Pune University Tender

Providing flyash brick masonry with conventional/I.S.type flyash bricks in C.M.1:6 in foundation and plinth including bailing out water manually striking joints,racking out joints watering and scaffolding etc. complete.

Providing sandfaced plaster externally in cement mortar using approved screened sand,in all positions including base coat of 15mm thick in cement mortar1:4 using waterproofing compound at 1 Kilogram per cement bag curing the same for not less than 2 day sand keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8mm thick in cement mortar 1:4 finishing the surface by takingout grains and curing for fourteen days scaffolding etc.complete.

Providing and fixing heavy duty inter locking concrete Gray paving blocks of 80 mm thickness of having a strength of 300 kg/Sq.cm. of approved quality and shape on a bed of crushed sand of 25 to 30 mm thick including skirting joints and cleaning etc. complete. Spec. No.:A directed by Engineer in charge

Providing and applying two coats of exterior weather shield paint of approved manufacture and of approved colour to the plastered surfaces including cleaning ,preparing the plaster surface ,applying primer coat ,scaffolding if necessary, and watering the surface for two days etc complete. NOTE: As directed by Engineer- incharge.

Providng Mazdoor - Unskilled Light male Spec. No.As directed by Engineer in charge.

Material shifting by truck Sp.As directed by Engineer in charge.

Providing and fixing 100 mm dia stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. com-plete. Spec. No.: As directed by Engineer in charge. (Make- Finolex, Supreme, Kisan, Prince)

Providibg and Fixing Cross Trainer DIMENSIONS:-1320mm (Length)x 600mm (Width) x 1750mm. (Height). SAFE AREA:-1.77x1.2Mtr. Crosstrainer equipment madefrom“B” Class G.I.Pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Dia. of pipe in millimeters. Make of G I Pipe will be of Tata, Jindal, Swastik, Zenith or Siddharth. The main frame Pipes are of 80NB “B”ClassG.I.Pipe with single bend pipe with 250mm radius. The bottom support of M.S. round plate of Ø250mm &10mm thick. The Handle Frame is made up of 25NB “B” Class G.I. Pipe. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “B” class welded with M.S. round plate of Ø250 mm &10mm thick. Main pipe supported with 25mm X 25mm M.S.angles of 2mm thickness and 20mm x 40mm MS square pipes of 2mm thickness. To build structure bushes are used which are made from M.S. seamless pipe of 60mm OD. With 5 mm thickness. The foot rests are made from HDPE / LLDPE material of size 130mm X 310mm X 5mm thickness and mounted on M.S.Plate of Size 130mm x 310mm x 3mm thick Closing Caps are made up of highquality HDPE / LLDPE Plastic material. Pins used of Diameter 35mm, 25mm, and 17mm are made up from bright material. The Bearings used are of “6007zz” “6205zz” and “6203zz” permanent lubricated sealed bearing of reputed brand like SKF, FAG. High tensile steel with galvanized nuts and bolts are used for assembly. A16 , A 24 mm circlips are usedforassembly. Bolt M8X16 mm and NY lock nut of M8 made of SS are used on nylon cap mounted on pins to protect bearings and pins from rain and dust. The foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x 0.3m below ground level and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint or duly powder coated of minimum 60 micron thickness. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment etc all. Rate inclusive of labour, material, taxes, transport, etc complete all As directed by Engineer-in-Charge

Providing and Fixing Arm & Paddle Bike Providing and fixing Cycle made from “B” class G.I. Pipe. The main frame of Ø40mm made from “C” Class G.I. pipe. For the support of foot pedal M.S. round plate of Ø250 mm & 10mm thickness is used. The handle frame is of Ø32mm made from “C” Class G.I. pipe. The seats is fitted on the frame is made up of high quality FRP material of size 330 mm X 300 mm of thickness 3 mm & M.S. Plate of thickness 5 mm and Size 250 mm X 200 mm is used to Support it. The foundation used for fixing is consists of 25 mm X 25mm M.S. angle of 3 mm thickness. Closing Caps made from top up of Ø 25mm bright bar. The bearings used are “6205zz” permanent lubricated sealed bearing of reputed make (SKF/FAG). High tensile steel with galvanized nut bolts are used for assembly. The serclips used for assembly are of Ø25 mm. The foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x 0.3m below ground level and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint or duly powder coated of minimum 60 micron thickness. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment etc all. Rate inclusive of labour, material, taxes, transport, etc complete all. As directed by Engineer-in-Charge

Providing and Fixing Rower Providing and fixing rower made from “B” Class G.I. Pipe. The Main frame is of 80mm X 40mm & 40mm X 40mm CRC Pipe with 2 mm thickness. The handle frame is of 25 NB made from “C” class G.I. pipe. The Foundation used for Fixing consists of three equal items i.e. 40mm NB made from “C” Class G.I. pipe, C channel of 75mm X 40mm X 5mm & 25mm X 25mm X 3mm M.S. angle. To join the movement frame to main frame seamless pipe of 50mm dia & 3mm thickness is used. The seats which are fitted on the main frame is made up of high quality FRP material of size 330mm X 330mm of thickness 3 mm & M.S. plate of size 250mm X 200mm X 5mm is used to support it. Closing caps are made from top quality FRP material which is of 2 mm thickness. The pins used are made up of 17mm diameter hardened bright bar. The bearings used are of “6203” permanent lubricated sealed bearing of reputed make foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x 0.3m below ground level and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint or duly powder coated of minimum 60 micron thickness. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment etc all. Rate inclusive of labour, material, taxes, transport, etc complete all. Work done should be as per engineer incharge. The handles used are of Rubber grip. The nut bolts used for assembly are made from S.S. material. The bushes (Stopper) used to avoid the collusion made from Poly Urethane Plastic material of 50 mm dia. The serclips used for assembly is of 17 mm dia. The foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x 0.3m below ground level and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint or duly powder coated of minimum 60 micron thickness. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment etc all. Rate inclusive of labour, material, taxes, transport, etc complete all. As directed by Engineer-in-Charge

Providing and Fixing Air Walker DIMENSIONS :- 1060mm (Length) x 810mm (Width) x 1600mm(Height). SAFE AREA: - 2.0 M x 1.8 M Air Walker Equipment made from “B” class G.I. Pipe of different NB. The main frame pipe is of 80mm NB made from “B” Class G.I. Material which is bend at the radius of 250mm. The bottom support of M.S. round plate of Ø250 mm & 10mm thick. The leg movement frame is of 32NB made from “B” Class G.I. pipe. This link is supported with MS flat of size 60X8mm. The handle frame is of 25NB made from “B” Class G.I. pipe. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “B” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. Closing Caps are made up of high quality Fiber reinforced Plastic material. Pins used of Diameter 25mm are made up from bright material. A24 circlips are used for assembly. The bearings used are “6205” permanent lubricated sealed bearing of repute brand likw SKF, FAG. High tensile steel galvanized nuts & bolts are used for assembly. The footrests are made from casted Aluminum material, having sizes 130mm X 310mm X 5mm thick. With the support of 250mm X 115mm X 3mm thick MS plate. To build structure bushes are used which are made from M.S.seamless pipe of 60mm O.D. and 5mm thickness as well as 60mm diameter solid bar bush is used. Bolt M8 X 16 mm and Nylock nut of M8 made of SS 304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust. The foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x 0.3m below ground level and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint or duly powder coated of minimum 60 micron thickness. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment etc all. Rate inclusive of labour, material, taxes, transport, etc complete all. As directed by Engineer-in-Charge

Providng and Fixing Sit Up Board Double PRODUCT DIMENSIONS: - 1950mm (L) x 1350mm (W) x 700mm (H). SAFE WORKOUT AREA: -2500mm (L)x 1600mm (W). The Sit up Board double made from “B” Class GI pipe. Make of G I Pipe will be of Tata, Jindal, Swastik, Zenith or Siddharth. The Sit up Board double made from “B” Class GI pipe. Center column made from 100mm NB “B” class G.I. Pipe. The remaining frame of the sit up board is of 50mm NB made from “B” class GI pipe. The powder coating is done with Fiber reinforced Plastic sheet of 3mm thickness is Bounded on 25mm NB (G.I.) “B” class pipe of mainframe. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “B” class Welded with M.S. round plate of Ø250 mm &10mm thick. Main pipe supported with 25mm X 25mm M.S. angles of 2mm thickness and 20mm x 40mm M.S. square pipes of 2mm thickness. The foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x 0.3m below ground level and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint or duly powder coated of minimum 60 micron thickness. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment etc all. Rate inclusive of labour, material, taxes, transport, etc complete all.As directed by Engineer-in-Charge

Providing and Fixing Pommel Horse DIMENSIONS :- 2000 mm (Length)x 690 mm (Width) x 640mm (Height). SAFEAREA :- 5 M x 3.5 Mr. Pommel horse equipment made from“B” Class G.I.pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. Make of G I Pipe will be of Tata, Jindal, Swastik, Zenith or Siddharth. The main frame of 80NB and 50NB made from“B”Class G.I. pipe. The handle frame is of 25NB made from “B” Class G.I. pipe. 20mm x 40mm MS square pipes frame is placed on the 25mm x 25mm X 2mm M.S. L Angle with 40 x 10mm thickness flat is used for support. High tensile steel with galvanized nuts and bolts are used for assembly. The foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x 0.3m below ground level and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint or duly powder coated of minimum 60 micron thickness. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment etc all. Rate inclusive of labour, material, taxes, transport, etc complete all. As directed by Engineer-in-Charge

Providing and Fixing Bench With Fixed Dumbells As directed by Engineer-in-Charge

Providing and Fixing Chest Press Cum Seated Puller As directed by Engineer-in-Charge

Providing and Fixing Combination 3 in 1 : Air Walker + Leg Press + Shoulder Builder As directed by Engineer-in-Charge

Providng and Fixing Horse Rider DIMENSIONS:-1180mm (Length) x 400mm (Width) x 1400mm. (Height). SAFEAREA: -2.2 Mtr x 1.4 Mtr. Horse rider equipment made from“B”class G.I. Pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe inmillimeters, Make of G I Pipe will be of Tata, Jindal, Swastik, Zenith or Siddharth. The main frame of 100NB made from “B” Class G.I. pipes welded with M.S. round plate of Ø250 mm &10mm thick, Seat provided are made up of MS deep draw quantity of 2mm thickness with no joint with uniform outer edge radius 20mm. The foundation used for fixingis a structure and made from center pipe of G.I. of 80 NB “B” class Welded with M.S. round plate of Ø250 mm &10mm thick. Main pipe supported with 25mm X 25mm M.S. angles of 2mm thickness and 20mm x 40mm MS square pipes of 2mm thickness. The leg movement frame is of 32NB made from “B” G.I.pipe. The handle frame is of 32 NB made from “B” Class G.I. pipe. The footrests are made from 25 NB “B” class G.I. pipe. Pins used of Diameter 17 mm are made up from bright material. The bearings used are “6203zz” permanent lubricated sealed bearing of reputed brand like SKF, FAG. High tensile steel with galvanized nuts &bolts are used for assembly. The circlips used for assembly are of A24mm. The foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x 0.3m below ground level and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint or duly powder coated of minimum 60 micron thickness. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment etc all. Rate inclusive of labour, material, taxes, transport, etc complete all. As directed by Engineer-in-Charge

Providing and Fixing Uneven Bar (OG-28) As directed by Engineer-in-Charge

Providing and Fixing Combination 3 in 1 : Leg Press + Standing Twister + Seating Twister (OG-29) As directed by Engineer-in-Charge

Providing and Fixing Knee Hip Riser (OG-38) As directed by Engineer-in-Charge

NET ROCK SCRAMBLER 1.5MTR (Proving and Fixing) Rec. Age :- 5-12 years The area :- 2.5m x 1.5m Safe play area :- 3.5m x 2.5m Height :- 1.5 M The rock n net climber is a combination of both rock and net climber. The platform of the rock climber is made up of 4 mm thick fiber reinforced plastic (FRP)/ROTO MOLDING( LLDPE /HDPE). The rocks are bolted on same platform, with a gradient of 65 degree from the ground. The main frame is made from 40 NB GI pipes. The net climber is made from 18 mm diameter nylon rope attached by specially designed nylon ball clamps. These ropes are attached to the pipe frame fabricated from 40 NB powder coated GI pipes with ‘U’ hooks. All pipes are ‘B’ class pipes The Foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x 0.45m and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint or duly powder coated of minimum 60 micron thickness. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment etc all. Work done should be as per engineer incharge.

S' SHAPED BRIDGE LADDER (Proving and Fixing) Rec. Age :- 4 - 12 yrs. The area :- 3.8 m x 2.1 m Safe play area :- 4.8 m x 3.1 m Height - 2.1 m The ‘S’ bridge is fabricated from 25 and 20 NB GI pipes. The vertical supports are made from 40 NB GI pipes with a total length of 2.1 m from the ground. It has two nos of ladder made from 40 NB GI pipes on the vertical support pipes itself. The steps of the ladder are made from 20 NB GI pipes. All pipes are ‘B’ class pipes The Foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x 0.45m and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint or duly powder coated of minimum 60 micron thickness. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment etc all. Work done should be as per engineer incharge.