Municipal Corporation Of Greater Mumbai Tender

IP 42 Wall/column Mounted distribution board with one Nos of 16A DP MCB as incomer and 4 Noss 6/10A SP MCB as outgoing (8way SPN DB)

Cable end terminations for LV, XLPE/PVC insulated, PVC sheathed, armoured/ unarmoured cables including supply and fixing of Double compression cable glands, stripping of cable insulation, supply and fixing of tinned plated copper lugs for copper cables for all phases and crimping the same to the conductor for the following cables. Miscellaneous items like cable lugs, G.I nut - bolts and G.I washers , consumables and other hardware materials as required to make the installation complete, are in the scope. All G.I Nut, bolt and washers shall be HDGI with 80 micron. One set of termination includes gland, lugs for cable core & accessories Providing, installing and giving test of submersible pumpset directly coupled to submersible electric motor complete with suction strainer, antithrust streamlined non return valve, minimum 4 m submersible type copper conductor cable and 2 pairs of suitable size 10 mm thick erection clamps, 4 m lifting chain and 1 submersible cable connection kit shall be provided with each pump set.

Cable End Termination For Copper Cables – 3C x 2.5 Sq.mm

1.1 kV grade stranded Cu conductor, XLPE insulated, extruded PVC inner and FRLS outer sheathed, galvanised steel round or strip armoured cables (SP-ME-TS- 6

1st category Cu armoured cables FRLS outer sheathed- 3C x 2.5

Sheet Moulding compound (SMC) Junction Box, for Outdoor

SMCJB - 1414, Hinged cover, Size 170 x 170 x 105mm

Starter for Motors : (Complete with Interconnections & Wiring) (SP-ME-TS- 1): Following rating starters. Enclosure for starter shall be Corrosion resistant powder coated CRCA enclosure with IP54 protection class shall be suitable for chemical factories, polluted industrial and dusty agricultural environment. Starters shall be provided with terminal block with proper terminal marking for ease of wiring. Terminal block can accommodate both aluminum & copper cables. Starter shall be provided with ON / OFF Indication lamps and Start / Stop Push buttons. Components for motor starter shall have type 2 co-ordination compliance and built in single phase protection. Colour shade shall be RAL 7032 smoke gray as per IS 5.

Single Phase DOL starter, fractional H.P To 1 H.P

SUPPLY & INSTALLATION OF ANGLE IRON FRAME WORK

50 x 50 x 6 mm of M.S.angle.

Flat bars 50 mm x 6 mm thick.

Readymade 2500mm standard length, prefabricated, perforated cable tray from MS sheet and then hot dip galvanised, of following sizes and associated accessories such as coupler plates, tees, elbow etc. Galvanisation thickness shall be minimum 86 Micron.

G.I. Cable tray with all other accessories 100 x 25mm (W x H) -(16 SWG - 1.6mm) without cover

Readymade 2500mm standard length, prefabricated, GI trunking from MS sheet and then hot dip galvanised, of following sizes and associated accessories such as coupler plates, tees, elbow etc. 50 mm side flanges shall be provided.Galvanisation thickness shall be minimum 86 Micron. cost of trunking shall be included junction box of suitable size, and all other accessories required to complete the work.

G.I. Trunking / Duct / Raceway & all other accessories – 150 x 40mm (W x H) - (14 SWG - 2mm) with cover without partition

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot &cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge

25 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge.

25 mm nominal outer dia Pipes

Providing, fixing and testing heavy quality gun metal or brass ball valve with screwed ends 20kgm class on GI or copper pipe lines(Leader/ZOLOTO make) 15 mm (1/2") dia.

Providing, fixing and testing heavy quality gun metal or brass ball valve with screwed ends 20kgm class on GI or copper pipe lines (Leader/ZOLOTO make) 25 mm (1") dia.

Excavation by chiseling by manual operations, pneumatic breaker, hammer, drilling, compressor breaker, jack hammer etc. over areas for basements, roads, land/plot developement etc. in hard rock, reinforced concrete, Bituminous macadam for all depths/lifts including manual dewatering, filling the selected excavated earth at the locations as directed, in layers not more than 200mm thickness, watering, consolidating, compacting to achieve not less then 97% Modified Proctor density conforming to relevant IS, stacking the selected material in measurable heaps for future use within owners space or disposing within an initial lead of 150m as directed, loading, unloading, leveling excluding shoring, strutting etc. complete as by Engineer-inCharge. Note: 1) The rate includes the handling/supporting the existing utilities such as cables, drains, pipes, water mains etc. 2) It also includes the royalty and other taxes if any.

Supplying G.I C Class Pipes having embossed ISI mark on it and Conforming to IS: 1293 (Latest Edition) of the following diameter excluding all local and centraltaxes,octroi,inspection charges, transportation to stores etc complete in all respect as directed by Engineer in Charge. Note : Only GI pipe brands from the MCGM approved vendor list shall be used, all pipe and pipe fittings shall be C class (heavy grade) having ISI marking.

80mm

Supplying & spreading of one or more layers of compacted crushed coarse agg. with alternate application of bituminous binder & key aggregate with the requirements of MORTH, Rolling with 10/12 mt roller using VG-30 grade bitumen (1% Antistripping agent) to serve as base course and inconformity with the line, level and cross sections shown on the drawings or as directed by the Egg., thickness of individual course shall not exceed 50 mm. (As per prevailing MCGM specification for Roadwork Clause No. 352) SQM 475.00 R3-RW-5-03 P/L premix hot mi