Municipal Corporation Tender

Item No.4 Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 cm to 20 cm thick including hand packing and compacting etc. complete.

Item No.5 Providing and laying Ready Mixcement concrete in M20 of trap/ granite/quartzite/gneiss metal for steps including steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface, only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Item No.6 Providing and laying Ready Mix cement concrete M-30 of trap /granite /quartzite /gneiss metal for R.C.C.work in foundations like raft, strip foundations, grillage and footings of R.C.C.columns and steelstanchions etc. columns as per detailed designs and drawing or as directed including Steel centering formwork, coverblocks laying / pumping,compaction finishing the formedsurfaces with cement mortar1:3 of sufficient minimum thickness to give as mooth and evensurface or roughening if special finish is to be provided and curing etc. complete .(Excluding reinforcement and structural steel). with fully automatic microprocess or based PLC with SCADA enabled reversible Drum Type mixer /concrete Batchmixplant (Panmixer) etc.complete. Withfine aggregate (Natural Sand /Crushed sand VSI Grade finely washed etc)

Item No.7 Filling in plinth and floors with contractors material/brought from outside and approved by Engineer incharge in layers of 15 cm to 20 cm including watering and compaction etc. complete.

Item No.8 Providing and laying Ready Mix cement concrete M-30 of trap / granite /quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks compacting and roughening if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc)

Item No.9 Providing and laying Ready Mix cement concrete in M-30 of trap/ granite/ quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finelywashed etc)

Item No.10 Providing and laying Cast in situ/Ready Mix cement concrete in M-30 of trap/ granite/ quartzite/ gneiss metal for R.C.C. pardi of required thickness including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade

Item No.11 Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. Complete

Item No.12 Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15mm thick in cement mortar1:4 using water proofing compound at 1kg per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the snd faced treatment 6 to 8mm thick in cement mortar1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete.

Item No.13 Providing and applying antipeel paint of approved make & approved brand exterior Emulsion paint of approved quality, colour and shade to old and new surface in two coats, including exterior acrylic primer coat, scaffolding, preparing the surface etc. complete (Heat Reflective Paint).

Item No.14 Providing and laying Ready Mix cement concrete M-15 of trap/ granite/quartzite/gneiss metal for coping to plinth or parapet, moulded or chamfered as per drawing or as directed including steel centering, plywood/ steel formwork compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laidconcrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.) With fine aggregate (Crushed sand VSI Grade)

Item No.15 Waterproofing Treatment to plastered surface of toilet & bathroom walls minimum up to 90 cm (Dado) by using 2-(methoxycarbonyl)-1-propene-Butyl-2 propenoate (MPBP) based polymeric waterproofing solution as approved by Engineer in charge. Clean the entire surface thoroughly and over this prepared surface, apply three coats of 2- (methoxycarbonyl)-1-propene-Butyl-2 propenoate (MPBP) based polymeric waterproofing solution as approved by Engineer in charge.While the 3 coat is wet broadcast sand on the surface. Provide 20 mm thick cement plaster in CM 1:3 with one pouch of 330 grams of thorough blend of special cements, aldehyde based polymers, shrinkage compensating agents as approved by Engineer in charge per 50 Kg bag of cement including all lead, lifts ,curing etc complete. Acrylic Polymeric Waterproofing Coating for Concrete and Masonry should have following minimum properties: 1. Elongation % (ASTM D412-2016): @ 100% 2. Tensile Strength N/mm2 (ASTM D412-2016): 3.3 3. Specific Gravity: 1.02 ± 0.02 4. Total Solids (ASTM D1644-2012): 43.98 5. Hardness Shore A (ASTM D2240-2015): 82 It shall be applied as per manufacturer’s specification.

Item No.16 Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete.

Item No.17 Providing and fixing corrugated galvanised iron sheets of 0.63mm thick (24 B.W.G.) for roofing without wind tiles including fastening with galvanised iron screws and bolts, lead and bitumen washers as per drawing etc. complete.(Weight of 5.5 Kilogram/sq.m.)

Item No.18 Providing, fabricating and erecting at site of work the tubular steel structure (shed) as per standard design and specifications having various spans in between trusses and in multiples of standard length of bays as specified as per standard specifications, inclusive of cost of steel tubular trusses, tubular columns purlins, tie runners, foundation bolts, base plates, nuts and bolts, welding wherever required etc. as per detailed drawing inclusive of one coat of anticorrosive paint and two coats of oil painting of approved quality and shade etc. complete. Spec. Number : As directed by Engineer-in-charge.

Item No.19 Providing and fixing valley gutter of 22 B.W.G. (0.8 mm) plain galvanised iron sheets 90 cm wide with teak wood planking 20 mm thick including two coats of coal-tarring the upper surface of plank etc. complete. (excluding painting to underside of plank).

Item No.20 Providing and fixing plain zinc sheeting of 0.80 mm thick (22 B.W.G.) over the ridge hip or valley to galvanized iron sheet roofing including all fastening and bolt galvanised iron screws and bolts, lead and bitumen washers etc. complete.(Weight of 6.8 Kilogram/sq.m.).

Item No.21 Providing and fixing P.V.C. Rain water pipes of 110mm outer diameter and having wall thickness of 2.2 to 2.7 mm confirming to I.S. 13592-1992 including proper rainwater receiving recess with P.V.C. plug, bend, necessary fittings, such as, offsets, shoes, inluding fixing the pipe on wall using approved wooden cleats projecting 25mm to 40mm from face of wall a fixing with clips of approved quality and number ,filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on C.C. or masonry blocks, including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations of pipes. All the P.V.C. fittings and additional 2 piece socket clips shall be got approved from engineer in charge etc. complete.

Item No.22 Providing & Fixing 0.60m X 0.50m clear internal size of M.S. Galvanised hinged type grating and frame (weighing minimum 71 kg) with minimum 75 microns zinc coating by hot dipped galvanising the MS grating and frame as per IS 2629. (The contractor shall furnish the certificate of galvanising from the Galvaniser.) incuding testing ,inspection of material sample and finished product in presence of M.C.G.M. Engineers (3 nos.) at Manufacturers works, as per Standard Specification no SP-SWD-3 and as per drawing (Dwg No. MCGM/SWD/2013-03), etc complete as specified & as directed by Engineer in Charge.

PART - A.2 - COMPOUND WALL Item No.1 Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 3.00 m.) By Manual Means

Item No.2 Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 3.00 m.) By Manual Means

Item No.3 Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 cm to 20 cm thick including hand packing and compacting etc. complete.

Item No.4 Providing and laying Ready Mixcement concrete in M20 of trap/ granite/quartzite/gneiss metal for steps including steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface, only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Item No.5 Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete.

Item No.6 Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, racking out joints, watering and scaffolding Complete. Spec. No.: Bd.G.5 Page No. 315

Item No.7 Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15mm thick in cement mortar1:4 using water proofing compound at 1kg per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the snd faced treatment 6 to 8mm thick in cement mortar1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete.

Item No.8 Providing and fixing 50 mm. dia. medium class G.I.pipe gate with wicket gate of approved drawing with all fixtures and fittings in two leaves with strong hold fast embedded in c.c. block at top and bottom with locking arrangement including cutting, bending, making holes and with one coat of primer etc. complete.

Item No.9 Providing and fixing mild steel grill gate as per the detailed drawing including hinges, locking arrangements and painting in three coats of oil paint of approved colour and shade etc. complete.(weight 18 Kilogram. to 20 Kilogram. Per Sq.m.) Spec.Number: As directed by Engineer- in-charge

Item No.10 Providing and laying Ready Mix cement concrete in M-30 of trap/ granite/ quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finelywashed etc)

Item No.11 Providing and laying Ready Mix cement concrete M-30 of trap / granite/quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. columns as per detailed designs and drawing or as directed including Steel centering formwork, cover blocks laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Item No.12 Providing and laying Ready Mix cement concrete M-30 of trap / granite /quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks compacting and roughening if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc)

Item No.13 Providing and applying antipeel paint of approved make & approved brand exterior Emulsion paint of approved quality, colour and shade to old and new surface in two coats, including exterior acrylic primer coat, scaffolding, preparing the surface etc. complete (Heat Reflective Paint).

Item No.14 Providing and fixing corrugated galvanised iron sheets of 0.63mm thick (24 B.W.G.) for roofing without wind tiles including fastening with galvanised iron screws and bolts, lead and bitumen washers as per drawing etc. complete.(Weight of 5.5 Kilogram/sq.m.)

Item No.15 Providing and fabricating structural steel work in rolled sections like joists, channels, angles, tees etc. as per detailed design and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted / bolted /welded connections without connecting plates, braces etc. and including one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade etc. complete.

Item No.16 Providing expansion joints in R.C.C. framed structure (at terrace level) with premoulded filler 25 mm thick and 3 mm thick aluminium plate as required, bituminous poured filler, fixing lead, flashing on upper side and T.W. battens on inner face finishing etc. Complete as directed.

PART - A.3 - C-C PAVEMENT Item No.1 Excavation for roadway in earth, soil of all sorts, sand, gravel or soft murum including dressing section to the required grade, camber and side slopes and conveying the excavated materials with all lifts upto a lead of 50m. and spreading for embankment or stacking as directed.

Item No.2 Excavation for roadway in hard murum and boulder including dressing section to the required grade, camber and side slopes and conveying the excavated materials with all lifts upto a lead of 50m.and spreading for embankment or stacking as directed.

Item No.3 Excavation for roadway in soft rock, including dressing section to the required grade, camber and side slopes and conveying the excavated materials with all lifts upto a lead of 50m. and spreading or stacking as directed.

Item No.4 Excavation for roadway in hard rock by wedging and chiselling or line drilling including dressing section to the required grade, camber and side slopes and conveying the excavated materials with all lifts upto a lead of 50m. and spreading for embankment or stacking as directed

Item No.5 Providing earth work in embankment with approved materials obtained from other sources upto lead of 50m. including all lifts,laying in layers of 20cm. to 30cm. thickness breaking clods, dressing tothe required lines, curves, grades & section, watering and compaction with vibratory roller with V-Sat attachment to achieve not less than 97 % of standard proctor density etc. complete ( Material obtained from Other sources)

Item No.6 Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader / Paver on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401 -- By Mix in Place Method and Grading - I Material

Item No.7 Construction of dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate ( natural sand/ VSI grade finely washed crushed sand) conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm, , cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant/ Weigh batch mixer, transported to site with all leads and lifts, laid with a paver with electronic sensor /by suitable means as approved by Engineer-in-charge , compacting with vibratory roller, finishing, curing and including preparation of subgrade surface if required etc. complete.

Item No.8 Providing and laying in-situ M40 Grade unreinforced plain cement concrete pavement over a prepared sub base with 43 grade cement , coarse and fine aggregate ( natural sand/ VSI grade finely washed crushed sand) conforming to IS 383, using fine and coarse aggregates combined gradation as per Table 600-3 of MORTH Specification 2013, mixed in a Tilting type Concrete Mixer as per approved mix design, admixtures, spreading, laying compacting and finished in a continuous operation without paver machine, finishing to lines and grades as directed by Engineer-in-charge and curing by curing compound /by providing cement vata in cement Mortar 1:8 @0.6m X 0.6m centre to centre, admeasuring 80 mm at bottom and 40 mm at top with depth of 75mm and maintaining the same throughout curing period by any other method approved by Engineer-in-charge.

Item No.9 Supplying and Fixing of Molded Shank Raised Pavement Markers / Cat's Eye made of polycarbonate and ABS moulded body and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face and shall support a load of 16000 kg tested in accordance to ASTM D 4280 Type H and complying to Specifications of Category A of MORTH Circular No RW/NH/33023/10-97 DO III Dt 11.06. 1997. The height, width and length shall not exceed 50 mm, 100 mm and 102 +/- 2 mm and with minimum reflective area of 13 Sqcm on each side and the slope to the base shall be 35 +/- 5 degree. The strength of detachment of the integrated cylindrical shanks, (of diameter not less than 19 +/- 2 mm and height not less than 30+/- 2 mm) from the body is to be a minimum value of 500 Kg. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer's recommendation and complete as directed by the engineer.The contractor shall submit a two year warranty for satisfactory field performance including stipulated retroreflectance of the reflecting panel, to the Engineer.

Item No.10 Providing and fixing of retro- reflectorised informatory sign board rectangular/Square in shape having area less than 0.9 square meter made out of 2 mm aluminum sheet bonded with white retro reflective sheeting of Class B ( Type IV High intensity micro-prismatic grade sheeting-HIP) having pressure sensitive/heat activated adhesive retoreflective specified back ground, border and back side retoreflctive symbols, letters, numerals, arrow as per IRC:67-2012 Table No 8.3, supported with back support frame 25mm x 25mm x 3mm, duly painted on back side with two coats of grey stove enamel paint and supported on one no. mild steel angle iron post 75 mm x 75 mm x 6 mm, 3.5 mt long firmly fixed to the ground by means of properly designed foundation with M25 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing The angle iron post shall be duly painted with one coat of epoxy primer and two coats of epoxy finish paints having alternate black and white bands of 25 cm width including GI fixures and transportation etc.complete.The nut bolts of board with angle iron post/supporting structure after fixing at site has to be electrically welded. Class B ( Type IV High intensity micro-prismatic grade sheeting-HIP) sheeting shall have 7 years written warranty from the manufacturer and authorised distributor/convertor issued for field performance including the screen printed areas and cut-out sheeting and cut-out durable transparent overlay film and this warranty certificate in original should be submitted to the Engineer in charge by the contractor/supplier.

Item No.11 Providing and laying Ready Mixcement concrete in M20 of trap/ granite/quartzite/gneiss metal for steps including steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface, only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Item No.12 Providing dry / trap/ granite/ quartzite/ gneiss rubble stone soling 15cm to 20cm thick including hand packing and compacting etc. complete.

Item No.13 Providing and fixing heavy duty interlocking concrete Coloured paving blocks of 80 mm thickness of having a strength of 300 Kilogram/Sq.cm. of approved quality and shape on a bed of crushed sand of 25 to 30 mm thick including skirting joints and cleaning etc. complete

Item No.14 Providing and fixing Cautionary/Warning sign boards in Equilateral Triangle size of 600 mm made out of 3mm aluminum sheet bonded with white retro reflective sheeting of Class B ( Type IV High intensity micro-prismatic grade sheeting-HIP) having pressure sensitive/heat activated adhesive retoreflective specified back ground, border and back side retoreflctive symbols, letters, numerals, arrow as per IRC:67-2012 Table No 8.3 Supported with back support frame 25mm x 25mm x 3mm, duly painted on back side with grey stove enamel paint and supported on one no. of M. S. angle iron post of size 65 mm X 65 mm X 6 mm, 3.45 m long, duly painted with with flat oil paint having alternate black and white bands of 25 cm width including G.I. fixtures etc; fixing the boards in M25 grade concrete block of size 60cm X 60cm X 75cm including transportation etc; complete. Class B ( Type IV High intensity micro-prismatic grade sheeting-HIP) shall have 7 years written warranty from the manufacturer and authorised distributor/convertor issued for field performance including the screen printed areas and cut-out sheeting and cut-out durable transparent overlay film and this warranty certificate in original should be submitted to the Engineer in charge by the contractor/supplier.

Item No.15 Providing and fixing in position TMT FE 500, 32 mm dia dowel bars precoated with anticorrosive epoxy paint of required Dia. 60 cms. Long and at 30.00 cm. C/C and wherever directed including handling, straightening, necessary cutting supported by TMT FE 500, chairs with proper alignment by using properly designed assembly of Bulkheads lubricating half length with bituminous paint as directed etc. complete.

Item No.16 Providing and fixing in position TMT FE 500, tie bars precoated with anticorrosive epoxy paint of 12 mm dia. 70 cms.long and at 30.00 cm. C/C and wherever directed including handling, straightening wrapping with paper of approved quality for half length, necessary cutting, handling, straightening , supported by assembly of TMT FE 500, chairs with proper alignment etc. complete.

Item No.17 Cutting transverse contraction joints 3 to 4 mm wide and depth 60mm. .in concrete slab using concrete cutting machine with diamond studded saw within 48 hours of casting of bay / slab etc. complete including subsequent widening of the groove 8 to 10 mm. wide at top having depth of 15 mm. as directed by Engineer incharge.

Item No.18 Providing and laying 125 micron Low Density Polyethylene (LDPE) sheet confirming to IS 3395 : 1997 below concrete pavement including all materials and labour complete.

Item No.19 Disposal of excavated material upto 5 km lead

Item No.20 Road Marking with Hot Applied Thermoplastic Compound with Reflectorizing Glass Beads on Bituminous Surface- Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorizing glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.complete

Item No.21 Providing to contraction joints polysuphide sealent (Pouring grade) confirming to BS:5212-1989 in to sawed groove widened at top for sealent reservoir of specified size and shape as per detailed drawing including fixing Polyethylene foam bacer rod of required diameter (appraox.25% larger than the initial 3mm. to 4mm. joint) over laid with bond breaking tape as per detailed drawing. Item includes cleaning the joints with water jet/ air compressor and allowing joint to become thoroughly dry before sealent is applied and applying primer. (A) Contraction and longitudinal joints (15 mm. deep x 8 mm.wide)

PART - A.4 Electrical work for Waste Trasfer Station at Panvel sector -21 Item No :- 1 Providing & erecting 8 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 135 mm A/F, top 70 mm A/F on provided foundation as per specification no. OH-PL/OPL

Item No :- 2 Providing and erecting galvanised 1000mm Single arm sword type bracket with FRP dome and ball as per specification no. OH-PL/PBKT

Item No.3 :- Providing and erecting galvanised 1000mm Double arm sword type bracket with FRP dome and ball as per specification no. OH-PL/PBKT

Item No.4 :- Supplying and erecting LED street light fitting suitable for above 70W - 75W lamp, including lamp, with PF 0.95 class IP 65 and above housing of pressure die cast aluminium alloy and heat sink extruded aluminium complete as per specification No FGODF/FLS2

Item No.5 : Supplying, erecting & marking SPMCB 6A to 32A, B- series (for lighting) in provided distribution board as per specification no. SW-SWR/MCB

Item No.6 : Making M- 20 grade reinforced cement concrete foundation by considering the safe soil bearing capacity at site as 10 T/sq.m at 1.5 m depth including supply of steel, concrete, excavation and fixing provided nut bolts with the help of template, duly plastered as per design complete (for 6m to 8m high octagonal /conical GI pole) for 8 mtr Street light pole

Item No.7: Supplying and erecting mains with 3x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW ( for street light pole)

Item No.8: Supplying and laying (including excavation of suitable width & depth up to 90 cm) 50 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete.

Item No.9: Supplying & erecting three phase, 415V, street light control panel up to the max load of 6kW, TPN MCB 40A, powder coated CRCA 14 SWG sheet, outdoor type, having IP54,IK10 protection, suitable rating contactor, 24 hrs. astronomical time switch with minimum 5 years battery back up, auto/manual selector switch, ON/OFF push buttons, indicator lamps, control wiring, metering device, etc. for automatic operation, with overcurrent, short circuit, earth fault protection on provided iron frame / CC foundation

Item No.10: Supplying and erecting of two pole Structure including RSJ Poles,foundation, Insulators and AB Switch with dog ACSR conductor etc for electrical connection from MSEDCL side complete

Item No.11: RMU iii) Supplying, installing, testing and commissioning SF 6 Insulated 22kV, 630A, 16kA/3sec, 3 way outdoor, extensible motorised SCADA compatible RMU, internal arc tested as per electric supply company specification consisting of 1no. feeder with 1 LBS and 2 nos. feeder with 2 VCB compliant to IEC 62271 - 100, 200 and 102, as per specification no. SW-HTS/RMU SCADA

Item No.12: HT Cable i)Supplying , erecting & terminating XLPE insulated galvanised steel formed wire armoured (strip) cable 22 kV(E), 3 x 300 sq. mm. aluminium conductor laid in provided trench / pipe as per specification no. CB-HT…2Run + rmu to transformer

Item No.13: ii) Providing and erecting Heat shrinkable out door termination kit for 11 kV (UE)/ 22 kV ( E ) XLPE HT cable 3x up to 300 sq. mm. cable with necessary material as per specification no. CB-JT/HT

Item No.14: iii) Providing and erecting Heat shrinkable indoor termination kit for 11 kV (UE)/ 22 kV ( E ) XLPE HT cable 3x240 to 300 sq. mm. with necessary material as per specification no. CB-JT/HT

Item No.15: iv) Providing and erecting Heat shrinkable straight through joint kit for 11 kV (UE)/22 kV ( E ) XLPE HT cable 3x240 to 300 sq. mm. with necessary material as per specification no. CB-JT/HT

Item No.16: Reinforced cement concrete pipe Supplying & laying (including excavation) reinforced cement concrete pipe of IS 458:2003 NP-2 class of 150 mm internal diameter in proper line, level and slope including providing and fixing collars in cement mortar 1:2 and curing etc. complete

Item No.17: Half round reinforced cement concrete pipe Supplying & laying (including excavation) half round reinforced cement concrete pipe of IS 458:2003 NP-2 class of 150 mm internal diameter in proper line, level and slope including providing and fixing collars in cement mortar 1:2 and curing etc. complete.

Item No.18: Transformer Supplying, installing, testing & commissioning 3 phase, 22/0.433 kV, 50 Hz., 100 kVA, Mineral oil immersed and naturally cooled outdoor type, aluminium wound Non-sealed transformer , delta/star connected with additional neutral brought out on load side, temperature rise should not exceed 40℃ by thermometer in oil and 45℃ by the resistance method in winding at full load rating, using type A winding insulation (kraft paper), with HV tapping (with off load tap changer) off load +2.5 to -5 in steps of 2.5%, having 4 number of tap positions, with standard accessories complete with test certificate with losses below 357 Watts at 50% load, 1197 Watts at 100% load as per IS:1180 (part 1 ) : 2014 with necessary permissions of Electrical Inspector, as per specification no SS- TR-NSL

Item No.19: Transformer Plinth Making transformer plinth (1.5 x 1.5 x 1.5) m in size with necessary excavation in ground with 150 mm. thick M- 10 PCC at the bottom and top and 250 mm. thick, burnt brick wall constructed at periphery and remaining hollow portion shall be filled with 40mm hard broken aggregate. External surface duly plastered by 12 mm thick including watering etc complete.

Item No.20: Transformer Fencing i) Supplying and erecting fencing of section having size 2450 mm in height from ground level and 1200 mm width with angle iron frame work erected in CC foundation and painted complete as per specification no SS-AS/FSG Fencing for Size :4 Mtr x 6 Mtr Area No of Sections : 15 No x 1.2 Mtr + 0.5 Mtr x 1 No

Item No.21: ii) Supplying and erecting 50 x 50 x 6 mm angle iron as corner support 2m long fixed at the middle of the fencing frame and the other side inclined at 30 degree angle, in cement concrete foundation of 15 x 15 x 40 cm complete duly painted with one coat of red oxide and two coats aluminum paint complete

Item No.22: iii)Supplying and erecting double leaf hinged door each 1500 mm in width x 1850 mm in height using B class, GI pipe with angle iron supports, chain link wire mesh (jali) complete supported on channel iron, erected in foundation, and painted complete as per specification no SS-AS/DLD

Item No.23: Providing pipe type earthing with 40mm. dia. G.I. pipe or 20 mm dia. G.I. Rod complete with all materials testing and recording the results as per specification no. EA-EP ( for street light pole+LT & street light Panel +Feeder Piller)

Item No.:24 Supplying and erecting GI earth wire of high purity of different sizes used for earthing or any other purposes on wall with necessary G. I. Clamps fixed on wall/cable/ conduit with screws in an approved manner ( for street light pole)

Item No. 25: Providng earthing with galvanized iron earth plate size 60 x 60 x 0.6 cm complete with all materials, testing & recording the results as per specification no.EA-EP ( Transformer + RMU)

Item No. 26: Supplying and erecting GI strip of high purity required size used for earthing on wall and/or any other purpose with necessary GI clamps fixed on wall painted with bituminous paint with joints required. As per specification no EA-EP.

Item No.27: Supplying, installation and testing of maintenance free earthing comprising of Electrode of 17.2 mm diameter Low Carbon Steel with 250 micron molecular copper bonded earthing rod of Length 3m along with 25 kg Carbon based environment friendly back fill ground enhancing compound required to fill up the excavated earth with required quantity complete, and recording the results Specification no. EA-MOBI

Item No.28: Supplying, erecting & terminating XLPE insulated unarmoured cable 1100 V. 1 core 120 sq. mm. copper conductor complete erected with provided lugs, laid in provided control panel /distribution boards / pipe as per specification no. CBLT/CU Transformer to feeder Piller & LT Panel

Item No.29: Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3.5 core 70 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL ( LT Panel to Transfer unit )

Item No.30: Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 25 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per pecification no. CB-LT/AL for street light pole

Item No.31: Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 4 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL for street light pole

Item No.32: Supplying and erecting triple pole mini feeder pillar with 500V, 200A FPMCCB as incomer and 2 outgoing circuits with HRC fuse base and cartridge of100A with aluminium bus bar erected in 14 SWG CRCA sheet box with supporting angles, self locks, gasket having IP54,IK10 protection and slanting top to be erected on provided foundation complete as per specification no. SWSWR/ MFP as per MSEDCL norms

Item No.33: Supplying and erecting LT CT multifunction DLMS compliance energy meter of accuracy of class 0.5 , 3x240V,50 Hz with optical & RS 232 port, backlit LCD, measure & display trivector energy, load survey, TOD, tamper detection & logging, power ON /OFF events, instantaneous parameters of rating 1/5 A with display in absence of power complete with zero adjustment & test certificate from manufacturer erected on provided M.S. box and connected to CTs.

Item No.34: Supplying and erecting plywood 6 mm thick fixed to wall or on provided panel board with necessary materials such as screws, wall fasteners supports, nuts bolts etc. complete.

Item No.35: Designing, providing , fabricating, erecting commissioning and testing L.T. Panel board cubical type with equipment’s as per detailed specifications Panel Enclouser - Including panel Encloser 1030 Kg 1) I/C -MCCB -200 A 25 KA -1 nos with all accessories , Rotary handle ,Spreader link 2) O/G -MCCB -100 A 25 KA -3 nos with all accessories , Rotary handle ,Spreader link 3) O/G -MCCB -32 A 25 KA -3 nos with all accessories , Rotary handle ,Spreader link 4) O/G -RCBO -63 A 25 KA -6 5) O/G -RCBO -40 A -5 nos including digital Voltmeter & Ammeter with Indication Lamp (RYB)

Item No.36: Supplying and fixing PVC synthetic elastomer electrically insulating mat with class A insulation conforming to IS: 15652 – 2006 having 2 mm thickness up to 3.3 kV

Item No.37:APFC Supplying and erecting 40 kVAr, 440 V 3 phase, 50 Hz., Contactor Logic &Intelligent Relay micro APFC passive filter panel, consisting of suitable steps of APP/MPP type capacitor units with Detuned (harmonic filter) reactors of suitable rating , APFC panel shall be compliance to IEC 61439 and power quality IEC 61921 standard as per specification no CP-ED/APFC

Item No.38: Fixed Type Capacitor Supplying and erecting 525 V 3 phase, 50 Hz., APP type capacitor having minimum overcurrent capacity of 1.8 In, peak inrush current capacity 300 In and minimum life 150000 hours kVAr bank of all polypropylene condensers (APP) with the standard capacities of 2, 3, 5, 7, 10, 12.5 and 15 kVAr units of P.F. correction for operation on 3 phase 50 Hz. with externally discharging resistances, earthing terminals and built on angle iron or channel iron frame work and provided with terminal cover box complete erected on provided iron bracket or on floor duly tested by licensee.

Item No.39: Internal electrification for Waste Transfer Station i) Point wiring for light/fan/bell in 20 mm FRLS grade HMS PVC conduit with 1.5 sq.mm (2+1E) FRLSH grade copper wire with flush type switch and required accessories as per specification No: WG-PW/SW

Item No.40: ii) Point wiring for independent plug in 20 mm FRLS grade HMS PVC conduit with 1.5 sq.mm (2+1E) FRLSH grade copper wire, flush type switch, earthing and required accessories as per specification No: WG-PW/SW

Item No.41: iii) Wiring for plug on board with flush Switch socket, copper wiring and earthing as per specification No:WG-PW/SW

Item No.42: iv) Supplying and erecting integrated LED Highbay Fitting 70W IP65 & IK08 class having die cast aluminium housing with polycarbonate diffuser with integrated optics, having system lumens output of Min.10000 Lumens, min. efficacy of 145 lumen/W, CRI70, CCT upto 6500K, THD10%, p.f. 0.90, operating range of 140-240V, inbuilt surge protection of 4 kV, Life class of 50,000 Hrs. at L50B50 , including driver complete with 3 Year warranty as per specification No FG-ODF/FLS2.

Item No.43: v) Supplying & erecting inverter LED batten 20W tube light fitting with polycarbonate housing, heat sink, integrated HF electronic driver, Min. 2600 mAh Lithium ion Battery with charging time of 8-10 Hours and backup time of Min. 3 hrs. with minimum 25% of initial Watts having luminous efficacy of 100 lumen/watt, CRI80, CCT of 6500K and THD=20% having useful life of minimum 25000 hrs. with overheating protection with 2 years warranty.

Item No.44: vi)Supplying and erecting mains with 3x 4 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Item No.45: vii) Supplying and erecting regular/ standard model ceiling fan of 900 /1050 mm. sweep complete erected in position as per specification no. FG-FN/CF

Item No.46 viii)Supplying and erecting integrated LED street light fitting 60W IP65 & IK08 class having single piece pressure die-cast aluminium housing, having system lumens output of Min. 7700 Lumens, min. efficacy of 110 lumen/W, CRI70, CCT upto 6500K,THD10%, p.f. 0.95, operating range of 140-270V, inbuilt surge protection of 10 kV, Life class of 50,000 Hrs. at L70B50, including driver complete with 3 Years warranty as per specification No FG-ODF/FLS2.

Item No.47: ix)Supplying & erecting FRP box of size 250mm x 200mm x 100 mm, 2.7 mm thick complete on pole/wall as per specification No. CB-SB

Item No.48: x) Supplying and erecting street light Wall bracket made from 25 mm. dia ‘ G.I. pipe 1.2 m. in total length complete as per specification no. FG-BKT/WB

Item No.49: xi)Supplying & erecting triple pole and neutral distribution board (TPNDB), SPMCB of 8 ways / phase (24 poles), with door, 1.2mm thickness surface/ flush mounted, IP 43 Protection on iron/GI frame (horizontal busbar type) as per specification no. SW-SWR/MCBDB( office + security cabin+ ground & first floor +weigh bridge

Item No.50: xii)Supplying, erecting & marking SPMCB 6A to 32A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Item No.51: xiii)Supplying and erecting Gate/garden light fitting with 200mm dia. glass bowl suitable for upto 12W LED Lamp on provided pipe as per specification No. FGODF/GLT

Item No.52:- xiv)Supplying & erecting 10-12W, 230V integral type LED Lamp suitable for B-22 / E-27 base.

Item No.53:- xv)Supplying and erecting mains with 2x4 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

Item No.54:- xvi)Supplying and laying HMS PVC conduit FRLS grade 25 mm dia with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC

Item No.56 :- On Grid Solar System Supplying, installing, testing and commissioning of 25 kWp ON-GRID Solar PV System / Plant consisting Solar PV Poly Crystalline Panel (335 Wp X 75 Nos.) and Solar ON-GRID Inverter of similar capacity (THD3%) with interconnecting wires / cables up to solar ON GRID inverter, proper base plate, canopy box to house Inverter and necessary accessories i.e. ACDB/ DCDB , MCB etc. wiring up to solar Inverter in casing and capping, display board, sign board, two distinct earthing, lightning arrester, liaisoning charges, remote monitoring system with maintaining card / chip for 5 years including net charges for RMS System, complete up to net meter installation and export to the grid with 5 year ON-SITE warranty and fully comprehensive maintenance contract as per Specification no. ESD-RT-ONG.

Item No. 57:- Mounting Structure -Providing structural steel work in single stanchions composed of RSJ, channel, etc. with caps, bases, mild steel plates, angles, brackets, cleats, gusset plates, anchor bolts, etc. as per detailed design and drawing or as directed by Engineerincharge including cutting, fabrication, hoisting, erecting, fixing in position, making riveted / bolted / welded connections and one coat of anticorrosive paint and over it two coats of oil painting, etc. complete. (BdC-6/277)

Item No. 58:- Supplying and installation of Solar PV 1.00 Module cleaning unit consisting of nozzles spray, necessary pipes, valves, post, electronic panel board concealed with weather proof cabinet, spreading water periodically for removal of dust, related motor pump, controller, timer and nozzles set suitable for covering 5 KW Solar PV Module. (Approx. 35 Sq. Mtr. PV Module areal. Rate for 5 KWp Rs =22541 as per note additional Kw capcity add 4000 for every 5 kW so 20 kWP cost is Rs.= 16000+22541= 38541

Item No.59 :- Supplying and erecting AC three phase LT CT multifunction net meter DLMS compliance of accuracy class 0.5, 3 x 240V, 50Hz, with backlit LCD display, optical port & RS 232 port (measures import kWh, kVAh, export kWh, kVAh, Net kWh, kVAh, V, I, kW, 6 months history of energy, load survey, TOD, tamper detection & logging, power ON/OFF events, instantaneous parameters of rating 1/5A with display in absence of power) with wiring connections and mounting hardware on provided panels complete with calibration certificate from manufacturer

Item No.60 :- Centrifugal Pump Supplying & erecting Minimum three & above star rated Centrifugal water pump (Monoblock), 415V, three phase 50 cycles A.C. supply of 1.5 KW/2 HP with discharge 600/140 Litres per Minute (LPM) for head of 8/22 m and 50 mm suction/ 40 mm delivery pipe on provided C.C. foundation as per specification No. WP-CGP for Water

Item No.61 :- DOL Starter Supplying and erecting DOL starter to operate squirrel cage induction motor working on 380- 440 Volt, 3 phase, 50 Hz with no volt coil and over load element with necessary material and connected to supply, etc complete. Starter with original sheet steel encloser

Item No.62 :- Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 2.5 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

PART - A.5 Water Supply Item No :- 1 Providing and laying Ready Mix cement concrete in M20 of trap/ granite/quartzite/gneiss metal for steps including steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface, only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Item No.2 : Providing and fixing H.D.P container one piece moulded water tank made out of low density polythyler and built corrugation including of delivery up to destination hoisting and fixing of accessories such as inlet, outlet overflow of all tanks capacity above 1000 to 20,000 litres

Item No.3 : Providing ISI mark G.I. pipe of following class and dia. excluding GST levied by GOI & GOM in all respect, inspection charges, transportation to stores, etc. complete as per IS-1239/2004. Note: One coupler shall be provided with each full length of pipe cost of which is included in rates below. For Medium Class 25 mm Dia

For Medium Class 40 mm Dia

For Medium Class 80 mm Dia

Item No.4 :- Providing double flange sluice valve confirming for IS- 14846 including worn gear arrangements as per test pressure, stainless steel spindle, caps, including inspection charges, transportation upto departmental store, unloading, stacking excluding GST levied by GOI & GOM in all respect. Sluice valves - PN -1.0 With byepass arrangement 25 mm dia

40 mm dia.

80 mm dia

Item No.5 :- Providing and constructing B.B. masonry valve chamber with 15 cm thick 1:3:6 proportion PCC bedding, excluding excavation, B.B. masonry in C.M. 1:5 Proportion, 20mm thick cement plaster in CM 1:4 proportion on both side, precast RCC frame and cover, etc.complete as directed by Engineer-in-charge. Chamber size 0.9 x 0.9 x 1.2 m

Item No.6 :- Providing, erecting and giving test of submersible pump set conforming to IS 8034 and motor conforming to IS 9283, with water proof winding. Pump shall be suitable for various delivery head and discharge with stainless steel shaft. Motor suitable for working on 415 V ± 10%, 3 Ph, 50 Hz A.C. Supply, with cable guard, thrust carbon/fiber bearing to withstand entire hydraulic thrust. The pump set shall be suitable for direct coupling, with suitable suction strainer. Pump should have suitable discharge out let as per manufacturer's design. Antithrust stream lined non return valve shall be provided with the pump. 3 m submersible copper conductor cable in single / double run and 2 pairs of suitable size erection clamp 10 mm thick shall be provided with each pump.PM 1-1 Submersible Pump set 100 mm dia (with Polypropylene / Noryl Impeller) up to 20 stages PM 1-1-1 1.5 HP

Item No.7 :- Providing and fixing 15mm diameter water meter with non-return valve including strainer,sockets/ union nut and including water meter box making locking arrangement and lock.

Item No.8 :- Providing, laying and fixing P.V.C. pipe of 15mm dia. with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Item No.9 :- Providing and making UPVC/MDPE pipe consumer service connection on Distribution main by drilling hole with suitable means , including all labour , UPVC/MDPE Pipe of required length with or without Road crossing as described below, including cost of specials like Saddle/Clamp Saddle of suitable material, and diameter suitable for Distribution main, 15mm /20mm/ 25mm respective Dia Heavy duty Brass/Polyprophylyne(Twin Jacketed ) Ferrule , Male and Female thread adapter Elbow, Bends,couplers ,Tees, Clamps of suitable material and sundry materials as per requirment, including providing and fixing medium duty 15.mm brass bib tap, GI casing pipe of suitable diameter of 32mm/ 40mm/ 50mm respectively of required length for Road crossing, including requird labour for excavation in all types of strata up to the depth of 0.75m or as per site requirement,all types of plumbing fittings, refilling , Closing the water supply in that area, dewatering, hydraulic testing and restarting the water supply ,transportation of material etc. complete as directed by Engineer In Charge a) 15 mm Dia.

PART - A.6 Drain Item No :- 1 Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 0.00 to 1.50 m.) By Manual Means

Item No. 2 : Excavation for foundation in hard murum and boulders including removing the excavated material up to a distance 50 metres, beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5m.) By Mechanical Means

Item No. 3 : Excavation for foundation in Soft rock and old cement or lime masonry foundations including removing the excavated material upto a distance of 50 metres beyond the building area and stacking as directed, including dewatering, preparing the bed for thefoundation and necessary back filling with available earth /murum, ramming, watering including shoring and strutting etc. complete (lift upto 1.5m) By Mechanical Means

Item No. 4 : Excavation for foundation in Hard rock by chiselling, wedging, line drilling, etc. including trimming and levelling the bed, removing the excavated material upto a distance of 50 metres beyond the building area stacking as directed, dewatering and back filling with available earth/ murum watering, ramming etc. complete. (Lift upto 1.5 m). By Mechanical Means

Item No. 5 : Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 cm to 20 cm thick including hand packing and compacting etc. complete.

Item No. 6 : Providing and laying Ready Mix cement concrete in M20 of trap/ granite/quartzite/gneiss metal for bed blocks, foundation blocks and such other items including bailing out water, Steel centering, formwork, laying/ pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Item No. 7 : Providing and laying Ready Mix cement concrete M-30 of trap / granite /quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. columns as per detailed designs and drawing or as directed including Steel centering formwork, cover blocks laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc)

Item No. 8 : Providing and laying weep holes of 100 mm diameter PVC pipes as per drawing for abutment returns, return walls etc. Complete.

Item No. 9 : Providing and laying Ready Mix cement concrete in M-30 of trap/ granite/ quartzite/ gneiss metal for R.C.C. pardi of required thickness including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc)

Item no 10 : Providing trap/ granite/ quartzite/ gneiss rubble filling over haunches and arches including hand packing. Spec. No.: BR.34 Page No. 146

Item No. 11 : Providing and laying Ready Mix cement concrete M-30 of trap/ granite / quartzite/ gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc)

Item No. 12 : Providing, cutting, bending, hooking, tying and laying in position TMT FE 500 steel bars for reinforcement for all RCC works as per detailed drawings etc. complete.

Item No. 13 : Disposal of excavated material upto 5 km lead

Item No. 14 : Providing and casting in situ or precast tapering R.C.C. M-20 Barrier type Kerb without gutter ( as per IRC 86 1983) embedded 125mm below ground level over M-10 PCC finished neatly with C.M. 1:2, setting the same in C.M. 1:2, including the required excavation in any strata and removing the excavated stuff any where in city and redoing the surface as specified and directed by Engineering In-charge. Using Concrete Batching and Mixing Plant

Item No. 15 : Providing and applying two coats (exterior quality) of flat oil paint of approved colour and shade to the plastered surface including scaffolding if necessary, cleaning the surface and preparing surface etc. complete. (excluding primer coat)

Item No. 16 : Providing , laying and fixing ,jointing Eco- drain 110 mm SN 8 Nu- Drain Upvc pipes or of equivalent make, manufacture as per EN 13476 or equivalent as per I.S.15328 with fittings such a bends, tees, coupler, etc, jointing with rubber lubricant including necessary excavation, trench refilling with selective excavated material etc. complete.

PART - A.7 Office Container Item No :- 1 Providing and supplying Portable Office Cabin with Toilet Clear Height of 8.6 ft with Extra Height of size of 12 x 4 x 8.6 ft and PVC Ceiling , Provided with Internal Wall Cement Board with Paint , Including 1 Nos. of CFL, 1 Nos. of EWC Toilet, 1 Nos. of Exhaust, 1 Nos. of Bulkhead, 1 Nos. of Wash Basin and MCB as per specifications . Clear Height of 9 ft with Extra Height of size of 30 x 10 x 10 ft and PVC Ceiling , Provided with Internal Wall Cement Board with Paint , Including Inbuilt Partition , L Shape Manager Table , Workstation 1 high black revolving Chair and 8 low back revolving chair as per specifications .The item includes all necessary acessories, fixtures and equipments required for installation of entire assembly etc. Complete. And Prior Approvel of Engineering Incharge is necessary. 1. Bottom Frame - 100x50 mm ISMB/ISMC 2. Top Frame - 50mm x 50mm MS Sq. Pipe 3. Stiffener Bottom - 80mm x 40mm MS Sq Pipe or 100x50 mmISMC for OfficeCabins 4. Stiffener Top - 40 x 20 M.S. Sq. Pipe 5. Side Post - 65mm x 65mm MS Sq. Pipe 6. Paneling Outside -1 mm GI Corrugated Sheet (Jindal/AMNS) 7. Internal Wall Paneling - Cement Board with Paint 8. Roof Outside - G.I. 1mm SHEET (make Jindal/essar/ uttam) Properly weldedforStrength up to and water tight with TARFELT Sheet. 9. False Ceiling - PVC Ceiling 10. Bottom Flooring - 18mm Cement Board with Vinyl Carpet 11. Aluminum Windows - Aluminium Powder Coated Windows 12. Door - All Doors will be Insulated with for locking agreement, Holddraft& Handles. 13. Insulation - Proper Glass Wool Insulation 25 mm(16kg/m3) / For Toilet NA 14. Wiring - All wiring shall be concealed type & shall be of PVCinsulatedcopper wire. (Polycab/Finolex) 15. Electrical Fittings - Earthing Point shall be provided for SAFETY 16. Ear thing - Earthing Point shall be provided for SAFETY 17. Outside Painting - Phosphate the Cabin and painting with 1coat of Epoxy primer withTwo Coat of Epoxy Paint. 18. Legs - 6-inch height, Four legs at all four corners 19. Hooks - Specially formed Hooks for Easy lifting and shifting 20. Furniture - NA 10. Bottom Flooring - 18mm Cement Board with Vinyl Carpet 11. Aluminum Windows - Aluminium Powder Coated Windows 12. Door - All Doors will be Insulated with for locking agreement, Holddraft& Handles. 13. Insulation - Proper Glass Wool Insulation 25 mm(16kg/m3) / For Toilet NA 14. Wiring - All wiring shall be concealed type & shall be of PVCinsulatedcopper wire. (Polycab/Finolex) 15. Electrical Fittings - Earthing Point shall be provided for SAFETY 16. Ear thing - Earthing Point shall be provided for SAFETY 17. Outside Painting - Phosphate the Cabin and painting with 1coat of Epoxy primer withTwo Coat of Epoxy Paint. 18. Legs - 6-inch height, Four legs at all four corners 19. Hooks - Specially formed Hooks for Easy lifting and shifting 20. Furniture - NA 15. Electrical Fittings - Earthing Point shall be provided for SAFETY 16. Ear thing - Earthing Point shall be provided for SAFETY 17. Outside Painting - Phosphate the Cabin and painting with 1coat of Epoxy primer withTwo Coat of Epoxy Paint. 18. Legs - 6-inch height, Four legs at all four corners 19. Hooks - Specially formed Hooks for Easy lifting and shifting 20. Furniture - NA 21. Toilet Accessories - Commode & flush tank- Hind ware Remaining Accessories - Local Make Prior approval of Engineer is Necessary

PART - B.1 Transfer Station Equipments Item No :- 1 Providing and Installing Transfer Station Hopper Type should meet the following requirements : 1) Transfer station capacity : 200 MT/day (appx) 2) Expected volume of garbageTipper’s of D2D system : 1 MT (appx) 3) Present tonnage of incoming garbage Appx./day: 100 MT/day (appx) 4) Density of incoming refuse (variable) : 0.4 MT/cu.mt. 5) Operating hours of refuse transfer station : 24 hours (as per PMC) 6) Present peak hour time : 8 a.m. to 12 a.m. & 2.00pm to 6.00 pm 7) compacted garbage density required : 0.7 - 0.8 T/cu.mt. 8) No. Of unloading bays per unit (RTS) at present : 2 Pcs / RTS. Providing and Installing Transfer Station of Hopper Unit has following Three Parts : A. Transfer Station Stationary Compactors The provuder shall design the compaction unit so as to achieve minimum 0.7 to 0.8T/M3 density of compacted garbage. The Refuse transfer station compactor shall be capable of handling garbage having the characteristics as shown in appendix. The compactor will be of rear loading type with a hydraulic bucket to receive waste from primary collection vehicles and unload the waste into the charge chamber of the equipment. The proposed Refuse transfer station compactor shall have cycle time of 45-60 seconds with minimum charge box area of 3 M3 . Container compaction time should not be more than 24-26 min. for 20 CuM containers. The Refuse transfer station static compactor shall be capable of handling minimum 35 Mt/Hr garbage. The compaction unit shall be the proven & established product of the principle manufacturer & shall be tested for relevant characteristics. The test certificates shall be produced prior to supply as well as after the test-run before final commissioning of the units. The successful tenderer shall complete the work of supply, installation, testing and commissioning of the Stationary compactor System with Hopper and required accessories etc. Other Requirements are given below. It should have following specifications : 1) Compaction Chamber Volume : 3m3 2) Compaction cycle time : 40-45sec 3) Theoretical volumetric capacity : 263m3 /h 4) Normal pressure : 26Mpa 5) Max pressure : 30Mpa 6) Normal compaction force : 320kN 7) Max compaction force : 370kN 8) Power : Min.15kW 9) Distance into container : Min 500MM 10) Voltage : 440V 11) Compaction Density : 0.7 -0.8t/m3 12) Compaction chamber floor plate : Min.12mm Hardox or equivalent 13) Ram plate : Min.12mm Hardox or equivalent 14) Rear tipcart lifting capacity : 2500Kg B. CONTAINER - HANDLING UNIT (DOOR LIFTING, PUSH PULL SYSTEM AND CLAW MECHANISM) - The transfer station compaction unit shall have hydraulically operated container handling unit to align the container & refuse transfer station compactor unit in proper position to avoid spillage of waste during compaction.Container handling unit shall have arrangement for lifting the rear side sliding door of the container using its hydraulic system.The container-handling unit shall be the proven & established product of the principle manufacturer & shall be tested for relevant characteristics. The test certificates shall be produced prior to installation as well as after the test-run before final commissioning of the unit. C. HOPPER AND FEEDER ARRANGEMENT - The tenderer shall provide 6mm thk mild steel hoppers at the transfer station having garbage holding capacity as per present one at site. Hopper capacity should be approx..25cum. The hopper opening area at the top shall be designed in such a way that garbage should not come out while unloading the Equipment’s.The hopper shall be well supported by MS structure of appropriate size to take self weight and weight of the garbage. The design and drawing for the structure shall be submitted by the successful tenderer. The hopper and feeder arrangement shall be painted with epoxy / corrosion resistant paint. Color shed will be as per the requirement of PMC.Hopper shall be having 3 side railing system at the top from where garbage will be dumped inside it . All joints of the hopper must be supported with required MS materials and quality of welding shall be good for better life and working.

Item No 2: - Providing and Installing 20CuM MS Container for Garbage transportation should meet the following requirements : The closed top, rear loading type container will be compatible with Hook loader as well as stationary compactor to be installed at transfer station. The container will have rear door opening by ratcheting arrangement for loading refuge at processing site. it shall also have mechanical locking arrangements to lock them with stationary compactor while loading the refuge.20cum container made of IS2062 E350Grade steel with suitable mechanical rachet locking, sliding door, heavy duty container roller and hook loader lifting hook. The Container would be used for storage and transportation of compacted of municipal solid waste. Container should be of 20 CuM volumetric capacities. The lifting hook shall be integrated within the frame and be capable of taking specified load. Container shall have arrangement to collect leachate forming during compaction. Container Shall have upward sliding door (Guillotine) arrangement. It shall be having proper sealing also. It should have following specifications : 1) Container Volume : 20cum 2) Shape : Cylindrical 3) Dimensions (Overall) : 6000(L)X2350(W)X2498(H)Approx 4) Floor Thk : 6MM 5) Side Wall Thk : 4MM 6) Weight : Approx.4200kg 7) Hook Rod Dia : 50mm dia 8) Rachet Lock : Provided 9) Roller : 2nos -Heavy duty roller on Rear sides 10) Reinforcement : Provided 11) Painting : The inside of container to be coated with two coat black color and Bottom of the container shall also be painted with black anti corrosive paint. The outside shall be painted as per customer requirement with minimum one coat of first quality synthetic paint to ensure long lasting structure suitable for handling raw garbage under corrosive conditions. Prior to painting coat of anticorrosive zinc rich primer shall be applied as per the paint manufacturer standard. The supplier should paint number on container and messages on the body color code shall be different for dry waste & wet waste container as per customer requirement.

Item No 3: - Providing and Installing HOOKLOADER WITH T CHASIS should meet the following requirements : The hook loader equipment mounted on a truck chassis (HLE) shall be used for lifting loading the closed containers (General 20 cum vol capacity) and discharging the solid waste.materials like garbage, garden waste and other like refuse materials by lifting the container at the desired location. The hydraulically operated HLE Shall be capable of loading unloading the steel container on/from chassis having by hooking and rolling on/off principle. HLE shall be capable of enough to handle the load of 20 MT with at least 10% safety factor. HLE shall be provided with an arm type hook mechanism for loading and unloading the container. The HLE will have a control frame assembly located with an outer structure to handle and to tip the container. It shall have telescopic jib with heavy duty hook. Two main rams for lifting/tipping standard containers locking arrangement, hydraulic pump, stabilizers and other by hydraulic element as per functional needs. The hydraulic pump will be driven by the vehicle engine gearbox throw the power take off (PTO) unit. A pair of roller assembly located at the rear end of the container will facilitate and guide the main beam sections of container during loading/unloading of the container. Necessary safety locking arrangement (Mechanical) shall be provided to lock the container with the HLE. Tipping operation of the container shall be done after effective locking. All safety control like holding valves, check valves/relief valves, electric hydraulic / Pneumatic functional interlocking arrangements will be provided for operational reliability. It shall have all required hydraulic connections for loading-unloading-locking-emptying of the container. All control levers shall be provided at a convenient location for operation. It should have following specifications : 1) HLE Capacity/Model : T22/L6000 2) Hyd pump capacity : 80LPM 3) Operating Pressure : 310 Bar 4) Hyd Tank Capacity : 100 Liters The hook loader should be mounted on Truck Chassis of 28 T GVW (6X4) of TATA/Ashok Leyland/Eicher or equivalent. The Chassis should be with Non-Sleeper Driver Cabin fitted with PTO and Hydraulic Pump. Other requirements are given below. 1) Chassis GVW : 28Ton 2) Engine HP : Min 200 3) Suspension : NRS 4) Wheelbase : 5000 to 5050mm

Item No 4: - Providing and Installing Fully Electronic 20T – 7.5 x 3 mtr Appro. – Modular Pit less Type Weigh bridge (Capacity – 20T, Accuracy – 2Kg), along with 4 no’s of separate steel structure, 6 nos. of Multiended Shear Beam Digital Load cell, Digital Indicator, Jumbo Display, Junction Box, Printer, Printer Cable, UPS without battery . Weighing bridge at appropriate location to register entry and exit of vehicles. RFID tags on hook loader vehicles. RFID tags on containers, RFID reader at transfer station, Integration with cameras to capture image of vehicle (along with number plate) entering & existing transfer station. System should be able to capture all the following attributes but not limited to at the time of weighing and printing of weighing slip.

Item No 5: - Providing and Installing Container change over system is used to move the containers automatically from the compactor on a changeover system to storage (buffer) more containers (empty or full) at the station. The device can be driven by a hydraulic cylinder. A hook-loader vehicle take the full container onto or load an empty container on the change-over bed, at the same time the compactor can continuous load the container with waste. Power Driver System - The components are constructed from reputed global brands. The system is integrated in the rear of the compactor. Optimized the system by LESS valves,and positioned outside for better serviceability. Crusher cylinder support was relocated to the middle, which significant improve the lifetime of the machine.The Leachate collection chamber should be provided inside the container which functions as sewage storage tank. Sewage collection tray installed on the compactor to collect and guide the sewage to the disposal. Ball valve on the container for drain during the compaction must be provided.

PART - C.1 Leachate Treatment Plant Item No :- 1 Excavation for foundation in earth, soil of all types, sand, gravel and soft murum,including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5 m.) By Mechanical Means

Item No :- 2 Excavation for foundation in Hard murum including removing the excavated material upto a distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift from 1.5 to 3.0m.) By Mechanical Mean

Item No :- 3 Excavation for foundation in Soft rock and old cement or lime masonry foundations including removing the excavated material upto a distance of 50 metres beyond the building area and stacking as directed, including dewatering, preparing the bed for the foundation and necessary back filling with available earth/murum, ramming ,watering including shoring and strutting etc. complete. (Lift 3.00m to 4.5m ) By Mechanical Means

Item No :- 4 Excavation for foundation in Hard rock by chiselling, wedging, line drilling, etc. including trimming and levelling the bed, removing the excavated material upto a distance of 50 metres beyond the building area stacking as directed, dewatering and back filling with available earth/ murum watering, ramming etc. complete. (Lift from 4.50 to 6.00m). By Mechanical Means

Item No :- 5 Excavation for foundation in earth, soils of all types, sand,gravel and soft murum, including removing the excavated material upto a distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift from 1.5m to 3.0m) By Mechanical Means

Item No :- 6 Excavation for foundation in hard murum including removing the excavated material upto distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.50 m) By Mechanical Means

Item No :- 7 Excavation for foundation in hard murum and boulders including removing the excavated material up to a distance 50 metres, beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5m.) By Mechanical Means

Item No 8 :- Excavation for foundation in earth, soil of all types, sand, gravel and soft murum,including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5 m.) By Mechanical Means

Item No. 9 :- Excavation for foundation in earth, soil of all types, sand, gravel and soft murum,including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5 m.) By Mechanical Means

Item No. 10 :- Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 cm to 20 cm thick including hand packing and compacting etc. complete.

Item No. 11 :- Providing and laying Ready Mix cement concrete in M20 of trap / granite / quartzite / gneiss metal for bed blocks, foundation blocks and such other items including bailing out water, Steel centering, formwork, laying/ pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Item No. 12 :- Providing and laying Ready Mix cement concrete M-30 of trap / granite /quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. columns as per detailed designs and drawing or as directed including Steel centering formwork, cover blocks laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Item No.13:- Providing and laying Ready Mix cement concrete M-30 of trap/granite/ quartzite/ gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete, (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Item No.14:- Providing and laying Ready Mix cement concrete in M-30 of trap/ granite/ quartzite/ gneiss metal for R.C.C. pardi of required thickness including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Item No.15:- Providing and fixing in position HCRM / CRS (Corrosion Resistant Steel) bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete.

Item No.16 :- Roads Congress, recommended for use by Ministry of Road Transport & Highways and should have a 4 year track record of use in both the Gulf Region and India. Admixture should have evaluated test reports demonstrating a corrosion rate of zero coulombs after 9 test cycles as per ASTM G 109 when tested from a research institution NBA accredited Grade A and internationally ranked among top 5 research institutions in the world in Annual Survey conducted by Georgia Institute of Technology ranking of research institutions. PH of admixture should be alkaline in nature, specific gravity of 0.99 – 1.1, colour : brownish. The contractor must intimate the engineer in charge prior to addition in concrete for recording. If the admixture is put in the concrete mix at the batching plant, a written record of the amount of admixture used shall be supplied to the engineer. The engineer must ensure that the specified dosage of admixture is added in the concrete mix. (Material Cost Analysis only)

Item No.17 :- Providing and applying epoxy paint of approved make (Shalimar, Ciba or Mahindra & Mahindra) to concrete surface of RCC ESR or GSR or any other structure including cleaning the surface by scrapping and air blowers to the satisfaction of Engineer-in-charge, necessary scaffolding, etc complete with all leads and lifts and giving satisfactory hydraulic test for water tightness, film test as per I.S. codes.

Item No.18 :- Disposal of surplus excavated materials upto specified lead and all lifts including loading, unloading, stacking and spreading as directed by Engineer-in-Charge etc. complete Lead Upto 3.0 Km

Item No.19 :- Dewatering the excavated trenches and pools of water in the building / pipeline trenches, well works by using pumps and other devices including disposing off water to safe distance as directed by Engineer-In-charge (including cost of machinery, labour, fuel), etc. complete.

Item No.20 :- Providing and fixing G.I. pipe railing having 1.0 M height consisting 50 x 50 x 6 mm thick M. S. angles as verticals at 1.5 M c/c, distance and additional posts at every corner bends to curved shape with 3 rows of 25 mm dia G.I. pipes of medium class variety as horizontal and painting 3 coats of oil paint over 1 coat of anticorrosive paint of approved colour and shade including cost of all labour, transporting bends to curved shape,etc. complete.

Item No.21 :- Providing and laying mechanical protective layer over water roofing membrane with cement screed plaster 1:5 after laying chicken mesh over membrane including curing etc. complete 20 mm thick with cost of chicken mesh etc. complete and covering 7 years guarantee on court stamp paper of Rs.100/- including necessary testing specified by Engineer (Prior permission of S.E. is necessary before inclusion of this item in estimate)

Item No.22 :- Providing pre construction antitermite treatment as per I.S. 6313 (Part-II) by treating the bottom surface and sides of excavation at the rate of 5 litres of emulsion concent rate of 1.0 percent of chloro phyrifos per square meter of surface area covering 10 years guarantee on bond paper.

Item No.23 :- Proof Cheacking of deatiled designing of RCC structure and taking third party approval from IIT for all the strucuteres and submitting 6 copies of Design and Drawing to NMMC for record purpose, including third party charges, transporation, site visit and all

Item No.24 :- Providing detailed geological reports of proposed site by maintaining geotechnical investigation of structure stratification collecting soil, rock and ground water samples for laboratory tests to arrive the foundation design parameters . Rock properties such as type of rock, jointing fractures, etc. complete with suggestion about the site foundation and remedies.

Item No.25 :- Providing and fixing reinforced cement concrete cover of size 90 cm x 45 cm with frame over inspection chamber etc. complete. Heavy duty (225 Kilogram)

Item No.26 :- Providing and removing barricading with the help of portable fencing along the running track where the work is to be done in close vicinity of the track. Fencing shall consist of self supporting steel angles of size 50 x50x6mm, 1.5m long provided with hooks etc. and embedded in CC 1:2:4 block of size 0.23x0.23x0.23M placed at c/c distance of 2.0 M along the track. 12 mm dia rods in three horizontal layers tack welded with the angle posts including providing Retro-reflective tapes in Horizontal & vertical direction. Note : Released material will be the property of the contractor after the completion of work. Cost of cement to be paid separately

Item No.27 :- Providing and supplying in standard lengths Polyethelene Pipes, confirming to IS 4984 / 14151 / 12786 / 13488 with nesessary jointing material like mechanical connector i. e. thread / insert joint / quick release coupler joint / compression fitting joint or flanged joint excluding coupler/specials, including transportation and freight charges, inspection charges, loading / unloading charges, conveyance to the departmental stores & stacking the same in closed shade duly protecting from sunrays & rains, excluding GST levied by GI & GOM in all respect etc. complete.B) PE-100, 8 Kg/Sq. cm : i) 63 mm

ii) 75 mm

iii) 90 mm

iv) 110 mm

Item No.28 :- Lowering, Laying and Jointing H. D. P. E./ M. D. P. E. pipes in proper position including all specials by compression fitting/electrofusion and butt fusion jointing procedure as per relevent IS Code complete with all materials for jointing procedure like Electrofusion machine, Electric heater/butt fusion welding machine with hydraulic jack, top loading clamp etc. and all labours as directed by engineer in charge as per IS-7634 Part II i) 63 mm

ii) 75 mm

iii) 90 mm

iv) 110 mm

Item No.29 :- Providing and fixing in position M.S. ladder 0.50 M wide consisting of 75 x 10 mm M.S. flats as stringers and 16 mm dia M.S. bars in double rows as steps placed at 25 cm c/c including cost of material and labour involved,welding, anchoring and applying 3 coats of anticorrosive paint, etc. complete as directed by Engineer-in-charge.

Item No.30 :- Providing and supplying Leachate Treatment Plant of 30 m3/day based on MBR technology including transportations. as per specifications .The item includes all necessary acessories, fixtures and equipments required for installation of entire assembly etc. Complete. And Prior Approvel of Engineering Incharge is necessary. 1. ELECTRO-MECHANICAL EQUIPMENTS 1. Supply, installation, testing & commissioning of 1 No. SS 304 Perforated, Coarse Type Screen with suitable Manual garbage lifting arrangement. Size : 300 mm X 400 mm MOC : SS-304 1 Nos Make: Fabricated 2. Supply, installation, testing & commissioning of Automatic Fine Screw screen made of MOC CS + SS 304 filtering screen in RCC screen channel as per following specifications.Flow Rate:- 1.5 m3/h 1 No. Type- 2-3 mm punch hole type Make: Auric/Micro/Eq. 3. Supplying, installing, testing & commissioning of Mechnical Oil Skimmer of suitable capacity along with 100 liter HDPE Oil Collection tank.Type: Belt Type Make: Universal/Eq. 4. Supply, installation, testing & commissioning of non clogging type Raw Influent transfer pumps having CI casing & CI impeller, SS shaft complete with delivery header and all accessories, motor of required capacity. pressure gauge on delivery line with isolation cock, level controller to control the level for provision to control the level of sump automaticly. Pumps shall have following duty: 2Nos.(1W+1S) 4.1. Raw Influent Transfer Pump Flow Rate : 1.5 m3/hr Head : 8-10 mtr Type : Submersible type pump Solid handling : 30 MM 2 Nos. Make: Wilo/Kirlosker/Eq. Purpose: For Influent transfer from Collection tank to Bar Screen 4.2 EQT Transfer Pump Flow Rate : 1.5 m3/hr Head : 8-10 mtr Type : Submersible type pump Solid handling : 30 MM 2 Nos. Make: Wilo/Kirlosker/Eq. Purpose: For Influent transfer from Eqilization tank to Fine Screen 5. Supply, installation, testing & commissioning of Non clogging type centrifugal pumps capable of handling solids up to 8 mm having CI casing & CI impeller, CS shaft complete with all accessories, motor of required capacity, Pressure gauge on delivery line with isolation cock, level controller (with wiring) to control the level of sump automatically. Pumps shall have following duty: 2 Nos.(1W+1S) a. Sludge Recirculation pump Flow Rate : 6 m3/hr Head : 8-10 mtr Solid handling : 7 MM 2 Nos. Make: Wilo/Kirlosker/Eq. Purpose: For sludge transfer from MBR tank to Aeration tank and and sludge holding tank b. Supply and fixing of horizontal centrifugal pumps. The pumps shall have CI- Casing & impeller & CS shaft & sleeve, Mechanical/Gland Pack Seal are connected to a TEFC induction motor Motor to be suitable for 400/440 V, 3 Phase, 50 cycles AC power supply, including all necessary piping, valves, accessories, level controller complete complete as required. Pumps shall have following duty: 2Nos.(1W+1S) Flow Rate : 1.5 m3/hr Head : 8-10 mtr Make: Wilo/Kirlosker/Eq. Purpose: For suction of clear weater from MBR tank 2 Nos. 6. Air diffusion system 6.1. Supply, installation, testing & commissioning of 2 Nos. Twinlobe type rotary air blowers (1W + 1S) , capable of delivering 125 m3/hr with free air at 0.5 kg/cm2 driven through “V” belt or directly coupled through flexible coupling to a TEFC motor of suitable HP Suitable for 415 ± 10% volts, 3 phase, 50 cycles A/C supply. Including foundation and foundation bolts work.(1W+1S)=1Set Make: Beta/Eqv. Purpose: For air supply to, Aeration Tank, EQT & SHT 6.2 Supply, installation, testing & commissioning of 2 Nos. Twinlobe type rotary air blowers (1W + 1S) , capable of delivering 30 m3/hr with free air at 0.5 kg/cm2 driven through “V” belt or directly coupled through flexible coupling to a TEFC motor of suitable HP Suitable for 415 ± 10% volts, 3 phase, 50 cycles A/C supply. Including foundation and foundation bolts work.(1W+1S)=1Set Make: Beta/Eqv. Purpose: For air supply to MBR Module 7. Supply, installation, testing & commissioning of Non clog, Self Cleaning type air dispersion system capable of handling 3-5 cfm of air with oxygen transfer efficiency of 3-4% per / meter water depth. Air dispersion grid shall be assembled in modular form so that they can be replaced / repaired easily from plat form at the top. 7.1. Coarse bubble diffuser 1 Lot 7.2. Fine bubble diffuser 1 Lot Make: Airfin/Eq. 8. Providing and fixing all piping (as described below) including all fittings, ball valve, support for making the system complete. Upvc : Submerged air piping MS Epoxy : Air piping & pumped sewage riser (non-submerged) Upvc/MS Epoxy : Interconnecting pipe line after delivery header of pump/ filter 1 Lot Make: Jinda/Zoloto, uPVC: Astral 9. Supply, installation, testing and commissioning of MBR Module 0.04 micron pore size with all required accessories. Type: Hollow Fiber Purpose: For physical seperation of solid waste particles from water 1 Set 10. Supply, installation, testing and commissioning of Basket Centrifuge with all fittings & accessories. Basket diameter should be 500 mm with Poly Dosing system.(Manual Operation) 1 No. Purpose: For Drying of Sludge Make : Apollo/Eqvt 11. Supply, installation, testing and commissioning of Centrifuge Feed Pumps Complete with all fittings & accessories. Including foundation and foundation bolts.( 2Nos.- 1W+1S) Capacity : 1 m3/h Head : 10 mtr MOC : CI Purpose: For feed of sludge to Filter Press 2 Nos. Make: Wilo/Kirloskar/Eq. 12. Supply Installation Testing & Commissioning of Agitator with SS 304 Shaft of required capacity to be installed in mentioned below tanksa with all fittings and support. 12.i Flash Mixer Tank Agitator - 100 RPM 1 No. 12.ii Floculation Tank Agitator - 40-50 RPM 1 No. Make: Fabricated By PTBr 13. Supply, installation, testing & commissioning of Chemical dosing system (Lime and Alum) comprising of 100 ltrs LDPE tank with 0-12 LPH electronic metering type pump. 2 Set Make: Asia LMI/Eq. 14. Supply, installation, testing & commissioning of Poly dosing system comprising of 100 ltrs LDPE tank with 0-6 LPH electronic metering type pump. 1 Set Make: Asia LMI/Eq. 15. Supply, installation, testing & commissioning of Chlorine dosing system comprising of 100 ltrs LDPE tank with 0-6 LPH electronic metering type pump. (Location- Treated Water tank for disinfection purpose) 1 Set Make: Asia LMI/Eq. 16. Anaerobic Media(SAFF Media) in anaerobic tank Supply, installation, testing & commissioning of SAFF media anaerobic digestion of high COD/BOD. Size: 600 X 600 X 1200 mm MOC-PP/PVC Sheet Thickness- 3-4mm Make- PTBr/Eqvt Make: Suez/DOW/Eq. 2. ELECTRICAL AND INSTRUMENTATION 1. Design, fabrication, assembling, wiring, supply, installation, testing and commissioning of motor control centre od non-compartmentalized type fabricated out of 14/16 gauge CRCA sheet steel. Cable gland plates shall be provided on top as well as at the bottom of the panels. Panels shall be treated with all anticorrosive process before painting as per specifications with 2 coate of red oxide primer and final approved shade of powder coated paint. 2 Nos. earthing terminals shall be provided for 3 phase, 4 wire, 50 Hz supply system. Lifting hooks shall also be provided in case of large panels. Approval shall be taken for each panel before fabrication. MCC –1 (Leachate Treatment Plant) 1 Nos. Make : PTBr -CPRI Approved 2. Cable & Cable trays Suppy, installation, testing & commissioning of Cable and GI cable trays as required to complete the electrical connection with all equipments. Make : Cable- Polycab & cable tray- Super steel 1 Lot. 3. Suppy, installation, testing & commissioning of electro-mangnetic type flow meter at inlet of raw sewage transfer pump and outlet of permeate pump. Make: Aster / Electronet/Eq. 1 Nos. Purpose : To Measure flow quantity with time 4. Supply, Installation, Testing & Commissioning of float type water level indicator for operation of the system connected to control panel for automatic switching ON / OFF of each pump. Make: Minilec/Cirrus/Eq. 1 Lot. Purpose : For control level of Influent in tank 5. Supply, Installation, Testing & Commissioning of pressure gauges with in all respect Make: H Guru/Eq. 1 Lot. Purpose : For Measure & Indicate the pressure into vessel 6. Supply, Installation, Testing &Commissioning of Air rota meter for air flow calculation. Make- Microflow/Eq. 2 Nos. 7. Supply, Installation, Testing &Commissioning of pH meter at Hopper bottom tank. Range- 0 to 14 Make- Aster/Eq. b. Supply and fixing of horizontal centrifugal pumps. The pumps shall have CI- Casing & impeller & CS shaft & sleeve, Mechanical/Gland Pack Seal are connected to a TEFC induction motor Motor to be suitable for 400/440 V, 3 Phase, 50 cycles AC power supply, including all necessary piping, valves, accessories, level controller complete complete as required. Pumps shall have following duty: 2Nos.(1W+1S) Flow Rate : 1.5 m3/hr Head : 8-10 mtr Make: Wilo/Kirlosker/Eq. Purpose: For suction of clear weater from MBR tank 2 Nos. 6. Air diffusion system 6.1. Supply, installation, testing & commissioning of 2 Nos. Twinlobe type rotary air blowers (1W + 1S) , capable of delivering 125 m3/hr with free air at 0.5 kg/cm2 driven through “V” belt or directly coupled through flexible coupling to a TEFC motor of suitable HP Suitable for 415 ± 10% volts, 3 phase, 50 cycles A/C supply. Including foundation and foundation bolts work.(1W+1S)=1Set Make: Beta/Eqv. Purpose: For air supply to, Aeration Tank, EQT & SHT 6.2 Supply, installation, testing & commissioning of 2 Nos. Twinlobe type rotary air blowers (1W + 1S) , capable of delivering 30 m3/hr with free air at 0.5 kg/cm2 driven through “V” belt or directly coupled through flexible coupling to a TEFC motor of suitable HP Suitable for 415 ± 10% volts, 3 phase, 50 cycles A/C supply. Including foundation and foundation bolts work.(1W+1S)=1Set Make: Beta/Eqv. Purpose: For air supply to MBR Module 7. Supply, installation, testing & commissioning of Non clog, Self Cleaning type air dispersion system capable of handling 3-5 cfm of air with oxygen transfer efficiency of 3-4% per / meter water depth. Air dispersion grid shall be assembled in modular form so that they can be replaced / repaired easily from plat form at the top. 7.1. Coarse bubble diffuser 1 Lot 7.2. Fine bubble diffuser 1 Lot Make: Airfin/Eq. 8. Providing and fixing all piping (as described below) including all fittings, ball valve, support for making the system complete. Upvc : Submerged air piping MS Epoxy : Air piping & pumped sewage riser (non-submerged) Upvc/MS Epoxy : Interconnecting pipe line after delivery header of pump/ filter 1 Lot Make: Jinda/Zoloto, uPVC: Astral 9. Supply, installation, testing and commissioning of MBR Module 0.04 micron pore size with all required accessories. Type: Hollow Fiber Purpose: For physical seperation of solid waste particles from water 1 Set 10. Supply, installation, testing and commissioning of Basket Centrifuge with all fittings & accessories. Basket diameter should be 500 mm with Poly Dosing system.(Manual Operation) 1 No. Purpose: For Drying of Sludge Make : Apollo/Eqvt 11. Supply, installation, testing and commissioning of Centrifuge Feed Pumps Complete with all fittings & accessories. Including foundation and foundation bolts.( 2Nos.- 1W+1S) Capacity : 1 m3/h Head : 10 mtr MOC : CI Purpose: For feed of sludge to Filter Press 2 Nos. Make: Wilo/Kirloskar/Eq. 12. Supply Installation Testing & Commissioning of Agitator with SS 304 Shaft of required capacity to be installed in mentioned below tanksa with all fittings and support. 12.i Flash Mixer Tank Agitator - 100 RPM 1 No. 12.ii Floculation Tank Agitator - 40-50 RPM 1 No. Make: Fabricated By PTBr 13. Supply, installation, testing & commissioning of Chemical dosing system (Lime and Alum) comprising of 100 ltrs LDPE tank with 0-12 LPH electronic metering type pump. 2 Set Make: Asia LMI/Eq. 14. Supply, installation, testing & commissioning of Poly dosing system comprising of 100 ltrs LDPE tank with 0-6 LPH electronic metering type pump. 1 Set Make: Asia LMI/Eq. 15. Supply, installation, testing & commissioning of Chlorine dosing system comprising of 100 ltrs LDPE tank with 0-6 LPH electronic metering type pump. (Location- Treated Water tank for disinfection purpose) 1 Set Make: Asia LMI/Eq. 16. Anaerobic Media(SAFF Media) in anaerobic tank Supply, installation, testing & commissioning of SAFF media anaerobic digestion of high COD/BOD. Size: 600 X 600 X 1200 mm MOC-PP/PVC Sheet Thickness- 3-4mm Make- PTBr/Eqvt Make: Suez/DOW/Eq. 2. ELECTRICAL AND INSTRUMENTATION 1. Design, fabrication, assembling, wiring, supply, installation, testing and commissioning of motor control centre od non-compartmentalized type fabricated out of 14/16 gauge CRCA sheet steel. Cable gland plates shall be provided on top as well as at the bottom of the panels. Panels shall be treated with all anticorrosive process before painting as per specifications with 2 coate of red oxide primer and final approved shade of powder coated paint. 2 Nos. earthing terminals shall be provided for 3 phase, 4 wire, 50 Hz supply system. Lifting hooks shall also be provided in case of large panels. Approval shall be taken for each panel before fabrication. MCC –1 (Leachate Treatment Plant) 1 Nos. Make : PTBr -CPRI Approved 2. Cable & Cable trays Suppy, installation, testing & commissioning of Cable and GI cable trays as required to complete the electrical connection with all equipments. Make : Cable- Polycab & cable tray- Super steel 1 Lot. 3. Suppy, installation, testing & commissioning of electro-mangnetic type flow meter at inlet of raw sewage transfer pump and outlet of permeate pump. Make: Aster / Electronet/Eq. 1 Nos. Purpose : To Measure flow quantity with time 4. Supply, Installation, Testing & Commissioning of float type water level indicator for operation of the system connected to control panel for automatic switching ON / OFF of each pump. Make: Minilec/Cirrus/Eq. 1 Lot. Purpose : For control level of Influent in tank 5. Supply, Installation, Testing & Commissioning of pressure gauges with in all respect Make: H Guru/Eq. 1 Lot. Purpose : For Measure & Indicate the pressure into vessel

Item No.31 :- Providing lab testing reports of the construction material like cement, steel, bricks, sand, etc Schedule of Testing charges as per PWD DSR (Test mentioned in DSR) 1) Steel Anti-Corrosive Test Resistance to apptied Voltage.(30 Days Test)( Set of 2 Bars )

2) Steel -Upto 16 mm dia (Set of 3 Bars) (Tensile strength, %, Elongation, Yield Stress,weight-Per Meter, Bend / Rebend Test, Proof Stress.)

3) Steel -more 16 mm dia (Set of 3 Bars) (Tensile strength, %, Elongation, Yield Stress,weight-Per Meter, Bend / Rebend Test, Proof Stress.)

4) Sand (Fine Aggregate)

5) Cement Concrete -Mix design -3 vendors (M20, M30)

6) Cement Concrete -Compressive strength (3 cube)

7) Mortar

8) water

9) Rebound hammer

10) Ultrasonic Pulse Velocity Test