North Western Railway Tender

Laying of Pre-lubricated HDPE duct, 40 mm OD, 33 ID as per RDSO specification No. 8 RDSO/SPN/TC/45/2013 Rev. 2.0 or latest. The item also includes installation of all the accessories of HDPE duct like end caps, collars, bends, couplers etc. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution.

Blowing/drawing of OFC cables in the HDPE duct along with all the protective work as per instructions of engineer incharge at site. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution.

Fixing & wiring (Laying) of DLP trunk 80X50mm with required all changeable 12 internal/external angle, changeable flat angle, flat junction. Clips, joint for cover, end cap etc. make Legrand or superior. Cable will be supplied by Railway and all other fixing material will be supplied by contractor. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after execution.

Supply. Installation and commissioning of CEL-1 Card consist 04 port 10/100 Mbps Ethernet port for TJ1400 model with associated accessories Warranty 01 year Inspection: Consignee Inspection charges: None Payment terms: 80% after Supply and 20% after execution

Excavation of cable trench as per cable route plan, 1.2 Mtr. deep and of 0.3 Mtr. to 0.6 Mtr. wide at bottom as per RDSO sketch No. SDO/CABLE LAYING/003 or latest alongside the track in normal (all type) soil/strata, conforming to distances as per cable route plan and refilling. This work includes clearing of route from bushes etc, covering of cable laid in trench by loose soil for a layer of 3 50mm thickness approximately before covering by bricks. The work shall be done as per the extant practice on North Western Railway and instructions of Railway Engineer at site. In case 1.2m depth of trench is not achievable due to site conditions, specific approval of JA grade officer will be required for each site where trench depth of 1.2m is not possible. Without the approval of JA Grade officer, no payment for trenching will be made for trench depth less than 1.2m. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution( Unit is Cubic Meter)

Supply, installation, testing& commissioning of Wi-Fi smart mesh Router D-Link EXO 37 DIR2600/Juniper/HP/Cisco or other reputed make with similar or better specs. Make Model Should be Trusted Telecom Portal listed (If applicable) Inspection: Consignee Inspection Charges: None Payment Terms: 100 % after supply

Supply of GNSS based cable route tracer kit with receiver with built in mount for GNSS receiver 12 watt or higher power transmitter with >= 130V voltage boost, suitable for detecting and mapping underground cables with Current direction up/down arrows. Supply shall include locating receiver with RTK receiver powered by locator receiver, transmitter compatible dual Bluetooth android 35 phone, mobile application pre installed i android device with 5 years subscription and PC database software access for direct map generation and download including depth data, 5 Years subscription attached , Make/Model: Rycom pathfinder PLDL route locator with Trimble DA2 GNSS receiver or similar. Detailed specification as attached . The material should be supplied from OEM/ Authorized dealer. Authorization letter should be submitted to Consignee at the time of supply. Inspection: RITES Inspection Charges: Borne by Railways Payment Terms: 100 % after supply

Fixing & wiring (Laying) of DLP trunk 32X20mm with required all changeable 14 internal/external angle, changeable flat angle, flat junction. Clips, joint for cover, end cap etc. make Legrand or superior. Cable will be supplied by Railway and all other fixing material will be supplied by contractor. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after execution.

Supply of Single Mode Single Fiber Optical Media Driver 20KM 10/100/1000(Giga) RJ-45 with inbuilt power supply 230VAC/-48VDC model Techroutes TD-FMC-20KM or superior. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Supply.

Supply , installation, testing and commissioning of 9 U rack with 2 cable manager, 1 PDU with 5 Sockets, 20 screw nuts, 1No. Fan with 500 MM depth of Make :HCL/VALRACK/PRESIDENT Inspection: Consignee Inspection charges: NonePayment terms: 100% after Supply

Supply of Handheld Digital Earth Clamp Tester for clamp on earth/ground resistance 5 measurement up to 1000 ohms. Accuracy 0.1 - 0.99 : 1%, 1 - 49 : 1.5% Also measure current leakage up to 20A. No spines required for measurement Model - DECT-2 or equivalent / higher version make Motwane/Stanlay/Fluke/Megger. Inspection: Consignee Inspection Charges:None Payment Terms: 100% after Supply.

Supply of Network Ethernet LAN cable tester Tool set kit RJ45 Crystal/8p8cand crimping crimper RJ45 for CAT cable. Inspection: Consignee Inspection charges: None Payment terms: 100% after Supply

Supply 1.25 GBPS Single Mode 20 KM 1310nm transceiver dual fiber SFP module Make - eoptical/ cambium/ juniper/ cisco Compatible with item taken in NS 23. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after supply

Supply of IP based LAN extender with 4 ethernet ports speed support up to 5mbps .biz 22 work able up to 5km make CPC/ RAD/ANDA Telecom/team engineers or any other reputed make with similar or better SPECIIFICATIONS with 1 year OEM replacement warranty. Inspection: Consignee Inspection Charges: None. Payment Terms:100% after supply

Supply, installation and complete wiring of optical fibre cable termination box for 6 19 fibres complete with base housing, base mountings with fixing arrangement etc. & splicing of fibre with low loss of pigtail cables. Splice losses in no case should be more than 0.1 dB. Necessary 0dB connectors should be provided in OFC termination box. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after execution.

Horizontal Drilling by using manual pushing method at minimum depth of 1.5 meter 2 below the formation level of earth as per decision of Engineer in charge .Pipe Supply is not covered under this item Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution

Horizontal direction drilling/boring without damage of surface road /track using Auger Machine(HDD machine). The bore shall be upto 200 mm dia & shall be done at the depth of minimum 1200 mm from the ground level. The ground level shall be considered ignoring the bank height of the 1 bank of the road. The length of the bore shall be minimum 4 Mtrs long. This include insertion of different dia DWC-HDPE pipe/ GI pipes coupling etc. as per direction of Engineer In charge. Note:- Pipe Supply is not covered under this item. Contactor shall provide all material required for boring and adequate nos. of labours for proper laying of cables into the bore. Cable shall be laid cautiously so that it should not get damage due to rough handling & pressure on cable. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution.

Supply of single mode Patch Cords LC-SC/LC-LC connectors 5mtrs of reputed make. Inspection: Consignee Inspection charges: None Payment terms: 100% after Supply

Supply of Fault diagnostic and service terminal: Intel Core i5All in One PC with Windows 11 Home as per Technical Specifications attached in Subject tender. Preferred Make Brand: HP, DEL Inspection: Consignee Inspection charges: None Payment terms: 100% after Supply

Supply of UTP CAT-6 cable in a roll of 305 meter and make Siemen/ Systemax / Panduit/ Tyco/ Krone/ AMP. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Supply.

25 mm PVC conduit pipewith minimum 2 mmThickness AS PERIS:9537(PART-3) 32 ORLATESTWITH ISImaking, each of length3 meters. The material should be supplied from OEM/ Authorized dealer only Inspection: Consignee Inspection Charges: None. Payment Terms: 100 % after supply

Fixing of frame, surface box and white cover plates for Two modules. This also includes fixing of RJ-11 Telephone sockets with level holder Jack type, RJ-45 LAN sockets Jack Type (Tool less) and blanking plates for one modules. Make: Legrand or superior. Inspection: Consignee Inspection 16 Charges: None. Payment Terms: 100% after execution.

Supply of frame, surface box and white cover plates for Two modules. This also 15 includes supply of RJ-11 Telephone sockets with level holder Jack type, RJ-45 LAN sockets Jack Type (Tool less) and blanking plates for one modules. Make: Legrand or superior. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Supply.

Supply & Installation of Professional 19" Equipment Racks 4U for housing of network equipments. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after execution.

Supply of FTTH Drop Box along with 1Pcs SC/UPC Adaptor and 1.5Mtr 0.9 MM SC/UPC Pigtail Make - AB-COM, Syrotech or better Inspection: Consignee Inspection Charges: None Payment Terms: 100 % after supply

Supply of single mode SC/APC - SC/APC connector Patch Cords (1 Mtr) of reputed make. Inspection: Consignee Inspection charges: None Payment terms: 100% after Supply

Supply, installation and Commissioning of 4 port GPON OLT Loaded with 9BDM PON SFP with 2 Nos. 10 GBPS SFP along with 3 Years warranty per PON port 2.5 GBPS throughput. With 3 44 year warranty. Warranty certificate to be submitted with supply of material, to consignee. Make Model Trusted Telecom Portal Listed Make - Syrotech Model - SY-GPON-4OLT . or similar in other reputed make Inspection: RITES Inspection Charges: Borne by Railways Payment Terms: 80 % after supply and 20% after commissioning

Supply of OFC jointing kit (6 fiber) with all accessories and splicing of fiber Inspection: Consignee Inspection Charges: None Payment Terms: 80 % after supply and 20% after execution

Supply and installation of 1x16 wall/poll mount FDB box loaded with cassette type 1x2 splitter SC/UPC Make - Syrotech / Tejas or better Inspection: Consignee Inspection Charges: None Payment Terms: 80 % after supply and 20% after installation

Supply of Cable Fault Locater as per Specification attached Preferred Make. Model 36 Stanlay SIDEKICK PLUS 1155-5001 or similar. Advance cable maintenance Test set. The material should be supplied from OEM/ Authorized dealer. Authorization letter should be submitted to Consignee at the time of supply. Inspection: RITES Inspection Charges: Borne by Railways Payment Terms: 100 % after supply

Supply of 1 KVA UPS On line with in built Battery (7Ah/12volt) The capacity of the online ups : 1000 VA ( 1 KVA ) INPUT VOLTAGE: 230 VAC WAVEFORM: SINEWAVE Transfer time: 4-8 ms 27 Battery type & no. : 12V / 7.2Ah*2 pcs. SMF VRLA The efficiency of the online ups : 94%, Rated out Put :-Single phase Sine wave 230 volt Ac/50Hz Volt , Preferred make- APC/Microtek/Luminious Preferred Model Luminous ONLINE UPS 1 Kva LB1000UNO PRO or Similar in Preferred Makes mentioned with Warranty UPS-24 Months, Battery-12 Months. Inspection: Consignee Inspection charges: None Payment terms: 100% after Supply

Supply of Layer 2 8 Port 1G base T with 2x1G SFP uplink with following specification : Zero-touch deployments , Policy Based Automation , Auto device profiling and segmentation, Non- blocking, line-rate architecture with fully featured L2 switching Switch Throughput 20 GBPS with 1 USB 43 port , 1 serial consol port, 19" rack mountable, flash storage 128 MB, DRAM 512 MB VLAN 4K, static route supported switch must be cloud enable. With 3 year warranty. Warranty certificate to be submitted with supply of material, to consignee. Make and model must be listed on Trusted telecom portal approved list. preferred make - cambium network, cisco, juniper. Inspection: RITES Inspection Charges: Borne by Railways Payment Terms: 100 % after supply

Supply of DLP trunk 80X50mm with required all changeable internal/external angle, changeable flat angle, flat junction. Clips, joint for cover, end cap etc. make Legrand or superior. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Supply.

Supply of UTP CAT6 2 Mtr Patch Cord RoHS Complaint make Molex/Systemax/Avaya/D- Link or other reputed make. Inspection: Consignee Inspection charges: None Payment terms: 100% after Supply

Supply of 2 Core unarmored cable O/D 5.8mm OFC cable single mode Make - AB-COM, Molex, Belden Inspection: Consignee Inspection Charges: None Payment Terms: 100 % after supply

Supply of DLP trunk 32X20mm with required all changeable internal/external angle, changeable flat angle, flat junction. Clips, joint for cover, end cap etc. make Legrand or superior. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Supply.

Supply of E1 to ethernet convertor (1E1) E1 to multiple PDH link convertor, E1 port, 4 ethernet UTP ports make - Techroute/ANDA/Zyxel or any other reputed make with similar or better specs. Inspection: Consignee Inspection Charges: None. Payment Terms:100% after supply

Supply of single mode Patch Cords LC-SC/LC-LC connector 3 mtrs (3M/TE connectivity/R&M or other reputed make ) Inspection: Consignee Inspection charges: None Payment terms: 100% after Supply

Supply of Pre-lubricated HDPE duct, 40 mm OD, 33 ID as per RDSO specification No. RDSO/SPN/TC/45/2013 Rev. 2.0 or latest. The item also includes supply of all the accessories of HDPE 7 duct like end caps, collars, bends, couplers etc. Inspection: (i) RDSO/RITES if value of item in work more than 5 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 5 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

Supply of armoured 6 core SM fiber cable suitable for indoor and outdoor; Make Finolex/Molex/ D-link or other reputed make Inspection: Consignee Inspection Charges: None. Payment Terms:100% after supply

Supply of power cable 3 core 2.5 sq mm multi strand (36/0.3 mm dia) cable as per IS 18 694:1990 reaffirmed 1995 or latest suitable for railway electrification area shall be of reputed make like Delton, LAPP, Finolex, or superior. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after supply.

Supply and installation of OFC Joint closure conforming toTEC Spec. and splicing of Optic Fibre Cable' (48 Fibres) andtesting of fibre for 1310 :1550nm. Inspection: Consignee Inspection Charges: None Payment Terms: 80 % after supply and 20% after execution

Supply and installation of 1x16 wall/poll mount FDB box loaded with cassette type 1x4 splitter SC/UPC Make - Syrotech / Tejas or better Inspection: Consignee Inspection Charges: None Payment Terms: 80 % after supply and 20% after installation

Supply, installation, testing & commissioning of 12 port FMS/LIU of 12 fiber (6x2 fiber ) 24 with connector & connecting/splicing the OFC (Pigtails and other miscellaneous material required for the work shall be supplied by the contractor). Inspection: Consignee Inspection charges: None Payment terms: 80% after Supply and 20% after commissioning.

Supply and installation of 1x16 wall/poll mount FDB box loaded with cassette type 1x8 splitter SC/UPC Make - Syrotech / Tejas or better Inspection: Consignee Inspection Charges: None Payment Terms: 80 % after supply and 20% after installation

Supply and commissioning of broadband access device (ONT) with following specification: Dual Band Wi-Fi Speed up to 3000Mbps, 4 LAN ports, one is 2.5G, and the others are 1G, USB 3.0, Compliant with international standards like IEEE802.3ah and ITU-T G.984, OAM/OMCI 45 protocol support for easy configuration and management, Layer 2/Layer 3 functions for carrier-grade FTTH applications, Features EEE802.11b/g/n/ac/ax WiFi 6 for advanced wireless connectivity, Supports XPON dual-mode (EPON/GPON) technology. With 3 year warranty. Warranty certificate to be submitted with supply of material, to consignee. Make Model Trusted Telecom Portal Listed Make - Syrotech Model - SY-GPON-4010-AX3000 or similar in other reputed make Inspection: RITES Inspection Charges: Borne by Railways Payment Terms: 80 % after supply and 20% after commissioning

Laying of S&T Cables of various cores/ pairs/ quads in trenches/ GI pipes/ RCC pipes/ DWC pipes/ Trunking. This also includes laying of cables in track crossings & road crossings. Item 4 includes provision of labels of coloured plastic adhesive tapes or any other identifiable material on each cable to give the cable number at each Gantry Post/hectometer post.(Cables will be meggered before and after its laying by contractor under supervision of Railway Representative and he will submit the meggering report of each testing). Length of the cable laid includes the length of the cable coiled for termination purposes. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution(unit is RM running meter)

Supply of UNI-T 3.5 digit Backlit LCD Mini Digital Clamp Meter Handheld RMS AC/DC Resistance Capacitance Tester Brand: UNI-T UT210E or Similar or superior Inspection: Consignee Inspection Charges: None Payment Terms: 100 % after supply

Supply of Dual band GSM Fixed Wireless FCT Phone with 4G VOLTE support, Make: 55 BEETEL F3-4G GSM Fixed Wireless Phone or similar or superior specification in Panasonic or other reputed make. with Built-in Battery Back-up. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after supply

Supply and Installation of Indoor Access Point Supply, configuration, and installation of 2:2X2 Wi-Fi indoor access point per the specifications :- (1) access point should be a dual-band, dual- radio indoor access point. The minimum data rate supported shall be 1200 Mbps in 5 GHz and 570 Mbps in 2.4 GHz.. , (2) access point should have at least a 3 dBi antenna gain for 5GHz and 3 dBi for 2.4GHz radio. (3) access point must have MU-MIMO antennas. (4) access point should have at least a 3 dBi antenna gain for 5GHz and 3 dBi for 2.4GHz radio. (5) access point should support a minimum of 1.7 Gbps aggregate data rates. (6) access point should support the latest amendments of IEEE 802.11 a/b/g/n/ac/ax. (7) access point should provide at least 18 dBm transmit power on both radios. (8) access point should support at least 16 SSIDs. (9) access point should have at least one 100/1000 Mbps RJ-45-based Ethernet PoE port. (10) access point should be flexible hardware that can be deployed standalone, and controller based. (11) access point should support IPv4, IPv6, IEEE 802.1Q, band balancing, airtime fairness, QoS, and ACL features. (12) access point should be able to act as 53 WIDs/WIPS. (13) access point should provide zero service interruption and handle client traffic if the controller goes down. (14) access point should support auth/encryption methods for wireless, i.e., Open, WEP, WPA2-AES, WPA3-SAE, IEEE 802.1X/EAP, and AAA. , access point should follow Wi-Fi alliance standards WMM, 802.11d, 802.11h, and 802.11e. , access point should support role-based access control, rate-limiting, device fingerprinting, 802.11w MFP, and 802.11r fast roaming. , access point should support management frame protection. , access point should support management frame protection., (15) access point should have administration access through a secure graphic user interface. , Apart from controller-based configuration, the proposed access point should provide standalone operation without changing AP hardware. If the controller configuration disallows GUI/CLI access, it should follow the same. (16) access point should have an operating temperature of 0-40 °C. access point should have been approved by the Wireless Planning Commission (TRAI, Govt of India). ETA certificate or Wi-Fi alliance certificate is also mandatory. With 3 year warranty. Warranty certificate to be submitted with supply of material, to consignee. Make Model must be listed on Trusted Telecom Portal. Inspection: RITES Inspection Charges: Borne by Railways Payment Terms: 80 % after supply and 20% after commissioning

Supply of Layer 2 24 Port 1G base T with 4x1G SFP uplink with following specification : Zero-touch deployments , Policy Based Automation , Auto device profiling and segmentation, Non- blocking, line-rate architecture with fully featured L2 switching Switch Throughput 56 GBPS with 1 USB 40 port , 1 serial consol port, 19" rack mountable, flash storage 128 MB, DRAM 512 MB VLAN 4K, static route supported switch must be cloud enable. With 3 year warranty. Warranty certificate to be submitted with supply of material, to consignee. Make and model must be listed on Trusted telecom portal approved list. Preferred make - cambium network, cisco, juniper. Inspection: RITES Inspection Charges: Borne by Railways Payment Terms: 100 % after supply

Installation of Layer 2 switch 24 port mentioned in NS 23 Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after installation