Skill Development And Entrepreneurship Department Tender

43.2 Size: 100 mm 43.3 3-way ratchet for use in confined spaces 43.4 Made of Chromium plated metal parts 43.5 Corrosion resistant 43.6 Bit Brace with 12 point 43.7 3-way ratchet for use in confined spaces

56.2 Size – 250 mm 56.3 Used to remove heated solder from a PCB 56.4 Should be made from high grade aluminum for light weight and airtight function Tip 56.5 should be made of high temperature resistant Teflon

22.2 GenerallyconformtoIS844 -1979 22.3 Dimensions in mm (+/-5%):A-100,D-6 22.4 Blade: 22.4.1 Blade made of high grade Silicon –Manganese Steel 22.4.2 Material of Blade EN 45A 22.4.3 Bladeshouldbedifferentiallyhardened&temperedtoresistwear,bending &meet high torque requirement 22.4.4 HardnessonTip:55 -58HRC 22.4.5 BrightandSmoothNickelChromeplatingfinishtoeffectivelyprotectbladea gainst corrosion 22.4.6 Tip should be formed by Forging &Trimming 22.4.7 Tipsides&facesshouldbewellgroundwithgoodfinish.Doubleearcoiningsh ouldbe provided for the blade. 22.5 Handle: 22.5.1 Material of Handle: Cellulose Acetate 22.5.2 HandleshouldbemadeofhighgradeCelluloseAcetatePlastic,whichisnonflammable&unaffectedbyoil, petrol, grease, water -practically anything 22.5.3 Handle should with stand rough use including hammering 22.5.4 Handledesignshouldbesuchthatitgivescomfortablegripevenathighertor ques 22.5.5 Handle blade assembly should be insert molded

30.2Dimensions 30.2.1 Total Length: 325mm ±3mm 30.2.2 Max. Width.: 128 ±1mm 30.2.3 Min. Width: 112 ±1 mm 30.2.4 Thickness: 60mm±1mm 30.3 Wood material: Hard Wood 30.4 Handle gripis secured by along taper 30.5 Should be light weight for fine working 30.6 Finishing: Fine finishing with body or chamfered. 30.7 Should easy to operate for operate or during hammering

Branded ISI Mark

44.2 Faster drilling - up to 4 times faster than standard HSS-R drill bits 44.3Increased durability - up to 50% stronger than standard HSS-R drill bits 44.4Cleaner, accurate, burr-free holes due to recessed cutting wings 44.5Permanent size markings located above shank for increased visibility 44.6 Size - 2 mm, 5 mm and 6 mm set of 3

ISI Marked Branded

ISI mark Branded

 Range: Centre Zero, 100 - 0 - 100 mV, Analog  Type: MovingCoilDC- Analog  Input: 100mV  Accuracy: Class 1.5  Shouldhavelinearscale  Should be easily replaceable glass and bezelScale  shouldhaveinterchangeability  Shouldbeeasy installationwith swivelscrews  Should have Glass filled polycarbonate housing (UL 94-V-0) Knife edge pointer.  Selfliftingterminalclampassembly  IP52protection  Wide measurement band - 10 to 100% of FSD  Movement o Movingcoilmovementshouldhavepivotsofveryhighhardness. o MovementshouldhavesuspendedbetweenspringloadedSapphireJewels. o Movementshouldhaveproperlyshielded&criticallydampedbyeddycurrent s induced incoilformer.  Reference Standards o PerformanceStandard: IEC 60051&IS1248 o Safetystandard: IEC61010 o Nominalcaseandcutout dimensions: IS2419&DIN43700 o Scale andPointer: DIN43802 o ConnectionandTerminalmarkings: DIN43807 o Terminalbolts/leads: DIN46200/46282 o Safetyrequirementsandprotectivemeasures: IS9249-1979 o Frontframesdimensions: DIN43718 o Environmentalconditionsspecifications: IS 9000 part 5, 7, 8  Certifications o ERDATypetested o CECertified o UL Approved o RoHScomplied

71.2 Spark Length – 10 mm -75 mm (Adjustable) 71.3Product Type: Corrugated box 71.4Spark Length are Workable - 4-6 volts and rest on 6-12 volts DC 71.5cabinet polish wooden box. 71.6Coils are made from best quality enameled copper wire and paraffin insulation is provided throughout 71.7Fitted with platinum contact with removable spark discharger. 71.8Complete with ON/OFF switch of primary and two Bakelite look type terminals.

46.2 Generally conforming to IS 15385 - 200321.3Length:200mm+/-5%) 46.3 Blade Width: 50mm (+/ -5%) 46.4 Material: Investment& SeasonalFine GreyIronCasting 46.5 Blade material: High carbon Tool Steel(induction hardened) 46.6 Adjustment Screw &Nut Material: Brass 46.7 Brass nut to make the operation of removing tight blades very easy 46.8 MouthWidth:Morethan6mmfor easy flow of chips/dust during operation 46.8.1 Finish:Powdercoatedonungroundedareaandrustpreventiveoilatgrounded area

45.2 Generally conforming to IS 15385 - 200321.3Length: 200mm+/-5%) 45.3 Blade Width: 50mm (+/ -5%) 45.4 Material: Investment& Seasonal Fine Grey Iron Casting 45.5 Blade material :High carbon Tool Steel(induction hardened) 45.6 Adjustment Screw &Nut Material: Brass 45.7 Brass nut to make the operation of removing tight blades very easy 45.8 MouthWidth:Morethan6mmfor easy flow of chips/dust during operation 45.9 Finish:Powdercoatedonungroundedareaandrustpreventiveoilatgroundedarea

ISI mark Anchor

106.2 Type of Product : Digital Flux Meter 106.3 Range: 0-500 tesla 106.4 Accuracy: ±4% rdg + 5 dgts 106.5 Accuracy: ±5% rdg + 8 dgts 106.6 Accuracy: 0.5s 106.7 MAX/MIN Indication Should Be Available 106.8 Data Hold Indication Should Be Available 106.9 Auto Power Off: Should Be Available 106.10 LCD Backlight: Should Be Available 106.11 Low Battery Indication: Should Be Available 106.12 Drop Test: 1m Height 106.13 Sensor Type: Silicon Photocell 106.14 Battery: 4.5 V 106.15 Safety Compliance: EN 61326 - 1 106.16 Pollution Level: 2 106.17 Current Consumption: 106.18 Working: ≤30mA 106.19 Power off: ≤10uA 106.20 Working Environment: Temperature: 0～40˚C 106.21 Humidity: ≤80%RH 106.22 Accessories 106.22.1 Operating Manual 106.22.2 Calibration Certificate 106.22.3 Required Batteries 106.22.4 Plastic or Wooden Carrying Case with required cushioning

ISI Mark Branded

27.2 Material: Stainless Steel 27.3 Should be suitable for right hand use 27.4 Should be suitable for Electrical work Purpose 27.5 Size: 150 mm (± 10%) 27.6 Handle should be covered with a layer of insulated material 27.7 Working Part Hardened to 52-56 HRC

94B.2 Type :- Shunt Type 94B.3 Range :- 50/2000-ohm 94B.4 Should be useful for measuring the resistance value 94B.5 The indicating instrument should be 100 mm rectangular 94B.6 Moving Coil D.C. Meter. 94B.7 Accuracy: ±5% of indicated value.

ISI Mark Branded

ISI Mark Branded

ISI Mark Branded

160.2 Capacity 35 to 40 Stator Per Day 160.3 Counter Type 3 Digit FRD 160.4 Stator Diameter 105mm to 165mm 160.5 Frequency 50 Hz 160.6 Wire Gage 30 to 40 160.7 Winding Direction Clockwise 160.8 Phase Single with speed control 160.9 Motor 1/4 H.P. Single Phase 220v.AC 160.10 Power Supply 220v.AC 160.11 Machine Type Automatic 160.12 Dimensions 810mm x 280mm x 1500mm 160.13 Standard accessories 160.13.1 • all Standard Dies and stand 160.13.2 • Wire guides 160.13.3 • Wire cut sensor 160.13.4 • Spool container with tensioner mounting stand 160.14. INSTRUCTIONS : 160.14.1) OPERATING MANUAL WITH CIRCUIT DIAGRAM MUST BE PROVIDED. 160.14.2) PRACTICALS LIST TO BE PERFORMED SHOULE BE PROVIDED.WITH CIRCUIT DIAGRAM 160.14.3) CONTROL BOARD SHOULD BE FITTED WITH NUT & BOLT PROPERLY AT THE INSTITUTE TO PERFORM PRACTICALS AT MANHEIGHT LEVEL FOR TRAINEE’S SAFTY

67.2 Total Length: 425mm±2mm 67.3 Opening: 6mm 67.4 Material: Cast-iron 67.5 Should have double pinion gear

159.2 With straight and step coil arbors 159.3 Should wind both single and three phase motor coils. . 159.4 for winding motors from 1/2 hp to 40 hp. 159.5 No of arbors - five Step arbors-01 No straight arbors-01 No 159.5.1 Material of arbors Aluminum 159.6 with Manual counter 159.6.1 Count Range: 0-9999 rings 159.7 Size & Material 159.7.1 Size - Base 13" x 15" Package Dimensions: 13 " x 8" x 10" 159.7.2 Material - Mild Steel 159.8 Features: 159.8.1 Easy operations 159.8.2 Easy functioning 159.8.3 Superior performance

(As Per DVET, Maharashtra State SPECIFICATION FOR FURNITURE GROUP ITEMS Version 3 2018- 19 /-S.R. –03 Page No -17

163.2 Specifications: 163.2.1 Type Shaded Pole Motor Fractional H.P 163.2.2 Frequency 50 Hz 163.2.3 Voltage 230-250 V 163.2.4 Number of poles 4 163.2.5 Degree of Protection IP65 163.2.6 Synchronous speed 1500 rpm 163.2.7 Output rating Fractional HP 163.2.8 Mounting Horizontal Footmounted 163.2.9 Terminal box¹ With Terminal Box 163.2.10 Confirming IS : 325 163.2.11 Enclosure IC410 - SPDP

173.2 Specifications 173.3 IS Specifications IS : 2546-1974 173.3.1 Bottom—The bottom shall be dished and shall be joined to the body by butt welding so that there is no raw edge or crevice on the inside of the bucket. The thickness of the bottom sheet shall be 1 mm. 173.3.2 Ears—The ears shall be made of mild steel sheet and shall be fitted to the body at the top by means of welding with the flat head on the side. The thickness of sheet for ears shall be 2·8 mm. 173.3.3Top Handle—The top handle shall be of mild steel rod of 10 mm in diameter with its ends bent up. 173.3.4Bottom Handle—The bottom ‘handle shall be of mild steel rod of 10 mm in diameter and it shall be joined to the bottom by welding as shown in Fig. 1. The grip shall have no sharp edges. 173.4 MARKING AND PACKING 173.4.1 Each bucket shall be stamped or embossed on its side with the manufacturer’s name or trade-mark, year of manufacture and its capacity. Embossing shall be sufficiently deep so that the marking remains quite legible after galvanizing. 173.4.2The product may also be marked with Standard Mark 173.4.3 The use of the Standard Mark is governed by the provisions of the Bureau of Indian Standards Act, 1986 and the Rules and Regulations made thereunder. 173.2.4 Buckets shall be suitably packed 173.2.1 Capacity 5-8 Litre 173.2.2 Body Material Mild steel black sheets used for the manufacture of buckets shall conform to Grade St 34 or Grade St 42 of IS : 1079- 1968†. 173.2.3 Metal Thickness 18 - 20 SWG 173.2.4Colour Red 173.2.5Finishing Paint Coated

69.2 Capacity - 500W to 6 KW 69.3 Type:- heater Type 69.3.1. Load elements shall be Standard, helically wound chromium alloy rated to operate at approximately ½ of maximum continuous rating of wire. Elements must be fully supported across the entire length within the air stream by segmented ceramic insulators on stainless steel rods. Element supports shall be designed to prevent a short circuit to adjacent elements or to ground. 69.3.2. The change in resistance due to temperature shall be minimized by maintaining conservative watt densities. 69.3.3. The overall tolerance of the load bank shall be –0% to +5% kW at rated voltage. A –5%, +5% rating allows the load bank to deliver less than rated kW and shall not be used. The load bank must deliver full rated kW at rated voltage. 69.3.4. The resistors shall not require a cool down period. Failure shutdown of the cooling fan during operation of the resistors shall not shorten their life expectancy. 69.4 Voltage (V) : -240V AC 1 Phase / 415/440V AC, 3 Phase Frequency: -50Hz 69.5 Cooling Fan Required 69.6 Temperature control & Indication Required 69.7 8 No Selector switch Required (4 for - 500W Heater & 4 For 1000W heater ) 69.7.1 Selector switch 1 For - 500 W 69.7.2 Selector switch 2 For - 1000 W 69.7.3 Selector switch 3 For - 500 W 69.7.4 Selector switch 4 For - 1000W 69.7.5 Selector switch 5 For - 500 W 69.7.6 Selector switch 6 For - 1000W 69.7.7 Selector switch 7 For - 500 W 69.7.8 Selector switch 8 For - 1000W 69.8 To provide for major fault protection, branch fuses OR C.B. shall be provided on all three phases 69.9 All electrical circuits shall have a high potential insulation resistance test performed at twice rated voltage plus 1000 VAC to assure insulation integrity.

Specification 154.2 Series Generator Technical Specifications of DC Machine (USED Generator) 154.1.1 Type: Series 154.1.2 Power Rating: 3 H.P. 154.1.3 Voltage Rating: 220V ± 10% 154.1.4 Rated Speed: 1500RPM ± 7.5% 154.1.5 Insulation: Class 'B’ 154.1.6 Confirming To I.S.: 4722-1992 154.1.7 S.P.D.P. Type, Horizontal Foot Mounted 154.1.8 Loading Arrangement: Mechanical, fitted on machine base “C” channel, Durable good quality Spring Balance: 2 Nos. (Tubular Type) with Belt, Brake Drum/Pulley: Aluminum cast with heat suppression Facility 154.1.9 Machine Base: Fabricated MS “C” Channel (75 x 40 x 6 m 154.3 Shunt Generator Technical Specifications of DC Machine (USED Generator) 154.2.1 Type: Shunt 154.2.2 Power Rating: 3 H.P. 154.2.3 Voltage Rating: 220V ± 10% 154.2.4 Rated Speed: 1500RPM ± 7.5% 154.2.5 Insulation: Class 'B’ 154.2.6 Confirming To I.S.: 4722-1992 154.2.7 S.P.D.P. Type, Horizontal Foot Mounted 154.2.8 Loading Arrangement: Mechanical, fitted on machine base “C” channel, Durable good quality Spring Balance: 2 Nos. (Tubular Type) with Belt, Brake Drum/Pulley: Aluminum cast with heat suppression Facility 154.2.9 Machine Base: Fabricated MS “C” Channel (75 x 40 x 6 m 154.4 Compound Generator Technical Specifications of DC Machine (USED Generator) 154.3.1 Type: Compound 154.3.2 Power Rating: 3 H.P. 154.3.3 Voltage Rating: 220V ± 10% 154.3.4 Rated Speed: 1500RPM ± 7.5% 154.3.5 Insulation: Class 'B’ 154.3.6 Confirming To I.S.: 4722-1992 154.3.7 S.P.D.P. Type, Horizontal Foot Mounted 154.3.8 Loading Arrangement: Mechanical, fitted on machine base “C” channel, Durable good quality Spring Balance: 2 Nos. (Tubular Type) with Belt, Brake Drum/Pulley: Aluminum cast with heat suppression Facility 154.3.9 Machine Base: Fabricated MS “C” Channel (75 x 40 x 6 m

70.2 Loading arrangement : Mechanical Brake Test Arrangements 70.3 Spring Balance : 2Nos.(Tubular Type) 70.4 Brake Drum/Pulley : Aluminum casted with heat suppression facility 70.5 Machine Base : “C” Channel Sturdy base frame with heavy duty bolts with C.P handle and also highly accurate dial type spring balance to give proper readings of the machines 70.6 Weight : 0-25 kg 70.3 Made of Chromium plated metal parts 70.4 Should be Corrosion resistant

ELCB and RCCB 25Amps, double pole and 25Amps, double pole, IΔn 30 mA Accessories Items Ver-Ele-01 2021-22

ISI Mark Branded Anchor

ISI mark Anchor

17.1Generally conform to I.S. 841 - 1983 17.2Material Used: Brass & Iron Steel 17.3Additional Name: Brass Pressure Kerosene Blow Lamp 17.4Torch Type Soldering Torch, Brazing Torch 17.5Should be Longer service life Smooth-finish 17.6Should be Resistance against corrosion 17.7Should be Precisely designed 17.8Top quality ,Extremely durable 17.9Capacity: 0.500 ml(± 10 %)

ISI Mark Polycab pure copper

ISI Mark

114.2 Broad, heavily plated brass strips should be mounted on polished hardwood base. 114.3 Terminals with 4 mm sockets should be provided 114.4 24 SWG constantan wire should be stretched along the top of a meter scale in mm and cm 114.5 Should be supplied with JOCKEY 114.6 Dimensions: 1.13 mm X 80 mm X 50 mm (Approx.) 114.7 Two Gap

94A.2 Type :- Series Type 94A.3 Range :- 50/2000-ohm 94A.4 Should be useful for measuring the resistance value 94A.5 The indicating instrument should be 100 mm rectangular 94A.6Accuracy: ±5% of indicated value.

ISI Mark Anchor

9.1 Basic Indicative Diagram 9.2 Blade should be made of high grade Steel for sharp and long cutting 9.3 Hardness: 62 - 64 HRC 9.4 ABS Plastic Body for higher strength & soft material for comfort in use 9.5 Slider locking system for enhanced safety 9.6 Blade Width: 18 mm

1.Input Voltage : 180-240VAC,50Hz 2.Fuse : 3.15A 3.Temperature Control for accurate and precise temperature Digital Display for clear visibility with 7 segment display 4.De-soldering : 24VAC,80W 5.Soldering : 24VAC,70W 6.Desold pump :24VDC, 80W 7.Vacuum Pressure :12000 rpm, 700mm/hg 8.Temp Range : 180 to 480°C 9.Temperature control accuracy +/- 1°C Tip 10.Leakage Current : 2 mA 11.Temperature control Stability +/- 5°C 12.Tip to Ground Resistance : 2 Ohms Tip to Ground Leakage Voltage : 2 mV

161.2 Specification Display Type Digital Accuracy (%) Grater than 1.0Percent (F. S). Supply AC Control With the help of Manual Auto Transformer (according to customer demand) Current Source 10 to 200 Amp (according to customer demand). Condition New Measuring Isolated CT for current output, digital Voltmeter for voltage output Output Power 6.0V (according to customer demand). Up to 15kva Protection a) Overload b) Open circuit c) Over temp. Timer Control Circuit Modes 0.001 to 99999ms, Accuracy 0.1 Percent of reading Plus minus1ms Warranty 1 Year against manufacturing defects & Extended optional. Input voltage Single phase 230V AC, 50Hz Protected with MCB & HRC fuse , or as per customer demand Operation time 1min ON, 5mins OFF. External Current Meter range 100A to 200 A, Accuracy 1 Percent of reading, Plus minus 20 mA Timer Stop Input Voltage input (24 to 300 V, DC or peak AC), dry contact input, or removal of primary current