Rural Development Department Tender

Excavation in Hard Mirum including boulders up to 0.6 m diameter (0.113 cum) for canal, seating of embankment, filter drain / catch water drains etc., and placing the excavated material neatly in dump area or for formation of service road as directed including cost of all materials, machinery, labour, dressing bed and sides to required level and profile etc. complete with lead up to 15 m and 6 m lifts as directed

Excavation in Soft Rock without blasting including boulders up to 0.6 m diameter (0.113 cum) for canal, seating of embankment, filter drain / catch water drains etc., and placing the excavated soft rock neatly in dump area or for formation of service road as directed including cost of all materials, machinery, labour, dressing bed and sides to required level and profile etc. complete with lead up to 15 m and 6 m lifts as directed

Excavation in hard rock of all toughness by brealer including boulders above 0.6 m dia.(0.113Cum) minimizing damage to side slopes of excavation in water prism area by adopting any one or combination of line drilling/pre-splitting/smooth blasting techniques and placing the excavated rock neatly in approved dump area as directed including cost of all materials, machinery, labour, leveling bed etc., complete with lead up to 15 m and 6 m lifts as directed

Drilling 35 mm dia anchoring holes in rock as directed and fixing 25 mm dia steel anchor excluding grouting and cost of anchor bar etc. complete.

Providing and laying in situ cement concrete of grade M-15 of trap / granite / gneiss / quartzite / graded metal (20 msa) for PCC with or without surface reinforcement/ RCC concreting requiring heavy or special type of shuttering for works of gallery, sluice, spillway crest, spillway downstream face, energy dissipating structures, intake structures, training walls, piers, abutments etc. with Concrete Mixer with shuttering and scaffolding, placing, compacting, curing etc complete with an initial lead of 50 m & lift of 1.5 m

Providing and fixing TMT steel reinforcement bar as per design and drawing including cutting, bending, hooking binding with G.I, wire as directed with all lead & lift etc completed. (Rates as per joint plant Committee.) 10 mm Main

Providing and fixing TMT steel reinforcement bar as per design and drawing including cutting, bending, hooking binding with G.I, wire as directed with all lead & lift etc completed. (Rates as per joint plant Committee.) 10 mm Dist

Providing and fixing TMT steel reinforcement bar as per design and drawing including cutting, bending, hooking binding with G.I, wire as directed with all lead & lift etc completed. (Rates as per joint plant Committee.) 25 mm Anchor

Providing and fixing Mild Steel Channels of Size 150x 75 mm in side groove suitable to fit the needle. With all labour charges etc. complete .

Manufacturing with QAP & fabrication of KT weir needle gates-strighttype size 2.15x0.5M-94 kg. weight as per relevant Indian Standards with all material, Mild steel confirming to IS 2062, Rubber seal confirming to IS 4623 & Welding electrods A WS E 6013 for general weld joints. It includes all materials, Labour chareges, machinery charges, 1 km lead charges of transporatation, loading and unloading charges of Gate parts at site, Inspection & Quality control charges, Sand blasting, Painting with one coar of Zinv rich primer on dry film to give total dry film thickness 70 +/-5 microns and 2 coats of sloventless coal tar epoxy paint applied to give dry film thickness of 150+/-5 micron per coat as per IS 14177

Providing and constructing 230 mm thick dry rubble stone pitching using stones and stone chips from approved source from borrow area including cost of all materials, labour, hand packing / wedging stone chips, finishing etc., complete with lead up to 50 m and all lifts. excluding royalty of material.

Providing and fixing canal information board of 1.2 x 0.75 m prepared on 16 gauge M.S. sheet with angle iron frame of size 35 x 35 x 3 mm with cross bracing of size 25 x 25 x 3 mm including painting with one coat of zinc chromate storing primer and two coats each of green/white back ground and back side grey store enameled bonded with red retro reflective sheet Engineering grade, border / letters / numeral / arrows coated with non peal able crystal clear protective transparent coat retaining 100% reflection including two angle iron post of size 50x50x5 mm of 3.65 m long inflated at bottom drilled on top and painted in white and black bonds of 30 cm with four numbers high strength of G.I. bolts and nuts of size 10 mm dia. and 20 mm long sheet and angle iron post in one piece without joints including all taxes, conveying, fixing in ground with cement concrete in M-15 block of size 60 x 60 x 75 cm as directed by Engineer-in-Charge.

Royalty not included in rates

GST(18%)

GIS(1%)