Municipal Corporation Of Greater Mumbai Tender

Light 22, Fixture body should be made in die-cast alu- minum only. It's Upper frame made in die-cast aluminum, with threaded coupling G 3/4" for fixing, Bottom frame tilt- ing, composed by a ring made in die-cast aluminum. A Gas- ket is provided between the upper and bottom frames. Painted with polyester powder coating in Standard Grey Matt finish Colou. IP Rating - IP 66. overall systems effi- ciency should be 105lm/W minimum. (Same should be sup- ported by LM79 report) Height – 390mm ,Diameter – 700mm, Weight - 11Kg, Area Exposed to Wind(S) - 0.12 m2. Power LED's Module (with CREE-XPG2 LED's Individual LED's Minimum Luminous Flux (lm) is 164lm @ 350mA (@85 C) same should be supported by LED manufacturer's tech sheet) in complaince with IEC62031 (supporting type test report should be submitted), on Printed Circuit Board with metal core plate. Colour Rendering Index:Ra70. Pro- grammable elctronic Power Supply (with DALI/1-10VFea- ture) for LED Module, which offers Protection agiants short circuit,Over-Voltage & Over-Current, with in-built surge- protection upto 6kv (differntial)/10kv (common) (anad- dtional surge protection devise of 10kv also provided in built the fixture). Moduler (2X2) refractive lens in PMMA with type -II/III/IV photometric distribution potions. NTC sensor on LED plate for control of dangerous temperatures. LM80 reported LED filetime is L90@50,000 hours mini- mum. (same should be supported by LM80 report from NVPAL accretited lab) & Estimated LED Lifetime is LM80@ 100,000 hours (Ta-25 C) minimum. Signle Castore Bracket 2M hight Castore design bracket which is made in combination of Hot dip garvanised mild steel pipe section & cast iron elements. Entire bracket shall be made to get 930mm horizonal arm lenth & provide pleasing aesthetics. Decorartive Cast iron pole top strts from bottom with a ring section of dia.67mm followed by a ring of dia.75mm, radi- ally incrases to 100mm dia. for a height 15mm, then radi- ally reduces to 46mm for a height 20mm followed by a jack shaped section (45mm(W20mm(H), followed by a ring of dia.60mm wich is followed by a Conical section (bottom dia,40mm & top dia.10mm, 140mm(H) with sphere shape (30mm) dia.) on top-total height of the pole top is 230mm & weight is 4kgs. Approved Make - SUNCITY / NERI

ARCHITECTURAL 10m (Castore DESIGN) POLE :JM.07.18.06610M height Single arm Pole Made in combi- nation of hot dip galvanised mild steel pipe sections 140mm dia. & 114mm dia.,&Architectural Base design starting with circular plinth of 400mm dia. for 100mm height, fol- lowed by a ring of 400 dia gradually tapering upto dia 200mm for 600mm height which is followed by decorative portion of 300mm(W)x80mm(H) which is followed by a por- tion starts with 248mm(W) & gradually tapering upto 155mm dia. then gradually increasing upto 225mm. as ap- proved by the concerned Engineer. the total height of deco- rative cast iron base is 960mm and weight-56kgs.. Decora- tive cast iron base should be provided with a flush door of height 322mm, width 153mm and Depth 31mm .Decorative Ring-1(140mm/114mm-5kgs.) & Ring-2(114mm/60mm- 3kgs.) are made of cast iron. Entire pole shall be made to provide pleasing aesthetics as approved by Concerned Engi- neer in-charge. After Fabrication, Entire Pole is hot dip gal- vanized(60 microns Minimum ) for the effective corrosion resistance . The hot dip Galvanised pole should be provided with an inbuilt junction box to fix 32A connectors and 6A MCB, at the bottom - the inbuilt box should have a flush door of suitable size. The decorative pedastal to be mounted on a suitable size steel plate. This mounting steel plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed RCC foundation. wind pressure calculation as per IS 875(part-3) & structural calculation report as per EN40 should be sub- mitted to verify the pole design. Pole & Cast iron parts are painted in 3 layer coating(coating thickness-100 microns minimum) in which 1st layer with etch primer, 2nd layer with epoxy primer & 3rd final layer with PU paint - cus- tomised colour Metallaic Grey. & only Joint rings & pole top will be in Golden Colur Approved Make - SUNCITY / NERI

Design and Casting of suitable shallow foundation with 1:2:4 grade concrete