Rural Development Department Tender

Providing and applying two coats Apex Ultima Puranature Anti-Pollution Or equivalent approved brand, paint should decomposes organic substances and inorganic gases(NOx, VOC‘s, CO, SOx, formaldehydes, etc.) in presence of natural or artificial light. It contains Graphene and nanoparticles of titanium oxide. and Absorbs CO2 (4.8 Kilogram/15 l). plaster crack should be filled by Acrylic base Crack seal/Textured Crack filler, Paint has to applied on one coat of Apex Ultima Puranature Anti-Pollution Primer or Equivalent. Warranty Should be given by the Manufaturer The work should be done by the Manufacturer Recommended applicator and he should be able to furnish stage wise onsite technical reports from the concerned company technologist.

WELL Excavation in general in soft material comprising of soft soil, soft murum, sand, hard murum with boulders in wet or dry condition for Head Works i.e. Intake Well, Connecting Pipe, Jack Well, Pump House, Supply Well, etc. for lift 0 to 1.5 M and lead of 150 M including baricating, gurading, disposing off surplus excavated stuff within a radius of 0.5 km. as directed by Engineer-in- charge, etc. complete excluding refilling. For Head Works on river or dam submergence Lift 0.00 to 1.50 m

Refilling the trenches with available excavated stuff with soft material first over pipeline and then hard material in 15 cm layers with all leads and lifts including consolidation, surcharging, etc. complete.

Providing internal cement plaster 20mm. thick in single coats in cement mortar 1:4 without neeru finish, to concrete, brick surface, in all positions including scaffolding and curing complete. Spec. No. : Bd.L.4 Page No. 368

Item No. 5:- Providing and erecting presure gauge of required capacity complete with syptio tube isolating cock suitable for 12 mm dia G.I. Pipe pressure gauge shall be installed as directed with tapping on rising main 100 mm. Dia

Item No. 14:-Providing, erecting triple spur gear type Chain Pulley Block suitable for capacity as below with 6 m lift complete with load chain and hand chain suitable for above lift, tested to 50% over load as per IS 3832 carrying ISI mark. 1 Tonne Capacity

Taking Trial Bore (Core Bore Sampling) by Calyxe machine with TCT/NX bits together undisturbed strata samples for investigation in all types of strata soft soil, murum, hard murum with boulders, soft rock hard rock & quartizite etc. The item includes all Hire & running cost of Callyx Machine conveying all materials to site of work excluding conveyance of callyx, machine and back sampling all over burden strata in glass jar and core samples serially numbered at site in a wooden Core Box, Samples to be taken at 1.0 m interval and conveying to the place as directed by Engineer-in-charge, The diameter of bore in overburden shall be 100 mm and of NX size (50mm) in other strata. The item shall also include M.S. casing pipe of 2.5 mm thick plate in overburdern only and shall be 1.0 m above GL with cap over it. In Overburden (Soft soil, murum)

Providing and fixing C.I. road box including loading, unloading and carting to site of work including all necessary excavation in all types of strata and fixing in murum packing, etc. complete. 100 mm x 225 mm (20 kg)

Providing and laying in situ, following grades of C.C. of trap/granite/quartzite/gneiss metal for foundtion and bedding incluing dewatering, form work, compaction and curing, finishing, etc. complete. PCC (1:2:4) ie M - 150

For Superstructure

Bearing cap -7.50 MT /sqm Add 5% For Bearing Capacity

Providing and casting in situ C. C. of trap/granite/quartzite/ gneiss metal of approved quality for RCC work as per detailed drawings and designs or as directed by Engineer-in-charge including normal dewatering, centering, form work, compaction, finishing the formed surfaces with CM 1:3 of sufficient minimum thickness to give a smooth and even surface wherever necessary or roughening if special finssh is to be provided and curing, etc. complete. (By weigh batching and mix design for M-250 and M-300 only. Use fo L&T, A.C. C., Ambuja, Birla Gold, Manikgad, Rajashree, etc. cement is permitted .) For Vertical wall in M -200 grade Lift 0.00 to 5.00 m

Lowering, laying and jointing in position following C.I.D/F Reflex valves, Butterfly valves and Sluice valves including cost of all labour jointing material, including nut bolts and excluding hydraulic testing etc. complete. (Rate for all class of valves.) Sluice valves PN - 1 --100 mm dia.

Lift 13.50 to 15.00 M.

RISING MAIN Item No. 1:- Providing and supplying in standard lengths Polyethelene Pipes, confirming to IS 4984 /14151 / 12786 /13488 (Latest version) with nesessary jointing material like mechanical connector i. e.thread / insert joint / quick release coupler joint/ compression fitting joint or flanged joint excludingcoupler/specials, including transportation and freight charges, inspection charges, loading / unloading charges, conveyance to the departmental stores & stacking the same in closed shade duly protecting from sunrays & rains, excluding GST levied by GI & GOM in all respect etc. complete. 140 mm hdpe 8 kg pipe

Providing and fixing M.S. chaquerred plate flooring of following thickness supported on M.S.angles (25 x 25 x 5 mm size) including welding, cutting and fabricating the plate to the required square or rounding shape, making holes in the plate, including providing and applying 3 coats of anticorrosive paint, etc. complete as directed by Engineer-in-charge. 6 mm Tk.

SWITCH ROOM Excavation for foundation / pipe trenches in earth, soils of all types, sand, gravel and soft murum, including removing the excavated material upto a distace of 50 M and lifts as below, stacking and spreading as directed by Engineer-in-charge, normal dewatering, preparing the bed for foundation etc complete.

75 mm pvc 4 kg/cm2 pipe

Item No. 8:- Providing and supplying ISI mark C.I. D/F reflux valve (non return valves) of following dia including all taxes (central and local) railway freight inspection charges loading unloading from railway wagon transportation upto departement store etc. complete IS 5312 (1984) 80 mm dia P.N. 1 with fixing

Hydraulic testing of H. D. P. E./ M. D. P. E. pipe line to specified pressure including cost of all materials and labour and water for testing for specified length including cutting, placing end cap making arrangement for filling safe water using reciprocating type pumps which should be able to provide specified test pressure gauges and other necessary equipments, labour, operation charges, etc. required for testing. The rate under this item shall also include cost of retesting, if necessary and reinstating to original position.. 140 mm HDPE 6/8 kg pipe

ESR ABSTRACT RCC ESR CAP 135000 LITR STG HT 12.00M Item.No.1 :- Designing (aesthetically), and constructing RCC elevated service reservoirs of following capacity with RCC staging consisting of columns, internal and external bracings spaced vertically not more than 4.5 meters centre to centre for E.S.R.having capacity 500 m3 & not more than 6 m c/c for E.S.R.having capacity above 500 m3 including excavation in all types of strata, foundation concret, cement plaster with water proofing compound to the inside face of the containerincluding refilling disposing of the surplus stuff within a lead of 50 meters, all labour and material charges including lowering, laying, erecting, hoisting and jointing of pipe assembly of inlet, outlet, washout, overflow and bypass arrangements as per departmental design. providing and fixing accessories such as Stainless steel ladder inside and M.S. ladder with G.I. railing outside, C. I. manhole frame and covers water level indicatiors, lightening conductor, G. I. pipe railing around walk way and top slab, providing spiral staire case from ground level to roof level, M.S.Grill gate of 2 Mtrs height with locking arrangement, B.B. masonry chambers for all valves, ventilating shafts, providing and applying three coats of acrylic emulsion with silicon additives paint to the structure including roof slab and epoxy paint to internal surface & anti-termite treatment for underground parts of the structures and giving satisfactory water tightness test as per I.S. code, The job to include painting the name of the scheme and other details on the reservoir as per the directions of Engineer-in-charge. Notes:1. The design of the structure be in accordance with relevent (I.S.3370 - 1965 or revised) 2. The design shall satisfy the stipulation as per IS 1893-1984 and I.S. 13920/1993 for seismic focrce and I.S.- 11682/1985 for R.C.C. staging of overhead tanks. 3. For design having more than 6 columns, Providing of internal bracing is obligatory,. External bracking is also obligatory. 4.. The entire structure shall be in M 300 mix only. 5. Plain round mild steel bars grade - I confirming to I.S,432 Part-I or high yield strengh deformed bars confirming to I.S. 1786 or I.S. 1139 shall be used, grade-II mild steel bars will not be allowed. 6. Irrespective of the type of foundation proposed in the design, one set of bracing be provided at the gound level. 7. These rates include providing, M.S. ladder for E.S.R's upto 2 lakhs liters capacity and providing sprial staircase for E.S.R. above 2 lakhs liters capacity. 8. Stagging shall have to be designed with stresses of M-250 for ESR. However all RCC construction should be done in M-300 9. These rates are including the cost of uplift pressure if any and entire dewatering during execution. In case of water logging area where water is struck at shallow depth extra provision of dewatering shall be made as per site condition. 10. All condition given in the Member Secretary"s Circular No.MJP/TS-I/350/1668 dt. 2.8.97 and MJP/S-I/350/2127 dt.13.7.99 shall be strictly followed and additional cost, if any due to these conditions is included in the rates mentioned below. 11.. 75% part rate shall be payable for reinforced cocnrete and plastering items of containers of E.S.R. till satisfactory hydraulic testing for water tightness is given ; and till that work shall be treated as incomplete. 12. The rates indicated in the table are excluding the cost of pipes, specials and valves required for inlet, outlet washout overflow and by-pass arrangement. The scope of work, however inclueds cost of erecting, laying and jointing of pipes and valvews including cost of jointing materials upto 5M beyond outer face of outermost column. 13. For ESR upto 500cum capacity C.I.D. double flanged pipes upto 300mm dia shall be provided and C.I.Specials shall be used.For ESR above 500 cum capacity C.I./M.S. pipes assembly with minimum 8mm thick ness up to 500mm dia. And minimum 10mm thickness above 500mm dia can be used with proper anti-corrosive epoxy teratment from inside and outside. 14. Below mentioned rates are for foundation, with individuals footing with bearing capacity of 30 tonnes per square metre. For raft foundations, these rates shall be increased by 7.5% wheresafebearing capacity ( SBC) is 5 M.T. per Sq.m and by 5% where SBC is more than 5 MT/Sqm. and upto 10MT/Sq.m. This percentage of 5% or 7,5% is applicable for estimation of amount of L.S. items ESR for Extra item due to change from individual footing foundation to raft actual increase in concrete and steel quantities be paid as per relevent DSR Item. 15.The rates shall be increase by 30% for brearing piles upto depth of 10m and for further increased in depth by 5M each it shall be increased by another 10% These rates are applicable where raft is not reasible for pile foundation sulfate resistant cement shall only be used. Single pile for the column is not permitted Group of piles shall be designed with pile cap for each column of ESR. 16. These rates are applicable for staging height of 12 M These rates shall be increased or decreased for per metre variation in the staging height as below 12 to 16 M staging 2% per metre 16 to 20m staging 3% per meter 20 M and abovd - 4% per metre I.e. for 17m stagging height percentage calculation will be like below 12 to16m = 4 x 2 = 8% 16 to 17 m x 1 x 3 = 3% Total = 11 % For 21 m stagging height Percentage calculation will be like below 12 to 16m = 4 x 2 = 8% 16 to 20m = 4 x 3 = 12% 20 to 21m = 1 x 4 = 4% Total = 24% 17. Following rates are for seismic zone-III for Zone-IV these rates shall be increased by 5% and for Zone-II, these rates shall be decreased by 5% concerned Executive Engineer shall confirm the seismic zone for the scheme from seismic zones plan before estimation and adopt appropriate rates as per actual seismic zones( Seismic maps attached in this C.S.R.) Note:- 1) Conditin from Sr.No.1 to 11 shall form a part and parcel of the tender papers and shall be included in the DTP for works of R.C.C.E.S.R. Note:-2) Condition from Sr.No.12 to 17 are for estimation purpose only and shall not be appear in the tender. Cost of 135000 litres capacity 12 m stage height ESR Add for raft foundation 7.5 % Net Total Cost of 135000 litres capacity 12 m stg. height ESR RCC ESR 135000 lit.Cap.

Item No. 12:-Providing tools with tool box etc complete

Lowering, laying and jointing with P.V.C. pipes and specials of following class and diameter including cost of conveyance from stores to site of works including cost of all labour, material, except cement solvent, rubber ring, as per IS code, etc. complete (with cement solvent joint / ring fit joint). 160 mm pvc 4 kg/cm2 pipe

Item No. 10 :- Supplying and erecting Galvanized cast iron earth plate 60 X 60 X 0.6 cm buried specially preposed earth pt[top edge of plate 1.5 m below ground refilling with 30 kg chorcoal and salt in alleviate layers neccessory length of double G.I. earth strip connected to the plate G.I. nuts bolt 12 mm dia iwth Bituminous compound and connected to nearest switch gear with end socket as per directed supplying and erecting 19m dia ventical G.I. pipe 1.5 m long with funner and mesh at top included in the scope of work.

Lift 10.50 to 12.00 M.

Providing and fixing in position air valve shaft including providing and fixing GI Medium Class or 6 mm thick M.S. pipe shaft 2.70 M long over branch flange of air valve tee, providing PCC block of M-150 concrete 150 mm thick around the air valve tee including encasing of vertical shaft in PCC M-150 as shown in type design together with providing and making flanged joints wherever required and fixing of air valve over the shaft excluding cost of air valve and branch flanged air valve tee. etc. complete as per type design and as directed by Engineer-in-charge for following diameters of pipe lines (type design attached.) Pipe dia. upto 150 mm dia

Providing and laying in situ Cement concrete of trap/granite/quartzite/ gneiss metal for RCC work in foundation like raft, grillage, strip foundation and footing of RCC columns and steel stanchions including normal dewatering,plywood form work, compaction, finishing and curing, etc, complete. (By weigh batching and mix design for M-250 and M-300 only. Use of L & T, A.C.C., Ambuja, Birla Gold, Manikgad, Rajashree, etc. cement is permitted.) RCC M 200 for Footing

Lift 15.00 to 16.50 M.

Providing and casting in situ C. C. of trap/granite/quartzite/ gneiss metal of approved quality for RCC work as per detailed drawings and designs or as directed by Engineer-in-charge including normal dewatering, plywood form work,bully/steel prop ups, compaction, finishing the formed surfaces with CM 1:3 of sufficient minimum thickness to give a smooth and even surface wherever necessary or roughening if special finssh is to be provided and curing, etc. complete. (By weigh batching and mix design for M-250 and M-300 only. Use fo L&T, A.C. C., Ambuja, Birla Gold, Manikgad, Rajashree, etc. cement is permitted .) RCC M 200Slabs

75 mm pvc 4 kg/cm2 pipe

Excavation for foundation / pipe trenches in earth, soils of all types, sand, gravel and soft murum,Excavation for foundation / pipe trenches in hard murum and boulders, W.B.M. road,, including removing the excavated material upto a distance of 50 metres and lifts as below, stacking and spreading as directed, manual dewatering, preparing the bed for foundation and excluding backfilling, etc. complete.

Sluice valves PN - 1 --125 mm

Lift 5.0 To 10.00 M

Providing and fixing in position steel bar reinforcement of various diameters for RCC piles, caps, footings, foundation, slabs, beams, columns, canopies, staircases. newels, chajjas, lintels, pardies, copings, fins, arches, etc. as per detailed designs, drawings and schedules; including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required, etc. complete. (including cost of binding wire)

Sluice valves PN - 1 --80 mm dia.

Providing and laying polished Shahabad Stone flooring 25mm to 30mm thick and of required width in plain / diamond pattern on a bed of 1:6 C.M. including cement float, filling joints, with neat cement slurry, curing, polishing and cleaning complete. Spec. No. : Bd.M.3 Page No. 380

Item No. 6:- Providing ISI mark G.I. Pipe of following class and dia including all local and central taxs octrai inspection charges transporatation to store etc… complete medium 15 mm. Medium Providing L.L joint

90 mm pvc 4 kg/cm2 pipe

110 mm pvc 4 kg/cm2 pipe

Provision for Chemical charges for one month -- etc comp. For 3 Months requirement (0.287 x 90x5 kg )=0.13 MT

Providing and filling around the well boulders filling of selected variety and size of boulders including cost of all materials, labour, transportation, etc. complete with all leads and lifts.

In Hard rock other than quartzite

PUMPING MACHINARY Item No. 1:- Providing erecting and giving test of submersible pump set confirming to IS. 8034 and motor confirming to I.S. 9283 with water proof binding pump shall be suitable for various delivery head and discharge with stainless steel shaft motor suitable for working on 415 10% 3 ph 50 Hz A.C. supply with cable gurad thrust carbon fiber bearing to with stand entire hydrulic thrust .the pump set shall be suitable for direct coupling with suitable saction stainer pump should have suitable discharge outlet as per manufacture design antithrust stream non retun valve shall be provided with the pump 3 m submersible copper conductor cable in single / double run 2 pair of erection clamp 65 mm width 10 mm thick shall be provided with each pump Submersible pump 17.5 HP with errection

140 mm pvc 4 kg/cm2 pipe

Providing and laying in situ cement concrete M-10 /1:3:6 of trap/granite/quartzite/gneiss metal for foundation and bedding including bailing-out water manually formwork, compacting, cover­ing newly laid concrete by gunny bag, plastic or tarpaulin, curing etc complete.

Providing and laying in situ, following grades of C.C. of trap/granite/quartzite/gneiss metal for foundtion and bedding incluing dewatering, form work, compaction and curing, finishing, etc. complete. PCC (1:2:4) ie M - 150

Item No. 7 :- Providing and supplying G.I. special at site including all taxes (central & Local )RailwayFright Insurances on loading from Railway wagon Loading Truck Transport to store/site unloading etc.. Comp. As directed by Engineer in Charge

Providing and fixing in position steel bar reinforcement of various diameters for RCC pipes, caps, footings, foundation, slabs, beams, columns, canopies, staircases. newels, chajjas, lintels, pardies, copings, fins, arches, etc. as per detailed designs, drawings and schedules; including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required, etc. complete. (including cost of binding wire)

Providing and casting in situ Cement Concrete of trap/granite/quartzite/ gneiss metal of approved quality for RCC work as per detailed drawings and designs or as directed by Engineer-in-charge including normal dewatering, plywood form work,bully/steel prop ups, compaction, finishing the formed surfaces with CM 1:3 of sufficient minimum thickness if special finish is to be provided and curing, etc. complete. (By weigh batching and mix design for M-250 and M-300 only. Use of L&T, A.C. C., Ambuja, Birla Gold, Manikgad, Rajashree, etc. cement is permitted ) RCC M 200 for column

Providing and fixing in position C.I. Type dapuri steps of 22 mm dia. M.S. bar step with proper anchorage, etc. and providing and applying 3 coats of ant-corrosive paint, etc complete as directed by Engineer-in-charge.

Providing Bricks masonry in cement mortar 1:6 using Second class burnt bricks in superstructure including striking joints, raking out joints, watering and scaffolding complete. For Plinth

Item No. 11:- Providing and supplying internal elactrification to switch room etc. comp. Rate analysis attached

Item No. 4:- Supplying and erecting G.I. Pipe 'B' in position for suction and delivery for submersible pump including pumbing with socket and necessary material 80 mm. Dia

150 mm dia. D/F Sl. Valve PN 1.0

Providing and supplying double flange sluice valves confirming for IS 2906/14846 including warn gear arrangement as per test pressure stainless steel spindle caps including all taxes transportation etc complete. Sluice valves PN - 1 --100 mm dia.

Filling in plinth and floors murum bedding in trenches with approved murum from excavated materials from foundation 15cm to 20cm layers including watering and compaction complete For murrum bedding.

150 mm dia.D I D/F pipe

Excavation in general in hard material comprising of soft rock, hard rock, Manjara rock, etc, by blasting / controlled blasting, chiselling as required in wet or dry condition for Head Works i.e. Intake Well, Connecting Pipe, Jack Well, Pump House, supply Well, etc. for lift 0 to 1.5 M and lead of 150 M including baricading, guarding, disposing off surplus excavated stuff within a radius of 0.5 km. as directed by Engineer-in-charge, excluding refilling. Lift 6.00 to 7.50 M.

Lift 16.50 to 18.00 M.

Filling in plinth and floors / trenches with contractor’s murum for bedding in 15cm to 20cm layers including watering and compaction complete.

Lift 7.50 to 9.00 M.

Excavation for foundation / pipe trenches in earth, soils of all types, sand, gravel and soft murum,Excavation for foundation / pipe trenches in hard murum and boulders, W.B.M. road,Excavation for foundation / pipe trenches by blasting in soft rock and old cement and lime masonry foundition asphalt road,Excavation for foundation / pipe trenches in hard rock by controlled blasting,, including removing the excavated material upto a distance of 50 metres and lifts as below, stacking and spreading as directed, manual dewatering, preparing the bed for foundation and excluding backfilling, etc. complete.

In Weathered rock / Soft rock

Providing and applying white-wash in two coats on old/ new plas­tered or masonry surfaces and asbestos cement sheets including scaffolding and preparing the surface by brushing & brooming down complete.

TRAIL RUN Item No. 1:- Commisioning running and maintaining the scheme to quantites, rated capacity, including manning necessary personnel such as operator, valveman, etc. as per requirements of the scheme and who should also administer chemical dose for a period of 1 month for individual scheme and 3 months for regional scheme, together with training of personnel spared by MJP/ Local Body and handing over the scheme to Local Body after completion of the above period as directed by Engineer-in-charge. Trial Run For 1 month

Add.Distribution Item No. 1:- Providing and supplying in standard lengths ISI mark rigid unplasticised PVC pipes suitable for potable water with solvent cement joints including cost of couplers, as per IS specification no. 4985 / 1988 including all local and central taxes, transportation, freight charges, inspection charges, loading, unloading, conveyance to the departmental stores / site and stacking the same in closed shed duly protected from sun rays and rains including cost of jointing material i.e. solvemt cement, etc. complete (selffit type to be jointed with cement solvent). 160 mm pvc 4 kg/cm2 pipe

Providing at site of works HDPE.specials suitable for above pipes including cost of all taxes, freight charges, octroi, loading, unloading and conveyance to Deptt.store etc. complete. 1 % of Cost of pipes

Lift 4.50 to 6.00 m

Lift 3.00 to 4.50 m

Item No. 3: - Supplying and erecting Flat flexible submersible cable with copper conductor PVC insulated and PVC sheathred 1 x 4 x 6 sqm

Taking Horizontal bore with transportation of machinery in soil or hard strata of wet drilling work and all other charges

Carrying out recuperation / yeild test for ascerting the discharge of constructed well / excavated profile as direrted by Engineer in charge.The test carried out by drawing down water from the well/ profile below normal / subsoil water level upto full depth rise in water level is recorded. The normal water level / subsoil water level in the well / profile as well as strainer / suction level at pump as per design of W.S. scheme shall be recorded prior. to the test including cost of all materials.overhead,labours etc. completed as directed. The test shall be carried out as per technical circular No.2597 dt. 20/11/97 and shall be carried out for 7 days. Less than 25000 Lit/hr. above

140 mm pvc 4 kg/cm2 pipe

Lift 12.00 to 13.50 M.

Providing and supplying Kinetic Double Orifice type Air Valves as per IS- 14845-2000 and MJP’s standard specifications of approved make and quality of following diameters including railway freight, inspection charges, unloading from railway wagons, loading into truck, transportation upto departmental stores, unloding and stacking excluding GST levied by GOI & GOM in all respect etc. complete. 40 mm Dia. vale Flanged Type PN 1

Refilling the trenches with available excavated stuff with soft material first over pipeline and then hard material in 15 cm layers with all leads and lifts including consolidation, surcharging, etc. complete.

Providing and fixing signboards of size size60x80cm made out of 14gauge M.S.Sheet with retroreflective sheeting of Engineering Grade as per M.O.T.specificationNo.801-3(1993)white reflective background,lettering symbol bordering of black non reflective paint including 3.65 metre long M.S.angle onepost of 65x65x6mm size duly painted with white and black bands including fixing the boards of M.S.angle with galvanised nuts and bolts and washer.The Board shall be as per IRC-67-1977 including conveying fixinging round with C.C.1:4:8 block of size0.60x0.60x0.75m,with 7 year guarantee for the sheeting etc.complete. Mild Steel Board with Engineering Grade.

In Weathered rock with boulders

Lift 1.50 to 3.00 m

Providing and fixing steel window of various sizes as per detailed drawings fabricated from IS standard sections without hot dip zinc coating without / with ventilator including fabrication, glazing with non-acentinic / plain / obscured glass panels of approved type and quality, all fixtures and fastening without teak wood boxing, and architraves and finishing with one coat of primer complete with guard bars 12mm square bar 10cm center to center.Bd.T.53 Page No.509.

Providing and supplying ISI standard C. I. specials & fittingwith sealing rubber gasket of S.B.R,complete with cast iron follower gland and M. S. nut bolts coated or otherwise protected from rusting and suitable for D.I.pipes including cost of labour, materials, and transportation to stores, loading and unloading excluding GST levied by GOI & GOM in all respect etc. complete as per IS-9523.

Sluice valves PN - 1 --80 mm dia.

110 mm pvc 4 kg/cm2 pipe

Item No. 2:- Providing erecting commissinory L.T. panel board with all required accessories for the pump in above item No. 1.. etc.complete

Item No 1 Providing and laying in situ Cement concrete of trap/granite/quartzite/ gneiss metal for PCC work below foundation and footing including normal dewatering,plywood form work, compaction, finishing and curing, etc, complete. PCC M150

Providing and constructing B.B. masonry valve chamber with 15 cm thick 1:3:6 proportion PCC bedding, excluding excavation, B.B. masonry in C.M. 1:5 Proportion precast RCC frame and cover, etc. complete as directed by Engineer-in-charge. Size 90 x 45 x 120 cm.

Lowering, laying and jointing in position following C.I.D/F Reflex valves, Butterfly valves and Sluice valves including cost of all labour jointing material, including nut bolts and excluding hydraulic testing etc. complete. (Rate for all class of valves.) Sluice valves PN - 1 --80 mm dia.& Reflux Valve

Scour valves PN - 1 --80 mm dia.

Sluice valves PN - 1 --150 mm dia.

Providing stuctural steel work in single stanchions composed of RSJ, channel, etc, with caps, bases, mild steel plates, angles, brackets, cleats, gusset plates, anchor bolts, etc. as per detailed design and drawing or as directed by Engineer-in-charge including cutting, fabrication, hoisting, erecting, fixing in position, making riveted/ bolted / welded connections and one coats of anticorrosive paint and over it two coats of oil painting, etc. complete.

Providing and casting in situ C. C. of trap / granite / quartzite/ gneiss metal of approved quality for RCC works as per detailed drawings and designs or as directed by Engineer-in-charge including normal dewatering, ,plywood form work,bully/steel prop ups compaction, finishing the formed surfaces with C. M. 1:3 of sufficient minimum thickness to give a smooth and even surface wherever nesessary or roughening if special finish is to be provided and curing, etc. complete. (By weigh batching and mix design for M-250 and M-300 only. Use of L&T, A.C.C., Ambuja, Birla Gold, Manikgad, Rajashree, etc. cement is permitted.) Lift 5.0 To 10.00 M

Providing and casting in situ C. C. of trap / granite / quartzite/ gneiss metal of approved quality for RCC works as per detailed drawings and designs or as directed by Engineer-in-charge including normal dewatering, ,plywood form work,bully/steel prop ups compaction, finishing the formed surfaces with C. M. 1:3 of sufficient minimum thickness to give a smooth and even surface wherever nesessary or roughening if special finish is to be provided and curing, etc. complete. (By weigh batching and mix design for M-250 and M-300 only. Use of L&T, A.C.C., Ambuja, Birla Gold, Manikgad, Rajashree, etc. cement is permitted.) RCC M 200 Beams, Lintels

Providing and supplying double flange sluice valves confirming for IS 2906/14846 including warn gear arrangement as per test pressure stainless steel spindle caps including all taxes transportation etc complete. Sluice valves PN - 1 --125mm dia.

Dewatering the excavated well works by using pumps and other devices including disposing off water to safe distance as directed by Engineer-in-charge (including cost of machinery, labour, fuel), etc. complete. The provision made for dewatering in the tender being on lumpsum basis the same shall have reduced / increased proporpotionatly as the lenght of approach channel , connecting main or approach bridge reduced/ increased during actual execuction

Providing and supplying double flange sluice valves confirming for IS 2906/14846 including warn gear arrangement as per test pressure stainless steel spindle caps including all taxes transportation etc complete. 125 mm dia. D/F Sl. Valve PN 1.0

Providing, and fixing 80 mm dia A.C./P.V.C. pipe weep holes at 1.5 M c/c staggered including cost of all materials and labour involved with all leads and lifts.etc. complete with all leads and lifts.

B) Providing and erecting P.V.C. armoud cable 1100V grade with ISI mark 3.5 core Solid / standard aluminium conductor with 6 mm thick 25 mm width m.s.. Spacer with G.I. Earth wire 6 Sq. mm complete erected on wall / on Pole with 25 X 3mm M.S. Clamp in provided trench in an approved manner 4 Core 10 Sq. mm

Provision for Energy charges for one month -- etc comp.

Refilling the trenches with available excavated stuff with soft material first over pipeline and then hard material in 15 cm layers with all leads and lifts including consolidation, surcharging, etc. complete.

Providing and casting in situ C. C. of trap/granite/quartzite/ gneiss metal of approved quality for RCC work as per detailed drawings and designs or as directed by Engineer-in-charge including normal dewatering, centering, form work, compaction, finishing the formed surfaces with CM 1:3 of sufficient minimum thickness to give a smooth and even surface wherever necessary or roughening if special finssh is to be provided and curing, etc. complete. (By weigh batching and mix design for M-250 and M-300 only. Use fo L&T, A.C. C., Ambuja, Birla Gold, Manikgad, Rajashree, etc. cement is permitted .) For Slab & Landing in M -200 grade

Providing and constructing B.B. masonry valve chamber with 15 cm thick 1:3:6 proportion PCC bedding, excluding excavation, B.B. masonry in C.M. 1:5 Proportion precast RCC frame and cover, etc. complete as directed by Engineer-in-charge. Size 90 x 45 x 120 cm.

Providing and making flaged Joint to flange, C.I. Pipes / M.I. Pipes and specials of all classing including cost of jointing material rubber packing nut bolts labour charges hydrulic testing etc. complete

Providing and supplying ISI mark CI D/F reflux valves (non-return valves ) of following dia including all taxes (Central and Local), railway freight, inspection charges unloding from railway wagon, loading into truck, transportation upto departmental stroes/ site, unloading, stacking etc. complete. Reflux valves as per I.S.5312 Part I (1984)With Third Party Inspection NRV 125 mm dia.

Providing rough cast cement plaster externally in two coats to concrete,brick or stone masonry surfaces inall positions with base coat of 12to15mm thick in C.M.1:4 and rough cast treatment 12mm thick in proportion 1:1 1/2:3 including scaffolding and fourteen days curing complete. Bd.L.8 Page Number 370

90 mm pvc 4 kg/cm2 pipe

140mm hdpe 6 kg pipe

Filling in plinth and floors murum bedding in trenches with approved murum from excavated materials from foundation 15cm to 20cm layers including watering and compaction complete. For murrum bedding

Providing and fixing wall mounting type name board duly painted all details of pumping machinery make, model frame no. DR no. Date of installation commissioning manufacture year agoncy name aggrement no details of G.I. Shal 18 gauge of required size duly painted with red oxide and enamus paint for dispaying the above details board shall be provided with suitable T.W. bottom back side name board

Providing and supplying ISI standard CI double flanged pipes excluding GST levied by GOI & GOM in all respect including railway freight, insurance, unloading from railway wagon, loading into truck transport to stores, unloading etc. complete as directed by Engineer-in-charge 125 mm dia.D I D/F pipe

Providing at site of works PVC.specials suitable for above pipes including cost of all taxes, freight charges, octroi, loading, unloading and conveyance to Deptt.store etc. complete. 10% of Cost of pipes

Sluice valves PN - 1 --150 mm dia.

Providing & applying washable oil-bound distemper of approved colour and shade to old & new surfaces in two coats including scaffolding, preparing the surfaces. (excluding the primer coat.) complete.

Item No. 9:- Providing and supplying ISI mark C.I.D.F sluice valve of following dia including all taxes (central and local railway freight inspection entries unloading from railway wagon loading into truck transportation upto departmental store/site unloading stacking etc. complete. 80 mm dia P.N. 1 with fixing on delivery side ( 4966+1251)

Providing and fixing solid core flush door commercial in single leaf 35mm thick without ventilator commercial type of exterior grade as per detailed drawing including non teak seasoned wood door frame 60mm x 100mm with wrought iron hold fast, on both sides and finishing with oil paint three coats complete. As directed by Engineer in charge. a) With Aluminum oxidized fixtures & fastening