Public Works Department Tender

Excavation for roadway in earth soil of all sorts, sand, gravel or soft murum including dressing section to the required grade camber and side slopes and conveying the excavated materials with all lifts upto a lead of 50 metre and spreading for embankment or stacking as directed.

Excavation for roadway in hard murum and boulder including dressing section to the required grade, camber and side slopes and conveying the excavated materials with all lifts upto a lead of 50 metre and spreading for embankment or stacking as directed.

Providing earth work in embankment with approved materials obtained from other sources upto lead of 50 metre including all lifts, laying in layers of 20 centimetre to 30 centimetre thickness breaking clods, dressing to the required lines, curves, grades and section, watering and compaction with vibratory roller with V-Sat attachment to achieve not less than 97% of standard proctor density etc. complete (Material obtained from Other sources).

Watering and compacting of embankment formed of materials obtained from the road cutting, within a lead of 50 metre, not less than 97 percent of standard proctor density after laying them in layers of 20 centimetre to 30 centimetre with vibratory roller.

Picking the Black Top road surface including sectioning complete.

Dismantling of flexible pavements and disposal of dismantled materials up to a lead of 1000 metre, stacking serviceable and unserviceable materials separately etc. complete.

Construction of granular sub-base by Plant Mix Method by providing close graded Material, mixing in a mechanical mix plant at Optimum Moisture Content, carriage of mixed Material to work site,spreading in uniform layers with Motor Grader/ Paver on prepared surface and compacting with vibratory power roller to achieve the desired density complete as per clause 401. For Grading II Material.

Wet Mix Macadam (Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density.Laying By Grader/Paver.

Soil Stabilisation of in-situ (existing pavement crust) or soil or otherwise sub-base course upto the required depth by cold in-situ recycling using chemical additives/ otherwise: Providing pulverizing,spreading,milling and mixing of chemical additives at the rate of minimum 750 ml/cum require quantity as per job mix design in accordance with IRC37-2012.Cementitious additive @ rate of minimum 4% should be spread on the existing pavement using a mobile truck mounted containerized cement/additive spreader with microprocessor controlled weighing and spreading system.The additive spreader shall have variable working width sufficient to cover whole pavement lane.The in-situ stabilization process shall be carried out by a mobile and self propelled stabilizer / reclaimer of working width of 2.4 mt and with minimum engine horse power of 440 kw with a variable working depth of minimum 50 cm.The resultant stabilised mix then would be profiled to the required grade ,level and thickness using motor grader and the mix would be compacted using 20 tonne pad foot roller in combination with smooth whell roller to achieve desired proctor density as per IRC37-2012 and complete in all respects and curing with water as required including all materials ,labor and machinery etc. The entire In-situ process would be carried out in single pass with milling and pulverzing of damaged asphalt pavement/soil/aggregates/soil-aggregate mixture to the desired depth and with simultaneous addition of additives and water with machine integrated spray bars fitted on the wheeled self-propelled and vibratory pad foot roller to achieve desired proctor density in all respects. Necessary graded stone aggregates shall be added to achieve desired profile of the road. The minimum unconfined compresssive strength (UCS) of stabilized sub base should be 4.5 to 7 MPa after 7 / 28 days curing as per IRC37-2012 .Also durability aspects (wet-dry cycles) of stabilized sub base should be satisfied as per IRC37-2012.The gradation mixes and magterials should be as per IRC37-2012.

Providing and laying surface dressing as wearing course in single coat using crushed stone aggregates of 10 milimetre nominal chippling size on a layer of bituminous binder laid on prepared surface and rolling with 8-10 tonne smooth wheeled steel roller with Bitumen VG-30 bulk bitumen 9.00 kilogram per 10 Square Metre.

Providing and laying surface dressing as wearing course in single coat using crushed stone aggregates of 6 milimetre nominal chippling size on a layer of bituminous binder laid on prepared surface and rolling with 8-10 tonne smooth wheeled steel roller with Bitumen VG-30 bulk bitumen 7.50 kilogram per 10 Square Metre.

Providing and applying primer coat with bitumen emulsion on prepared surface of Granular Base including clearing of road surface and spraying primer at the rate of 0.60 kilogram/Square Metre using mechanical means.

Providing and applying tack coat on the prepared surface heating by flames in boiler and spraying bitumen with sprayer on dry/hungry Black Top surface at 3.00 kilogram per 10 Square Metre using VG-30 grade bulk bitumen.

Proving and laying Dense Bituminous Macadam using crushed aggregates of grading 1, premixed with bituminous binder VG-30 bitumen at the rate 4.50 percent by weight of total mix and filler, transported to site with Vehicle Tracking System, laid over a previously prepared surface, finished to the required grade, level, alignment and rolling to achieve the desired density for 76-100 milimetrem compacted thickness, using Batch mix type hot mix plant with SCADA, Sensor Paver, Vibratory Roller with Stone Dust filler.

Providing and laying bituminous concrete using crushed aggregates of Grading-1, premixed with bituminous binder at 5.20 percent by weight of total mix and filler, transported to site with Vehicle Tracking System, laid over a previously prepared surface, finished to the required grade, level, alignment and rolling to achieve the desired compaction for 50 milimetre compacted thickness with VG-30 Bitumen, excluding prime/tack coat. Using Batch mix type hot mix plant with SCADA, Sensor Paver, Vibratory Roller with Stone Dust filler. With Waste Plastic at rate of 8 percent by weigt of Bitumen

Supplying hard murum at the road site including conveying and stacking complete.

Spreading the hard murum for side width complete.

Compacting the hard murum side widths including laying in layers on each side with power roller including artificial watering complete.

Construction of dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate (Natural Sand/ VSI grade finely washed Crushed Sand) conforming to IS: 383, the size of coarse aggregate not exceeding 25 milimetre, cement content not to be less than 150 kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant/ Weigh batch mixer, transported to site with all leads and lifts, laid with a paver with electronic sensor/ by suitable means as approved by Engineer-in-charge, compacting with vibratory roller, finishing and curing including preparation of sub-grade surface if required etc. complete.

Providing and laying in-situ M-40 Grade unreinforced plain cement concrete pavement over a prepared sub base with 43 grade cement, coarse and fine aggregate (VSI grade finely washed Crushed Sand) conforming to IS 383, using fine and coarse aggregates combined gradation as per Table 600-3 of MORTH Specification 2013, mixed in a batching and mixing plant/ non tilting mixer and Weigh batcher as per approved mix design, admixtures, transporting to site, spreading, laying with approved make paver,compacted and finished in a continuous operation, finishing to lines and grades as directed by Engineer-in-charge and curing by curing compound/ by providing cement vata in cement Mortar 1:8 of 0.6 metre x 0.6 metre centre to centre, admeasuring 80 milimetre at bottom and 40 milimetre at top with depth of 75 milimetre and maintaining the same throughout curing period/ by any other method approved by Engineer-in-charge.

Providing and laying 125 micron Low Density Polyethylene (LDPE) sheet confirming to IS 3395:1997 below concrete pavement including all materials and labour complete.

Providing and fixing in position TMT FE-500,32 milimetre diameter dowel bars precoated with anticorrosive epoxy paint 60 centimetre long and at 30.00 centimetre center to center wherever directed including handling, straightening, necessary cutting supported by HYSD chairs with proper alignment by using properly designed assembly of Bulkheads lubricating half length with bituminous paint as directed etc. complete.

Providing and fixing in position TMT FE-500, tie bars precoated with anticorrosive epoxy paint of 12 milimetre diameter 70 centimetre long and at 30.00 centimetre center to center and wherever directed including handling, straightening wrapping with paper of approved quality for half length, necessary cutting, handling, straightening, supported by assembly of HYSD chairs with proper alignment etc. complete.

Cutting transverse contraction joints 3 to 4 milimetre wide and depth 60 milimetre in concrete slab using concrete cutting machine with diamond studded saw within 48 hours of casting of bay /slab etc. complete including subsequent widening of the groove 8 to 10 milimetre wide at top having depth of 15 milimetre as directed by Engineer incharge.

Providing to contraction joints polysuphide sealent (Pouring grade) confirming to BS:5212-1989 into sawed groove widened at top for sealent reservoir of specified size and shape as per detailed drawing including fixing Polyethylene foam backer rod of required diameter (approximately 25% larger than the initial 3 milimetre to 4 milimetre joint) overlaid with bond breaking tape as per detailed drawing. Item includes cleaning the joints with water jet/ air compressor and allowing joint to become thoroughly dry before sealent is applied and applying primer. (A) Contraction & longitudinal joints (15 milimetre deep x 8 milimetre wide)

Providing and fixing factory made Hydraulically pressed Mechanically vibrated and compacted precast inter locking cement concrete paving blocks 100 milimetre thick in M-40 grade of approved size and shape for city streets, small /medium market roads,low volume roads, utility cuts on arterial roads etc. as specified and as per IS 15658:2006 including cost of all materials, manufacturing, curing, transportation of blocks to work site including loading, unloading and stacking as directed, laying paving blocks in position over prepared bed of natural sand /crushed sand of 50 milimetre thickness including necessary excavation in all stratas, spreading blindge of fine sand over the prepared bed, compacting blocks by plate vibrator etc. complete.

Excavation for foundation in earth, soils of all types, sand, gravel, soft murum including shoring and strutting, dewatering as necessary and disposing off excavated stuff as directed etc. complete by Mechanical Means.

Excavation for foundation in hard murum including shoring and strutting, dewatering as necessary and disposing off excavated stuff as directed etc. complete.

Excavation for foundation in hard murum and boulders including shoring and strutting, dewatering as necessary and disposing off excavated stuff as directed etc. complete.

Excavation for foundation in soft rock including shoring and strutting, dewatering as necessary and disposing off excavated stuff as directed etc. complete.

Excavation for foundation in hard rock by chiselling and wedging or line drilling including shoring and strutting, dewatering as necessary and disposing off excavated stuff as directed etc. complete. (excluding dewatering).

Providing and laying in situ / ready mix / ready mix M-15 cement concrete of trap metal in foundation including necessary centering, formwork, bailing out water, compacting,curing etc. complete, with fully automatic micro processor based Programmable Logic Controller with Superwisery Control and Data Acquisition enabled reversible Drum Type mixer, with V.S.I. Sand.

Providing and laying plain in situ/ ready mix Mix-25 cement concrete of trap/ granite/ quartzite/ gneiss/ crushed stone metal mechanically mixed, placed in foundation and compacted by vibration including necessary bailing out water, curing curing concrete batch mix plant/ pan mixer with fine agreegates of required specifications (VSI sand finely washed etc.), (excluding dewatering by pump) for 14 days reinforced cement concrete Grade, with concrete mixer.

Providing and laying in situ/ ready mix Mix-25 plain cement concrete of trap/ granite/ quartzite/ gneiss metal for cast in citu piers, abutment, returns, wings etc. including provision of "V" shaped false joints to form suitable panels on the faces to approve design with compacting by vibrating and curing complete, including plywood/ steel formwork centering, (excluding dewatering by means of pump) and including bailling out water and curing finishing in cement mortar 1:3 etc. complete, as directed by engineer in charge, for height upto 5 metre, with Concrete Mixer, with with fine agreegates of required specifications (VSI sand finely washed etc.) The basic rate shall be increased for height above 5.00 metre in following manners (A) Depth upto 10 metre percent extra for rate, (B) Depth upto 15 metre Add 40 percent extra for rate, C) Depth upto 20 metre Add 60 percent extra for rate, (D) Depth upto 20 metre Add 100 percent extra for rate.

Providing and laying in situ/ ready mix controlled Mix-25 cement concrete of of trap/ granite/ quartzite/ gniess metal for reinforced cement concrete caps over piers and abutments including necessary sacffolding plywood/steel formwork, compacting by vibrating, finishing in cement mortar 1:3 and curing etc complete (Excluding reinforcement), with reversible drum type mixer/ concrete batch mix plant (pan mixer), with with fine agreegates of required specifications (VSI sand finely washed etc.)

Providing and laying in situ/ ready mix Mix-30 controlled cement concrete of trap/ granite/ quartzite/ gneiss metal for Reinforced Cement Concrete work in solid/ deck slab etc. including ramming, vibrating, curing, formwork, centering and finishing in cement plaster excluding reinforcement etc. complete, with fully automatic micro processor based Programmable Logic Controller with Superwisery Control and Data Acquisition enabled concrete batch mix plant/ pan mixer and fine agreegates of required specifications (VSI sand finely washed etc.) i) Height up to 5 m, normal rate.ii) Depth 5 to 10 m, add 30 percent extra iii) Depth 10 to 15 m, add 40 percent extra iv) Depth 15 to 20 m, add 60 percent extra v) Depth 20 m and above, add 100 percent extra.

Providing and filling annular space arround footing in rock by using concrete of Mix-15 grade etc. complete.

Providing, cutting, bending, hooking, tying and laying in position Thermo Mechanically Treated FE 500 steel bars for reinforcement for all Reinforced Cement Concrete works as per detailed drawings etc. complete.

Providing and laying of Filter media with granular materials/stone crushed aggregates satisfying the requirements laid down in clause 2504.2.2. of MoRTH specifications to a thickness of not less than 600 milimetre with smaller size towards the soil and bigger size towards the wall and provided over the entire surface behind abutment, wing wall and return wall to the full height compacted to a firm condition complete as per drawing and technical specifications.

Back filling behind abutment, wing wall and return wall by Granular Material as per drawings and technical specifications etc. complete.

Providing and laying 0.90 meter thick metal mat consisting of rubble, oversize metal and normal size metal in specified thickness as per detailed drawing including supplying all materials, hand packing of rubble, spreading metal in layers and hard murum including watering and compaction with power roller etc. complete.

Providing expansion joints with 25 milimetre thick bituminous pad as per detailed drawings etc. complete.

Providing and laying Weep Holes of 100 milimetre diameter Asbestos Cement / PolyVenylChloride pipes as per drawing for abutment returns, return walls etc. complete.

Providing and laying in situ/ ready mix, Mix-30 Reinforced Cement Concrete of trap metal for Reinforced Cement Concrete work of ballast walls and kerbs including scaffolding, compaction, formwork finishing and curing etc. complete, excluding reinforcement, with fully automatic micro processor based Programmable Logic Controller with Superwisery Control and Data Acquisition enabled concrete batch mix plant/ pan mixer and fine agreegates of required specifications (VSI sand finely washed etc.)

Providing tar paper bearing including laying in proper position etc. complete.

Dewatering on Brake Horse Power basis by using water pump including diversion of stream, providing cofferdams, earthern bunds etc. as may be necessary for foundation and other parts of the the works and pumping out water during and after excavation as may be required by using 5.0 to 9.0 Brake Horse Power pump etc. complete. (prior approval of Superintending Engineer will be necessary)

Providing 100 milimetre diameter Galvanised Iron water spouts as per detailed drawings in Reinforced Cement Concrete slab and wearing surface/ kerb etc. complete.

Providing and laying Cement concrete wearing coat M-30 grade with batch mix type/ concrete mixer with SCADA including reinforcement as per drawings and technical specifications etc. complete with fine aggregates of required specifications (VSI sand finely washed etc.)

Providing railing of mild steel angle post 2.0 metre center to center of section 75 milimetre x 75 milimetre x 10 milimetre or equivalent 'I' or 'C' section of height 1.05 above bridge surface with minimum anchor length of 30 cm including hold fast of 25 milimetre diameter mild steel bar welded at the bottom and concreting of 1:3:6 of size 30 cm x 30 cm x 30 cm with three rows of 40 milimetre B class Galvanised Iron pipe provided at 30 centimetre on center to center including scaffolding and one coat of anticorrosive paint with two coats of oil painting, curing of concrete etc. complete.

Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 metre beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting, dewatering etc. complete. by Mechanical Means..

Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 centimetre to 20 centimetre thick including hand packing and compacting etc. complete.

Providing and laying in situ / ready mix cement concrete of Mix-10 proportion with trap/ granite/ quartzite/ gneiss metal in foundation including necessary form work, compacting and curing etc. complete. (with reversible drum type mixer with SCADA. With crushed sand.

Providing cast in situ / ready mix Mix-20 grade cement concrete for head walls of Cross Drainage work / retaining walls etc. including necessary form work, compaction, finishing and curing etc. complete. (with reversible drum type mixer/ concrete batch mix plant (pan mixer) with Superwisery Control and Data Acquisition, with Vertical Shaft Impact (VSI) standard Artificial Sand.

Providing and laying in situ / ready mix Mix-20 cement concrete of trap /granite /quartzite /gneiss metal for approach slab including compacting, finishing, curing etc. complete. (excluding reinforcement) (with reversible drum type mixer/ concrete batch mix plant (pan mixer) with Superwisery Control and Data Acquisition, with fine agreegates of required specifications (VSI sand finely washed etc ), cement

Providing and laying cement concrete pipe of Indian Standard 458:2003 non pressure-4 class of 1200 milimetre diameter in proper line, level and slope including providing and fixing collars in cement mortar 1:2 complete.

Providing and laying cement concrete pipe of Indian Standard 458:2003 non pressure-3 class of 600 milimetre diameter in proper line, level and slope including providing and fixing collars in cement mortar 1:2 complete.

Providing and laying cement concrete pipe of Indian Standard 458:2003 non pressure-2 class of 450 milimetre diameter in proper line, level and slope including providing and fixing collars in cement mortar 1:2 complete.

Providing and constructing Brick Masonry Inspection Chamber 90 centimetre x 45 centimetre and 90 centimetre including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round Glazed Stone Ware pipes, Brick Masonry, plastering from inside and air tight cast iron lid 75 kilogram with frame fixed in cement concrete complete.

Providing and fixing board displaying information, such as 'Name of work, Tender cost, Name of Contractor, Work completion and liability period etc.', having rectangular shape of 1.20 metre x 0.90 metre size made out 18 gauge (1.25 mm.) thick mild steel sheet painted with one coat of Zinc chromate stoving primer and two coats of enamel paint on front side and grey stove enamel on back side and border/ messages/ symbols etc. with approved colour shade paint complete, on Mild Steel angle of size 35 milimetre x 35 milimetre x 3 milimetre frame with properly cross braced Mild Steel angles of size 35 milimetre x 35 milimetre x 3 milimetre duly painted including Two Mild Steel angle iron posts of size 65 milimetre x 65 milimetre x 6 milimetre, 3.65 metre long painted with alternate black and white bands of 25 centimetre width including all fixtures etc. and fixing the boards in 1:4:8 concrete block of size 60 centimetre x 60 centimetre x 75 centimetre including, excavation, refilling, transportation and labour etc. complete.

Providing and fixing Road Junction/ Information sign boards of size 1.80 x 1.20 meter prepared on 16 guage Mild Steel sheet on frame of size 40 x 40 x 5 milimetre with cross bracing of size 35 x 35 x 5 milimetre including painting with one coat of zinc cromate stoving primer and two coats each of green/ white back ground and back side gray stove enamelled, bonded with red retro reflective sheet Engineering grade, border/ letters/ numeral/arrows, coated with non pealable crystal clear protective transperent coat retaining percent reflection includingtwo angle iron post of size 65 x 65 x 6 milimetre of 3.65 metre long inflated at bottom drilled on top and painted in whiteand black bands of 30 centimetre with 4 numbers high strength galvanised iron bolts and nuts of size 10 milimetre diameter and 20 milimetre long sheet and angle iron post in one piece without joints including all taxes, conveying, fixing in ground with cement concrete 1:4:8 block of 60 centimetre x 60 centimetre x 75 centimetre size as directed by Engineer-in- charge etc. complete.

Providing and fixing Road Junction / Information sign board of size 0.90 m x 0.60 metre prepared on 16 gauge Mild Steel sheet with angle iron frame of size 35x35x5 milimetre including painting with one coat of zinc cromate stoving primer and two coats each of green/ white back ground and back side gray stove enamelled, bonded with red retro reflective sheet Engineering grade, border/ letters/ numeral/ arrows, coated with non pealable crystal clear protective coat retaining percent reflection including two angle iron post of size 50x50x5 milimetre of 3.65 metre long inflated at bottom drilled on top and painted in white and black bands of 30 centimetre with 4 numbers high strength galvanised iron bolts and nuts of size 10 milimetre diameter and 20 milimetre long sheet and angle iron post in one piece without joints including all taxes, conveying, fixing in ground with cement concrete 1:4:8 block of 60 centimetre x 60 centimetre x 75 centimetre size as directed by Engineer-in-charge etc. complete.

Providing and fixing Mandatory/Regulatory sign boards in cIndian Road Congressular shape of 600 milimetre diameter made out of 1.5 milimetre aluminum sheet bonded with white retro reflective sheeting of Class B ( Type IV High intensity micro-prismatic grade sheeting-HIP) having pressure sensitive/heat activated adhesive retoreflective specified back ground, border and back side retoreflctive symbols, letters, numerals, arrow as per Indian Road Congress:67-2012 Table No 8.3 Supported with back support frame 25 milimetre x 25 milimetre x 3 milimetre, duly painted on back side with grey stove enamel paint and supported on one numberof mild steel angle iron post of size 65 milimetre x 65 milimetre x 6 milimetre, 3.45 metrelong, duly painted with with flat oil paint having alternate black and white bands of 25 centimetre width including Galvanised Iron fixtures etc. fixing the boards in Mix-25 grade concrete block of size 60 centimetre x 60 centimetre x 75 centimetre including transportation etc. complete. Class B ( Type IV High intensity micro-prismatic grade sheeting-HIP) shall have 7 years written warranty from the manufacturer and authorised distributor/convertor issued for field performance including the screen printed areas and cut-out sheeting and cut-out durable transparent overlay film and this warranty certificate in original should be submitted to the Engineer in charge by the contractor/supplier.

Providing and fixing Cautionary/Warning sign boards in Equilateral Triangle size of 900 milimetre made out of 2 milimetre aluminum sheet bonded with white retro reflective sheeting of Class C ( Type XI Micro prismatic grade sheeting) having pressure sensitive/heat activated adhesive retoreflective specified back ground, border and back side retoreflctive symbols, letters, numerals, arrow as per Indian Road Congress:67-2012 Table No 8.3 Supported with back support frame 25 milimetre x 25 milimetre x 3 milimetre, duly painted on back side with grey stove enamel paint and supported on one numberof mild steel angle iron post of size 65 milimetre x 65 milimetre x 6 milimetre, 3.45 metrelong, duly painted with with flat oil paint having alternate black and white bands of 25 centimetre width including Galvanised Iron fixtures etc. fixing the boards in Mix-25 grade concrete block of size 60 centimetre x 60 centimetre x 75 centimetre including transportation etc. complete. ClassC ( Type XI Micro prismatic grade sheeting) shall have 10 years written warranty from the manufacturer and authorised distributor/convertor issued for field performance including the screen printed areas and cut-out sheeting and cut-out durable transparent overlay film and this warranty certificate in original should be submitted to the Engineer in charge by the contractor/supplier.

Providing and fixing reinforced cement concrete 1:2:4 ordinary kilometre stones including painting,numbering as per Indian Road Congress design for major district road kilometre stone and fixing in standard size cement concrete 1:4:8 block complete.

Providing and fixing reinforced cement concrete 200 metre stone as per Indian Road Congress standard including fixing in block of cement concrete 1:4:8,painting lettering complete.

Providing and erecting a Type-A, W "Metal beam crash barrier comprising of 3 milimetre thick corrugated sheet metal beam rail, 70 centimetre above road/ ground level, fixed on Indian Standard Medium Channel series channel vertical post, 150 x 75 x 5 milimetre spaced 2 metre centre to centre, 1.8 metre high, 1.1 metre below ground/ road level, all steel parts and fitments to be galvanised by hot dip process, all fittings to conform to IS:1367 and IS:1364, metal beam rail to be fixed on the vertical post with a spacer of channel section 150 x 75 x 5 milimetre, 330 milimetre long complete as per clause 810)".

Providing and laying of hot applied thermoplastic compound 2.50 milimetre thick including reflectorizing glass beads at 250 grams per square metre area, thickness of 2.50 milimetre is exclusive of surface applied glass beads as per Indian Road Congress:35. The finished surface to be level, uniform and free from streaks and holes complete.