Indian Institute Of Science Education And Research Tender

Extra for cutting reinforcement bars manually/ by mechanical means in R.C.C. or R.B. work (Payment shall be made on the cross sectional area of R.C.C. or R.B. work) as per direction of Engineer In-charge.

Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead. Quoted rate shall be including GST , transportation , lead , lift , scaffolding etc complete. Nothing extra shall be paid separately.

Deployment of Tempo ( 407 )/tractor trolley and adequate Manpower for Shifting of debates , unserviceable material to IISER Scrap yard or dumping yard as per site requirement. Material to be collected from corridors of Main Building ( G+2 ) as per directions of Engineer In-charge , unserviceable material to be shifted to scrap yard. Quoted rate shall be including the hire charges, labours, transport, fuel , tools tackles, operators charges etc , insurance of equipment and operator, etc. complete. Copy of valid license shall be available with the driver along with the Registration Certificate ( RC ) copy and shall be submitted to IISER Pune for records. Nothing extra shall be paid separately. Actual number of trips as per Log Sheet duly approved by Engineer In-charge or his representative shall be measured for payments. Agency shall maintain log-sheet of deployment and get daily certified from department on same day and shall be submitted along with running account bill for payments. Quoted rate shall be including cost of labour , tools , GST ,taxes , minimum labour wages , etc complete. Nothing extra shall be payable separately. Minimum volume to be shifted shall be 100 cut unit.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources)

Providing and laying in position ready mixed plain cement concrete, with cement content as per approved design mix and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for plain cement concrete work, including pumping of R.M.C. from transit mixer to site of laying and curing, including the cost of centring, shuttering and finishing, including cost of curing, admixtures in recommended proportions as per IS : 9103 to aeeelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineering- charge. Note : 1) Excess/less cement used than specified in this item is payable/recoverable separately. I All works up to plinth level : M-30 grade plain cement concrete (cement content considered @ 350 kg/cum). Quoted rate shall be including GST , transportation , lead , lift , scaffolding etc complete. Nothing extra shall be paid separately.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete up to/above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. Quoted rate shall be including GST , transportation , lead , lift , scaffolding etc complete. Nothing extra shall be paid separately.

Brick work with non modular fly ash bricks conforming to IS:12894, class designation 6 average compressive strength 60kg/sqcm in below plinth level. Quoted rate shall be including GST , transportation , lead , lift , scaffolding etc complete. Nothing extra shall be paid separately.

Internal Plastering with 12 mm cement plaster 1:2 (1 cement : 2 stone dust). Quoted rate shall be including all taxes , duties , material and labour cost , GST, etc complete. Nothing extra shall be paid separately.

Earth work in excavation and backfilling by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead up to 50 m and lift up to 1.5 m, as directed by Engineer-in-charge. All kinds of soil. Quoted rate shall be including GST , transportation , lead , lift , scaffolding etc complete. Nothing extra shall be paid separately.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead within/excavated within the campus in borrow pits. Quoted rate shall be including GST , transportation , lead , lift , scaffolding etc complete. Nothing extra shall be paid separately.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. Quoted rate shall be including GST , transportation , lead , lift , scaffolding etc complete. Nothing extra shall be paid separately.

Structural steel work Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, bending as per drawing, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes.

Structural steel work Steel work in any steel available in the campus built up tubular (round, square or rectangular hollow tubes etc.) trusses/ Angle/Tees/Channels etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Quoted rate shall be including of dismantling of existing MS material and re-fabrication to the approved shape as per direction of Engineer In-charge

Providing and fixing mild steel round holding down bolts with nuts and washer plates complete.

Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 mm dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of Engineer-in-charge. 10 x 150 mm.Quoted rate shall be including GST , transportation , lead , lift , scaffolding etc complete. Nothing extra shall be paid separately.

Finishing walls with Acrylic Smooth exterior paint of required shade : Old work (Two or more coat applied @ 1.67 litre/ 10 sqm) on existing cement paint surface. Approved Make: Dulux Weathershild Flexx Exterior / Asian Duralife / NEROLAC Top Guard . .Quoted rate shall be including GST , transportation , lead , lift , scaffolding etc complete. Nothing extra shall be paid separately.

Supply and installation of Water jet car washing machine of with 1000 liter Sintex Tank, hose connections , ball cock, tank nipple , 25mm brass valve etc complete.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of comigation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineering-charge. The sheet shall be fixed as per curvature in drawing using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of comigation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineering-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. Agency will collect sheet from IISER Campus.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :Crimp curve

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture