Rashtriya Chemicals And Fertilizers Limited Tender

SUPPLY OF WELDER / FITTER / CUTTER INCLUDING CONSUMABLE AND MACHINERY, TOOLS AS DIRECTED BY EIC. (FOR 8HRS SHIFT)

SUPPLY OF RIGGER / HELPER WITH TOOLS AS DIRECTED BY EIC. (FOR 8HRS SHIFT)

OVERHAULING THE EXISTING ROLLING SHUTTERS PUSH AND PULL TYPE OR GEAR TYPE OF UPTO 15 SQMT. AREA / COLLAPSIBLE GATES INCLUDING REQUIRED OIL & GREASE.

OVERHAULING THE EXISTING ROLLING SHUTTERS PUSH AND PULL TYPE OR GEAR TYPE OF ABOVE 15 SQMT. AREA / COLLAPSIBLE GATES INCLUDING REQUIRED OIL & GREASE.

DISMANTLING THE EXISTING STRUCTURAL STEEL INCLUDING CUTTING & TRANSPORTATION UP TO SCRAP YARD OR CIVIL OFFICE AS DIRECTED.

PROVIDING & FIXING BARBED WIRE [12 GAUGE, 2 PLY] IN LINE AND LEVEL FOR FENCING WORK AS PER INSTRUCTIONS OF ENGINEER IN-CHARGE.

PROVIDING & FIXING CHAIN-LINK FENCING G.I. 50 X 50 X 3 MM AS PER INSTRUCTIONS OF ENGINEER IN-CHARGE.

ERECTING & DISMANTLING SCAFFOLDING WITH CONTRACTOR'S MS PIPES & FITTING AS REQUIRED FOR APPROACH TO SYSTEM BY DOUBLE SCAFFOLDING, ETC. COMPLETE. SUPPORT UP-TO 6 MTR HT

SAME AS ITEM NO-12 WITH SUPPORT 6 M TO 10 M. HT.

SAME AS ITEM NO-12 WITH SUPPORT 10 M TO 20 M.HT.

SAME AS ITEM NO-12 WITH SUPPORT 20 M ABOVE

PROVIDING/FIXING HAND-RAILING WITH G.I. PIPE [M.G] OF HT.1.05 MT WITH 40 MM DIA PIPES FOR VERTICAL POST @ 1.5 MT C/C SPACING. HORIZONTAL PIPE 40 MM DIA AT TOP & 25 MM DIA AT MIDDLE LEVEL. TOE PLATE 100 MM X 6 MM THICK AT BOTTOM LEVEL INCLUDING ONE COAT OF RED OXIDE PRIMER AND TWO COATS OF SYN. ENAMEL PAINT.

FIXING OF AVAILABLE CHEQUERED PLATES/ GRATINGS INCLUDING CUTTING, FABRICATING, PAINTING AND FIXING OF IN POSITION, ETC. COMPLETE AS DIRECTED BY EIC.

PROVIDING AND FIXING IN POSITION AT ALL HEIGHTS MS SHEET STEEL DOORS SHUTTER WITH FRAME OF ANGLE 35X35X4 MM AND 2 MM THK. SHEETS/ 5 MM THICK GLASS. FULL OUTER FRAME SHALL BE 40X40 X5 MM AND FIXED BY HOLD FAST GROUTED/WELDED. DOORS SHALL HAVE PROPER LEVEL ON LOCK STILES AND RAILS TO OPERATE WITHOUT BINDING AND SHALL BE HINGES LOCKING ARRANGEMENT, SURFACE HARDWARE WHERE NECESSARY. AS PER APPROVED DRAWING OF EIC.

PROVIDING AND FIXING IN POSITION CROCODILE SHUTTER GATE AT ALL HEIGHTS MADE OF FLAT & CHANNELS 20 x 5 WITH OUTER FRAME OF ANGLE 40X40X5 MM AND 0.644MM THK. (22 GAUGE) SHEETS, 12 MM SQAURE BAR AT TOP AND BOTTOM AND FIXED BY HOLD FAST GROUTED/WELDED/REVIT 2KG/SQM, BEARING (SKF) 65MM-02 NOS/SQM. AS PER APPROVED DRAWING OF EIC.

PROVIDING & FIXING OF 0.5 MM THICK META COLOUR CORRUGATED GALVALUME SHEETS I.E. 0.45MM BASE METAL THICKNESS AND 0.50MM TOTAL COAT THICKNESS OF MINIMUM YIELD STRENGTH OF 550 MPA AND AS PER THE BELOW MENTIONED TECHNICAL SPECIFICATIONS INCLUDING CORNER PIECE, RIDGE, GUTTERS ETC. FIXING BY SELF TAPPING SCREWS/L-J SS HOOKS. PPGL- PRE PAINTED GALVALUME STEEL SHEET ZINC COATING : AZ 120 PAINT COATING : REGULAR MODIFIED POLYASTER PAINTING PAINTING THICKNESS (TOP) : 25 MICRON PAINTING THICKNESS (BOTTOM) : 5-7 MICRON

PROVIDING MISCELLANEOUS MATERIAL NOT COVERED IN ABOVE ITEMS [CASH RECEIPT TO BE SUBMITTED]

SUPPLYING & FIXING OF 6 MM THICK TOP SIDE COLOUR COATED (RAL 9002 OR AS DIRECTED BY EIC) NON-ASBESTOS CEMENT CORRUGATED SHEETS REINFORCED BY ORGANIC FIBERS AND/OR INORGANIC SYNTHETIC FIBERS CONFORMING TO IS:14871 OF VARYING LENGTHS INCLUDING 8MM DIA. STAINLESS STEEL (SS 304) J OR L HOOK BOLTS WITH 50MM MINIMUM THREADED LENGTH, SS WASHERS, SS NUTS, CORNER PIECES, RIDGES, GUTTERS, CUTTING SHEETS TO SIZE AND SHAPE WHEREVER REQUIRED, NECESSARY M.S. PIPE SCAFFOLDING ETC. COMPLETE AS DIRECTED BY EIC. (LAPS SHALL NOT BE PAID EXTRA, SHEET COLOUR TO BE APPROVED BEFORE USE)

PROVIDING AND FABRICATING STRUCTURAL STEEL WORK IN ROLLED SECTIONS CONFIRMING TO IS 800 : 2007, FIXED WITH CONNECTING PLATES OR ANGLE CLEATS IN MAIN AND CROSS BEAMS, HIP AND JACK RAFTERS, PURLINS CONNECTINF TO TRUSS MEMBERS, JOISTS, CHANNELS, ANGLES, TEES ETC. AS PER DETAILED DESIGNS AND DRAWING OR AS DIRECTED INCLUDING CUTTING, FABRICATING, HOISTING, ERECTING, FIXING IN POSITION, MAKING RIVETED / BOLTED / WELDED CONNECTIONS AND ONE COAT OF ANTICORROSIVE PAINT AND OVER IT TWO COATS OF OIL PAINTING COMPLETE. (RCF WILL SUPPLY ONLY PAINT FREE OF COST AT RCF STORES.)

FIXING OF NEW/OLD RCF ISSUED SHEETS AFTER REMOVING OLD ASBESTOS / FIBER / METAL SHEETS AS PER EXISTING PATTERN BY NEW SS- L & J- SHAPE HOOKS (S.S. HOOKS SHALL BE PAID SEPARATELY IN ITEM NO. 23 BELOW) WITH CAREFULLY SHIFTING/SLIDING OF OLD SHEETS. STACKING OF OLD USABLE MATERIALS & DISPOSAL OF DEBRIS WITHIN TOWNSHIP PREMISES AS DIRECTED BY EIC.

SUPPLYING L & J- SHAPE SS HOOK FOR IS SECTION; MOC= SS 304; DIA.= 8 MM; MINIMUM THREADED LENGTH 50MM INCLUDING EPDM ROUND WASHER / SS ROUND WASHER / SS NUT & PVC CAP ETC. AS DIRECTED BY EIC.

PROVIDING AND FIXING 8MM DIA.,STAINLESS STEEL (SS 304 GRADE), SELF TAPPING/DRILLING SCREWS WITH RUBBER & BITUMINOUS WASHER, FOR CLAMPING SHEETS TO PURLINS AS DIRECTED. RATE INCLUDES SCAFFOLDING / H-FRAME OR ANY TEMPORARY ARRANGEMENT REQUIRED FOR HOOK FIXING UPTO A HEIGHT OF 3M.

SUPPLYING FABRICATING & ERECTING IN POSITION BOLTED AND/ OR WELDED HOT DIPPED GALVANIZED GRATING IN WALKWAYS, PLATFORMS ETC. (FABRICATED AS PER STANDARD DRAWING)MADE OUT OF CONTRACTORS OWN MS PLATES, CHEQUERED PLATE, MS FLATS, HSD REINFORCEMENT BARS INCLUDING CUTTING OF REQUIRED SIZE, SHAPE, MAKING HOLE OF REQUIRED SIZE, MAKING THE EDGES SMOOTH, GETTING IT HOT DIP GALVANISED AFTER FABRICATION, ERECTING USING GI CLAMPS, NUT BOLTS AND WASHERS ETC. ALL COMPLETE. NOTE: 1) ALL MATERIAL TO BE SUPPLIED BY THE CONTRACTOR. 2) HSD REINFORCEMENT SHALL CONFIRM TO IS:1786 FE415 AND MS PLATES/ CHEQUERED PLATE/ MS FLAT SHALL CONFIRM TO IS:2062. 3) HOT DIP GALVANISING SHALL BE OF 80 TO 90 MICRONS THICKNESS 4) PAYMENT FOR G.I. GRATINGS SHALL BE MADE AS PER THE ACTUAL PHYSICAL WEIGHT OF THE G.I. GRATING AS OBTAINED AT SITE. WEIGHMENT AT RCF WEIGH-BRIDGE SHALL BE NECESSARY. 5) THIS INCLUDES SUPPLYING, FABRICATING & ERECTING IN POSITION BOLTED AND/ OR WELDED HOT.( APPROXIMATE WEIGHT OF GRATING SHALL BE 35 TO 40 KG/SQ.)