Pune University Tender

Removing cement tiles, or marble or polished shahabad floor or dado without bed concrete including stacking the materials as directed with all leads, lifts, complete. Spec : As directed by Engineer In Charge

Removing cast iron or wrought iron or A.C. pipe and stacking them as directed with all leads, lifts, complete. Spec : As directed by Engineer In Charge

Removing rich mix cement concrete including stacking the spoils as directed with all leads, lifts, complete. Spec : As directed by Engineer In Charge

Removing doors and windows with frames and stacking the materials as directed with all leads, lifts, complete. Spec : As directed by Engineer In Charge

Removing ventilators and small windows with frame and stacking the materials with all leads lifts, complete. Spec : As directed by Engineer In Charge

Providing and laying Cast in situ/Ready Mix cement concrete in M-10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, formwork, laying/pumping,compacting, roughening them if special finish is to be provided,finishing if required and curing complete,with reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc.complete. With natural sand/V.S.I. quality Artificial Sand Bd. E. 1 Page No. 287

Providing and laying Cast in situ/Ready Mix cement concrete in M15 of trap/ granite/quartzite/gneiss metal for steps including steel centering, plywood/steel formwork, laying/pumping,compacting, roughening them if special finish is to be provided,finishing uneven and honeycombed surface and curing etc.complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface, only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc.(Wooden centering will not be allowed.),with reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc.complete. With natural sand/V.S.I. quality Artificial Sand Spec. No.: Bd.E.2 Page No. 288 and B.7 Page No 38

Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including centering, formwork, cover blocks, laying / pumping , compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand Spec. No.: Bd.F.6 Page No. 300 and B.7, Page No.38

Providing and fixing in position TMT-FE-500 reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. Spec. No: - Bd.F.17 Page No. 306

Providing second class Burnt Brick masonary with conventional/ I.S. type bricks in cement mortor 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding complete. Spec. No: - Bd. G.5 Page No.315

Providing and laying Cast in situ/Ready Mix cement concrete in M-20 of trap/ granite/ quartzite/ gneiss metal for R.C.C.coping to plinth or parapet and sill of doors and windows moulded as per detailed drawings or chamfered as approved by the Engineer including centering, formwork, cover blocks, laying/pumping, compacting , curing , finishing and roughening them if special finish is to be provided and curing complete.(Excluding reinforcement and structural steel).with reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand , Spec. No: - Bd. F.12 Page No.304 & B 7 Page 38

Providing and fixing chicken mesh jali (24 gauge) at the junction of 2 different surfaces of different material component at the time of plastering to prevent cracking in plaster surface as and where directed at all floors with all leads and lifts etc. complete. Spec. No.: As directed by Engineer in Charge:

Providing internal cement plaster 12mm thick in single coat in cement mortar 1:4 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing complete. Spec. No.: Bd. L.2 Page No. 368

Providing internal cement plaster 20mm thick in two coats in cement mortar 1:4 without neeru finish, to concrete, brick surface, in all positions including scaffolding and curing complete. Spec. No.: Bd.L.4 Page No. 368

Providing internal cement plaster 25mm thick in two coats in cement mortar 1:4 without neeru finish, to concrete, brick or stone surfaces, in all positions including scaffolding and curing complete. Spec. No.: Bd.L.5 Page No. 368

Providing neeru finish to plastered surfaces in all positions including scaffolding and curing complete. Spec. No.: Bd. L.10, Page No.370

Providing sand faced plaster externally in cement mortar using approved screened sand in. all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1 Kg. per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment of 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days, scaffolding etc. complete. Bd.L.7 Page No. 369

Providing and applying spray plaster made with finely graded marble and quartz in 2 mm thickness in two coats using putty knife or trowel to newly plaster fairly even surface after minimum 30 days gap in all position including finishing the surface using zero number sand paper or fine emry paper gently level the area by moving paper in round circles removing the dust and clean the surface with dry cloth and scaffolding including all materials and labour etc. complete.Spec. No.: As directed by Engineer in Charge.

Providing and fixing 40mm diameter and 1.5mm thick Stainless steel hand railing in S.S.304 Grade including fabricating ,fixtures, errecting , necessary welding , grinding , finishing, buffing to stainless steel pipe etc. complete.** Spec. No.: As directed by Engineer Incharge

Providing and fixing 900mm high S.S.304 Grade Stainless steel railing with 40mm diameter and 1.5mm thick at top,40mm diameter and 1.5mm thick vertical supports spaced at 1.5m center to center and 8mm thick toughened glass including fabricating ,fixtures, errecting , necessary welding , grinding , finishing, buffing to stainless steel pipe etc. complete.** Spec. No.: As directed by Engineer Incharge

Providing and fixing in position alluminium partly openable and partly fixed window of any size as per detailed drawing and as directed by Engineerin-charge with all necessary alluminium sections including necessary fixtures and fastening with 5 mm thick float glass etc. complete. b) With powder coating .Note – While arriving at the rate of item weight at 6.90 kg / Sqm is considered Spec. No: - As directed by Engineer in charge

Providing and fixing in position anodised (as per I.S.1868/1982) aluminium sliding window of three tracks with rectangular pipe having overall dimension 95 x 38 x 0.90 mm at weight 0.637 Kg/Rmt. and window frame bottom track section 92 x 31.75 x 1.30 mm at weight 1.07 Kg/Rmt. Top and side track section 92 x 31.75 x 1.30 mm at weight 0.933 Kg/Rmt. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 Kg/Rmt. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 Kg/Rmt. And handle section 40 x 18 x 1.25 mm at weight 0.417 Kg/ Rmt and top section 40 x 18 x 1.25 mm at weight 0.417 Kg/Rmt.as per detailed drawing and as directed by Engineer-In-Charge with all necessary aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass and alluminium mosquito net shutter with stainless steel jali with all required screws and nuts etc. complete. iv)With powder coating without box Spec. No: - As directed by Engineer in charge

Providing and fixing in position powder coated aluminium louvered windows / ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 x 38 mm x 1.22 mm box type, 5 mm thick sheet glass louvers, of approved quality etc. complete. Spec. No: - As directed by Engineer in charge

Providng and fixing in position anodised extruded aluminum partitions, partly glazed and partly laminated having frame made out of extruded tubular section of size 40 mm x 60 mm with 12 mm thick three layered flat pressed teak wood particle board bonded with BWP type exterior grade phenol formaldehyde synthetic resin conforming to IS 12823-1990, laminated on both sides,Novateakor equivalent and 5 mm thick selected quality plain/ float glass panels fixed withaluminum glass clips 12 mm x 12 mm and rubber cushioning beading to glass partitions as per approved drawing etc. compete Spec. No: - As directed by Engineer in charge

Providing and laying telephone black / Amba White / Cadburybrown / RBI red / Ocean Brown granite stone of 18 to 20 mm thick for door frame/ dado/ window boxing etc. On C.M. 1:6 including filling joints with polymer base filler nosing the sharp edges wherever necessary, curing, etc. complete. Specifications: As directed by Engineer in charge

Providing and laying in position flooring of telephone black / Amba White / Cat bary brown / RBI red / Ocean Brown granite stone of approved shade and size 18 mm to 20 mm thick on bed 1:6 cement mortar including cement floats striking joints, pointing in C.M. 1:3 curing and cleaning etc. complete. Spec. No: - Bd. M . 3B Page No. 380

Providing and fixing machine cut machine polished 18 mm to 20 mm thick telephone black / Amba White / Cat bary brown / RBI red / Ocean Brown granite stone for treads and risers of steps and staircases of approved colour and shade with rounded moulding and three grooved line for the treads on bed of 1;4 Cement mortar including float filling joints with neat cement slurry curing polishing and cleaning etc. complete. Spec. No.: Bd. M.22 B/Page No. 390

Providing and fixing machine cut mirror polished 18 mm to 20 mm thick telephone black granite / Amba White / Cat bary brown / RBI red / Ocean Brown granite stone partition with rounding the edges etc. complete . Both side polish

Providing Half-round Moulding ( Full Moulding ) to 18 mm to 20 mm thick granite stone including fine polishing and cleaning etc complete.Spec.No:As directed by Engineer In Charge

Providing and laying vitrified mirror / glossy finish tiles decorative type RAK/ Kajaria/ Nitco/ Asian or equivalent make having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 ( group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete. a) Flooring , Spec. No.: Bd.M. 12 Page No.385

Providing and laying vitrified mirror / glossy finish tiles of RAK/ Kajaria/ Nitco/ Asian or equivalent make having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 ( group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete. b) Skirting Spec. No.: Bd.M. 12 Page No.385

Providing and laying vitrified matt fininsh tiles of RAK/ Kajaria/ Nitco/ Asian or equivalent make having size 590 mm to 605 mm x to 605 mm of 8 to 10 mm thickness and confirming IS. 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement morar including neat cement float, filling joints, curing and cleaning complete a) flooring Spec. No.: Bd.M.12 Page No. 385

Providing and laying vitrified matt finish tiles of RAK/ Kajaria/ Nitco/ Asian or equivalent make having size 590 mm to 605 mm x to 605 mm of 8 to 10 mm thickness and confirming IS. 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and cleaning complete. b) Skirting Spec. No.: Bd.M.12 Page No. 385

Providing and fixing 1.5 mm thick polyvenyl venyl chloride flooring including leveling the base with white cement including pasting with appropriate material cleaning the surface etc. complete

Providing and applying priming coat on concrete/ masonary/ Asbestos Cement plastered surfaces including scaffolding if necessary, preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and sand papering as required. Spec : As directed by Engineer In Charge

Providing and applying priming coat over new wood and wood based surfaces, including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter, sand papering and knotting, scaffolding etc. complete.Spec : As directed by Engineer In Charge.

Providing and applying priming coat over new/old steel and other metal surfaces including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and scoured with wire brushes, fine steel wool, scrappers and sand paper, scaffolding etc. complete.Spec : As directed by Engineer In Charge

Providing and applying washable oil-bound distemper of approved colour and shade to old and new surfaces in two coats including scaffolding, preparing the surfaces. (excluding the primer coat.) etc. complete.Spec. No: - Bd P. 5 Page No. 413

Providing and applying two coats of synthetic enamel paint of approved colour to new /old structural steel work and wood work in buildings, including scaffolding if necessary, cleaning and preparing the surface (excluding primer coat) complete.Spec. No.: Bd.0.5 Page No. 405

Providing and applying two coats of APEX exterior paint of approved manufacture and of approved colour to the plastered surface including cleaning and preparing the surfaces, applying priming coat, scaffolding if necessary, watering the surfaces for two days complete. Spec :- As directed by Engineer in charge.

Providing and applying pearl/ luster finish paint of approved colour and shade to the existing plaster surface including scaffolding, preparing the surface, applying the acrylic wall putti etc. complete.Spec : As directed by Engineer In Charge

Providing and applying 2 coats of flat oil paint of approved colour and shade to internal / external plastered surfaces including scaffolding if necessary, cleaning and preparing the surface (excluding primer coat) complete.Spec. No.: Bd.0.7 Page No. 406

Providing and fixing false ceiling with eco-friendly light-weight calcium silicate tiles of spintone surface texture aerolite make or equivalent of size 595mm x 595mm having 15mm thick densified micro look edge and 100% humidity resistance incombustible as per BS 46part IV and thermal conductivity 0.043 w/m 0 KC and NRC 0.50 placed in true horizontal level suspended grid of size 600x600mm made from hot dipped G.I. steel sections ion silhouette profile, rotary stitched double webbed white with 6mm reveal profile (white/black), wherein, main T runner of size 42mmx14mm between main tee 600mm center-tocenter and secondary cross T of size 33x14x0.43mm thick of length 600mm long spaced inter-locked at middle of the first crossed T in each panel to form grid of 1200mmx600mm resting on periphery wall Profile wall section 19mm (7+7) x 19mmx0.40thicknesses and laying false ceiling for services like diffusers grills including cutting, making opening for light fittings, fixtures, , smoke detectors etc., wherever required. Main T runners suspended from ceiling with using G.I. soffit cleats of size 25x35x1.6 mm of required length fixed to the ceiling with 6mm dia and 50mm long dash fastener, 4mm dia G.I. adjustable rods with powder-coated/good quality G.I. level adjustment clips of 35x35x0.8mm spaced @1200, center-tocenter along main T all complete at all heights as per the As directed by Engineer in charge.

Providing and fixing false ceiling of 15mm thick Acoustic tubular Armstrong/ Everest/ AMS (0.60 x 0.60 m.) boards of approved make, shape and sizes as per drawings including powder coated G.I. wall angle of 20mm x 20mmx 0.6 x 0.6mm size, G.I. grid runners of size 15mm x 38mm at 600mm center to center both ways and suspended using G.I. 3mm wire including fixing using butterfly clips and fasteners including transporting, scaffolding all necessary labour and machinery, finishing etc. complete. Spec :As directed by Engineer in charge.

Providing and fixing on walls / ceiling / floors, ------------ mm dia heavy grade having embossed as ISI mark galvanized iron pipes with necessary fitting, remaking good the demolished portion and with primer of anti corrosive oil paint 2 coats complete.a) 15 mm dia at 1.48 kg/meter,Bd.V.5 Page No. 551

b) 20 mm dia at 1.93 kg/meter

c) 25 mm dia at 3.01 kg/meter

d) 32 mm dia at 3.89 kg/meter

d) 40 mm dia at 4.49 kg/meter

f) 50 mm dia at 6.33 kg/meter

Providing and fixing ---- mm dia stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc.complete Spec. No: - As directed by Engineer in charge.A) 75 mm dia. Pipe

B) 100 mm dia. Pipe

Providing and fixing P.V.C. Rain water pipes of 110mm outer diameter and having wall thickness of 2.2 to 2.7 mm confirming to I.S. 13592-1992 including proper rainwater receiving recess with P.V.C. plug, bend, necessary fittings, such as, offsets, shoes,inluding fixing the pipe on wall using approved wooden cleats projecting 25mm to 40mm from face of wall a fixing with clips of approved quality and number ,filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on C.C. or masonry blocks, including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations of pipes. All the P.V.C. fittings and additional 2 piece socket clips shall be got approved from engineer in charge etc. complete. (The contractor shall give 3 yrs guarantee bond for payment).Spec.No. As directed by Engineer-in-charge

Providing and fabricating structural steel work in rolled sections like joists, channels, angles, tees etc. as per detailed designs and drawing including fixing in position without connecting plates, braces etc. and one coat of anticorrosive paint and over it two coat of oil paintings of approved quality and shade complete. Spec. No: - Bd.-C 2 Page No. 275

Providing, fabricating and erecting at site of work the tubular steel structure (shed) as per standard design and specifications having various spans in between trusses and in multiples of standard length of bays as specified as per standard specifications, inclusive of cost of steel tubular trusses, tubular columns purlins, tie runners, foundation bolts, base plates, nuts and bolts, welding wherever required etc. as per detailed drawing inclusive of one coat of anticorrosive paint and two coats of oil painting of approved quality and shade etc.complete. Spec. No. : As directed by Engineer-in-charge. And B-18 Page No. 78

Side Tables Providing and fixing in position loose side table of size 0.6 x 0.38 x 0.4(HT) with 1 drawer as shown in drawing …. using 19mm Plywood & 19mm ply patti for 38 mm thk top & sides in double 19 mm ply for sides , 19 mm ply for back finished with 1mm thk laminate from inside & outside as show drawing . Drawer Fascia to be made in 19mm ply with 1mm thick laminate (range @ Rs.615/ sqm.)and sides of drawer is to be made in 12mm ply finished with 0.8mm thick laminate from inside & outside & base is to be made in 6 mm finished with 0.8mm laminate from inside & outside. The Drawer shall be provided with handles (Stainless Steel finish) and telescopic channels(12”) as per approval . All exposed plywood surfaces are to be finished with 1 mm thick laminate(range @ Rs.615/ sqm.) & all internal surfaces in 0.8 mm thk laminate(range @ Rs.260/ sqm.) of approved make & shade and all exposed edges of plywood to have 25mm x 6mm , 50mm x 6 mm thk for top edge BTC lipping. All internal exposed wooden sections to be MELAMINE POLISH in matching colour of laminate. Rate inclusive anti termite treatment to the wooden &plywood material. Item to include all necessary hardware and fittings in Stainless Steel matt finish,4” handle multi purpose locks including magnetic ball catcher, Hinges( L/W),fevicol, screws etc.,as per instruction of site engineer in -charge , complete in all respects.

Wardrobe Providing and fixing in position Wardrobe of size 1.5 x 0.45 X 2.1(HT) as per drawing ., by using 19mm and 19mm ply patti for 38mm thk top finished by 1mm laminate at edge , 0.8 mm thk laminate at above top and 19 mm thick plywood for all other horizontal and vertical sides & internal shelf, 12 mm ply for back finished by 0.8 mm thk laminate from inside, as shown in the drawing .Drawer Fascia is to be made in 19mm ply with laminate and sides of drawer are to be made in 12mm ply , 6mm ply for back finished with 0.8 mm thk laminate from inside & outside, as shown in the drawing . The drawer shall be provided with 4”handles (Stainless Steel finish) and telescopic channels(16”) as per approval. Shutter is to be made in 12mm ply patti of 0.15 wide sandwiched by 6mm ply from both side finish with0.8mm laminate from inside & 1mm laminate from out side , Shutters all edges to have 2" x 1/2" BTC lipping having 8”handles (Stainless Steel matt finish -1no for each shutter) and fixed by 4-no of s.s matt hinges for each shutter ,as per approval & as shown in the drawing . All exposed plywood surfaces are to be finished with 1 mm thick laminate (range @ Rs.615/ sqm.)& all internal surfaces in 0.8 mm thk laminate(range @ Rs.260/ sqm.) ( .....) of approved make & shade and all exposed edges of plywood to have 25mm x 6mm , 50mm x 6 mm thk for top edge BTC lipping. All internal exposed wooden sections to be MELAMINE POLISH in matching colour of laminate. Rate inclusive anti termite treatment to the wooden &plywood material. Item to include all necessary hardware and fittings in Stainless Steel matt finish,2 no of ready made wall mounted hanger stand ( as per specification) 4 no-4”, 4 no of 8” handle ,2 no of multi purpose drawer locks & 2 no of shutter lock including magnetic ball catcher,6"tower bolts(2 no for each shutter), chain(1 no for each shutter)(1 no for each shutter)(1 no for each shutter),Hinges( L/W),wall mounted hanger , fevicol, screws etc.,as per instruction of site engineer in -charge , complete in all respects.

Workstation Providing and fixing in position Workstation of 2.0 x 0.6 x0.75m ht , by using 19mm and 19mm ply patti for 38mm thk top & sides , 12 mm ply for back. Telescopic CPU Stand/ ready made Keyboard tray shall be provided of approved model and make. Storage ( 0.45 x 0.6 x 1 no) of 1 drawer & 1 shutter for each as per drawing shall be provided. Drawer Fascia to be made in 19mm ply with 1mm thk laminate and sides & base of drawer is to be made in 12mm ply finished with 0.8mm thk laminate from inside & outside, bottom in 6 mm ply finised by 0.8 mm thk laminate from inside & outside as shown in the drawing . Shutter in 19 mm ply finished by 1 mm thk laminate fixed by 2 no of W-hinges. Internal shelf in 19mmply. Shutter shall be provided with 1 no of 4” handles (Stainless Steel finish) and telescopic channels(18”) as per approval of the Architect. Etc., complete in all respects and as per instruction of engineer-in-charge. Item to include plywood box of size 2.0 x 0.15 x 0.05 m thk , 0.6x 0.1 x 0.05 x 2no for switchboard , made in 19 mm ply finished by 1mm thk laminate & 12mm ply for back , all internal vertical & horizontal frame support in 19 mm plywood. Etc., as shown in the drawing ,as per instruction of site engineer in -charge , complete in all respects. Item to include foot rest of size 0.45 x 0.20 x 0.08 m(ht) x 2 no , made in 19 mm ply finished by 1mm thk laminate from outside . Etc., as shown in the drawing ,as per instruction of site engineer in -charge , complete in all respects. All exposed plywood surfaces are to be finished with 1 mm thick laminate(range @ Rs.615/ sqm.) & all internal surfaces in 0.8 mm thk laminate(range @ Rs.260/ sqm.)( ( .....) of approved make & shade and all exposed edges of plywood to have 25mm x 6mm , 50mm x 6 mm thk for top edge BTC lipping. All internal exposed wooden sections to be MELAMINE POLISH in matching colour of laminate. Rate inclusive anti termite treatment to the wooden &plywood material.Item to include all necessary hardware and fittings in Stainless Steel matt finish, ,1no of multi purpose drawer locks& 1no of shutter lock including magnetic ball catcher,Hinges( L/W),tower bolts, chain(1 no for each shutter)(1 no for each shutter),hinges,wall mounted hanger , fevicol, screws etc.,as per instruction of site engineer in -charge , complete in all respects. Note: This item includes Table(2 x 0.6 x0.75 m htx 1 no) & plywood boxing( 2 x 0.15 x 0.08m thk x 1no , 0.6x 0.1 x 0.05 x 2no ),footrest (0.45 x 0.3 mx 0.08mht x 2 no)

Pelmet for curtain ( +6” From wall) Providing and fixing 12mm thk plywood boxing consisting of the following items. Mode of measurement to be Length of Boxing x height Providing and constructing in proper line and level, vertical L- type framework in 19 mm ply fixed on to wall @ 600mm c/c both ways by means of approved wooden screws to give the required thickness as per drawings .Rate inclusive 0.8 mm thk laminate for internal exposed surface as shown in the drawing. All exposed plywood surfaces are to be finished with 1 mm thick laminate(range @ Rs.615/ sqm.) & all internal surfaces in 0.8 mm thk laminate(range @ Rs.260/ sqm.) ( .....) of approved make & shade and all exposed edges of plywood to have 25mm x 6mm , 50mm x 6 mm thk for top edge BTC lipping. All internal exposed wooden sections to be MELAMINE POLISH in matching colour of laminate. Rate inclusive anti termite treatment to the wooden &plywood material. Item to include all necessary hardware and fittings in Stainless Steel matt finish, fevicol, screws etc.,as per instruction of site engineer in -charge , complete in all respects.

Low ht storage ( Ht- 0.75 M)(deep- 0.45m) Providing and fixing in position Low Height Storage of ht 0.75 M as shown in drawing ...item also include 38mm thk ledge made in 19 mm ply & 19 mm ply patti as shown in drawing finished with 1mm laminate...all other vertical & horizontal surfaces,shelf made by using 19mm Plywood & 12mm thk ply for back. Shutter is to be made in 19mm ply finish with0.8mm laminate from inside & 1mm laminate from out side, having 4”handles (Stainless Steel matt finish) and fixed by 2-no of s.s matt hinges for each shutter ,as per approval & as shown in the drawing . All exposed plywood surfaces are to be finished with 1 mm thick laminate (range @ Rs.615/ sqm.)& all internal surfaces in 0.8 mm thk laminate(range @ Rs.260/ sqm.) ( .....) of approved make & shade and all exposed edges of plywood to have 25mm x 6mm , 50mm x 6 mm thk for top edge BTC lipping. All internal exposed wooden sections to be MELAMINE POLISH in matching colour of laminate. Rate inclusive anti termite treatment to the wooden &plywood material. Item to include all necessary hardware and fittings in Stainless Steel matt finish, 4” handle , locks& shutter lock including magnetic ball catcher,tower bolts(2 no for each shutter), chain(1 no for each shutter)(1 no for each shutter),hinges,wall mounted hanger , fevicol, screws etc.,as per instruction of site engineer in -charge , complete in all respects.

O.H.S storage ( Ht- 0.6M)(deep- 0.40m) Providing and fixing in position over head storage of ht 0.6 M as shown in drawing ...item also include 38mm thk ledge made in 19 mm ply & 19 mm ply patti as shown in drawing finished with 1mm laminate at edge & 0.8 mm thk laminate above top & bottom is finished by 0.8mm thk laminate from inside & 1mm thk laminate from outside. as shown in the drawing...all other vertical & horizontal surfaces,shelf made by using 19mm Plywood & 12mm thk ply for back. Shutter is to be made in 19mm ply finish with0.8mm laminate from inside & 1mm laminate from out side, having 4”handles (Stainless Steel matt finish) and fixed by 2-no of s.s matt hinges for each shutter ,as per approval & as shown in the drawing . All exposed plywood surfaces are to be finished with 1 mm thick laminate(range @ Rs.615/ sqm.) & all internal surfaces in 0.8 mm thk laminate(range @ Rs.260/ sqm.) ( .....) of approved make & shade and all exposed edges of plywood to have 25mm x 6mm , 50mm x 6 mm thk for top edge BTC lipping. All internal exposed wooden sections to be MELAMINE POLISH in matching colour of laminate. Rate inclusive anti termite treatment to the wooden &plywood material. Item to include all necessary hardware and fittings in Stainless Steel matt finish, 4” handle , locks& shutter lock including magnetic ball catcher,tower bolts, chain(1 no for each shutter)(1 no for each shutter),hinges,wall mounted hanger , Hinges( L/W),fevicol, screws etc.,as per instruction of site engineer in -charge , complete in all respects.

Providing and fixing in position Meeting table of 1.0 x 1.0 mx 0.75m ht... , Top of 75 mm thk made in 19 mmply & 19 mm ply patti . 19mm for all other vertical support cladded with 1mm thk laminate as shown in the dwg, complete in all respects.Item also include 12 mm thk toughen clear glass top with crystal edge polish of 1.03 m x 1.03 m is to be layed on 19mm dia transparent glass catcher , glass with edge polish,details as per drawing. Complete in all respect. Rate inclusive pebbles for nitch as shown in the drawings as directed by Engineer incharge /ArchitectAll exposed plywood surfaces are to be finished with 1 mm thick laminate(range @ Rs.615/ sqm.) & all internal surfaces in 0.8 mm thk laminate(range @ Rs.260/ sqm.) ( .....) of approved make & shade and all exposed edges of plywood to have 25mm x 6mm , 50mm x 6 mm thk for top edge BTC lipping. All internal exposed wooden sections to be MELAMINE POLISH in matching colour of laminate. Rate inclusive anti termite treatment to the wooden &plywood material. Item to include all necessary hardware and fittings in Stainless Steel matt finish, handle , locks& shutter lock including magnetic ball catcher,tower bolts, chain(1 no for each shutter)(1 no for each shutter),hinges,wall mounted hanger , Hinges( L/W),fevicol, screws etc.,as per instruction of site engineer in -charge , complete in all respects.

Staff Table with side unit Providing and fixing in position staff Table of size 1.55 x 0.6x 0.75m ht as per …,Table by using 19mm &19mm ply patti for 38mm thk top and 19 mm thick plywood for all other horizontal and vertical members, (as per drawing) Telescopic channel CPU Stand/ ready made Keyboard tray shall be provided of approved model and make. Footrest made in 18mm ply as per dwg. Table is having Storage of 0.45 x 0.6 x 0.75ht x 1 no with 1 drawer & 1 shutter as per drawing shall be provided. Drawer Fascia to be made in 19mm ply with 1mm thk laminate from outside 0.8 mm thk laminate from inside and sides & back of drawer is to be made in 12mm ply & bottom in 6mm ply finished with 0.8mm thk laminate laminate from bothside . Shutter in 19 mm ply finished by 1 mm thk laminate fixed by 2 no of W-hinges, 2 no of 4” handles (Stainless Steel finish) and telescopic channels(18”) as per approval . Side unit (0.9 x 0.4) of 2 drawer & 2 shutter as per drawing shall be provided. Back in 12 mm ply .Drawer Fascia to be made in 19mm ply with 1mm thk laminate from outside 0.8 mm thk laminate from inside and sides & back of drawer is to be made in 12mm ply & bottom in 6mm ply finished with 0.8mm thk laminate from bothside. Shutter made in 19mm ply finished with 1mm thick laminate as shown in the drawing and all other sides shall be finished with 0.8 mm thk laminate, as per drawing.All exposed plywood surfaces are to be finished with 1 mm thick laminate (range @ Rs.615/ sqm.)& all internal surfaces in 0.8 mm thk laminate(range @ Rs.260/ sqm.) ( .....) of approved make & shade and all exposed edges of plywood to have 25mm x 6mm , 50mm x 6 mm thk for top edge BTC lipping. All internal exposed wooden sections to be MELAMINE POLISH in matching colour of laminate. Rate inclusive anti termite treatment to the wooden &plywood material. Item to include all necessary hardware and fittings in Stainless Steel matt finish, handle , locks& shutter lock including magnetic ball catcher,tower bolts, chain(1 no for each shutter)(1 no for each shutter),hinges,wall mounted hanger ,Hinges( L/W), fevicol, screws etc.,as per instruction of site engineer in -charge , complete in all respects. Note: This item includes table (1.55 x 0.6 x0.75m ht x 1 no with storage 0.45x0.6 x0.75mhtx1no)) , side unit (0.9x 0.45x 0.75mht),footrest (0.45x0.3x 0.08mht x 1no)

Providing and fixing Suspended ceiling, which includes GI perimeter channels (having one flange of 20mm and another flange of 30mm and a web of 27mm) along the perimeter of ceiling, screw fixed to brick wall/partition with the help of nylon sleeves and screws, at 610mm centres. Then suspending GI intermediate channels of size 45mm (with two flanges of 15mm each) from the soffit at 1220mm centres with ceiling angle of width 25mmx10mm fixed to soffit with GI cleat and steel expansion fasteners. Then GI Ceiling section of having web of 51.5mm and two flanges of 26mm each with lips of 10.5mm are then fixed to the intermediate channel with the help of connecting clip and in direction perpendicular to the intermediate channel at 457mm centres. Single layer of 12.5mm tapered edge Gypboard® Plain (conforming to IS 2095 part 1 1996) is then screw fixed to ceiling section with 25mm drywall screws at 230mm centres. Screw fixing is done mechanically either with screw driver or drilling machine with suitable attachment. Finally square and tapered edges of the boards are to be jointed and finished so as to have a flush look which includes filling and finishing with Jointing compound, Joint Paper tape and two coats of Drywall Top Coat (as per recommended practices of manufacturer. Rate to be included all kinds of profiles and cut outs required for light fixtures, Speakers, Smoke detector, trap doors and AC grill in the ceiling.

SOLID PARTITON WITH GLASS PANEL-Type A Providing & fixing in position, full height partly glass panelled & partly solid partition made of treated Burma Teak wood framework of size 38mm x 50mm having grid spacing at 600mmx600mm centre to centre both ways & covered with 12 mm thick Marine BWP (boiling water proof) plywood on both sides of framework & finished with 1mm thick laminate of approved color and texture. The framework shall be properly screwed to the walls, ceiling and floor and plywood shall be screwed to the framework. The space between the framework grid shall be filled with glass wool for sound insulation. The partition will have an opening as per the height specified in the drawing. Glass of thickness 12 mm will be fixed in the opening with wooden beading of size 38mm x 12 mm on both sides. Wooden beadings will be finished in three or more coats of melamine polish (glossy/matt) including final coat of buffing till the required finish is achieved . Provision shall be made for necessary cutouts for services such as wire management etc. as per design including all necessary hardware & accessories, grooves, adhesives, cutting & making good the original surfaces on completion. All material shall be of approved make. All works complete as per the drawing, specification and direction of the Engineer. (Refer drawing number - IN - 601)

SOLID PARTITON WITH GLASS PANEL-Type B Providing & fixing in position, full height partly glass panelled & partly solid partition made of treated Burma Teak wood framework of size 38mm x 50mm having grid spacing at 600mmx600mm centre to centre both ways & covered with 12 mm thick Marine BWP (boiling water proof) plywood on both sides of framework & finished with 1mm thick laminate of approved color and texture. The framework shall be properly screwed to the walls, ceiling and floor and plywood shall be screwed to the framework. The space between the framework grid shall be filled with glass wool for sound insulation. The partition will have an opening as per the height specified in the drawing. Glass of thickness 12 mm will be fixed in the opening with wooden beading of size 38mm x 12 mm on both sides. Wooden beadings will be finished in three or more coats of melamine polish (glossy/matt) including final coat of buffing till the required finish is achieved . Provision shall be made for necessary cutouts for services such as wire management etc. as per design including all necessary hardware & accessories, grooves, adhesives, cutting & making good the original surfaces on completion. All material shall be of approved make. All works complete as per the drawing, specification and direction of the Engineer. (Refer drawing number - IN - 601)

SOLID PARTITION WITH ALUMINIUM JAALI PANEL Providing & fixing in position, full height partly panelled & partly solid partition made of treated salwood framework of size 38mm x 50mm having grid spacing at 600mmx600mm centre to centre both ways & covered with 12 mm thick Marine BWP (boiling water proof) plywood on both sides of framework & finished with 1mm thick laminate of approved color and texture. The framework shall be properly screwed to the walls, ceiling and floor and plywood shall be screwed to the framework. The space between the framework grid shall be filled with glass wool for sound insulation. The partition will have an opening as per the height specified in the drawing. Aluminum Jaali of thickness 12 mm will be fixed in the opening with wooden beading of size 38mm x 12 mm on both sides. Wooden beadings will be finished in three or more coats of melamine polish (glossy/matt) including final coat of buffing till the required finish is achieved . Provision shall be made for necessary cutouts for services such as wire management etc. as per design including all necessary hardware & accessories, grooves, adhesives, cutting & making good the original surfaces on completion. All material shall be of approved make. All works complete as per the drawing, specification and direction of the Engineer. (Refer drawing number - IN - 601)

DEAD PARTITION Providing & fixing in position full height solid partition made out of treated Burma Teak wood framework of size 38mm x 50 mm having grid spacing at 600mm x600mm center to center both ways & covered with 12 mm thick Marine BWP (boiling water proof) plywood on both sides of framework & finished with 1mm thick laminate of approved color and texture. The framework shall be properly screwed to the walls, ceiling and floor and plywood shall be screwed to the framework. The space between the framework grid shall be filled with glass wool for sound insulation. Provision shall be made for necessary cutouts for services such as wire management etc. as per design including all necessary hardware & accessories, grooves, adhesives, cutting & making good the original surfaces on completion. Provision shall be made for wire management to take care of basic wiring requirement for providing power data- voice switches on a modular switch plate. All material will be of approved make. All works complete as per the drawing, specification and direction of the Engineer.

Providing and making Holes (Core cutting ) in chajjas and slab for passing the pipe line. Spec. No: - As directed by Engineer in charge

Providing and making Holes (Core cutting ) in U.C.R. wall for passing the pipe line. Spec. No: - As directed by Engineer in charge

Rebaring work , a) 8 mm

b) 12 mm

c) 16 mm

Material Shifting by truck Spec. No: - As directed by Engineer in charge

Mazdoor, Unskilled Heavy Male/Female Spec. No: - As directed by Engineer in charge

Providing Carpenter I Class Skilled Spec. No: - As directed by Engineer in charge

BASIC TEST OF CEMENT. Standard Consistancy, Fineness, Specific 1 Gravity, Setting Time ( Initial & Final ) Compressive Strength, Soundness

PLYWOOD \ Determination of Resistance to dry heat,Determination of Moisture Content , Determination of Density , Thickness of Plywood.

Test for Glue Adhesion

CERAMIC TILES I VITRIFIED TILES , Water Absorption, Modulus of Rupture (Set of 6 Tiles)