Rashtriya Chemicals And Fertilizers Limited Tender

SAME AS ITEM NO. 3, BUT LIFT FROM 1.5 M TO 3.0 M

SAME AS ITEM NO. 1, BUT IN HARD ROCK AS DEFINED IN IS:1200

SAME AS ITEM NO. 5,BUT LIFT FROM 1.5 M TO 3.0 M

REMOVAL AND CARRIAGE OF SURPLUS EXCAVATED EARTH, DEBRIS, DISMANTLED MATERIALS ETC., FROM THE SITE OF WORK TO OTHER AREAS ANYWHERE WITHIN THE FACTORY UPTO 3 KM / PLANT BATTERY LIMITS BEYOND THE INITIAL LEAD OF 50 M AND SPREADING AND LEVELING THE SAME IN LAYERS NOT EXCEEDING 20 CM THICKNESS INCLUDING LOADING AND UNLOADING AS PER THE DIRECTION OF ENGINEER-IN- CHARGE.

PROVIDING AND LAYING DRY / TRAP / GRANITE / QUARTZITE / GNEISS RUBBLE STONE SOLING 15 TO 20 CM THICK INCLUDING HAND PACKING & COMPACTING ETC. COMPLETE AS DIRECTED.

PROVIDING AND CONSTRUCTING SECOND CLASAS BURNT BRICK MASONRY IN CEMENT MORTAR 1:6 (1 CEMENT : 6 COARSE SAND) INCLUDING STRIKING JOINTS, WATREING, SCAFFOLDING ETC. COMPLETE IN SUBSTRUCTURE AND SUPERSTRUCTURE AT ALL HEIGHTS AS DIRECTED ETC COMPLETE

PROVIDING AND CONSTRUCTING MASONRY IN AUTOCLAVED AREACLAVED CONCRETE BLOCK OF APROVED MANUFACTURER CONFIRMING TO RELAVENT IS CODE OF APPROVED SIZE IN EXTRA FINE JOINTING MORTAR OF FIXOBLOCK OF IN SUPERSTUCTURE INCLUDING, STRIKING JOINTS,RACKING OUT JOINTS WATERING AND SCAFFOLDING ETC.COMPLETE

PROVIDING AND LAYING PLAIN CEMENT CONCRETE M-15 (1 CEMENT: 2 FINE AGGREGATE :4 GRADED STONE AGGREGATE 20 MM NOMINAL SIZE), MANUAL / MACHINE MIXED AND MANUAL / MECHANICALLY VIBRATED IN FOUNDATIONS, PLINTH, UNDER FLOORS, SCREEDING AS PER EIC ETC., INCLUDING ALL NECESSARY COST OF CENTRING AND SHUTTERING, COVER BLOCKS & CURING ETC. COMPLETE.

PROVIDING AND LAYING PLAIN CEMENT CONCRETE M-10 (1 CEMENT:3 FINE AGGREGATE :6 GRADED STONE AGGREGATE 20 MM NOMINAL SIZE), MANUAL / MACHINE MIXED AND MANUAL / MECHANICALLY VIBRATED IN FOUNDATIONS, PLINTH, UNDER FLOORS, SCREEDING AS PER EIC ETC., INCLUDING ALL NECESSARY COST OF CENTRING AND SHUTTERING, COVER BLOCKS & CURING ETC. COMPLETE.

PROVIDING AND LAYING IN SITU CEMENT CONCRETE OF GRADE M-25 OF TRAP/ GRANITE /QUARTZITE/ GNEISS METAL (USING 20 MM NOMINAL GAUGE GRADED STONE AGGREGATE) FOR R.C.C. WORK IN FOUNDATIONS LIKE RAFT, STRIP FOUNDATIONS, GRADE SLAB, GRILLAGE AND STEEL STANCHIONS ETC. INCLUDING MAKING ARRANGEMENT FOR BAILING OUT OF ANY SEEPAGE WATER UNDERNEATH, DEWATERING, FORMWORK, COVER BLOCKS, COMPACTION AND CURING (EXCLUDING REINFORCEMENT AND STRUCTURAL STEEL) COMPLETE INCLUDING CENTERING, SHUTTERING, FAIR FINISH ETC. COMPLETE IN ALL RESPECTS AS PER DIRECTION OF ENGINEER-IN-CHARGE. (MINIMUM CEMENT CONTENT SHALL NOT BE LESS THAN 410 KG/CUM.)

PROVIDING AND LAYING IN SITU CEMENT CONCRETE OF GRADE M-25 OF TRAP/ GRANITE /QUARTZITE/ GNEISS METAL (USING 20 MM NOMINAL GAUGE GRADED STONE AGGREGATE) FOR R.C.C. WORK IN PLINTHS BEAM, LINTELS, COLUMNS, PEDETSALS, WALLS/PARDIS ETC. INCLUDING MAKING ARRANGEMENT FOR BAILING OUT OF ANY SEEPAGE WATER UNDERNEATH, DEWATERING, FORMWORK, COVER BLOCKS, COMPACTION AND CURING (EXCLUDING REINFORCEMENT AND STRUCTURAL STEEL) COMPLETE INCLUDING CENTERING, SHUTTERING, FINISHING SURFACES TO GIVE A SMOOTH AND EVEN SURFACE OR ROUGHENING IF SPECIAL FINISH TO BE PROVIDED ETC. COMPLETE IN ALL RESPECTS AS PER DIRECTION OF ENGINEER-IN-CHARGE. (MINIMUM CEMENT CONTENT SHALL NOT BE LESS THAN 410 KG/CUM.)

PROVIDING AND LAYING IN SITU CEMENT CONCRETE OF GRADE M-25 OF TRAP/ GRANITE /QUARTZITE/ GNEISS METAL (USING 20 MM NOMINAL GAUGE GRADED STONE AGGREGATE) FOR R.C.C. WORK IN SLABS, LANDINGS, CHAJJA ETC. INCLUDING MAKING ARRANGEMENT FOR BAILING OUT OF ANY SEEPAGE WATER UNDERNEATH, DEWATERING, FORMWORK, COVER BLOCKS, COMPACTION AND CURING (EXCLUDING REINFORCEMENT AND STRUCTURAL STEEL) COMPLETE INCLUDING CENTERING, SHUTTERING, FINISHING SURFACES TO GIVE A SMOOTH AND EVEN SURFACE OR ROUGHENING IF SPECIAL FINISH TO BE PROVIDED ETC. COMPLETE IN ALL RESPECTS AS PER DIRECTION OF ENGINEER-IN-CHARGE. (MINIMUM CEMENT CONTENT SHALL NOT BE LESS THAN 410 KG/CUM.)

PROVIDING AND FIXING STEEL BAR REINFORCEMENT (TMT FE 500 ISI MARKED STEEL) OF VARIOUS DIAMETERS (CONFORMING TO IS CODE) FOR R.C.C. FOOTINGS, FOUNDATIONS, SLABS, BEAMS, COLUMNS, STAIRCASE, NEWELS, CHAJJAS, LINTELS, PARDIS, COPINGS, ARCHES ETC. AS PER DETAILED DESIGNS, DRAWINGS AND SCHEDULES INCLUDING CUTTING, BENDING, HOOKING THE BARS BINDING WITH WIRES, COVER BLOCK SUPPORTING, TACK WELDING AS REQUIRED ETC. COMPLETE. NO EXTRA PAYMENT SHALL BE MADE FOR 18 SWG ANNEALED BINDING WIRES, CHAIRS.

PROVIDING AT ALL HEIGHTS 12 MM THICK CEMENT PLASTER ON BRICK WORK, EXPOSED SURFACES OF RCC LINTELS, BEAMS, ETC., COMPLETE IN ALL RESPECTS AND AS DIRECTED WITH CEMENT PLASTER MIX : 1:4(1 CEMENT : 4 PACKED BAG SAND), INCLUDING NECESSARY SCAFFOLDING, CURING ETC. COMPLETE.

PROVIDING EXTERNAL SAND FACED CEMENT PLASTER IN CEMENT SAND MORTAR 1:4 (1CEMENT:4 PACKED BAG SAND) USING PACKED BAG SAND IN TWO LAYERS INCLUDING PROVIDING BASE COAT OF 12 TO 15 MM THICK MIXING APPROVED WATER PROOFING COMPOUND TO THE FIRST COAT OF PLASTER AND KEEPING BASE COAT ROUGH TO RECEIVE SAND FACED TREATMENT OF 6 TO 8 MM THICK INCLUDING SCAFFOLDING,CURING ETC. COMPLETE.

PROVIDING AND LAYING TELEPHONE BLACK / AMBA WHITE / CADBURY BROWN / RBI RED / OCEAN BROWN GRANITE STONE OF 15 TO 20 MM THICK FOR DOOR FRAME / DADO / WINDOW BOXING / PLATFORM OTTA ETC. ON C.M. 1:6 INCLUDING FILLING JOINTS WITH POLYMER BASE FILLER NOSING THE SHARP EDGES WHEREVER NECESSARY, CURING, ETC. COMPLETE..

PROVIDING AND LAYING MIRROR / GLOSSY / MATT FINISH VITRIFIED TILES OF SOMANY / RAK / KAJARIA / NITCO / JHONSON (300 MM X 300 MM OR 590-600 MM X 590-600 MM OR GREATER SIZED AS DIRECTED BY EIC) OF APPROVED QUALITY, SHADE AND PATTERN FOR FLOORING IN REQUIRED POSITION LAID ON A BED OF CEMENT MORTAR 1:4 INCLUDING CEMENT FLOAT JOINT FILLING WITH WHITE/COLOUR CEMENT SLURRY, CLEANING, CURING INCLUDING MAKING EXISTING FLOOR SUITABLE TO FIX NEW TILES IN PROPER LEVEL ETC. COMPLETE AS INSTRUCTED BY EIC.

PROVIDING AND LAYING MIRROR / GLOSSY / MATT FINISH CERAMIC TILES OF SOMANY / RAK / KAJARIA / NITCO / JHONSON.(300 MM X 300 MM OR 590-600 MM X 590-600 MM OR GREATER SIZED UPTO 1000 MM AS DIRECTED BY EIC) OF APPROVED QUALITY, SHADE AND PATTERN FOR DADO AND SKIRTING IN REQUIRED POSITION LAID ON A BED OF CEMENT MORTAR 1:4 INCLUDING CEMENT FLOAT JOINT FILLING WITH WHITE/COLOUR CEMENT SLURRY, CLEANING, CURING INCLUDING MAKING EXISTING FLOOR SUITABLE TO FIX NEW TILES IN PROPER LEVEL ETC. COMPLETE AS INSTRUCTED BY EIC.

PROVIDING AND LAYING ANTISKID CERAMIC TILES OF APPROVED QUALITY OF SIZE 30 CM X 30 CM FOR ANTISKID FLOORING IN REQUIRED POSITION LAID ON A BED OF 1:4 CEMENT MORTAR INCLUDING CEMENT FLOAT, FILLING JOINT WITH CEMENT SLURRY CLEANING CURING ETC. COMPLETE.

PROVIDING WATER PROOF BEDDING FOR FLOORING OF BATH AND WC 25 MM THICK IN C.M. 1:3 INCLUDING USING APPROVED WATER PROOFING COMPOUND IN SPECIFIED PROPORTION AS PER MANUFACTURERS SPECIFICATIONS FOR PER BAG OF CEMENT INCLUDING LEVELING, CURING INCLUDING PONDING TEST ETC. COMPLETE.

METAL FRAMED SUSPENDED CEILING (SEAMLESS): MAIN SYSTEM: METAL FRAMED SUSPENDED CEILING COMPRISES OF G.I PERIMETER CHANNEL HAVING 0.55MM THICKNESS, TWO UNEQUAL FLANGES OF 20 AND 30MM AND WEB OF 27MM IS FIXED TO SURROUNDING WALLS / PARTITION USING NYLON SLEEVES AND SCREWS AT 450MM CENTERS. THEN INTERMEDIATE CHANNEL (0.91MM THICK) HAVING TWO EQUAL FLANGES OF 15 MM. EACH AND A WEB OF 45MM IS SUSPENDED FROM THE SOFFIT AT 1220 MM CENTER WITH CEILING ANGLE OF WIDTH 25MM X 10 MM X 0.55 MM THICK, FIXED TO SOFFIT AT 1220MM CENTRE WITH G.I CLEAT AND STEEL EXPANSION FASTENERS. CEILING SECTION OF 0.55MM THICKNESS HAVING KNURLED WEB OF 50.5 MM AND FLANGES OF 26MM EACH WITH LIPS OF 10.5MM ARE THEN FIXED TO THE INTERMEDIATE CHANNEL WITH CONNECTING CLIPS ACROSS TO THE INTERMEDIATE CHANNEL, AT 457MM CENTERS. 8MM THICK SQUARE/TAPERED EDGE HILUX BOARDS OR EQUIVALENT ARE THEN SCREW FIXED ACROSS THE CEILING SECTIONS WITH 25MM LONG SELF DRILLING & TAPPING SCREWS HAVING PHILLIPS HEAD WITH UNDER HEAD CUTTER, FOR FIRST AND SECOND LAYER RESPECTIVELY, AT 200MM CENTERS. JOINTING AND FINISHING: THE JOINTS OF THE FACE BOARDS ARE FINISHED WITH SPECIALLY FORMULATED JOINTING COMPOUND AND 48MM WIDE FIBRE TAPE TO PROVIDE SEAMLESS FINISH. CEMENT PRIMER (OIL BASED) TO BE PROVIDED ON ENTIRE SURFACE BEFORE PUTTY/ PAINTING. NOTE:G.I. PERIMETER CHANNEL AND SUPPORTING MATERIALS ARE TO BE PROVIDED TO MAKE ANY OPENING FOR LIGHT FITTINGS, DIFFUSERS ETC. AND SHOULD BE SUPPORTED PROPERLY TO MAINTAIN THE INTEGRITY OF THE CEILING, AND SHOULD BE CHARGED EXTRA.

SUPPLYING, FITTING & FIXING IN POSITION FULLY OR PARTLY GLAZED SINGLE LEAF ANODIZED ALUMINUM DOORS OF APPROVED SHADE MADE UP FROM ALUMINIUM EXTRUDED SECTIONS GLAZED WITH 5.0 MM THICK PLAIN GLASS FIXING WITH SPECIAL GASKET, BEADING, LOCK & ALL NECESSARY FIXTURES AND FASTENINGS ETC. COMPLETE AS PER SPECIFICATIONS, DRAWINGS AND DIRECTION OF ENGINEER-IN-CHARGE. (DETAIL MATERIAL SPECIFICATION WILL BE AS FOLLOWS)I) 15 TO 16 GAUGE THICK AL SECTIONS. (DOOR BOTTOM RAIL 95X44 MM, LOCK RAIL 50X44 MM, TOP & VERICAL RAIL 47X44 MM) II) ALUMINUM ANGLE-16 GAUGE III) 6 MM THICK PLY WOODS/3.5 MM THICK HARDNER SHEET IV) 28 GAUGE ALUMINUM SHEET.

PROVIDING & FIXING 30 MM THICK SINGLE LEAF SOLID CORE FLUSH DOOR WITH APPROVED SHADE LAMINATE (1 MM) FINISH INCLUDING NECESSARY HARDWARE, FITTINGS & FIXTURES LIKE CYLINDRICAL DOOR LOCK, CHROMIUM PLATED HANDLES ON BOTH SIDES, PVC DOOR STOPPER, BRASS MAKE ISI MARKED HYDRAULIC DOOR CLOSER, POLISH TO ALL EXPOSED SURFACES, EDGES, ETC. COMPLETE AS PER DETAIL DRAWING. IF REQUIRED, THE DOOR SHALL HAVE 2' X 3' (OR AS DIRECTED) 5 MM THK. PLAIN GLASS AT TOP FIXED WITH BEADING PATTI ALL AS SPECIFIED AND AS DIRECTED.

PROVIDING AND FIXING FIBER GLASS REINFORCED POLYSTER DOOR SHUTTER 35 MM THICK WITHOUT VENTILATOR INCLUDING CHROMIUM PLATED FIXTURES AND FASTENING WITH CHROMIUM PLATED HANDLES ON BOTH SIDES, ETC COMPLETE.

PROVIDING AND FIXING WALL HUNG / FLOOR MOUNTED EUROPEAN TYPE WHITE GLAZED EARTHENWARE WATER CLOSET PAN OF OF PARRYWARE / HINDWARE/ JAQUAR/CERA MAKE WITH ITS FITTINGS, 4" DIA. PVC BEND PIPE, M.S.BRACKETS, SOFT CLOSER SEAT, GROHE MAKE PNEUMATIC FLUSH TANK, 2 WAY BIB COCK WITH HEALTH FAUSCET, ETC. WITH CHROMIUM PLATED BRASS HINGES AND RUBBER BUFFERS INCLUDING UPVC AND VENT PIPE UP TO THE OUTSIDE FACE OF WALL WITH FITTINGS PIPE, BRACKETS FOR FIXING CISTERN 32 MM DIA. UPVC FLUSH PIPE WITH FITTINGS AND CLAMPS, 20 MM DIA. UPVC OVERFLOW PIPE, MOSQUITO PROOF COUPLINGS, WITH WATER JET AND FITTING INCLUDING CUTTING AND MAKING GROOVE TO THE WALLS AND FLOORS TESTING ETC. COMPLETE SO AS TO MAKE IT FIT TO USE.

PROVIDING AND FIXING WHITE GLAZED EARTHENWARE WASH HAND BASIN OF 55CM. X 40 CM. SIZE INCLUDING COLD WATER PILLAR TAP/COLD AND HOT WATER PILLAR TAP BRACKETS, RUBBER PLUGS AND BRASS CHAIN, STOP TAP AND NECESSARY PIPE CONNECTIONS INCLUDING P.V.C. WASTE PIPE AND TRAP UP TO THE OUTSIDE FACE OF THE WALL. MAKING GOOD THE DAMAGED SURFACE, TESTING ETC. COMPLETE.

PROVIDING, LAYING AND FIXING C.P.V.C. PIPE OF 15MM DIA. WITH FITTINGS SUCH AS BENDS, TEES, REDUCERS, CLAMPS, ETC. INCLUDING NECESSARY EXCAVATION, TRENCH FILLING ETC. COMPLETE. INCLUDING REMOVING EXISTING PIPE LINE IF NECESSARY AND CONVEYING AND STACKING THE SAME AS DIRECTED ETC. COMPLETE.REMOVED SCRAP PIPE SHALL BE TAKEN OUT BY CONTRACTOR

PROVIDING, LAYING AND FIXING C.P.V.C. PIPE OF 20MM DIA. WITH FITTINGS SUCH AS BENDS, TEES, REDUCERS, CLAMPS, ETC. INCLUDING NECESSARY EXCAVATION, TRENCH FILLING ETC. COMPLETE. INCLUDING REMOVING EXISTING PIPE LINE IF NECESSARY AND CONVEYING AND STACKING THE SAME AS DIRECTED ETC. COMPLETE.REMOVED SCRAP PIPE SHALL BE TAKEN OUT BY CONTRACTOR

PROVIDING, LAYING AND FIXING C.P.V.C. PIPE OF 25MM DIA. WITH FITTINGS SUCH AS BENDS, TEES, REDUCERS, CLAMPS, ETC. INCLUDING NECESSARY EXCAVATION, TRENCH FILLING ETC. COMPLETE. INCLUDING REMOVING EXISTING PIPE LINE IF NECESSARY AND CONVEYING AND STACKING THE SAME AS DIRECTED ETC. COMPLETE.REMOVED SCRAP PIPE SHALL BE TAKEN OUT BY CONTRACTOR

PROVIDING & FIXING CONCEALED / CLAMPED ON WALL ASTRAL/FINOLEX OR EQUIVALENT MAKE UPVC PIPE IN TOILETS WITH NECESSARY FITTINGS LIKE ELBOW, UNIONS, PLUG, PVC INSULATION PIPE & OTHER HARDWARE AND MAKING ALL PIPES LEAK PROOF INCLUDING PLUMBING LINES FOR BELOW MENTION SANITARY FITTINGS FOR 15 MM DIA.

PROVIDING & FIXING CONCEALED / CLAMPED ON WALL ASTRAL/FINOLEX OR EQUIVALENT MAKE UPVC PIPE IN TOILETS WITH NECESSARY FITTINGS LIKE ELBOW, UNIONS, PLUG, PVC INSULATION PIPE & OTHER HARDWARE AND MAKING ALL PIPES LEAK PROOF INCLUDING PLUMBING LINES FOR BELOW MENTION SANITARY FITTINGS FOR 20 MM DIA.

PROVIDING & FIXING CONCEALED / CLAMPED ON WALL ASTRAL/FINOLEX OR EQUIVALENT MAKE UPVC PIPE IN TOILETS WITH NECESSARY FITTINGS LIKE ELBOW, UNIONS, PLUG, PVC INSULATION PIPE & OTHER HARDWARE AND MAKING ALL PIPES LEAK PROOF INCLUDING PLUMBING LINES FOR BELOW MENTION SANITARY FITTINGS FOR 25 MM DIA.

PROVIDING AND FIXING 100 MM RIGID PVC NAHANI TRAP INCLUDING PVC GRATING, BEND, CONNECTING PIECE OF UPVC PIPE UP TO OUTSIDE FACE OF WALL AND OTHER NECESSARY FITTINGS ETC. COMPLETE AS DIRECTED BY EIC.

PROVIDING AND FIXING BRASS PILLAR, STOP TAP OR REGULAR TAP WITH NECESSARY FITTINGS OF SEIKO/PLUMBER OR OF EQUIVALENT MAKE AS APPROVED BY EIC.

SUPPLYING AND FIXING IN POSITION ANODIZED ALUMINUM SECTION TWO TRACK SLIDING WINDOWS AND ONE TRACK FOR MOSQUITO PROOF JALI (WITHOUT BOX FRAME MADE) UP OF THREE TRACK DRAIN BOTTOM SECTION OF SIZE 92 X 31.75 X 1.3 MM THICK (WT. 0.637 KG/M) AND TOP AND SIDES SECTIONS OF SIZE 92 X 31.75 X 1.3 MM THICK (WT. 1.07 KG/M). THE SHUTTER SHOULD BE OF BEARING BOTTOM OF SIZE 40 X 18 X 1.25 MM THICK (WT. 0.417 KG/M), TOP MEMBER OF SIZE 40 X 18 X 1.25 MM (WT. 0.417 KG/M) THICK, INTER LOCKING SECTION SIZE OF 40 X 18 X 1.25 MM THICK (WT. 0.469 KG/M) AND HANDLE SECTION SIZE OF 52 X 18 X 1.13 MM THICK (WT. 0.488 KG/M) SELECTED QUALITY 5 MM THICK CLEAR GLASS TO BE FIXED IN SHUTTER WITH NEOPRENE GASKET WITH APPROVED QUALITY PVC ROLLERS NECESSARY LOCKS HANDLES PVC LINING AND WOODEN ENCASEMENT WHEREVER NECESSARY ETC. COMPLETE AS DIRECTED BY EIC.

PROVIDING AND FIXING IN POSITION ALUMINIUM SLIDING WINDOW OF THREE TRACKS WITH RECTANGULAR PIPE AT WEIGHT 0.637 KILOGRAM/ONE RUNNING METRE.AS PER DETAILED DRAWINGS AND AS DIRECTED BY ENGINEERINCHARGE WITH ALL NECESSARY ALUMINIUM SECTIONS FIXTURES AND FASTENINGS SUCH AS ROLLER BEARING IN NYLON CASTING AND SELF LOCKING CATCH FITTED IN VERTICAL SECTION OF SHUTTER INCLUDING 5 MM THICK PLAIN GLASS AND ALUMINIUM MOSQUITO NET SHUTTER WITH STAINLESS STEEL JALI WITH ALL REQUIRED SCREWS AND NUTS ETC, COMPLETE. WITH POWDER COATING WITH BOX

PROVIDING & FIXING IN POSITION ANODIZED ALUMINUM LOUVERED WINDOWS/VENTILATORS HAVING FRAME MADE OUT OF SIZE 80 X 38 MM X 1.22 MM THICKNESS BOX TYPE WITH SHEET GLASS LOUVERS 5 MM THICK AND WOODEN ENCASEMENT WHEREVER NECESSARY ETC. AS DIRECTED BY EIC.

PROVIDING AND APPLYING OIL BOUND DISTEMPER OF ASIAN PAINTS / NEROLAC / BERGER OR APPROVED BRAND AND MANUFACTURE TO GIVE AN EVEN SHADE WITH APPROVED QUALITY WASHABLE DISTEMPER (READYMADE) OF APPROVED MANUFACTURE'S SPECIFICATION. TWO OR MORE COATS ON NEW WORK. THE JOB INCLUDES PREPARATION OF SURFACE, PROVIDING AND APPLYING MANUFACTURE'S APPROVED DISTEMPER PRIMER AND APPLYING TWO COATS OF BIRLA PUTTY TO MAKE GOOD THE UNEVENNESS OF THE SURFACES INCLUDING NECESSARY SCAFFOLDING ETC. COMPLETE FOR ALL HEIGHTS. AS PER AND AS DIRECTED & INSTRUCTED BY ENGINEER-IN-CHARGE.

PROVIDING AND APPLYING PLASTIC EMULSION PAINT OF ASIAN PAINTS / NEROLAC / BERGER OR APPROVED BRAND AND MANUFACTURE TO GIVE AN EVEN SHADE WITH APPROVED QUALITY ACRYLIC WASHABLE DISTEMPER (READYMADE) OF APPROVED MANUFACTURE'S SPECIFICATION. TWO OR MORE COATS ON NEW WORK. THE JOB INCLUDES PREPARATION OF SURFACE, PROVIDING AND APPLYING MANUFACTURE'S APPROVED DISTEMPER PRIMER AND APPLYING TWO COATS OF BIRLA PUTTY TO MAKE GOOD THE UNEVENNESS OF THE SURFACES INCLUDING NECESSARY SCAFFOLDING ETC. COMPLETE FOR ALL HEIGHTS. AS PER AND AS DIRECTED & INSTRUCTED BY ENGINEER-IN-CHARGE.

PROVIDING AND APPLYING LIQUID ELASTOMERIC POLYMERIZED BITUMINOUS MEMBRANE WATERPROOFING TREATMENT WITH BRUSH APPLIED SINGLE COMPONENT, WATER BASED, COLD APPLIED (TARFELT LM OR EQUIVALENT) INCLUDING CLEANING THE SURFACE AND MADE FREE OF DIRT, DUST, LAITANCE ETC. THE RATE IS INCLUSIVE OF ONE COAT OF PRIMER @0.2 KG/SQM AND TWO COAT OF LIQUID MEMBRANE COATING @ 1.0 KG/SQM FOR TWO COAT ETC. COMPLETE AS PER MANUFACTURE'S SPECIFICATION.

PROVIDING AND APPLYING 100% ACRYLIC EXTERIOR EMULSION PAINT OF APPROVED MAKE AND SHADE ( APEX OF ASIAN PAINT / WEATHER COAT OF BERGER PAINT / EXCEL OF NEROLAC PAINT OR EQUIVALENT) IN TWO OR MORE COATS OVER ONE COAT OF COMPATIBLE PRIMER INCLUDING SCRAPPING, CLEANING, WASHING AND M.S. PIPE SCAFFOLDING ETC. COMPLETE AS DIRECTED BY EIC.

PROVIDING AND LAYING PLAIN FINISH AAP (ATACTIC POLYPROPYLENE POLYMER) POLYMER MODIFIED BITUMINOUS MEMBRANE 3 MM. THICK (WT: 3.5 TO 4.0 KG/SQM) BLACK FINISHED REINFORCED WITH NON WOVEN POLYSTER MATT BY SAME MEMBRANE MANUFACTURER OF FOR WATER-PROOFING OF TERRACE SLAB AND RCC SURFACES AFTER APPLICATION OF COMPATIBLE MODIFIED BITUMINOUS PRIMER @ MIN. 0.25 LTR/SQM AS PER MANUFACTURER'S SOECIFICATIONS, TO SLAB WITH ALL LEADS AND LIFTS WITH TRASVERSE LAPPING OF MIN 75 MM. & LONGITUDINAL LAPPING OF MIN 150 MM. ETC. COMPLETE, LAYER OF PMB MEMBRANE SHALL BE LAID BY USING BUTANE TORCH AND SEALING ALL JOINT ETC. AND PREPARING THE SURFACE AS PER MANUFACTURER'S SPECIFICATIONS AS DIRECTED BY EIC WITH THE FOLLOWING SPECIFICATIONS OF THE MEMBRANE : 1. LONGITUDINAL & TRANSVERSE TENSILE STRENGTH OF MIN 600N & 400N/SCM. LENGTH AT 23 C. 2. LONGITUDINAL & TRANSVERSE TEAR STRENGTH OF MIN 300N & 2500N/SCM. LENGTH AT 23 C. 3. SOFTENING POINT OF NOT LESS THAN 150 C. 4. NON FLOW HEAT RESISTANCE OF NOT LESS THAN 1000 C. 5. COLD FLEXIBILITY OF UP -20 C WHEN TESTED IN ACCORDANCE WITH ASTM, D-5147 PRIMER SHALL HAVE DENSITY.

PROVIDING AND FABRICATING STRUCTURAL STEEL WORK IN ROLLED SECTIONS LIKE JOISTS, CHANNELS, ANGLES, TEES ETC. AS PER DETAILED DESIGN AND DRAWINGS OR AS DIRECTED INCLUDING CUTTING, FABRICATING, HOISTING, ERECTING, FIXING IN POSITION MAKING RIVETED / BOLTED /WELDED CONNECTIONS WITHOUT CONNECTING PLATES, BRACES ETC. AND INCLUDING ONE COAT OF ANTICORROSIVE PAINT AND OVER EPOXY PAINTING OF APPROVED QUALITY ETC. COMPLETE.

PROVIDING STRUCTURAL STEEL WORK IN HOLLOW SECTION OF VARIOUS THICKNESS AND SIZES IN SQUARE, RECTANULAR AND ROUND SHAPE FROM 25MM TO 450MM SECTION AS PER IS 4923 YST 310 GRADE PRODUCED FROM IRON ORE AND BLAST FURNACE ROUTE ETC. AS PER DETAILED DESIGNS AND DRAWING OR AS DIRECTED INCLUDING CUTTING, FABRICATING, HOISTING, ERECTING, FIXING IN POSITION, MAKING RIVETED/BOLTED/ WELDED CONNECTIONS AND EPOXY PAINTING COMPLETE.

PROVIDING AND FIXING 6.00MM THIUCK ISI MARK NON ASBESTOS CEMENT FULLY CORRUGATED ROOF SHEETS CONFORMING TO IS:14871 (LATEST VERSION) OF VARYING LENGTHS WITH TOP SURFACE COATED WITH PURE WATER BASED EXTERIOR GRADE ACRYLIC EMULSION PAINT WITH BOTTOM NATURAL GREYU FINISH INCLUDING 8MM DIA. STAINLESS STEEL (SS 304) J OR L HOOK BOLTS WITH 50MM MINIMUM THREADED LENGTH, SS WASHERS, SS NUTS, CORNER PIECES, RIDGES, GUTTERS, CORNERS, NORTH LIGHT CURVES, CUTTING SHEETS TO SIZE AND SHAPE WHEREVER REQUIRED, NECESSARY M. S. PIPE SCAFFOLDING ETC. COMPLETE AS DIRECTED BI EIC (ENGINEER IN CHARGE). (LAPS SHALL NOT BE PAID EXTRA, SHEET COLOUR TO BE APPROVED BEFORE USE. STANDARD COLOUR OPTIONS TERRACOTA RED/BLUE/GREEN/IVORY WHITE)

SUPPLY OF JCB/HYDRA/TRUCK WITH TOOLS, TACKELS WITH MANPOWER FOR LOADING, UNLOADING FOR ACTIVITIES NOT COVERED IN ITEMS/ FOR SITE CLEARANCE FOR 8 HRS (MIN TWO HRS PAYABLE REST PRO RATA)

PROVIDING AND FIXING MISC. MATERIALS NOT COVERED IN THE SCHEDULE OF RATES INCLUDING TRANSPORTING, LOADING, UNLOADING AT SITE ETC. (CASH RECEIPT TO BE SUBMITTED).

DESIGN OF NEW OFFICE CABIN AT NEW CHEMICAL STORE BUILDING IN CONUSLTATION WITH RCF AS PER MODIFICATIONS SUGGESTED, EXISTING SITE/SOIL CONDITIONS ALONG WITH PREPARATION OF EXISTING AND PROPOSED MODIFICATION DRAWINGS, ELECTRIC LAYOUT DRAWINGS, SUBMISSION OF DETAILED DESIGN AND RCC/FABRICATION DRAWINGS AND ISSUE OF STABILITY CERTFICATE AFTER COMPLETION.