Pune University Tender

Removing urinal pans or wash hand basins with frame including disconnecting the sanitary and water supply connections, removing the same carefully and stacking the serviceable materials as and where directed including throwing the unserviceable materials outside etc complete

Removing W.C. pans including disconnecting the sanitary and water supply connections, removing and breaking flooring and bed con-crete around pan removing the same carefully and stacking the serviceable materials as adn where directed including throwing the unserviceable materiasls out side etc. carefully and throwing out the refusal outside etc. complete.

Providing and fabricating structural steel work in rolled sections like joists, channels, angles, tees etc. as per detailed design and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted / bolted /welded connections without connecting plates, braces etc. and including one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade etc. complete

Providing, fabricating and erecting at site of work the tubular steel structure (shed) as per standard design and specifications having various spans in between trusses and in multiples of standard length of bays as specified as per standard specifications, inclusive of cost of steel tubular trusses, tubular columns purlins, tie runners, foundation bolts, base plates, nuts and bolts, welding wherever required etc. as per detailed drawing inclusive of one coat of anticorrosive paint and two coats of oil painting of approved quality and shade etc. complete. Spec. Number : As directed by Engineer-in-charge.

Providing internal cement plaster 12mm thick in single coat in cement mortar 1:4 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. complete.

Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1Kilogramper cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete

Providing and laying ceramic tiles of having size 30 cm. x 30 cm. and confirming to corresponding I.S. for dado and skirting in required position with readymade adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white/ colour cement slurry cleaning curing etc. complete.

Providing and laying in position flooring of telephone black / Amba White / Cat bary brown / Ruby red / Ocean Brown granite stone of approved shade and size 18 mm to 20 mm thick on bed 1:6 cement mortar including cement floats striking joints, pointing in C.M. 1:3 curing and cleaning etc. complete.

Providing and fixing 2 mm thick polyvenyl venyl chloride flooring including leveling the base with white cement including pasting with appropriate material cleaning the surface etc.complete

Providing and applying priming coat on concrete/ masonary/ Asbestos Cement plastered surfaces including scaffolding if necessary, preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and sand papering as required etc. complete.

Providing and applying pearl/ luster finish paint of approved colour and shade to the existing plaster surface including scaffolding, preparing the surface, applying the acrylic wall putti etc.complete

Providing and applying two coats of exterior weather shield paint of approved manufacture and of approved colour to the plastered surfaces including cleaning ,preparing the plaster surface ,applying primer coat ,scaffolding if necessary, and watering the surface for two days etc complete

Providing and applying washable oil-bound distemper of approved colour and shade to old and new surfaces in two coats including scaffolding, preparing the surfaces. (excluding the primer coat.) etc. complete.

Providing and applying Two coats of wall care Putty on plastered surface and Ceiling and Walls to prepare surface even and smooth of approved make, etc complete

Providing and fixing false ceiling of 15mm thick as per drawings including powder coated G.I. wall angle of 20 mm x 20 mm x 0.60 mm size, G.I. grid runners of size 15 mm x 38 mm at 600 mm center to center both ways and suspended using G.I. 3 mm wire including fixing using butterfly clips and fasteners including transporting, scaffolding all necessary labour and machinery, finishing etc. complete

Providing and fixing in position Gypsum board false ceiling with 12.5 mm thick Gypsum boards, Providing and fixing in position Gypsum board false ceiling with 12.5 mm thick Gypsum boards, screwed/fixed to the under structure of suspended G.I. Grid constructed and suspended from the main ceiling consisting of ceiling sections of size 25 x 50 mm maximum center to center distance of 600 milimetre perimeter channel and intermediate channels at maximum center to center distance 1200 milimetre galvanized grid should be fixed to reinforced cement concrete slab. The gypsum board should be fixed to galvanized iron grid with necessary screws. The boards should be taped and filled from underside to give smooth, seamless ceiling. The rate should include necessary additional ceiling sections and intermediate channels. Additional intermediate channels should be fixed to strap hangers for additional support to prevent strapping at every 1200 milimetre item to be completed in all respect including necessary sleeves for ducts finishing of joints cut outs, painting including labour, material, lifts etc. all complete.

Providing and fixing in position, Single shuttered aluminium extruded powder coated openable door of overall size 0.90 m x 2.40 m with aluminium door frame of powder coated section 101.60 x 44.75mm , 3.18 mm thick and shutter comprising of powder coated section having bottom and lock rail of size 150 mm x 44.5 mm x 3.00 mm thick top rails 47.62 x44.45 mm x 3.00 mm thick , vertical style 47.62 x 44.45 mm, 3.00 mm thick and for shutter plain glass panes 5 mm thick for top panels and 12mm thick both side laminated phenol bonded particle board panels for bottom panels etc. , I.S.I. mark , heavy duty, Hydraulic floor spring of 150Kilogramcapacity , having heavy duty concealed lock, necessary beading, glazing clips, PVC gaskets, 250mm length tower bolts, 150mm diam. pad handle, etc. as per detailed design and drawing or as directed by engineer in charge including all materials , labours, and equipment etc.Complete

Providing and fixing in position powder coated aluminium louvered windows / ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 x 38 mm x 1.22 mm box type, 5 mm thick sheet glass louvers, of approved quality etc. complete

Providng and fixing in position anodised extruded aluminum partitions, partly glazed and partly laminated having frame made out of extruded tubular section of size 40 mm x 60 mm with 12 mm thick three layered flat pressed teak wood particle board bonded with BWP type exterior grade phenol formaldehyde synthetic resin conforming to IS 128231990, laminated on both sides,Novateakor equivalent and 5 mm thick selected quality plain/ float glass panels fixed with aluminum glass clips 12 mm x 12 mm and rubber cushioning beading to glass partitions as per approved drawing etc. compete

Providing and fixing on walls/ ceiling/ floors, 15 mm dia. heavy grade having embossed as ISI Mark galvanised iron pipes weight of 1.48 Kilogram/metre with necessary fittings. remaking good the demolished portion and applying primer of anti-corrosive oil paint 2 coats Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in Estate Office or as directed etc. complete.

Providing and fixing on walls/ ceiling/ floors, 25 mm dia. heavy grade having embossed as ISI Mark galvanised iron pipes weight of 1.48 Kilogram/metre with necessary fittings.remaking good the demolished portion and applying primer of anti-corrosive oil paint 2 coats Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in Estate Office or as directed etc. complete.

Providing and fixing on walls/ ceiling/ floors, 32 mm dia. heavy grade having embossed as ISI Mark galvanised iron pipes weight of 1.48 Kilogram/metre with necessary fittings.remaking good the demolished portion and applying primer of anti-corrosive oil paint 2 coats Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in Estate Office or as directed etc. complete.

Providing and fixing on walls/ ceiling/ floors,40 mm dia. heavy grade having embossed as ISI Mark galvanised iron pipes weight of 1.48 Kilogram/metre with necessary fittings. remaking good the demolished portion and applying primer of anti-corrosive oil paint 2 coats Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in Estate Office or as directed etc. complete.

Providing and fixing 15 mm dia. screw down bib/ stop tap of brass including necessary socket union nut complete.

Providing and fixing 25 mm dia. screw down bib/ stop tap of brass including necessary socket union nut complete.

Providing and fixing 15cm x 10cm salt glazed stoneware gully trap in cement concrete 1:4:8 outside the building including cast iron grating in the sink, connecting glazed stoneware pipe,brick masonry chamber with cast iron lid and cast iron grating for the gully trap

Providing and fixing laying P.V.C. Pipe of 40 mm dia with fittings such as bends, tees, reducer, clamps, etc. including necessary excavation, trench filling etc. complete. Spec. No: - As directed by Engineer in charge.

Providing and fixing laying P.V.C. Pipe of 50 mm dia with fittings such as bends, tees, reducer, clamps, etc. including necessary excavation, trench filling etc. complete. Spec. No: - As directed by Engineer in charge.

Providing and preparing kitchen otta made up from 30 mm thick and 75 cm. wide one side polished kadppa top 75 cm. wide one side polished kadappa top 75 cm high vertical support for kadppa at 1 m. c/c of 25 mm thick both side polished kadappa middle shelf and bottom of 20 mm thick one side polished kadappa with facia patti of 20 x 50 mm kadappa including all material labour cutting fixing with cement mortar and araldite curing polished and cleaning etc. complete.

Providing and fixing 10 cm PVC nahani trap with grating etc. complete

Providing and fixing PVC MULTI nahani trap with grating etc. complete. Spec. No: - As directed by Engineer in charge

Providing and fixing stainless steel sink of size 600 x 510 x 200 mm incluidng coupling, outlet pipe, elbow and other necessary fitting, finishing etc. complete.

Providing and fixing C.P. Angular stop clock with wall flange of approved make continental including necessary sockets/union nut etc. complete.

Providing and fixing C.P. pillar cock long neck with aerator of approed make including necessary sockets/union nut etc. complete.

Providing and fixing C.P. sink cock with raised J" shaped swinging casted spout ofapproved make including necessary sockets/ union nut etc. complete.

Concealed the pipe line (Approved rate)

Providing and making Holes (Core cutting ) in chajjas and slab for passing the pipe line. Spec. No: - As directed by Engineer in charge

Providing and fixing Godrej make door clooser with all fixtures and fittings Spec. No: - As directed by Engineer in charge

Providing and fixing Rolling Blinds of approved make & shade with Blackout fabric& telting with chain(Ball)system with all necessary fixtures and fitting etc.complete.(Sample to be final by Engineer In-charge prior execution of work) Spec. No: - As directed by Engineer in charge . Brands- D Décor, MAC,Johnson

Mazdoor, Unskilled Heavy Male/Female Spec. No: - As directed by Engineer in charge

Providing Plumber with tools - Skilled Spec. No: - As directed by Engineer in charge

Providing and fixing Three way tab for laboratory etc complete. Spec. No.: As directed by Engineer in charge.,

Providing and fixing C.P. wall mixer with provision for overhead shower with 115mm long bend pipe and wall flange of approved make including necessary sockets/union nut etc. complete

Providing and fixing 100 mm dia.chromium plated brass showers rose to15mm dia.supply pipe including necessary bend and socket complete.

Providing & Fixing Calcium Silicate boards (Hilux boards) of 12mm thk for Ceiling/Wall by self drilling & tapping screws including Filling the gap between boards with joint compound & fibre tape together for seamless finish etc complete

Providing and fixing stage with 18mm ply with approved make. internal members using 18 mm ply at every 600mm c/c bothways .300mm depth finished with l mm thk laminate of approved make on outer side excluding the top face of stage. etc complete. Top area of stage will be considered for measurement.

Providing and fixing flush door shutter in Double leaf 34 mm thick with teak wood bidding of size 32x12mm thk finished with 1 mm thick laminate of approved colour on both faces also including vision panel glass 5mm thick fixing with teak wood bidding on both side of vision as per given detail drawing and all necessary hardware & accessories like Hinges, D type handles on both sides, Tower bolt, Aldrops, Door stopper, as directed by Engineer Incharge etc.complete.

Providing and fixing flush door shutter in Single leaf 34 mm thick with teak wood bidding of size 32x12mm thk finished with 1 mm thick laminate of approved colour on both faces also including vision panel glass 5mm thick fixing with teak wood bidding on both side of vision as per given detail drawing and all necessary hardware & accessories like Hinges, D type handles on both sides, Tower bolt, Aldrops, Door stopper, as directed by Engineer Incharge etc.complete.

Providing and Fixing Anchar Fastner 100mm length in Wall of 10mm dia. including drilling etc complete. Spec. No.: As directed by Engineer in charge.,

Providing and fixing shirkes modular kitchen for nutrition lab with tandem drawers - 25 nos, bin holder-2 NOS, cutlery tray in PVC,cup sauscer rack and thali rack in ss make all are 1 nos , with hi gloss laminate finish shutters with skirting. Base unit modular carcass with hinges of hettich make as per design and drawing etc complete & as directed by Engineer in charge

Modular Furniture for Computer Lab /Conference Table / FacultyTable Low Height Partition:- Providing and fixing Low Height partition 75 mm th. consisting of tile 10 mm th. particle board based modular panels system of specified shade and colour and with eatched glass of 6 millimeter thick and soft board and cloth as a pinup board on metal section, fabricated M.S. components and alluminium profiles along with all trims as finished in epoxy powder coating of a thickness 45 to 50 mocrons with box type skirting raceway for wiring and with all slots in vertical and horizontal members of height 100 millimeter meant to carry wire; the frame of partition should be free standing and self supporting with leveling system to adjust the panels to unevness and differences in floor levels as per detailed drawing NO, 1 and as directed by Architect/Engineer in charge.

Providing and fixing fibre/EBCO key board with telescoping channel size 50cm x30cm.including necessary fitting ,as per standard specificationgn and drawing etc. Complete. as directed by Engineer Incharge.

Providing and fixing glass partion with 12 mm modi glass including acid eatching, polished at top and front fitted in D bracket to 25 mm etc. Complete. as per the drawing as directed by Engineer Incharge.

Providing and fixing foot rest with 18mm. Prelam board box type , top side closed and bottom side open as per design and drawing etc. Complete. as directed by Engineer Incharge. (only Top view measurements are consider for payment)

Providing and fixing post forming both side laminated top/vertical support with particle board (25mm side in postform,2mm edge banding, Here in after written as PF- BSL particle board) etc. Complete. as directed by Engineer Incharge. (Note :- Shade and colour of Mirror shine prelaminated particle board should be got approved from Engineer Incharge before fixing in position) 25mm Top/ vertical support.

Providing and fixing storage unit ( storage Runner) of W 0.45 meter made of 18 mm thick plywood of approved make including shelf as per drawing and shutters both made of 18 mm thick plywood, and storage unit is finished with approved quality 1 mm thick laminate outer side& inner side finished with white laminate with all necessary fittings like drawer channels, hinges, towerbolt handels, lock, safety chain, magnetic stoppers of approved make etc. melamine polishing for exposed edges As directed by Engineer Incharge etc complete.

Providing & Fixing storage cabinet stanadard depth 18" out to out made of 18 mm thick plywood of approved make including five shelf as per drawing and shutters both made of 18 mm thick plywood , back covered with 12 mm plywood Storage unit is finished externally with approved quality 1 mm thick laminate including finishing inner side with 0.8 mm thk laminate& back side by two coats of french polish with necessary fixtures & fastening as per detailed design & drawing and as directed by Engineer in charge.etc.complete.

Table :- Providing and fixing Table size of L 1.5 meter X W 0.75 meter x H 0.75 meter here in after written as (L - for length & W - for width & H for height) Top of table made out of 25 mm thk. plywood with laminate both side full round post form and remaining two sides finished with 2 mm thk. PVC edge band and vertical support made out of 18 mm thk.plywood with laminate both side full round post form and remaining two sides finished with 2 mm thk. PVC edge band. Modesty made out of 18 mm thk.plywood with laminate both sides finished with 2 mm thk. PVC edge band with foot rest of size 0.8 m. x 0.3 m , ready made key board, wire manager using the hardware and handles, locks and magnetic stoppers where ever necessary as directed by Engineer in charge. (Note :- Shade and colour of Mirror shine / Matt finish laminated sheet should be got approved from Engineer Incharge before fixing in position)

Table :- Providing and fixing Table size of L 1.2 meter X W 0.6 meter x H 0.75 meter here in after written as (L - for length & W - for width & H for height) Top of table made out of 25 mm thk. plywood with laminate both side full round post form and remaining two sides finished with 2 mm thk. PVC edge band and vertical support made out of 18 mm thk.plywood with laminate both side full round post form and remaining two sides finished with 2 mm thk. PVC edge band. Modesty made out of 18 mm thk.plywood with laminate both sides finished with 2 mm thk. PVC edge band with foot rest of size 0.6 m. x 0.3 m , ready made key board, wire manager using the hardware and handles, locks and magnetic stoppers where ever necessary as directed by Engineer in charge. (Note :- Shade and colour of Mirror shine / Matt finish laminated sheet should be got approved from Engineer Incharge before fixing in position)

Pedestal :- Providing and fixing Pedestal unit of L 0.4 meter X W 0.55 meter x H 0.725 meter size including 1 drawer & 1 shutter ,with 18 mm thk plywood with laminate both sides finished with 2 mm thk. PVC edge band at Top with 18 mm thk plywood with laminate finished with 2 mm thk. PVC edge band for verticals , bottom and 12mm plywood with laminate both side at back with hinges. handles, locks & Drawer channel where ever necessary, shutters finished with 2 mm thk. PVC edge band & necessary hardware as per drawing and the specifications, as directed by Engineer in charge. etc complete.(Note :- Shade and colour of Mirror shine / Matt finish laminated sheet should be got approved from Engineer Incharge before fixing in position)

Side Unit :- Providing and fixing side unit L O.9 meter X W 0.45 meter x H 0.725 meter size including 2 drawer & 2 shutter ,with 25mm thk plywood with laminate both side full round post form on face and remaining 3 sides finished with 2 mm thk. PVC edge band at Top. 18 mm thk plywood with laminate finished with 2 mm thk. PVC edge band for verticals , bottom and 12mm plywood with laminate both side at back with hinges. handles, locks ,Drawer channel where ever necessary, both shutters finished with 2 mm thk. PVC edge band & necessary hardware as per drawing and the specifications, as directed by Engineer in charge. etc complete.Note :- Shade and colour of Mirror shine / Matt finish laminated sheet should be got approved from Engineer Incharge before fixing in position)

Supplying and erecting Benches of size W 1100 mm x D 1000 mm x Desk H 800 mm Bench H 450 mm having sprcification below& as per drawing and as directed by Engineer-inchrge Technical Specification of Benches 1. The overall dimensions of desk will be W1100mm x D1000mm x Desk H 800mm, Bench H 450mm, complete as per drawing enclosed and direction of Engineer-in- charge having the following specifications 2. Side frame structure: Made of prime quality CRCA pressed form section 175mm x 25mm x 1mm thick welded to 25mm x 50mm x 1.2mm thick CRCA tube. Seat and back side frame structure also made of prime quality CRCA pressed form section 175mm x 25mm x 1mm thick welded to 25mm diameter x 1.6mm thick ERW-1pipe. All 8 nos. horizontal supports are 25mm x 25mm x 1.2mm thick shall be of CRCA tube. 4 nos CRCA tube size 20 x 20 x 1mm thick insert for full height in Big pillar. Rectangular tube 50 x 25 x 1.2mm thick should be closed with PPCP cap bothside stand pipe dia. 25mm x 1.6mm thick should be closed with metal (Backside) and other side (Under the seat) PPCP cap, complete as per drawings & As directed by Engineer in Charge. 3. Front panel cum tray shall be made of prime quality 0.8mm thick CRCA sheet of H150mm x W1050mm x D300mm with middle partition and side stiffeners of MS CRCA tube size 20mm x 20mm x 1mm thick. One vertical support (partition) of square tube size 25mm square x 1.2mm thick must be provided at centre of tray and Front Face may be embosed as per drawing 4. Additional front panel prime quality 0.8 mm thick CRCA sheet of size H150mm x W1050mm x D20mm with square perforation. CRCA Tube of size 20 x 20 x 1mm thick to be inserted for full length at bottom of Jali as shown in Drawing & As directed by Engineer in Charge. 5. Desktop, seat and back shall be made of IS:303, 18 mm thick plywood of MR grade having AA types of surfaces of BSL (Under side 0.8mm thick white lamination and Top side 1mm thick Grey Colour) and edges must be sealed with BTC lipping. Sizes are below: 1. Seat W 1100mm X D 300mm. 2. Desktop W 1110mm x D 380mm 3. Back 1100mm x D150 mm 4. One long edge of Desk top, seat & back shall be post formed with round edge. 6. Desktop must be fitted with M6 sunken bolt 3nos. size M6 x 35mm length Zinc plated from Topside, maximum distance 40 mm from desktop edge and 3nos. MS Zinc plated screw self-tapping size dia. 4mm x 38 length again from Bottom side. The fixing of desktop, seat and back shall have vandalism- proof mechanism. (f) Seat and back each must be fitted with 6 nos. MS screw Zinc plated self tapping size dia. 4mm x 38 length from Bottom side (g) Hooks made of MS wire dia. 5mm and size W 23mm, D 32mm and H80mm must be provided on inner side of vertical pressed formed steel section on both sides (h) (i) All Pipes/Tubes shall be of ERW-1, IS- 3074-2005 and CRCA sheet, IS -513 CR-2 Designation- Grade D). (ii) All MS. CRCA parts must be MIG, TIG or spot welded as per technical requirement Permissible deviation in the dimensions is +/- 5%.

Meeting Hall Chair :- Supply of Netted medium back revolving chair with Gas Lift and Crome plated base with nylon Twin Casters, Netted back with adjusted support, back made up of Nylon Frame covered with High quality Nylon Mesh with 32 Density P U Foam. Seat is made up of 15 mm thick Hot press Ply with 50 density moulded foam covered with High quality Nylon mesh with aster crome plated pipe with all way adjustable and heavy duty P. U. Soft Handles with Metal adjustable Handle duly powder coated with PU pad, Tilt Mechanisum with multiangle locking fitted to seat with inserts. (As per drawing & Specification attached on annexture I)

Meeting Hall Chair Person Chair :- Supply of Netted High Back Revolving Chair with Gas Lift and Crome Plated base with Nylon Twin Casters, Netted Back Adjusted support and adjustable Head Rest made up of Nylon Frame with 32 density P U Foam covered with high quality Nylon Mesh, Seat is made up of 15 mm thick hot press with ply with 50 density moulded foam covered with High quality Nylon Mesh, with aster crome plated pipe with all way adjustable and extra Heavy duty Metal adjustable Handle duly powder coated with PU pad, Tilt Mechanisum with multiangle locking fitted to seat with inserts. (As per drawing & Specification attached on annexture I)

Faculty Chair :- Supply of netted high back revolving chair, with gaslift & crome plated base with twin nylon casters, netted back with adjustable lumber support & adjustable head rest, back made up of nylon frame with nylon mesh support, with 32 density P U foam. seat is made up of 15 mm thick hot press ply with 50 density moulded foam covered with high quality nylon mesh with aster, metal adjustable handles with P U pad fitted to seat with inserts, tilting mechanisum with No.multiangle locking system fitted to seat with inserts. (As per drawing & Specification attached on annexture I)

Staff Chair :- Supply of medium back revolving chair, with gas lift, crome platted base with nylon twin casters, Tilting/push back mechanism with front locking system, nylon streep (Horizontal Lines) type frame with high quality nylon mesh at back moulded 50 density foam seat with fabric/leatherite uphostery at seat 15 mm hot press ply at seat with inserts for handle & mechanisum, tringle type pp handle (As per drawing & Specification attached on annexture I

Writing Pad Chair - Flap chair with S type frame 25 mm x 1.6 mm, CRCA pipe frame with book rack & colapsible writing pad. Overall height 960 mm, back width 470 mm, back height from seat 560 mm, seat depth 500 mm, book shelf height from ground 185 mm, depth of book shelf 380 mm, C bend of book shelf from front 90 mm, 12 mm hot press plywood with moulded foam & netted foam tepestery at seat, 19 mm x 1.6 CRCA pipe frame at back with nylon mesh tepestery from both side & two support belts at back.18 mm ISI mark plywood with both side laminate & polished teakwood leaping for writing pad. All way adjustable mechanisum to writing pad, 6 mm rod book rack under seat good quality bushes pvc at bottom. Back is fitted under seat at three places with nut bolt with material to be used for Chair as Shown in Photograph of chair and as directed by Engineer in charge.

Fix Type Chair ( S Type Chair) - 25mm x 1.6mm CRCA Pipe frame duly powder coated with 12 mm. Thick Hot Press ply seat with moulded foam and Netted Tepestery. 19 mm x 1.6 CRCA pipe frame back with both side Nylon Mesh & Two Support Belts at back crome double bar handle with PU cushion. Good quality bushes PVC at bottom. Over all height 960 mm, back width 470mm, back height from seat 560mm Seat Size 500 mm x 470 mm. Frame duly powder coated.

Computer Chair :- Supply of low back revolving chair with gaslift & crome platted base with nylon twin casters, 50 density moulded foam with fabric netted tapestry at seat & 15 mm Hot press ply for seat. High quality nylon mesh with nylon frame at back, pp handles, push back mechanism with fornt locking system. (As per drawing & Specification attached on annexture I)

Laboratory Furniture(Work stations/ Laboratory Tables) General Lab -Manufacturing, assembling, transporting and placing / fixing in position Mirror cabinet of Overall Size:- 3440 mm X1450 mm X 800 mm H Structure Made up of 50X50X1.6 mm thick CRCA pipes,overall structure duly coated with antirust epoxy powder coating of 60 micron,both side alternate storage cabinets below lab platform made up of 22 gauge CRCA sheet, storage including one drawer & shutters having 2 chemical resistant compartment inside as per drawing- including PP (Polypropylene) Lab Sink with Sink cock with all accessories of size 560mm X 355mm X 245mm (depth) mm including coupling ,outlet pipe,elbow and other necessary fitting,finishing. bottle racks having two shelf & 4 no. electric sockets with switch & MCB.Table top made up of 18-20 mm thick granite of approved make with all side edge chamfering, with 4set of gas burner with all plumbing & gas line including all necessary fixtures & fastner etc.and as directed by Engineer Incharge.

Laboratory Furniture(Work stations/ Laboratory Tables) General Lab -Manufacturing, assembling, transporting and placing / fixing in position plain tables without storage overall size:-1400X1400X800H Structure Made up of 50X50X1.6mm thick CRCA pipe frame overall structure duly coated with antirust epoxy powder coating of 60 micron, Table top made up of 18-20 mm thick granite of approved make with all side edge chamfering including all necessary fixtures and fastening etc.and as directed by Engineer Incharge.

Cell culture lab & Bio Safety Lab - Manufacturing, assembling, transporting and placing/fixing in position plain tables with alternate storage of overall size:- 3565X750X800H,Structure Made up of 50X50X1.6 mm thick CRCA pipe frame, overall structure duly coated with antirust epoxy powder coating of 60 micron with alternate storage cabinets below lab platform.storage cabinate made up of 22 gauge CRCA sheet ,storage including one drawer & shutters having 2 chemical resistant compartment ,Table top made up of 18-20 mm thick granite of approved make with all side edge chamfering including all necessary fixtures and fastening etc.and as directed by Engineer Incharge.

Laboratory Furniture(Work stations/ Laboratory Tables) Cell culture lab - Manufacturing, assembling, transporting and placing/fixing in position plain tables with alternate storage of overall size:- 1480X750X800H Structure Made up of 50X50X1.6 mm thick CRCA pipe frame,overall structure duly coated with antirust epoxy powder coating of 60 micron with alternate storage cabinets below lab platform.storage cabinate made up of 22 gauge CRCA sheet ,storage including one drawer & shutters having 2 chemical resistant compartment , Table top made up of 18-20 mm thick granite of approved make with all side edge chamfering including all necessary fixtures and fastening etc.and as directed by Engineer Incharge.

Laboratory Furniture(Work stations/ Laboratory Tables) Molecular Biology Lab - Manufacturing, assembling, transporting and placing/fixing in position plain tables with alternate storage of overall size:- 5400X750X800H Structure Made up of 50X50X1.6 mm thick CRCA pipe frame,overall structure duly coated with antirust epoxy powder coating of 60 micron with alternate storage cabinets below lab platform.storage cabinate made up of 22 gauge CRCA sheet ,storage including one drawer & shutters having 2 chemical resistant compartment ,Table top made up of 18-20 mm thick granite of approved make with all side edge chamfering including all necessary fixtures and fastening etc.and as directed by Engineer Incharge.

Laboratory Furniture(Work stations/ Laboratory Tables) Molecular Biology Lab - Manufacturing, assembling, transporting and placing/fixing in position plain tables with alternate storage of overall size:- 7500X750X900H, Structure Made up of 50X50X1.6 mm thick CRCA pipe frame,overall structure duly coated with antirust epoxy powder coating of 60 micron with alternate storage cabinets below lab platform.storage cabinate made up of 22 gauge CRCA sheet ,storage including one drawer & shutters having 2 chemical resistant compartment , Table top made up of 18-20 mm thick granite of approved make with all side edge chamfering including all necessary fixtures and fastening etc.and as directed by Engineer Incharge.

Laboratory Furniture(Work stations/ Laboratory Tables) Analytical Lab- Manufacturing, assembling, transporting and placing / fixing in position plain tables with alternate storage of overall size:- 6050X750X800H, Structure Made up of 50X50X1.6 mm thick CRCA pipes, overall structure duly coated with antirust epoxy powder coating of 60 micron, alternate storage cabinets below lab platform made up of 22 gauge CRCA sheet, storage including one drawer & shutters having 2 chemical resistant compartment inside as per drawing- including PP (Polypropylene) Lab Sink with Sink cock with all accessories of size 560mm X 355mm X 245mm (depth) mm including coupling ,outlet pipe,elbow and other necessary fitting,finishing.Table top made up of 18-20 mm thick granite of approved make with all side edge chamfering including all necessary fixtures and fastening etc.and as directed by Engineer Incharge.

Laboratory Furniture(Work stations/ Laboratory Tables) Analyical Lab -Manufacturing, assembling, transporting and placing/fixing in position plain tables with alternate storage of overall size:-7500X750X800H, Structure Made up of 50X50X1.6 mm thick CRCA pipe frame,overall structure duly coated with antirust epoxy powder coating of 60 micron with alternate storage cabinets below lab platform.storage cabinate made up of 22 gauge CRCA sheet ,storage including one drawer & shutters having 2 chemical resistant compartment , Table top made up of 18-20 mm thick granite of approved make with all side edge chamfering including all necessary fixtures and fastening etc.and as directed by Engineer Incharge.

Laboratory Furniture(Work stations/ Laboratory Tables) Sample preparation -Manufacturing, assembling, transporting and placing/fixing in position plain tables with alternate storage of overall size:-2300X750X800H, Structure Made up of 50X50X1.6 mm thick CRCA pipe frame,overall structure duly coated with antirust epoxy powder coating of 60 micron with alternate storage cabinets below lab platform.storage cabinate made up of 22 gauge CRCA sheet ,storage including one drawer & shutters having 2 chemical resistant compartment , Table top made up of 18-20 mm thick granite of approved make with all side edge chamfering including all necessary fixtures and fastening etc.and as directed by Engineer Incharge.

Providing, fixing, jointing and testing 75 mm dia Polypropylene Pipes chemical resistance astral make in proper line and level fixed to walls or ceiling or run on floor or in trenches at required slopes etc as directed by Engineer in charge

Providing, fixing, jointing and testing Polypropylene chemical resistance astral make Nahni traps of 100 mm dia.with self cleansing design with water seal with necessary fittings etc.as directed by Engineer in charge