Rural Development Department Tender

SITC with wires, Outdoor Architectural 1200mm LED Non Integral Linear Wallwash luminaire with System wattage not more than 40W, System efficacy ≥45LPW, CCT RGBW (W=3000K) with 4in1 LED for uniform illumination, System lumen output should be ≥450lm(±10%) with all RGBW channels ON, Fixture should be compatible with DMX512, Separate outdoor IP Rated Box for Driver Placement , Single piece Housing made of Extruded Aluminium with Aluminium End caps ensuring optimum thermal management, Heat Resistant Clear tempered Glass with Secondary PMMA lens with Available Precise Beam angles 10°,15°,30°,45°,60°, 10°X30v,10°X60°, 30°X60°(As per approved concept & Site requirement). Ingress Protection ≥ IP66 with Impact Resistance ≥ IK05. Remote type Driver should be high efficiency isolated constant voltage driver with Protection Class 1. Fixture should have inbuilt 4 channel decoder. Total Surge protection of 20KV or more, No-load protection, Over voltage protection, & Short circuit protection, Life 50,000 B Hrs@L70, CRI80 (for While LED), THD10% , PF0.95, Operating voltage 90-305V AC, Operating Temp 0 to +50°C, Operating Humidity 10-90%, Fixture should be factory fitted with Antiglare Visor. Fixture weight should not be more than 1.6KG(±5%) to avoid excessive load on facade structure. Fixture should come with min. 0.5Mtr. long loop in loop out cable with IP connector, Manufacturer emblem/logo embossed into the Aluminium housing/End Caps to allow OEM identification & traceability till the life of the fixture.Suitable for mounting on surface using inbuilt mounting brackets with 180° tilt adjustment at site . Fixture should be supplied with IP Box with Compatible Driver and Plug & Play Loop In loop out cables specially designed for the luminaire ( to be quoted as separate line item in BOQ). Contractor should make necessary provisions for proper installation of luminaires at site with exceptional workmanship considering all safety standards. Luminaire

SITC with wires, Outdoor Architectural 500mm LED Non Integral Linear Wallwash luminaire with System wattage not more than 20W, System efficacy ≥45LPW, CCT RGBW (W=3000K) with 4in1 LED for uniform illumination, System lumen output should be ≥1350lm(±10%) with all RGBW channels ON, Fixture should be compatible with DMX512, Separate outdoor IP Rated Box for Driver Placement , Single piece Housing made of Extruded Aluminium with Aluminium End caps ensuring optimum thermal management, Heat Resistant Clear tempered Glass with Secondary PMMA lens with Available Precise Beam angles 10°,15°,30°,45°,60°, 10°X30v,10°X60°, 30°X60°(As per approved concept & Site requirement). Ingress Protection ≥ IP66 with Impact Resistance ≥ IK05. Remote type Driver should be high efficiency isolated constant voltage driver with Protection Class 1. Fixture should have inbuilt 4 channel decoder. Total Surge protection of 20KV or more, No-load protection, Over voltage protection, & Short circuit protection, Life 50,000 B Hrs@L70, CRI80 (for While LED), THD10% , PF0.95, Operating voltage 90-305V AC, Operating Temp 0 to +50°C, Operating Humidity 10-90%, Fixture should be factory fitted with Antiglare Visor. Fixture weight should not be more than 1.6KG(±5%) to avoid excessive load on facade structure. Fixture should come with min. 0.5Mtr. long loop in loop out cable with IP connector, Manufacturer emblem/logo embossed into the Aluminium housing/End Caps to allow OEM identification & traceability till the life of the fixture.Suitable for mounting on surface using inbuilt mounting brackets with 180° tilt adjustment at site . Fixture should be supplied with IP Box with Compatible Driver and Plug & Play Loop In loop out cables specially designed for the luminaire ( to be quoted as separate line item in BOQ). Contractor should make necessary provisions for proper installation of luminaires at site with exceptional workmanship considering all safety standards. Luminaire Dimensions for ref. Not more than L=500mm, W=39mm(±5%), H=45mm(±5%) .Manufacturer should have BIS with R No. , LM79 from NABL Accredited Lab, TTC from NABL Accredited Lab, LM80, Photometric & illumination Code Diagram, Technical Data sheet soft copy for submission if requested by Engineer in-charge. Fixture should have

SITC with wires, Outdoor Architectural LED Circular Projector flood light with System wattage not more than 15W, System efficacy45LPW (±5%), CCT RGBW (W=3000K) with 4in1 LED for uniform illumination with Non- Integral Driver & Decoder, Fixture should be compatible for DMX512. Housing should be PDC Aluminium alloy ensuring optimum thermal management , Fixture should be available in clear optics with possible beam angles 25°, 30°,40°, 50°(As per approved concept & Site requirement). Secondary Lens should be of PMMA material & covered with Heat Resistance Toughened Glass cover, Hinge design should be easily adjustable with precision dial feature for 90° tilt angle adjustment, Ingress Protection should not be less than IP66, Impact Resistance should be IK08 or more. Fixture height should be approx. 185mm (±15mm) with Normal horizontal tilt position. Snoot Dia should not be more than 93mm (±5mm) , Fixture should be surface/Wall mounted as per site requirement. Driver should be integral isolated CC/CV Driver. Total Inbuilt and Additional Surge protection of more than or equal to 10KV along with other necessary protections No Load protection, Over voltage protection, Short circuit protection. LED Life should be 50,000 B Hrs@L70 B10, THD should be less than 5% , PF0.95, Operating voltage range 140-270V AC, Operating ambient Temp 0 to +50°C, Operating Humidity 10-90%. Fixture weight should not be less than 3.5KG (±10%) ensuring material & built quality. Powder coating should be corrosion resistant Nano technology powder coating in Silver grey colour. Standard Power cable should have IP67 connector. Technical Data Sheet, Type test Certificate from In-House NABL accredited Lab should be submitted on request. Manufacturer/OEM emblem/logo should be embossed into the Aluminium housing to allow identification of OEM & traceability till the life of the fixture. Manufacturer/OEM should have complete manufacturing set up in India with In-house capability of Housing, PCB & Driver Manufacturing and In-House NABL Accredited LAB for Electrical & photometry testing. Luminaire should comply with Performance & safety standards IEC 60598/ IEC60950 , IEC 60529, IS 10322-5, IS 161-03/05/06/07, Surge : IEC 61000-4-5, EMC : EN 55015