Rural Development Department Tender

LIFT 4.50 to 6.0 M

Item No.2 :-Excavation for in general in Hard material comparising of soft rock, hard rock manjra rock in wet or dry condition for head works ie. Intake well connecting main jack well pump house supply well etc. for lift 1.50 M and lead of 150 M including barricating guarding disposing off surplus excavated stuff with radius of 0.50 km as directed by engineer in charge.LIFT 6.0 to 7.5 M

LIFT 7.5 to 9.0 M

LIFT 9.0 to 10.5 M

LIFT 10.5 to 12.0 M

LIFT 12.0 to 13.5 M

LIFT 13.5 to 15.0 M

Item No.3 :-Providing & laying in situ,following grade of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including dewatering, form work, compacting and curing, finishing etc. complete.M-15 GradeLevelling course

Item No. 4 :-Providing and laying in situ Cement concrete of trap/granite/quartzite/ gneiss metal for RCC work in foundation like raft, grillage, strip foundation and footing of RCC columns and steel stanchions including normal dewatering, form work, compaction, finishing and curing, etc, complete. (By weigh batching and mix design for M-250 and M-300 only. Use of L & T, A.C.C., Ambuja, Birla Gold, Manikgad, Rajashree, etc. cement is permitted.) Excluding M.S. or Tor reinforcement.For foundation (M-30)Foundation for jack well BeamLift 12 m to 15 m 600x300

Item No.5 :-Providing and casting in situ C.C. of trap / granite / quartzite / gneiss metal of approved quality for RCC work as per detailed drawings and designs or as directed by Engineer in charge including normal dewatering, plywood formwork, bully / steel prop-ups, compaction, finishing the formed surfaces with CM (1:3) of sufficient minimum thickness to give a smooth and even surface wherever necessary or roughening if special finish is to be provided and curing, etc. complete. (By weigh batching and mix design for M-250 and M-300 only). Use of L&T, A.C.C., Ambuja, Birla Gold, Manikgad, Rajashree, etc. cement is permitted. (Excluding M.S. or Tor reinforcement).For RCC M-300 grade slabs / landings / vertical walls / waist slabs / steps for staircase.Lift 0 to 5 (AGL)

Lift 0 to 5 (BGL)

Lift 5 to 10 m (BGL)

Lift 10 to 15 m (BGL)

Item No. 6 : -Providing and fixing in position for steel bar reinforcement of various diameters for RCC piles, caps, footings, foundations, slabs, beams, columns canopies, stair cases, newels, chajjas, lintels, pardies, copings, fins, arches, etc. as per detailed designs, drawings and shedules including cutting, bending, hooking the bars, binding with wires, or tack welding and supporting as required etc. complete(including cost of binding wire). @ 80 kg/cum of concrete.Lift 0 to 5 m (BGL+AGL)

Lift 5 to 10 m (BGL)

Lift 10 to 15 m (BGL)

Item No. 7 :-Dewatering charges for estimation purpose for head works in river basin or dam Jack well of 6 m dia30 days/8hr/5bhp/2hp

Item No.8:-Providing and fixing MS ladder .50 wide consi..75 x 10 mm MS flat as stringer and 16 mm dia MS bars in double rows as steps place at 25 Mc/c including cost of material labour welding anchoring and applying three coats of anticorrossive paint etc. complete

Item No. 9 :-Refilling the excavated trenches with available stuff in layer of 15 to 20 cm lwith compaction watering etc. complete.

Item No. 10:-Drilling of 150 mm Dia Horizontal Bore ( Gravel packing)

Item No. 11:-150 mm dia threaded iron casing pipe

Item No. 12:-Providing structural steel work in single sections like joists, channels, angles, tees, etc. as per detailed designs and drawings including fixing in position without connecting plates, braces, etc. and one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade, etc. complete. (Bd-C-2/275

Item No 13:-Providing and fixing M.S. chequerred plate flooring of following thickness supported on M.S. angles (25 x 25 x 5 mm size) including welding, cutting and fabricating the plates to the required square or rounding shape, making holes in the plate, including providing and applying 3 coats of anticorrosive paint, etc. complete as directed by Engineer-in-charge.

Item No 14:-Carrying out recuperation/yield test for asserting the dischage of constructed well/excavated profile as directed by engg-in-charge. The test is carried out by drawing down water from the well/profile below normal/subsoil water level upto full depth rise in water level is recoreded. The normal water level/ subsoil water level in the well/profile as well as stainer/suction level at pump as per design of WS scheme shall be recorded prior to the test including cost of all material, overhead, labourers etc ompleted as directed

Item No 15:-Laying and placing in position shrouding material for porous pipe gallery/slotted gallery/well work with all leads and lifts involved including transportation of materials to site of works, screening and washing of materials and placing in position with given section. Complete.(Boulder +Sand filling)

Item No 16:-Providing & fixing in well Steining, 80 mm dia A.C/PVC pipe weep holes 1.5 M c/c staggered, pipe sloping outside well Steining so as to prevent sand coming along with water current including cost of all jointing materials and labour involved with all leads and lifts etc.

Item No. 17:-Taking Trial Bore (Core Bore Sampling) by Calyx machine with TCT/NX to get undisturbed strata samples for investigation in all types of strata soft soil, murum, hard murum with boulders, soft rock, hard rock and quartzite. The item includes all higher and running cost of Calyx machine and back sampling all over burden strata in glass jar and Core samples serially numbered at size in a wooden Core Box, samples to be taken at 1.0 M interval and conveying to the place as directed by Engineer-In-Charge. The diameter of bore in overburden shall be 100 mm and of NX size (50 mm) in other strata. The item shall also include M.S. casing pipe of 2.5 mm thick plate in overburden only and shall be 1.0 M above G.L. with cap over it.

Providing and fixing G.I. pipe railing having 1.0 M height consisting 50 x 50 x 6 mm thick M.S. angles as verticals at 1.5 M c/c and additional posts at every corner with 3 rows of 25 mm dia G.I. pipes of medium class variety as horizontal and painting 3 coats of oil paint over 1 coat of anticorrosive paint of approved colour and shade including cost of all labour, transporting bends to curved shape, etc. complete.

SUBWORK NO 2 : Pumping Machinary 3 BHP ITEM NO. 1Providing, erecting and giving tests of submersible pump set confirming to IS 8034 and motor confirming to IS 9283, with water proof winding and discharge with stainless steel shaft. Mortar suitable for working on 415 V = 10% 3 phase 50 Hz A.C. supply with cable guard, thrush carbon/fible bearing to withstand entire hydraulic thrust with suitable suction strainer, pump should have suitable discharge outlet as per manufacture's design. Antithrust streamlined run and 2 pairs of erection clamps 80 mm width non return valve.Submersible pump 150 mm dia (with bronze impeller upto 8 stages). Submersible pump 150 mm dia (with bronze/ Stainless steel (CF8M) Impeller upto 8 stages). 3 BHP suitable for 34 mtr head & 3102 litres/hr discharge.

ITEM NO. 2 Providing and Fixing L.T. skeleton panel board upto 5 HP. (As per detail sheet attached)

ITEM NO. 3 Supplying and erecting flat flexible 3 core 4 sq mm PVC sheathed submersible type copper cable suitably clamped at fixed intervals with column pipe assembly complete.

ITEM NO. 4 Providing & erecting ISI mark G.I. pipe of following class and dia. including all local and central taxes, octroi, inspection charges, transportation to stores, etc. complete 50 mm dia (heavy) on well

ITEM NO. 5 Providing, supplying and fixing ISI mark CI D/F Reflux valve (non-return valves of following dia including all taxes (central and local), railway freight, inspection charges, unloading from railway wagon, loading into truck, transportation upto departmental store/site, unloading, stacking etc. complete. Reflux valves as per I.S. 5312 part I (1984) a) Without bypass arrangement - PN - 1 50 mm dia

ITEM NO. 6 Providing and fixing double flanged sluice valve confirming for IS-2096/14846 including worn gear arrangements as per test pressure stainles steel spindle, caps including all taxes transportation etc complete. a) Sluice valve - PN - 1 (Without bypass) 50 mm dia

ITEM NO. 7 Lowering, laying and jointing in position following C.I.D/F Reflex valves, Butterfly valves and Sluice valves including cost of all labour jointing material, including nut bolts and giving satisfactory hydraulic testing etc. complete. (Rate for all class of valves.) a) Sluice valve - PN - 1 (Without bypass) 50 mm dia

ITEM NO. 8 Providing and erecting pressure gauge of required capacity complete with syphon tube, isolating cock suitable for 12mm dia GI pipe. Pressure gauge shall be installed as directed, with tapping on rising main pressure gauge (100 mm dia)

ITEM NO. 9 Providing earthing with galvanized iron earth plate size 60 x60 x 0.6 cm with funnel with a wire mesh for watering and brick masonry block C.l. cover complete with all materials, testing & recording the results as per specification no. EA-EP. Plate type Electrode (IS 3043) 1. For pump -2 Nos 1. For panel board - 1No.

ITEM NO. 10 Providing and supplying ISI standard CI Flanged/ S&S specials including all taxes (Central and local), railway freight, insurance, unloading from railway wagon, loading into truck transport to departmental store/site, unloading stacking etc. complete. CI D/F specials i) 80 to 300 mm dia

SUBWORK NO 3 : RISING MAIN ITEM NO. 1 Material Section Providing and supplying in standard lengths ISI mark rigid unplasticised PVC pipes suitable for potable water with solvent cement joints including cost of couplers, as per IS specification no. 4985 / 1988 excluding GST levied by GOI and GOM in all respect, including transportation, freight charges, inspection charges, loading, unloading, conveyance to the departmental stores and stacking the same in closed shed duly protected from sun rays and rains including cost of jointing material i.e. solvent cement, etc. complete (selffit type to be jointed with cement solvent). Proposed Supply Well to Proposed ESR (90 mm PVC 6 Kg/m2)

Providing and supplying ISI standard PVC & GI specials and fittings including transportation to stores/site, loading, unloading charges excluding GST levied by GOI & GOM, etc. complete. 10% of cost of pipes

ITEM NO. 3 Labour Section Excavation for foundation / pipe trenches in earth, soils of all types, sand, gravel and soft murum, including removing the excavated material upto a distance of 50 metres and lifts as below, stacking and spreading as directed, manual dewatering, preparing the bed for foundation and excluding backfilling, etc. complete. Lift 0 to 1.5

ITEM NO. 4 Excavation for foundation / pipe trenches in hard murum and boulders, W.B.M. road including removing the excavated material upto a distance of 50 M beyond the area and lifts as below, stacking and spreading as directed by Engineer-in-charge, normal dewatreing, preparing the bed for foundation and excluding backfilling, etc. complete. Lift 0 to 1.5 M

ITEM NO. 5 Lowering, laying and jointing with P.V.C.pipes and specials of following class and diameter including cost of conveyance from stores to site of works including cost of all labour, material, except cement solvent, rubber ring, as per IS code, etc. complete (with cement solvent joint / ring fit joint). 90 mm Dia.

ITEM NO. 6 Hydraulic testing of PVC pipe line to specified pressure including cost of all materials and labour and water for testing for specified length including cutting, placing end cap making arrangement for filling safe water using reciprocating type pumps which should be able to provide specified test pressure gauges and other necessary equipments, labour, operation charges, etc. required for testing. The rate under this item shall also include cost of retesting, if necessary and reinstating to original position 90 mm Dia.

ITEM NO. 7 Refilling the trenches with available excavated stuff with soft material first consolidation, etc. complete. Total qty = Qty. excavation- Concrete encasing - pipe volume- Murum Bedding Well to ESR

SUBWORK NO 4: RCC ESR 18000 litres Staging Height 12 m ITEM NO.1Designing (aesthetically), and constructing RCC Elevated Service Reservoirs of following capacity with RCC staging consisting of columns, internal and external bracings spaced vertically not more than 4.5 meters centre to centre for E.S.R. having capacity 500 m3 & not more than 6 m c/c for E.S.R.having capacity above 500 m3 including excavation in all types of strata, foundation concret, cement plaster with water proofing compound to the inside face of the container including refilling disposing of the surplus stuff within a lead of 50 meters, all labour and material charges including lowering, laying, erecting, hoisting and jointing of pipe assembly of inlet, outlet, washout, overflow and bypass arrangements as per departmental design. providing and fixing accessories such as Stainless steel ladder inside and M.S. ladder with G.I. railing outside, C. I. manhole frame and covers water level indicatiors, lightening conductor, G. I. pipe railing around walk way and top slab, providing spiral staire case from ground level to roof level, M.S.Grill gate of 2 Mtrs height with locking arrangement, B.B. masonry chambers for all valves, ventilating shafts, providing and applying three coats of acrylic emulsion with silicon additives paint to the structure including roof slab and epoxy paint to internal surface & anti-termite treatment for underground parts of the structures and giving satisfactory water tightness test as per I.S. code, The job to include painting the name of the scheme and other details on the reservoir as per the directions of Engineer-in-charge. The design of the structure be in accordance with relevant I.S. specification (I.S. 3370 - 1965 or revised.) The design shall satisfy the stipulations as per I.S. 1893 - 1984 and I.S. 13920 / 1993 for seismic force and I.S. - 11682 / 1985 for R.C.C. staging of overhead tanks. For design having more than 6 columns, provision of internal bracing is obligatory. External bracings is also obligatory. The entire structure shall be in M-300 mix only. Plain round mild steel bars grade-I conforming to I.S. 432 part-I or high yield strength deformed bars conforming to I.S. 1786 or I.S. 1139 shall be used, grade-II mild steel bars will not be allowed. Irrespective of the type of foundation proposed in the design, one set of bracing be provided at the ground level. These rates include providing M.S. ladder for E.S.R.s upto 2 lakh litres capacity and providing spiral staircase for E.S.R. above 2 lakh litres capacity. Staging shall have to be designed with stresses of M-200 concrete for ESR. However all RCC construction should be done in M-300. These rates are including the cost of uplift pressure if any and entire dewatering during execution. In case of water logging area where water is stretch at shallow depth, extra provision of dewatering shall be made as per site condition. All conditions given in the Member Secretary's Circular No. MJP / TS-I / 350 / 1668 dt. 2-8-97 and MJP / S-I / 350 / 2127 dt. 13-7-99 shall be strictly followed and additional cost, if any, due to these conditions is included in the rates mentioned below. 75% part rate shall be payable for reinforcement concrete and plastering items of containers of E.S.R. till satisfactory hydraulic testing for water tightness is given; and till that work shall be treated as incomplete. The rates indicated in the table are excluding the cost of pipes, specials and valves required for inlet, outlet, washout, overflow and bypass arrangement. The scope of work, however, includes cost of erecting, laying and jointing of pipes and valves including cost of jointing materials upto 5 M beyond outer face of outermost column. For ESR upto 500 cum capacity C.I. double flanged pipes upto 300 mm dia shall be provided and C.I. specials shall be used. For ESR above 500 cum capacity C.I./M.S. pipe assembly with minimum 8 mm thickness upto 500 mm dia and minimum 10 mm thickness above 500 mm dia can be used with proper anti-corrosive epoxy treatment from inside and outside. Below mentioned rates are for foundations with individual footing with bearing capacity of 20 tonnes per square metre. For raft foundations, these rates shall be increased by 7.5% where safe bearing capacity (SBC) is 5 MT per sqm and by 5% where SBC is more than 5 MT/sqm and upto 10 MT/sqm. This % of 5% or 7.5% is applicable for estimation of amount of lumpsum item of ESR. For extra item due to change from individual foundation to raft, actual increase in concrete and steel be paid as per relevant DSR item. The rate shall be increased by 30% for bearing piles upto depth of 10 M and for further increased in depth by 5 M each, it shall be increased by another 10%. These rates are applicable where raft is not feasible. For pile foundations sulphate resistant cement shall only be used. Single pile for the column is not permitted, group of piles shall be designed with pile cap for each column of ESR. The rates are applicable for staging height of 12 M. These rates shall be increased or decreased for per metre variation in this staging height as below: Following rates are for seismic zone III. For zone IV, these rates shall be increased by 5% and for zone II, these rates shall be decreased by 5%. Concerned Executive Engineer shall confirm the seismic zone for the scheme from seismic zones plan before estimation and adopt appropriate rates as per actual seismic zones. (Seismic maps attached in this CSR). RCC ESR Capacity 18000 litres 12 m staging Height, 3 m tank height Cost of 18000Ltr Total cost for 52000 Litres @ 12 m staging height For raft foundations, these rates shall be increased by 7.5% where safe bearing capacity (SBC) is 5 MT per sqm and by 5% where SBC is more than 5 MT/sqm and upto 10 MT/sqm. This % of 5% or 7.5% isapplicable for estimation of amount of lumpsum item of ESR. Concrete Qty of 18000 Lit = 27.4 cum Metal 0.9 = 24.66Cum @ Sand 0.45 = 12.33 Cum @ 21.45 Steel Difference (2.14x97206)-(2.14x84527)=208020.84-180887.78=27133.00 Total cost for 18000 Litres @ 12 m staging height

ITEM NO.2 Providing & supplying ISI standard CI double flanged pipes excluding GST levied by GOI & GOM in all respect including railway freight, insurance , unloading from railway wagon, loading into truck transport to stores, unloading etc. complete as directed by Engineer-in-charge. Inlet 80mm dia.CI.D./F pipes

Outlet 80 mm dia.CI.D./F pipes

Overflow 80mm dia.CI.D./F pipes

Washout 80 mm dia.CI.D./F pipes

ITEM NO.3 Providing And supplying ISI standard CI Flanged /s &S Specials Including all Statutory Duties &taxes such as GST Levied by GOI &GOM in all Respect.Railway Freight Insurance Unloading From Railway wagon,Loading into truck Transport to Departmental Store /Site Unloading Stacking etc Complete D/F Specials 300 D/F Specials Upto and Including 150 mm 80 mm to 300 mm dia

ITEM NO.4 Providing double flange sluice valve confirming for IS- 14846 including worn gear arrangements as per test pressure, stainless steel spindle, caps, including inspection charges, transportation upto departmental store, unloading, stacking excluding GST levied by GOt & GOM in all respect etc. complete Sluice valves PN-1 without bye-pass arrangement 80 mm dia. Sluice valve - Outlet/Distribution

80 mm dia. Sluice valve - Inlet/Bypass

80 mm dia. Sluice valve - Washout

SUBWORK NO 5 : DISTRIBUTION SYSTEM ITEM NO.1 Material Providing and supplying in standard lengths ISI mark rigid unplasticised PVC pipes suitable for potable water with solvent cement joints including cost of couplers, as per IS specification no. 4985 / 1988 excluding GST levied by GOI and GOM in all respect, including transportation, freight charges, inspection charges, loading, unloading, conveyance to the departmental stores and stacking the same inclosed shed duly protected from sun rays and rains including cost of jointing material i.e.solvent cement, etc. complete (self fit type to be jointed with cement solvent). Working Pressure 4 kg/cm2 75 mm

90 mm

Providing and supplying ISI standard PVC & GI specials and fittings including transportation to stores/site, loading, unloading charges excluding GST levied by GOI & GOM, etc. complete. 10% of cost of pipes

ITEM NO.2 Providing ISI mark G.I. pipe of following class and dia. excluding GST levied by GOI & GOM in all respect, inspection charges, transportation to stores, etc. complete as per IS-1239/2004. Note : One coupler shall be provided with each full length of pipe cost of which is included in rates below. 80 MM DIA MEDIUM CLASS

100 MM DIA MEDIUM CLASS

ITEM NO.3 Providing double flange sluice valve confirming for IS- 14846 including worn gear arrangements as per test pressure, stainless steel spindle, caps, including inspection charges, transportation upto departmental store, unloading, stacking excluding GST levied by GOt & GOM in all respect etc. complete.Without by pass arrangement - PN-1. 65 mm sluice valve

ITEM NO.4 LABOUR Excavation for foundation / pipe trenches in hard murum and boulders, W.B.M. road including removing the excavated material upto a distance of 50 M beyond the area and lifts as below, stacking and spreading as directed by Engineer-in-charge, normal dewatering, preparing the bed for foundation and excluding backfilling, etc. complete. (Bd A-3/259) Lift 0 to 1.5

ITEM NO.5 Excavation for foundation / pipe trenches in hard murum including removing the excavated material upto a distace of 50 M and lifts as below, stacking and spreading as directed by Engineer-in-charge, normal dewatering, preparing the bed for foundation and excluding backfilling, etc. complete. Lift 0 to 1.5

ITEM NO.6 Excavation for foundation / pipe trenches in soft rock and old cement and lime masonry foundation asphalt road including removing the excavated material upto a distance of 50 M beyond area and lifts as below, stacking as directed by Engineer-in-charge, normal dewatering, preparing the bed for foundation and excluding backfilling, etc. complete. Lift 0 to 1.5

ITEM NO.7 Excavation for foundation / pipe trenches in hard rock and concrete road by chiselling, wedging, line drilling by mechanical means or by all means other than blasting including trimming and levelling the bed, removing the excavated material upto a distance of 50 metres beyond the area and lifts as below, stacking as directed by Engineer-in-charge, normal dewatering, excluding backfilling, etc. complete by all means. (Bd-A-6/259) Lift 0 to 1.5

ITEM NO.8 Filling in plinth and floors murum bedding in trenches with approved murum from excavated materials from foundation 15cm to 20cm layers including watering and compaction complete. Murum selected from excavated stuff

ITEM NO.9 Lowering Laying and jointing with P.V.C pipes and specials of following class and diameter including cost of conveyance from source to site of works including cost of all labour,material,except cement solvent,rubber ring,as per IS code etc.complete (with cement solvent joint/ring fit joint) Working Pressure 4 kg/cm2 75 mm

90 mm

ITEM NO.10 Hydraulic testing of PVC pipe line tospecified pressure including cost of allmaterials and labour and water for testing forspecified length including cutting, placing endcap making arrangement for filling safe waterusing reciprocating type pumps which shouldbe able to provide specified test pressuregauges and other necessary equipments,labour, operation charges, etc. required fortesting. The rate under this item shall alsoinclude cost of retesting, if necessary andreinstating to original position. Working Pressure 4 kg/cm2 75 mm

90 mm

ITEM NO.11 Lowering, laying and jointing G. I. pipes and specials of following class and diameter including conveyance from stores to site of works, all labour, etc. complete either underground or in vertical position, as directed by Engineer-in-charge. Considering Nalla / Road Crossing 80 MM DIA MEDIUM CLASS

100 MM DIA MEDIUM CLASS

ITEM NO.12 Lowering, laying, jointing in position following CI/DF Reflux, butterfly valves and sluice valves including cost of all labors jointing material including nutbolts and giving satisfactory hydraulic testing etc complete ( Rates for all class of valves ) 65 mm sluice valve

ITEM NO.13 Providing and fixing C.I. road box including loading, unloading and carting to site of work including all necessary excavation in all types of strata and fixing in murum packing, etc. complete 100 mm x 225 mm (20 kg)

ITEM NO.14 Providing and laying in situ Cement Concrete M-15 of trap/ granite / quartzite / gneiss metal for foundation and bedding including bailing out water, form work, compaction, curing, etc. complete. (Cement 5.90 bags / cum)Spec. No. - Bd E /1 Page No. 287 and B-7, Page No. 38

ITEM NO.15 Refilling the trenches with available excavated stuff with soft material first over pipeline and then hard material in 15 cm layers with all leads and lifts including consolidation, surcharging, etc. complete. Net volume of refilling

ITEM NO.16 Providing and making solid support for FHTC (Functional Household Tap Connection)with c.c. stand 1:3:6 mix base platform size 1.10m x 0.95 m + width 0.20 m + depth below ground level 0.10 x 0.20 x deep wailing with 110 mm dia. x 0.65 m + deep stand in c.c 1:3:6 as per drawing including centering , curring , finishing etc. Completed painting in oil paint in various colours as per directed by engineer incharge.

SUBWORK NO: 6 RCC CATTLE TROUGH QTY FOR 2 NOS Item 1: Excavation for foundation / pipe trenches in earth, soils of all types, sand, gravel and soft murum, including removing the excavated material upto a distance of 50 metres and lifts as below, stacking and spreading as directed, manual dewatering, preparing the bed for foundation and excluding backfilling, etc. complete. Lift 0 to 1.5 M Excavation for cattle trough

Excavation for connecting pipe

Item No 2: Providing dry trap / granite / quartzite / gneiss, rubble stone soling in 15cm to 20 cm thick layers (including hand packing and compacting), etc. complete.

Item No.3: Filling in plinth and floors/ trenches with contractor's murum in 15cm to 20cm layers including watering and compaction complete.

Item No.4: Providing and laying in situ following grades of Plain Cement concrete of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including normal dewatering, form work, compaction and curing, etc, complete. Use of L & T, A.C.C., Ambuja, Birla Gold, Manikgad Rajashree, etc cement is permitted. PCC M-150

Item No.5: Providing and laying in situ Cement concrete of trap/granite/quartzite/ gneiss metal for RCC work in foundation like raft, grillage, strip foundation and footing of RCC columns and steel stanchions including normal dewatering, 'plywood form work,bully/steel propups propups, compaction, finishing and curing, etc, complete. (By weigh batching and mix design for M-250 and M-300 only. Use of L & T, A.C.C., Ambuja, Birla Gold, Manikgad, Rajashree etc. cement is permitted.) (excluding M.S. or Tor reinforcement) In RCC M-150 bottom slab

Item No.6 Providing and casting in situ Cement Concrete of trap/granite/quartzite/ gnesis metal of approved quality for RCC work as per detailed drawings and designs or as directed by including normal dewatering, centering, 'plywoodEngineer in charge formwork, bully/steel prop-ups, compaction, finishing the formed surfaces with CM 1:03 of sufficient minimum thickness if special finish is to be provided and curing, etc. complete. (By weigh batching and mix design for M-250 and M-300 only. Use of L&T, A.C.C., Ambuja, Birla Gold, Manikgad, Rajashree, etc. cement is permitted. (excluding M.S, or Tor reinforcement In RCC M-150 Long Wall for cattle trough

Long Wall

Cross Wall

Guard Ward to cattle trough platform

Cross Guard Wall

Back Guard Wall

ITEM NO.7 Providing and fixing in position steel bar reinforcement of various diameters for RCC piles, caps, footings, foundations, slabs, beams, columns, canopies, staircases, newels, chajjas, lintels, pardies, copings, fins, arches, etc. as per detailed designs, drawings and schedules; including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required, etc. complete (including cost of binding wire). (Bd-F- 17/306) b) To r Steel b) To r Steel

Item 8: Providing and supplying Blue MDPe pipes conforming to ISO 4427:1996 manufactured from virgin resin PE 80 Food grade compounded Raw Material having Blue colour only assurance certificate from quality agencies like WRC /CIPET (India)with quality. /DVGM /KIWA /SPGN etc. for usage in Drinking Water system. The cost shall include testing of all materials, Inspection charges, transportation up to store, transit insurance, loading, as specified and directed, unloading, stacking excluding GST levied by GOI & GOM in all respect, etc. complete as specified and directed. 32mm dia MDPE Pipe for water supply to cattle trough

Item No.9: Providing, lowering, laying MDPE specials Including tap connection etc. complete as directed. Specials required for making connctions and fittings including tap, drainage arrangement

SUBWORK NO: 7 Miscellaneous Work ITEM NO.1 Commisioning running and maintaining the scheme to quantities, rate capacity, including manning necessory personnel such as operator, valveman, etc, as pr requirements of the scheme and who should also administer chemical dose for a period of one month for individual scheme together with training of personnel spared by MJP/ Local Body and handling over the scheme to Local Body after completion of the above period as directed by Engineer - in charge. For single village (three Month)

Providing and erecting chain linkfencing 1.6M. height with G.I.chain link of size 50x50 mm, 8 gauge thick and fixed 75mm above ground level on vertical M.S.Angles of 40x40x6mm size,includind excavating pits for foundation and embeddedin C.C.block of 1:4:8 mix of size 450x450x670 mm. at 1.75M.c/c with iron bar 16mm dia as hold fast including welding link with angle frame at 30cm c/c with nuts and bolts and horizontal M.S. Angles at top and bottom of 25x25x5 mm size and vertical M.S. flat 35x5 mm and 25x5 mm horizontal including cross support of 40x40x6 mm angles both side at every corneror bend embedded in concrete blocks of1:4:8 of size 450x450x670 mm including 3coats of oil painting etc. complete

Providing and fixing M.S. gate 2.5 M wide for compound with 40 mm dia G.I. pipe, approved grill work, RCC M-150 side pillars of 25 cm x 40 cm x 2.5 M height, its foundation, finishing, painting, etc.

Providing and fixing board displaying information such as "Name of work, Tender cost,Name of Contractor, Work completion and liability periodetc" having rectangular shape of 1.20mx0.90m size made up of 4mm aluminum composite pannel sheet with 0.5 mm skin thickness on either side bonded withi (TypeXIMicro prismatic grade sheeting) having pressure sensitive adhesive. Retroreflective sheeting with specified background, borderand back side retoreflective symbols,letters,numerals,arrow as per IRC:67-2012 Table No 8.3,on Sangle of size 35x35x3mm frame with properly cross M.S. braced M.S.angles of size 35mmx35mmx3mm duly paint edincluding Two M.S.angle iron post sof size65mmx65mmx6mm,3.65 m long painted with alternate black and white bands of 25cm width includinga Ilifixtures etc and fixing the board sin1:4:8 concrete block of size 60cmx60cmx75cm including, excavation, refilling, (TypeXIMicro prismatic grade sheeting) shall have 10 years written warranty from the manufacturer including the Digitally Printed area swith Lat ex nrinting technology with sheeting PWD CSR 2021-22 It. No.58.82 Page No. 369

SUBWORK NO: 8 FUNCTIONAL HOUSEHOLD TAP CONNECTION (FHTC) Providing and making UPVC/MDPE pipe consumer service connection on Distribution main by drilling hole with suitable means , including all labour , UPVC/MDPE Pipe of required length with or without Road crossing as described below, including cost of specials like Saddle/Clamp Saddle of suitable material, and diameter suitable for Distribution main, 15mm /20mm/ 25mm respective Dia Heavy duty Brass/Polyprophylyne(Twin Jacketed ) Ferrule , Male and Female thread adapter Elbow, Bends,couplers ,Tees, Clamps of suitable material and sundry materials as per requirment, including providing and fixing medium duty 15.mm brass bib tap, GI casing pipe of suitable diameter of 32mm/ 40mm/ 50mm respectively of required length for Road crossing, including requird labour for excavation in all types of strata up to the depth of 0.75m or as per site requirement,all types of plumbing fittings, refilling , Closing the water supply in that area, dewatering, hydraulic testing and restarting the water supply ,transportation of material etc. complete as directed by Engineer in Charge. A) Household Connection without water meter (Comression Saddle+ISI Mark Ferrul) for HDPE & PVC pipe For MDPE/UPVC Pipe Service Connection on Disribution main (Without Road Crossing) For 15 mm Service connection( Road Crossing)

For 15 mm Service connection