Public Works Department Tender

FREE STANDING TABLE @ 1800LX750DX750HT WITH SIDE COMBO STORAGE @ 1200LX450DX750HT Supply, Fitting & Fixing of SOS Make Prelam Cabin. Work Top- Shall be made up of Work top shall be made 25mm thick Prelam (OSL) particle board confirming to IS 12823: 1990 with 2mm thick PVC lipping glued with Kliberit-779.6 glue. Work top is under goes from distributed load test for deflection by applying 0.027kg/mm load on Top and concentric load test by applying 90kg load on weaker section Understructure- Modesty panel shall be made of 18mm thick Prelam BSL particle board confirming to IS 12823: 1990 with 2mm thick PVC lipping glued with Kliberit-779.6 glue. Gable ends shall be made of 25mm thick Prelam BSL particle board confirming to IS12823: 1990. The construction shall be aesthetically appealing completely knock down construction fitting is done by using the Minifix & Dowels. Gable end height will be 725mm and its depth varies as per the depth of work top. Standard depth of work top will be 600mm and 750mm. Wire management- Wire manager cap on the table top shall be made of ABS material having Diameter 63.5mm standard.The product must be from a Manufacturer having ISO 9001,ISO 14001,Latest BIFMA 5.1 certificates for few of its products. SIDE COMBO STORAGE @ 1200LX450DX750HT. TOP: 25MM Thick Prelaminated Partical Board with 2MM PVC edge band on all edges CARCASS (Body/ Shutter / Back) : 18MM thick Prelaminated Partical Board with PVC edge band on all exposed edges. SHELF : Adjustable shelf made of 18MM thick Prelaminated Partical Board with PVC edge band on all edges 2 BOOK + 1 FILE DRAWER & SHUTTER : Facia/Shutter Made up of 18MM thick Prelaminated Partical Board with 2MM PVC edge band on all edges. Drawers made up of CRCA finished in Powder coating. HARDWARE : Imported Telescopic Slides, Hettich Hinges & Lock.

PRELAM STORAGE @ 1050LX450DX750HT Supply, Fitting & Fixing of SOS Make Prelam Storage. Storage Top- Shall be made of 25mm thick Prelam (OSL) particle board for low height Prelam storage up to 750 Height and above 750mm height 18mm Thick prelam (OSl) particle board is used. Both the 25mm and 18mm thick Prelam (OSL) particle board confirming to IS 12823: 1990 with 2mm thick PVC lipping glued with Kliberit-779.6 glue. Storage top is under goes from distributed load test for deflection by applying 0.027kg/mm load on Top and concentric load test by applying 90kg load on weaker section. Load carrying capacity of 18mm thick shelf shall be 25kgs UDL. Storage Body- The construction shall be aesthetically appealing completely knock down construction .side panel and back panel is made from 18 mm Prelam (OSL) particle board conforming to IS 12823:1990;. All the exposed edges are with 2mm PVC lipping& sealed edges are with 0.8mm thick PVC Lipping. Both the LH & RH side panel and back panel are connected with each other by using fittings such as Minifix & Dowels. Shelf can be made up of 18mm Prelam (BSL) particle board confirming to IS 12823: 1990 with 2mm thick PVC lipping glued with Kliberit-779.6 glue. Shelf is mounted on shelf pin and self-height can be adjusted with in the limit. Prelam Shutter- The complete storage shall have two shutters of 18mm thick Prelam (OSL) particle board confirming to IS 12823: 1990 with 2mm thick PVC lipping glued with Kliberit-779.6 glue and are hinged shutter with equal width hung with 0 Crank on side panel and 9.5 crank hinges on middle vertical panel. C type SS brush finish handle is used in both the shutter of 96mm CD(center to center distance handle hole)and Hettich make. Black color PVC door strip and multi-purpose square lock (Hettich or Ebco) is used

FREE STANDING TABLE @ 2400LX600DX750HT Supply, Fitting & Fixing of SOS Make Prelam Cabin. @ 2400LX600DX750HT. Work Top- Shall be made up of Work top shall be made 25mm thick Prelam (OSL) particle board confirming to IS 12823: 1990 with 2mm thick PVC lipping glued with Kliberit-779.6 glue. Work top is under goes from distributed load test for deflection by applying 0.027kg/mm load on Top and concentric load test by applying 90kg load on weaker section Understructure- Modesty panel shall be made of 18mm thick Prelam BSL particle board confirming to IS 12823: 1990 with 2mm thick PVC lipping glued with Kliberit-779.6 glue. Gable ends shall be made of 25mm thick Prelam BSL particle board confirming to IS12823: 1990. The construction shall be aesthetically appealing completely knock down construction fitting is done by using the Minifix & Dowels. Gable end height will be 725mm and its depth varies as per the depth of work top. Standard depth of work top will be 600mm and 750mm. Wire management- Wire manager cap on the table top shall be made of ABS material having Diameter 63.5mm standard.The product must be from a Manufacturer having ISO 9001,ISO 14001,Latest BIFMA 5.1 certificates for few of its products.

PUBLIC SEATING CHAIR - 3 SEATER Providing and Fixing 3 seater Public seating chair made of complete metal with Legs in Crome finish and seates in silver powder coating finish.

SLOTTED ANGLE RACK @900LX600DX2100HT. Slotted angle- Slotted angle is made up 2mm thick CRCA sheet confirming the IS grade IS 513:2008 coated with final finish consisting of epoxy polyester powder coat of approved color & shade with a Dry Film Thickness of minimum 50 to 60 microns. Angle length is equivalent to the height of the storage which is approx. 2100mm or 1830mm Shelf-Is made up of 0.8mm CRCA sheet confirming the IS grade IS 513:2008. All the four edge is having a bend of 25mm. Shelf is supported by T-Hat in the middle portion. T-hat is made up of 0.8mm CRCA sheet confirming the IS Grade IS 513:2008.Each shelf is having loading carrying capacity of 18kg UDL and total load carrying capacity of unit is 50kg UDL. Finish- The bodies including shelves are given anti-rust surface treatment & are powder coated with epoxy polyester powder. It involves an Oxsilan pre-treatment consisting of Hot water degreasing, cold water rinse I & cold water rinse II, iron phosphate, cold water rinse, and passivation & dry off oven treatment. Final finish consists of epoxy polyester powder coating of approved color & shade with a Dry Film Thickness of 50 to 60 (+\- 5) microns. The material is then oven baked with a controlled temperature of 180 deg.C to 200 deg.C. Fasteners:- Assembly is done with the help of M8 NUT nuts & HEX BOLT M8 X 16.

2 BAY COMPACTOR @ 2115 HEIGHT COMPACTOR 2 BAY / SINGLE FACE FIX UNIT/WITHOUT SHUTTER @ 1830WX381DX2115H

2 BAY COMPACTOR @ 2115 HEIGHT COMPACTOR 2 BAY / SINGLE FACE MOBILE UNIT/WITHOUT SHUTTER @ 1830WX381DX2115H

2 BAY COMPACTOR @ 2115 HEIGHT COMPACTOR 2 BAY / DOUBLE FACE MOBILE UNIT/WITHOUT SHUTTER @ 1830WX762DX2115H

COMPACTOR FLOOR RAIL PER FEET Supply and installation of SOS make Compactor Storage System Main Body: Rigid Knock Down construction made out of 0.8mm thk. CRCA Steel conforming to IS: 513 Grade. Each body block (SFF/SFM/DFM) building consists of 1 Main unit & then Add-on units ( 1, 2, 3, 4 - depending on no. of bays 2, 3, 4 & 5). Each unit has 5 loading levels formed by 4 nos. adjustable shelves. Body units are bolted to undercarriage.Compactor Height from ground is 2080 mm (1980 body + 100 under-structure + 35 channel system). SFF- SINGLE FACE FIX UNIT SFM- SINGLE FACE MOBILE UNIT DFM- DOUBLE FACE MOBILE UNITFinish- The bodies including shelves are given anti-rust surface treatment & are powder coated with epoxy polyester powder. It involves an Oxsilan pre-treatment consisting of Hot water degreasing, cold water rinse I & cold water rinse II, iron phosphating, cold water rinse, passivation & dry off oven treatment. Final finish consists of epoxy polyester powder coating of approved color & shade with a Dry Film Thickness of 50 to 60 (+\- 5) microns. The material is then oven baked with a controlled temperature of 180 deg.C to 200 deg.C. Shelf-It is made of 0.8 thk CRCA steel conforming to IS: 513 Grade or DD. Shelves are having 10 bends & its max load bearing capacity is 70- 80 Kg uniformly distributed per shelf for drive Type of Configuration.. Shelves are mounted on support brackets & shelf level can be adjusted .There are 4 adjustable shelves per body giving 5 loading levels, if no Cradle pair is provided. Shelf Depth for (mm)457- Shelf Depth428mm Box Files (Box file size is 275 mm Wide x 345 mm High x 90 mm Thick) can be accommodated in both 381mm and 457mm deep units.Under framing carrier: The Under framing carrier is a welded frame made of HR sheet 3mm thk.suitably fabricated to take the loads based on configuration Sizes of under framing carrier - Single face fix / Last - 915 x (no. of bays) (Width) X 457 / 381 (Depth) X100 (Height) Finish: The undercarriage, after pre-treatment, is coated with final finish consisting of epoxy polyester powder coat of approved color & shade with a Dry Film Thickness of minimum 50 to 60 microns. Movements of the System: The movement of units is achieved mechanically through a PU Drive wheel and 'Sprocket-Chain-Tensioner' arrangement mounted rigidly onto body side. The torque from hand wheel is transfer to drive shaft via sprocket chain arrangement. 3 BAY- each movable under framing carrier is provided with 3 rollers on the shaft for driving, 3 anti-friction ball bearings for rolling and 4 anti-friction ball bearings for guiding between rails.Fittings:- A Centralized locking arrangement is provided through Locking Stiffener mounted onto back of Single Last unit so that it gets locked on channels when all the units are brought together. The Recess handle lock is placed at suitable height. This arrangement occupies a space of 90.0 mm. Each Drive type units have Locking Knob near the Drive wheel for manual locking of individual units when a person is using those units. Knob shall be rotated to unlock position when units are to be moved. After the unit is moved, before entering into aisle for accessing, this knob shall be rotated to lock position. End stoppers are provided at the end of channels to prevent derailment. Fasteners:- The nuts & bolts are galvanized / blackodized / Zn Plated. Rails / Guide Channels: It consists of 'J' section 2 mm thk HR sheet & 25 mm Square bright bar - both connected by screws. Prior to the embedding of the guide channels with the help of rawl plug & screw, the ground has to be in properly leveled condition.

AURA HIGH BACK CHAIR (LEATHERITE) High Back Dimensions:- Overall height -1230 mm, width - 660 mm Seat Height - 540 mm Back Height - 690 mm Seat Width - 485 mm Head rest should be provided for high back. Head rest should be height adjustable. Back rest should be made up of HR foam on 12 mm ply with fabric upholstery covered with fabric. Back rest shoud have inbuilt lumbar support. Back rest to be tested with 45 Kg, 120000 cycles @ 10-30 cycles / min Seat should be made of HR Foam fitted on 12 mm ply with fabric upholstery and plastic cover and should have waterfall edge for ergonomic seating. Seat Depth adjustment should be provided. Seatrest should be tested with 55 kg on seat, 120000 cycles @ 10-30 cycles / min Mechanism - Mechanism should be synchrony with 1:3 ratio. It should have Automatic weight sensing mechanism with seat slide. The return force of the backrest is adjusted automatically by the users body weight. It should have 4 point locking positions for backrest. It should be BIFMA Compliant and tested with 109 kg on seat for 3,00,000 Cycles. Armrest - Armrest should be adjustable. 3D armrest with PU pad on top. It should be BIFMA compliant. Armrest should be tested with 41 kg on each arm, 60000 cycles Gaslift - Gaslift should have minimum 100 mm stroke length and should be BIFMA Compliant and tested with 122kg on seat, for 60,000 cycles rotation @ 5-10 rotation / min. Base - Base should be Aluminium die cast base and should be BIFMA compliant and tested for 1450 kg of load. Castors- Castors should be twin wheel castors having 60 mm dia. It should be BIFMA Compliant and tested with 102 kg on seat for 1,00,000 Cycles. LEATHERITE -ABRASION RESISTANCE in excess of 80,000 cycles, 600 to 650 GSM Foam - HR Foam and (*** FEW Supporting Specs as per our offering***). Chair should be ANSI / BIFMA X5.1 Certified Supplier should be a BIFMA Member since past 7 years continuously.

GLIDE MID BACK CHAIR Glide – Specification Backrest : Mid back Upholstery : Backrest : Mesh (Black) Seat : Fabric (Black, Grey, Red, Blue) Armrest : Fixed Arm Mechanism : Centre Tilt Mechanism (Seat to back Angle fixed) Gaslift : Class 4, 112mm Stroke Base : Nylon Dia 660mm Castor : Nylon, Dia 60mm Lumber : Yes

Door Providing and fixing in position, Single shuttered aluminium extruded Door powder coated openable door of overall size 0.90 m x 2.40 m with aluminium door frame of powder coated section 101.60 x 44.75mm , 3.18 mm thick and shutter comprising of powder coated section having bottom and lock rail of size 150 mm x 44.5 mm x 3.00 mm thick top rails 47.62 x 44.45 mm x 3.00 mm thick , vertical style 47.62 x 44.45 mm, 3.00 mm thick and for shutter plain glass panes 5 mm thick for top panels and 12mm thick both side laminated phenol bonded particle board panels for bottom panels etc. , I.S.I. mark , heavy duty, Hydraulic floor spring of 150Kilogramcapacity , having heavy duty concealed lock, necessary beading, glazing clips, PVC gaskets, 250mm length tower bolts, 150mm diam. pad handle, etc. as per detailed design and drawing or as directed by engineer in charge including all materials , labours, and equipment etc.Complete.

Wood mat VISITOR CHAIR WITH ARM REST The seat and back shall be made up of wood veneer with foam back. The chair can also be provided with fixed wooden armrests .The dimensions of back shall be 49 cm (W) X 37 cm (H) and of seat shall be 51 cm (W) X 50.0cm (D). The Seat and Back Inner shall be upholstered with PU foam and fabric and shall be assembled over the seat and back. The chair is made of Rubber wood veneer with thickness of the leg 25 mm and width of the leg at 28mm. Seat Height - 46 cm, Height-83.0cm, Width & Depth of Chair as measured from base - Width-60.0cm and Depth-56.0 cm.Dime

SLIDE60 FRAME @ 1200HT - FOR CUBICLE PARTITION Supply, Fitting & Fixing of SOS Make SL 60 Modular workstation. Frame: -The frame shall be made of extruded aluminum sections having 60mm width and average wall thickness 1.6mm. The frame shall be powder coated with epoxy polyester powder with the average thickness 50 to 60 microns conforming to IS 13871: 1993.The frame shall be joined together by Aluminum connectors and all visible aluminum shall be powder coated. Main Frame shall be of 60mm thickness offering various functional and decorative finishes as well as cable management capacity. Height of frame available: 1200mm. Width of frame available: 1050mm, 1200mm. Joints/ posts/ connectors/trims: - The Two frame shall be joined together in 90 degree by using post connector shall be made of CRCA sheet confirming to IS513:2008. Connectors shall be fitted to A-Pole with the help of M6 x 16 pan-head machine screw and washer. The Corners shall be concealed by posts Covers, which shall be a half round Aluminum profiles made up of aluminum extrusion confirming IS733:1983. Tiles- The tiles shall be made to fit the shape of the module and frame, These tiles shall be supported from top and bottom sides with the Tile holder. Tile holder used to incorporate the tile at specified location shall be made of 1.2m Aluminum extrusion confirming the IS 733:1983 with specified powder coating finish up 50 to 60 micron. Tiles are made up of by following material. PRELAMINATED TILES : Laminate tiles shall be made up of 9mm thick prelam one side laminated particle board confirming to IS2046: 1995 in color as specified and 1mm groove is made on both the edge of the tile. FABRIC (PLAIN) TILES: Fabric Plain tile shall be made of fabric wrapped 9mm thick particle board confirming to IS12823:1990 and back side of tile shall be sealed with fevicol PINUP FABRIC TILE: Fabric Pinup (Tackable) tile shall be made with 5.5mm thick PP sheet with 2.5mm thick MDF sheet with fabric wrapped on tile and back side of the tile shall be sealed with fevicol LAM MARKER TILE: Marker tile shall be made with 8mm laminated particle board confirming to IS12823:1990 with 1mm post lamination over it(Marker)

MODULAR FALSE CEILING OF 600X600 SQUARE MINERAL FIBRE BOARD. Providing and fixing Modular false ceiling of 600 x 600 mm center to center and 13 mm thick square mineral fiber board to be fixed on frame work of alluminium sections for suspended false ceiling consisting of alluminium T 2”x1 ½” (50 mm x 40 mm) weighing 0.39 Kilogram/m at 60 cms center center and fixed with ½” x ½” (15 x 15 mm) flanges weighing 0.19 Kilogram/m suspended on 6 mm dia mild steel rod weighing 0.22 Kilogram/m, fixed on wall and beams including rounding of the edges with alluinium T of 2” x 1 ½” (50 mm x 40 mm) weighing 0.39 Kilogram/m etc. (all alluminium sections shall be anodized) including all labour, material, lifts etc. complete.