394mm for LD/SD and 794mm for TD. Over that a transparent plastic of corresponding length of 150-200 micron polythene is to be inserted. This product should be certified By GRIHA & SVAGRIHA , GREEN PRO, GREENGUARD, Indoor Advantage GOLD Providing, suplying and placing of stoarge unit.Overall Dimensions of LD42 Single Drive Cover Unit 4 Bay(U/C + Fittings + Cover) shall be 4800mm(W) x 400mm(D) x 2113mm(H). The Construction shall be rigid knock down made out of 0.8 thick CRCA steel conforming to IS:513, Gr.D. Each body shall have 1 main unit plus add on units (0,1,2,3 depending on no. of bays 1, 2, 3, 4 respectively) . Finish shall be Epoxy polyester powder coated thickness of 40 microns . Shelf construction shall be with 12 bend panel made from CRCA steel 0.7 mm thick IS:513, Gr.D .Uniformly distributed load capacity of 100 Kg . Undercarriage shall have construction in welded frame made of HR sheet 3 mm thick conforming to IS : 2062. The Movements shall be Drive Type configuration : In case of D2,D3 & D4 movement of units is achieved mechanically through a PU Hand Wheel and Sprocket-Chain arrangement mounted rigidly onto body size. For D3 each movable undercarriage shall be provided with 3 driving rollers and 3 driven rollers.LD understructure has 2 nos. of anti-tilt bearing assembly.The roller assembly comprises of a die-cast step wheel, 2 deep-groove ball bearings and a MS shaft. The step wheel is made of cast steel and is fitted onto the MS shaft using a feather key. The two ball bearings are then fastened on either side of the step wheel using circlips. This entire roller assembly is then snap-fitted into a wheel housing. The wheel housing is fixed in the U-channel of the understructure using machine screws. This wheel-housing is made of engineering plastic material made by injection-molding process. The entire roller assembly is designed to withstand the maximum loads of the body. Fittings shall be centralized locking arrangement through Lock which is operated by spring mechanism mounted onto understructure of last drive unit. The lock is made of 0.8 mm thick conforming to IS:513..The ‘sprocket-chain’ arrangement is covered by a 1 mm thk. CRCA sheet Drive Unit Cover with dimensions 1202mm x 398mm x 87mm and is fixed onto the side of the body. The PU handwheel is rigidly fixed at suitable height on side of the body & projects out of cover by another 99.0 mm. Last unit (LD) have the Drive Unit Cover. When the last Body is Twin Drive, i.e., TD, hinged doors are provided for the last body. In this scenario the centralized locking system is fitted on the last TD body. Each Drive Type units shall have Locking Knob near the drive wheel for manual locking of individual units when a person is using those units. Knob shall be rotated to unlock position when units are to be moved. End stoppers shall be provided to prevent derailment.The nuts & bolts are galvanized / blackodized / Zn Plated. Also total no. of loading levels per understructure shall be 20 for LD4. Label holder - It is an aluminium extrusion of length 396mm for LD/SD and 796mm for TD, fitted on to front cover of body. The Paper is 300GSM matt milky white sticker paper, to be inserted into the aluminium extrusion. The length of paper is 394mm for LD/SD and 794mm for TD. Over that a transparent plastic of corresponding length of 150-200 micron polythene is to be inserted. This product should be certified By GRIHA & SVAGRIHA , GREEN PRO, GREENGUARD, Indoor Advantage GOLD Providing, suplying and placing of stoarge unit.Overall Dimensions of TD 4 Single Drive Cover Unit 4 Bay(U/C + Fittings + Cover) shall be 4800mm(W) x 800mm(D) x 2113mm(H). The Construction shall be rigid knock down made out of 0.8 thick CRCA steel conforming to IS:513, Gr.D. Each body shall have 1 main unit plus add on units (0,1,2,3 depending on no. of bays 1, 2, 3, 4 respectively) . Finish shall be Epoxy polyester powder coated thickness of 40 microns . Shelf construction shall be with 12 bend panel made from CRCA steel 0.7 mm thick IS:513, Gr.D .Uniformly distributed load capacity of 100 Kg . Undercarriage shall have construction in welded frame made of HR sheet 3 mm thick conforming to IS : 2062. The Movements shall be Drive Type configuration : In case of D2,D3 & D4 movement of units is achieved mechanically through a PU Hand Wheel and Sprocket-Chain arrangement mounted rigidly onto body size. For D3 each movable undercarriage shall be provided with 3 driving rollers and 3 driven rollers.LD understructure has 2 nos. of anti-tilt bearing assembly.The roller assembly comprises of a die-cast step wheel, 2 deep-groove ball bearings and a MS shaft. The step wheel is made of cast steel and is fitted onto the MS shaft using a feather key. The two ball bearings are then fastened on either side of the step wheel using circlips. This entire roller assembly is then snap-fitted into a wheel housing. The wheel housing is fixed in the U-channel of the understructure using machine screws. This wheel-housing is made of engineering plastic material made by injection-molding process. The entire roller assembly is designed to withstand the maximum loads of the body. Fittings shall be centralized locking arrangement through Lock which is operated by spring mechanism mounted onto understructure of last drive unit. The lock is made of 0.8 mm thick conforming to IS:513..The ‘sprocket-chain’ arrangement is covered by a 1 mm thk. CRCA sheet Drive Unit Cover with dimensions 1202mm x 398mm x 87mm and is fixed onto the side of the body. The PU handwheel is rigidly fixed at suitable height on side of the body & projects out of cover by another 99.0 mm. When the last Body is Twin Drive, i.e., TD, hinged doors are provided for the last body. In this scenario the centralized locking system is fitted on the last TD body. Each Drive Type units shall have Locking Knob near the drive wheel for manual locking of individual units when a person is using those units. Knob shall be rotated to unlock position when units are to be moved. End stoppers shall be provided to prevent derailment.The nuts & bolts are galvanized / blackodized / Zn Plated. Also total no. of loading levels per understructure shall be 40 for TD4. Label holder - It is an aluminium extrusion of length 396mm for LD/SD and 796mm for TD, fitted on to front cover of body. The Paper is 300GSM matt milky white sticker paper, to be inserted into the aluminium extrusion. The length of paper is 394mm for LD/SD and 794mm for TD. Over that a transparent plastic of corresponding length of 150-200 micron polythene is to be inserted.CRCA Steel conforming to IS: 513 Gr.D. This assembly is available for both heights – 1980H and 2361H. This product should be certified By GRIHA & SVAGRIHA , GREEN PRO, GREENGUARD, Indoor Advantage GOLD It consists of ‘C’ section 2 mm thk HR sheet & Square 25.4mm X 2mm thk ERW tube – both connected by screws. Prior to the grouting of the guide channels with the help of raul plug & screw, ensure the ground is level. The rail channels are of 3 lengths i.e., 800mm, 1600mm and 2400mm.

Sofa 1 Seater Type II :- Providing, supplying and placing Pisa one seater sofa. SEAT FOAM : The seat is made up of PU foam in Density 28 ±2 kg/cu.mtr with an additional top layer of supersoft PU foam in Density 32 ± 2 kg/cu, upholstered with fabric or leatherette. BACK FOAM : The back is made up of PU foam in Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. UNDERSTRUCTRE : Understructure is made up of 1.2±0.1 cm. thick hot pressed plywood [moisture resistance & termite proof as per IS:303] & pinewood of cross sections devoid of major knots & surface defects. 6 nos. per seat & 3.8mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose. LEG ASSEMBLY : It is a welded Assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap. Width (W): 86.0 CM. Depth (D): 90.5 CM. Height (H): 85.5 CM. Seat Height (SH): 45.0 CM.

Sofa 3 Seater Type II :- Providing, supplying and placing Pisa three seater sofa. SEAT FOAM : The seat is made up of PU foam in Density 28 ±2 kg/cu.mtr with an additional top layer of supersoft PU foam in Density 32 ± 2 kg/cu, upholstered with fabric or leatherette. BACK FOAM : The back is made up of PU foam in Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. UNDERSTRUCTRE : Understructure is made up of 1.2±0.1 cm. thick hot pressed plywood [moisture resistance & termite proof as per IS:303] & pinewood of cross sections devoid of major knots & surface defects. 6 nos. per seat & 3.8mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose. LEG ASSEMBLY : It is a welded Assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap. Width (W): 206.0 CM. Depth (D): 90.5 CM. Height (H): 85.5 CM. Seat Height (SH): 45.0 CM.

Side Table :- Providing, supplying and placing Pisa side table. SIDE TABLE GLASS: It is 10 ±0.3 mm thick black tinted Toughened glass UV glued with bushes made in SS 202 grade for focing with understructure. SIDE TABLE UNDERSTRUCTURE: It is a welded Assembly made in SS202 grade Dia. 12±0.04 as per IS:1762. Width of table= 60.0 cm, Depth=60.0 cm, height=34.9 cm.

Reception Desk Type I :- Providing & supplying on site as per Sample Approved by Architect and as per the instructions of The Engineer In Charge

Reception Desk Type II :- Supplying and placing in position Reflection Linear Desk 5 ft Reception table of the following specifications. Work Surface - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Access Flap provided on work surface for wire management. Wire Management - Power box made with 0.8 mm thick CRCA (IS: 513), with switch plate (8+3 Module cut out provision for Anchor Roma). This is fixed with worktop along the width at Access Flap position. Modesty Panel & Side Skirting - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Understructure - Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. TOP shelf - Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Hinge Door + Drawer unit - Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. **Drawer bottom is made of 5.5thk MDF whiteboard Handle is provided for ease of opening. HDU and Drawer is provided with cam lock for security. Essential Accessories - Wire Riser made of 0.8mm CRCA (IS-513) is provided for proper wire management. Organizer Plate made of 1.2mm CRCA (IS-513) is provided for magnetic sticky notes. Bag Hanger Hook made of 1.2mm CRCA (IS-513) is provided for bag hanging. Length - 1500mm, Depth - 870mm, Height - 1080mm

Sofa two seater:- Providing & supplying Rewind Sofa Dimensions W x H x D (cm)-127.5 x 83.5 x 80 Upholstery•Material : Syn Leather •Shade: Crush Brown •Thickness: 1 mm Frame :•Material : Pine Wood •Moisture content : 1012% •Thickness of Plywood used : 12 mm & 18 mmSeat Foam : •Material : Slab stock •Density : 32 kg/m3 at seat Back Foam : •Material : Slab stock •Density : 28 kg/m3 at seat Webbing :•Material : Nylon Legs :•Material : PVC

Sofa 3 Seater:- Providing & supplying Rewind Sofa Dimensions W x H x D (cm)-175.0 x 83.5 x 80 Upholstery•Material : Syn Leather •Shade: Crush Brown •Thickness: 1 mm Frame :•Material : Pine Wood •Moisture content : 1012 % •Thickness of Plywood used : 12 mm & 18 mm Seat Foam : •Material : Slab stock•Density : 32 kg/m3 at seat Back Foam :•Material : Slab stock •Density : 28 kg/m3 at seat Webbing : •Material : Nylon Legs :•Material : PVC

Visitor Chair:- Providing & supplying Sally Midback Chair SEAT ASSEMBLY: The seat is made up of 1.5 ± 0.1 cm thick hot - pressed plywood upholstered with fabric and moulded polyurethane foam. SEAT ASSEMBLY: 47.00CM (W) X 45.70CM(D) BACK ASSEMBLY: The Back is injection molded in Glass filled Polypropylene which is upholstered with Mesh fabric.The back is connected to tabular frame structure. BACK SIZE: 48.00 cm(W) x 57.60 cm(H). POLYURETHANE FOAM: The polyurethane foam for seat is of density= 48 ± 3kg/m. ARMs(FIXED): The arm is made of injection molded in Glass filled Polypropylene which is connection to seat & back together. Caps are provided to hide Armrest tubular frame joinery. TUBULAR FRAME : The powder coated (DFT 40-60 micron) tubular frame is cantilever type & made of Ø2.5±0.03 cm x 0.2±0.016 cm thk MS ERW tube.The Shoe is made of injection molded in Glass filled Polypropylene, fixed on the tubular frame from bottom side. ARMREST SUPPORT : The armrest support is made of injection molded in Glass filled Polypropylene which is fixed to tubular frame. WIDTH (W)54.00 CM DEPTH (D) 64.70 CM HEIGHT (H) 93.30 CM SEAT HEIGHT (SH)45.50 CM

Almirah :- Providing & supplying Storwel plain shall have an overall size of 916mm(W)x486mm(D)x1981mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. The Storwel Plain should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available.

Sofa two Seater Type III :- Providing & supplying Suez 2 Seater sofa Dimensions W x H x D (cm) 108 x 68.50 x 81 Seat Height (cm) - 41.5 Finish Color - Tobac Primary Material - Leatherette Upholstery Material - Synthetic Leather

Sofa three Seater Type III :- Providing & supplying Suez 3 Seater sofa Dimensions W x H x D (cm) 161 x 68.50 x 81 Seat Height (cm) - 41.5 Finish Color - Tobac Primary Material - Leatherette Upholstery Material - Synthetic Leather

Recliner Sofa 2 Seater:- Providing & supplying Sumo 2 SEATER W x H x D (cm) : 157.5 x 102 x 91.5 Seat + Arm-rest : Understructure: Understructure of seat is made up of combination of pinewood members and 12mm thick Plywood. Pinewood are of cross sections 34x49, 34x64, 16x35 and 16x64mm & for seat of Mid-unit 22x40, 22x64, 34x64, 16x35 & 16x64mm without having major knots & defects on the surface. Understructure of Arm-rest is made up of combination of pinewood members and 12mm thick Plywood. Pinewood are of cross sections 40x40 and 22x40mm without having major knots & defects on the surface. Complete understructure of Seat and Arm-rest is made by gluing, nailing & stapling. · Foam: Seating surface is made by using pocket spring of wire dia 2mm which is surrounded by PU foam of density 28 kg/m 3. A top layer of supersoft PU foam with density 32 kg/m3 is used to provide softness.PU foam with density 60 kg/m3 is glued to the front side and back side. Armrest is surrounded by PU foam of density 60 kg/m3 on the out side and 32 kg/m3 on the top. Back-rest : · Understructure: Understructure is made up of combination of pinewood members, 12mm THK Plywood . Pinewood are of cross sections 35x16, 40x22 & 50x16mm and & for tilt back-rest of Mid-unit 16x35 & 50x16mm without having major knots & defects on the surface. · Foam: Backrest is made of PU foam with density 60 kg/m3 that including back side, both LH & RH side & upper side. Cushions for backrest: Cushion is made up of loose recron filled in White non-woven bag. This stitched non-woven bag is kept inside the upholstery cover of cushion pillow. 4. Upholstery: A] Complete body is upholstered with woven fabric [ ALNO] which is having following colour options: Scheme 1: K - 159 - 22 (F1) & K - 159- 17 (F2), Scheme 2 : K - 159 - 22 (F1) & K - 159 - 12 (F2) Reclining Mechanism:The mechanism is from No. It is made up of mild steel linkages which are riveted together. The reclining mechanism is tested for 158 kg load. Bushes: Plastic bushes are fitted at the bottom surface of the reclining mechanism and the connecting rail. Assembly: The upholstered back assembly is fixed with the upholstered combined seat-armrest assembly with the help of sliding brackets. Packet: Each packet contains one upholstered Sofa SKU with reclining mechanism for 1S/2S/3S and connecting rail for 2S/3S

Recliner Sofa 3 Seater :- Providing & supplying Sumo 3 seater sofa 3 SEATER W x H x D (cm) : 214 x 102 x 91.5. Seat + Arm-rest : Understructure: Understructure of seat is made up of combination of pinewood members and 12mm thick Plywood. Pinewood are of cross sections 34x49, 34x64, 16x35 and 16x64mm & for seat of Mid-unit 22x40, 22x64, 34x64, 16x35 & 16x64mm without having major knots & defects on the surface. Understructure of Arm-rest is made up of combination of pinewood members and 12mm thick Plywood. Pinewood are of cross sections 40x40 and 22x40mm without having major knots & defects on the surface. Complete understructure of Seat and Arm-rest is made by gluing, nailing & stapling. · Foam: Seating surface is made by using pocket spring of wire dia 2mm which is surrounded by PU foam of density 28 kg/m. 3. A top layer of supersoft PU foam with density 32 kg/m3 is used to provide softness.PU foam with density 60 kg/m3 is glued to the front side and back side. Armrest is surrounded by PU foam of density 60 kg/m3 on the out side and 32 kg/m3 on the top. Back-rest : · Understructure: Understructure is made up of combination of pinewood members, 12mm THK Plywood . Pinewood are of cross sections 35x16, 40x22 & 50x16mm and & for tilt back-rest of Mid-unit 16x35 & 50x16mm without having major knots & defects on the surface. · Foam: Backrest is made of PU foam with density 60 kg/m3 that including back side, both LH & RH side & upper side. Cushions for backrest: Cushion is made up of loose recron filled in White non-woven bag. This stitched non-woven bag is kept inside the upholstery cover of cushion pillow. 4. Upholstery: A] Complete body is upholstered with woven fabric [ ALNO] which is having following colour options: Scheme 1: K - 159 - 22 (F1) & K - 159- 17 (F2), Scheme 2 : K - 159 - 22 (F1) & K - 159 - 12 (F2) Reclining Mechanism:The mechanism is from No. It is made up of mild steel linkages which are riveted together. The reclining mechanism is tested for 158 kg load. Bushes: Plastic bushes are fitted at the bottom surface of the reclining mechanism and the connecting rail. Assembly: The upholstered back assembly is fixed with the upholstered combined seat-armrest assembly with the help of sliding brackets. Packet: Each packet contains one upholstered Sofa SKU with reclining mechanism for 1S/2S/3S and connecting rail for 2S/3S

Highback Chair Type II: Providing, supplying and placing Thrill Executive High Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area.The Recron filling done in seat & back ( Executive chairs only) for extra fluffiness and comfort in chair. The chair seat & back size are: HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H), SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression, ARMRESTS : The 3-way adjustable armrest is is made of die-cast aluminium with buffing finish designed with the following features : · Up-Down adjustment–7 steps (7.0 ± 0.5cm range) · It has to & fro movement along with Swivel adjustment. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: 360° revolving type, 3 position locking with anti shock mechanism, Tilt tension adjustment. PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm. PEDESTAL ASSEMBLY : The pedestal is made of die-cast aluminium with buffing finish. It is fitted with 5nos. twin wheel castor. The pedestal is 67.0 ± 0.5cm pitch-center dia. (77.0 ± 1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 77.0 CM, DEPTH (D): 77.0 CM, HEIGHT (H): 110.5-120.5 CM, SEAT HEIGHT (SH): 44.5-54.5 CM.

Meshback Chair:- Providing & supplying Thrill Meshback Chair SEAT/BACK ASSEMBLY: The seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The seat has extra thick foam on front edge to give comfort to popliteal area. The Back is injection moulded in glass filled Polypropylene which is upholstered with Mesh fabric.The back consist of adjustable lumbar support made of injection moulded Polypropylene having an adjustment of 5.0 ±0.1 cm. The chair seat & back size are SEAT SIZE 53.5 cm. (W) x 51.0 cm.(D) *MESH BACK SIZE51.0 cm. (W) x 70.0 cm. (H). HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane seat foam is moulded with density 45±2 kg/m³ and hardness 14±2 kgf as per IS:7888 for 25% compression. ARMRESTS :The adjustable armrest is designed with the following features : · Up-Down adjustment– 6 steps (7.2 ± 0.5cm range) · Armrest top is mounted on Armrest structure made of glass filled Nylon · Fixed Armrest Top is PU moulded over Polypropylene insert. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: 360° revolving type. · 3 position locking with anti shock mechanism. · Tilt tension adjustment. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment with an adjustment stroke of 9.5 ± 0.3cm. PEDESTAL ASSEMBLY : The pedestal is injection moulded in black glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.1 ±0.5cm. pitch-center dia. (76.1 ±1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon.WIDTH (W): 76.1 CM. DEPTH (D): 76.1 CM. HEIGHT (H): 101.5 - 111 .5CM. SEAT HEIGHT (SH): 46.0 - 56.0 CM

Back Credenza 1.65 x 0.75 m:- Providing & supplying Topaz Back unit Overall Dimension - 1650x500x750 Top Panel:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Slide Door Unit:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shad confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping for body panels like side, bottom,back and shelves.Shutters are made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Shutters have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Storage is provided with lock for security.

Office Tables 1.8 x 0.75 m:- Providing & supplying Topaz Back Unit Overall Dimension - 1800x500x750. Top Panel:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Slide Door Unit:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shad confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping for body panels like side, bottom,back and shelves.Shutters are made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Shutters have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Storage is provided with lock for security.

Office Tables 2.35 x 0.75 m:- Providing & supplying Topaz Back Unit Overall Dimension - 2350x500x750 Top Panel:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Slide Door Unit:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shad confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping for body panels like side, bottom,back and shelves.Shutters are made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Shutters have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Storage is provided with lock for security.

Office Tables 1.35 x 0.75 m :- Providing & supplying Topaz table with Overall Dimension - 1350x600x750 Work Surface:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Gromet provided on work surface for wire management Modesty Panel:Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Under- structure:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Hinge Door Storage:Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Handle is provided for ease of opening. Storage is provided with lock for security.

Office Table with Side Unit :- Providing & supplying Topaz Table with Side Unit Supplying and placing in position Godrej Make Main Table,ERU & pedestal of the following specifications. Overall Dimension - 2100x2250x750 Primary Work Surface:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Softclosing access flap with in-build power box are provided on work surface for wire management. Secondary Work Surface:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Modesty Panel:Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Under- structure:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Integrated Pedestal:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedstal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestal is provided with lock for security. This product should be certified by GREENGUARD, Indoor Advantage GOLD & GREEN PRO.

Office Tbale 1.35 x 0.6 m:- Providing & supplying Topaz Table Supplying and placing in position Godrej Make Main table of the following specifications.Overall Dimension - 1350x600x750 Work Surface:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Gromet provided on work surface for wire management. Modesty Panel:Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Under- structure:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Hinge Door Storage:Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Handle is provided for ease of opening. Storage is provided with lock for security. This product should be certified by GREENGUARD, Indoor Advantage GOLD & GREEN PRO.

Breakout Table:- Providing & supplying Topo Table Dimensions W x D x H (cm)- 90 X 90 X 72 WORKTOP (PU) Worktop is made of 25mm MDF OSR with pu matt finish on top side. Hardness on top surface is 2H. The worktop is available in 5 shapes; viz.: Circle, Bite, Rectangle, Square & Face UNDER-STRUCTURE: The under-structure consists of an InnerTube Assembly with Top Plate, for Worktop Mounting, & an Outer Tube Assembly with Round/Rectangle/Square Bottom Plate. The Inner & Outer Tube Assemblies are telescopically connected. The Top Plate is made of 5mm thk HOT ROLLED Steel Plates (HR) (As per IS:2062) & the bottom plate is made of 8mm thk HOT ROLLED Steel Plates (HR) (As per IS:2062). The Inner Tube Assembly is made of 082.5 x 2thk ROUND ELECTRIC RESISTANCE WELDED Tubes (ERW)(As per IS:7138) and 8mm thk HOT ROLLED Steel Plates (HR) (As per IS:2062) welded together using TUNGSTEN INERT GAS Welding. The Outer Tube Assembly is made of 089 x 2.5 thk and ROUND ELECTRIC RESISTANCE WELDED Tubes (ERW)(As per IS:7138) and 8mm thk HOT ROLLED Steel Plates (HR) (As per IS:2062) welded together using TUNGSTEN INERT GAS Welding. The whole structure is EPDXY POLYESTER Powder Coated (DFT 40-60 microns). The product has a knock-down construction. It is assembled using alloy steel hardware (blackened & coated with rust preventive oil).

Training Room Chairs:- Providing, supplying and placing Unwind chair with desklet.The Seat and Back should be made up of injection moulded indoor grade PolyPropylene compound. SEAT SIZE : 52.5 cm. (W) x 53.2 cm. (D) BACK SIZE : 51.6 cm. (W) x 40.5 cm. (H). The powder coated ( DFT 50±10 microns ) welded tubular frame should be made from 0 2.22 ± 0.03 cm x 0.16 ± 0.0128 cm and 3.5 ± 0.03 cm x 1.5 ± 0.03 cm x 0.16 ± 0.0128 cm MSERW tube. The shoes should be made of indoor grade PolyPropylene compound and snap fitted with tubular frame. The Armrest should be made of indoor grade PolyPropylene compound and assembled over the tubular frame. The "L" shaped desklet should be made of 1.8+-0.05cm thick prelaminated particle board with 0.2+-0.05cm thick injection moulded poly proplylene all around. Desklet should have back and front adjustment of 4.4+-0.5cm. The paper tray should be made of 0.4mm thick MS rod which is spot welded to form a mesh like structure. Overall Dimensions of Chair Seat Height - 45.0 cm. Height - 84.5cm. Width-57.5 cm and Depth-67.8 cm. This product should be certified by Indoor Advantage GOLD, GREENGUARD GOLD, GRIHA & SVAGRIHA & GREEN PRO.

Computer Tables 1.35 x 0.6 m:- Providing & supplying Upbeat Modular desk based system of ht. 1200 mm. Overall size 1350 x 600 with slanted angle as per the drawing approved by architect. Swing legs a PDC (Swing leg corner PDC) part made from Aluminum alloy, which is connected to the worktop and cross members.. Swing leg can be offer in dual color. Wire Management Single Power box with raiser for Manager Modules, Single tables (8+3 Anchor Roma). Soft closing access flap with brush. Metal modesty: Metal modesty is made from 0.8 mm thick CRCA. Metal modesty are mounted on the worktop with the help of the modesty mounting brackets made of 3 mm thick HR. Worktop: 25mm thk prelaminated partical board with pvc lipping. CUSTOMISED PARTITIONS: As per the approved shop drawing and design required. Material construction in 25mm thick plywood both side laminated..

Computer Tables 1.5 x 0.75 m :- Providing & supplying Upbeat #Modular desk based system of ht. 1200 mm. Overall size 1500 x 750 with slanted angle as per the drawing approved by architect. Swing legs a PDC (Swing leg corner PDC) part made from Aluminum alloy, which is connected to the worktop and cross members.. Swing leg can be offer in dual color. Wire Management Single Power box with raiser for Manager Modules, Single tables (8+3 Anchor Roma). Soft closing access flap with brush. Metal modesty: Metal modesty is made from 0.8 mm thick CRCA. Metal modesty are mounted on the worktop with the help of the modesty mounting brackets made of 3 mm thick HR. Worktop: 25mm thk prelaminated partical board with pvc lipping. CUSTOMISED PARTITIONS: As per the approved shop drawing and design required. Material construction in 25mm thick plywood both side laminated..

Workstations 1.65 x 0.75 m with customised partitions:-Providing & supplying Upbeat#Modular desk based system of ht. 1200 mm. Overall size 1650 x 750 with slanted angle as per the drawing approved by architect. Swing legs a PDC (Swing leg corner PDC) part made from Aluminum alloy, which is connected to the worktop and cross members. Swing leg can be offer in dual color. Wire Management Single Power box with raiser for Manager Modules, Single tables (8+3 Anchor Roma). Soft closing access flap with brush. Metal modesty: Metal modesty is made from 0.8 mm thick CRCA. Metal modesty are mounted on the worktop with the help of the modesty mounting brackets made of 3 mm thick HR. Worktop: 25mm thk prelaminated partical board with pvc lipping. CUSTOMISED PARTITIONS: As per the approved shop drawing and design required. Material construction in 25mm thick plywood both side laminated..

Computer Tables 0.9 x 0.6 m Type I:- Providing & supplying Upbeat #Modular desk based system of ht. 1200 mm. Overall size 900x600 as per the drawing approved by architect. Swing legs a PDC (Swing leg corner PDC) part made from Aluminum alloy, which is connected to the worktop and cross members. Swing leg can be offer in dual color. Wire Management Single Power box with raiser for Manager Modules, Single tables (8+3 Anchor Roma). Soft closing access flap with brush. Metal modesty: Metal modesty is made from 0.8 mm thick CRCA. Metal modesty are mounted on the worktop with the help of the modesty mounting brackets made of 3 mm thick HR. Worktop: 25mm thk prelaminated partical board with pvc lipping.

Computer Tables 1.2 x 0.6 m:- Providing & supplying Upbeat #Modular desk based system of ht. 1200 mm. Overall size 1200 x 600 with slanted angle as per the drawing approved by architect. Swing legs a PDC (Swing leg corner PDC) part made from Aluminum alloy, which is connected to the worktop and cross members.. Swing leg can be offer in dual color. Wire Management Single Power box with raiser for Manager Modules, Single tables (8+3 Anchor Roma). Soft closing access flap with brush.Metal modesty: Metal modesty is made from 0.8 mm thick CRCA. Metal modesty are mounted on the worktop with the help of the modesty mounting brackets made of 3 mm thick HR. Worktop: 25mm thk prelaminated partical board with pvc lipping. CUSTOMISED PARTITIONS: As per the approved shop drawing and design required. Material construction in 25mm thick plywood both side laminated..

Computer Tables 0.9 x 0.6 m Type II :- Providing & supplying Upbeat #Modular desk based system of ht. 1200 mm. Overall size 900 x 600 with slanted angle as per the drawing approved by architect. Swing legs a PDC (Swing leg corner PDC) part made from Aluminum alloy, which is connected to the worktop and cross members. Swing leg can be offer in dual color. Wire Management Single Power box with raiser for Manager Modules, Single tables (8+3 Anchor Roma). Soft closing access flap with brush. Metal modesty: Metal modesty is made from 0.8 mm thick CRCA. Metal modesty are mounted on the worktop with the help of the modesty mounting brackets made of 3 mm thick HR. Worktop: 25mm thk prelaminated partical board with pvc lipping. CUSTOMISED PARTITIONS: As per the approved shop drawing and design required. Material construction in 25mm thick plywood both side laminated..

File Storage:- Providing & supplying VSDU - 12. Overall Dimensions of VSDU - 12 shall be 1200mm(W)x450mm(D)x1192.5mm(H) . The top shall be wooden top PLB(25 mm add in unit height ) . The Rigid Knock Down Construction , Back , Sides and Door shall be made from 0.7 mm high yield strength CRCA ,rest in 0.8 mm CRCA . CRCA - 'D' Grade as per IS-513 . Sliding door arrangement shall have sliding door wth top hanging arrangement to prevent derailment . Each door shall be provided with 2 plastic roller having steel ball bearing for smooth movement of door & less noise . Locking shall be 5 lever cam lock for safe locking . Handle shall be plastic flush & recessed handle . Shelving shall have Height wise adjustable shelf mounting . Uniformly Distributed Load Capacity of the shelf is 40 Kg maximum . VSDU - 12 shall have 4 no. of adjustable half shelves . Accessories optional shall be cradle with pipes for hanging godrej instadex files . Leveler shall be screw type leveler with hex plastic base and overall finish shall be epoxy polyester coated to the thickness of 50 microns . For VSDU 12 - A4 size box file can be stored vertically on two shelves and clear space above third shelf is 295 mm .

Workstations 1.5 x 0.6 m Type II :- Providing & supplying Wish System Tables SIZE: MAIN TABLE - 1500 x 600 + ERU - 900 W (1 PERSON) * PROVIDING AND FIXING 52.4MM THICK 1200 MM HIGH PANELS IN WISH SYSTEM. WITH COMBINATION OF METAL RACEWAY AT BOTTOM, TWO INTERMEDIATE FABRIC BLOCKS, FABRIC TACKABLE, WHITE BOARD, FABRIC MAGNETIC AT TOP. PROVIDING POWDER COATED LEGS..* PROVIDING POWDER COATED FRONTIER LEGS & PRELAM MODESTY

Workstations 1.2 x 0.6 m Type II :- Providing & supplying Wish System Tables SIZE: 1200 x 600 * PROVIDING AND FIXING 52.4MM THICK 1200 MM HIGH PANELS IN WISH SYSTEM. WITH COMBINATION OF METAL RACEWAY AT BOTTOM, TWO INTERMEDIATE FABRIC BLOCKS, FABRIC TACKABLE, WHITE BOARD, FABRIC MAGNETIC AT TOP. PROVIDING POWDER COATED LEGS..* PROVIDING POWDER COATED FRONTIER LEGS & PRELAM MODESTY

Workstations 1.2 x 0.6 m :- Providing & supplying Wish System Tables SIZE: 1200 x 600 * PROVIDING AND FIXING 52.4MM THICK 1200 MM HIGH PANELS IN WISH SYSTEM. WITH COMBINATION OF METAL RACEWAY AT BOTTOM, TWO INTERMEDIATE FABRIC BLOCKS, FABRIC TACKABLE, WHITE BOARD, FABRIC MAGNETIC AT TOP. PROVIDING POWDER COATED LEGS..* PROVIDING POWDER COATED FRONTIER LEGS & PRELAM MODESTY

Workstations 0.9 x 0.6 m :- Providing & supplying Wish System RECTA WORKSTATIONS - 900W x 600D Providing and placing WISH panel based modular workstation, with partition thickness as 52.4 mm thk and ht - 1200 including powder coated aluminium trims. FIN: out of 22.5 mm thk panel formed out of blocks which are 18 mm thk PLB boards. Top block finished in fabric. Bottom block is finished in metal. HALF SCREEN: out of 22.5 mm thk screen formed out of blocks which are 18 mm thk PLB boards. Screen finished in fabric tackable. Tiles: Combination of top tiles are fabric tackable and white board. Bottom tiles - Plain metal. Wire Management - Wires shall be taken into the system through cable ducts from the junction boxes and it is carried upto the panels through concealed conduits inside the blocks. legs - metal powder coated legs at the shared condition. System shall also have 120 mm high powder coated standalone panel legs to give the system an elevated look. Worksurface - out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 900W x 600D / 1050W x 600D / 1200W x 600D   Note: All partitions and side panels have levelling screws for adjustment in case of Uneven floor to take care of +/- 10-15 mm of uneven flooring

Library Book Rack With Stand IVAR model bookshelf of real wood for accomodating books, small accessories & show pieces comes in complete knockdown state contain 4 shelf with 5 partion Size:- 880Wx355 Dx 1600H in mm. and Stand for bookshelf with metal or wooden box size of 920mmWx400mmDx450H.