Indian Institute Of Science Education And Research Tender

Providing & fixing false ceiling at all height including providing & fixing of framework made of special section, power pressed from M.S. sheets and galvanised with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleat of size 25mm wide x 1.6mm thick with flanges of 27mm and 37mm, at 1200mm c/c, one flange fixed to the ceiling with dash fastener 12.5mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25 x10 x0.50mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I chanels 45 x15 x 0.90mm running at the spacing of 1200 mm c/c, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26 mm each having lips of 10.5mm, at 450mm c/c, shall be fixed in a direction perpendicular to G.I intermediate channel with connecting clip made out of 2.64mm dia x 230mm long G.I wire at every junction, including fixing perimeter channels 0.50mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/ partitions with the help of Rawl plugs at 450mm centre, with 25mm long dry wall screws @ 230mm interval, including fixing of Calcium Silicate Board to ceiling section and perimeter channels with the help of dry wall screws of size 3.5 x25mm at 230mm c/c, including jointing & finishing to a flush finish of tapered and square edges of the board with ecommended jointing compounds, jointing tapes,finishing with jointing compounds in three layers covering up to 150mm on both sides of joints and two coats of primer suitable for boards, all as per manufacture's specification and also including the cost of making opening for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specificaton and direction of the Engineer in charge but excluding the cost of painting with: 8 mm thick Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process. Quoted rates shall be including removal of old damaged false ceiling GST , labour, lead , lift , trasportation etc complete. Nothing extra shall be paid seperatly.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required ncluding cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) For fixed ortion: Powder coated aluminium (minimum thickness of powder coating 50 micron) Quoted rates shall be including GST , labour, lead , lift , trasportation etc complete. Nothing extra shall be paid seperatly. Approved Make JINDAL/BARUKA/Indian Aluminium Co.

Fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required ncluding cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) For fixed portion : Aluminium Pipes shall be issued by IISER Pune.Quoted rates shall be including GST , labour, lead of aluminium pipes from stores with campus , lift , trasportation etc complete. Nothing extra shall be paid seperatly.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) .Powder coated aluminium (minimum thickness of powder coating 50 micron). Quoted rates shall be including GST , labour, lead , lift , trasportation etc complete. Nothing extra shall be paid seperatly. Approved Make JINDAL/BARUKA/Indian Aluminium Co : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots/Sliding and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron) Quoted rates shall be including GST , labour, lead , lift , trasportation etc complete. Nothing extra shall be paid seperatly.

Providing and fixing glazing in aluminium Door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge . Quoted rates shall be including GST , labour, lead , lift , trasportation etc complete. Nothing extra shall be paid seperatly. (Cost of aluminium snap beading shall be paid in basic item): With With float glass panes of 8 mm thickness.Quoted rates shall be including GST , labour, lead , lift , trasportation etc complete. Nothing extra shall be paid seperatly.

Fixing of glazing in aluminium Door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge . Quoted rates shall be including GST , labour, lead , lift , trasportation etc complete. Nothing extra shall be paid seperatly. (Cost of aluminium snap beading shall be paid in basic item): With glass panels issued by IISER Pune. Quoted rates shall be including GST , labour, lead of glass panel from stores located within campus, lift , trasportation etc complete. Nothing extra shall be paid seperatly.

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. With stainless steel cover plate minimum 1.25 mm thickness. Quoted rates shall be including GST , labour, lead , lift , trasportation etc complete. Nothing extra shall be paid seperatly.

Providing and fixing 100mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.Quoted rates shall be including GST , labour, lead , lift , trasportation etc complete. Nothing extra shall be paid seperatly. Approved Makes Godrej/Dorma/Hafle

Providing and fixing Stainless Steel H handle of 300mm size etc. complete pair of in-out handle as per direction of Engineer-incharge. Quoted rates shall be including GST , labour, lead , lift , trasportation etc complete. Nothing extra shall be paid seperatly. Approved Makes Godrej/Dorma/Hafle

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 150x10 mm.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : Old work (one or more coats) Ceiling Painting.Quoted rate shall be including at taxes , duties , royalties , lead, lift , trasportation , insurance , GST , etc. Nothing extra shall be paid seperatly. Approved Makes Nerolac/Dulux/Asian.

Removing white or colour wash/any wall paint by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete including disposal of scrapped material, cleaning of flooring etc complete.Quoted rate shall be including at taxes , duties , royalties , lead, lift , trasportation , insurance , GST , cost of etc. Nothing extra shall be paid seperatly.

Providing and applying white cement based putty of average thickness 1mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.Quoted rate shall be including at taxes , duties , royalties , lead, lift , trasportation , insurance , GST , etc. Nothing extra shall be paid seperatly. Approved Makes Nerolac/Dulux/Asian.

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre.Minimum 2 coats .Quoted rate shall be including at taxes , duties , royalties , lead, lift , trasportation , insurance , GST ,etc. Nothing extra shall be paid seperatly. Approved Makes Nerolac/Dulux/Asian.

Wall painting with synthetic enamel paint of satin finish approved brand to give an even shade: One or more coats on old work upto even shade. Quoted rate shall be including at taxes , duties , royalties , lead, lift , trasportation , insurance , GST , cost of sample and laboratory fees etc. Nothing extra shall be paid seperatly. Shade and scheme shall be got approved from Engineer In-charge before taking-up work. Application methodology as specifified by Manufactorer. Approved Makes Nerolac/Dulux/Asian.

Painting with synthetic enamel paint of satin finish approved brand and manufacture to give an even shade : Two or more coats on new work. Quoted rate shall be including at taxes , duties , royalties , lead, lift , trasportation , insurance , GST , etc. Nothing extra shall be paid seperatly. Shade and scheme shall be got approved from Engineer In-charge before taking-up work. Application methodology as specifified by Manufactorer. Approved Makes Nerolac/Dulux/Asian.

Removal and refixing of modular false ceiling of size 595X595 along with grid system and stacking grid and tiles polypacks in suitable boxes at location in IISER PUNE campus as directed by Engineer in charge. Rate shall be inclusive of scaffolding etc. complete . Nothing extra shall be paid separately.

Providing and fixing of grid for modular false ceiling of size 595X595 along with grid system , quoted rate shall be including removal of existing damaged/bent unservisable grid. Armstrong

Providing and laying modular false ceiling tiles of size 595X595 , quoted rate shall be including removal of existing damaged/bent unservisable tile, disposal to dumping ground within campus. Armstrong Bioguard

Repairs to Gypsum/Calcium Silicate Partition/ceiling by providing and fixing 8mm calcium silicate board single/double skin on existing G.I. frame/ceiling including jointing and finishing flush to existing finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer , putty and 2 coat painting suitable for board as per manufacture's specification and direction of engineer in charge all complete. Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process with Compressive Strength 225 kg/sq.cm, Bending Strength 100 kg./ sq.cm . Quoted rate shall be including removing of existing damaged ceiling , making proper supporting arrangement , scaffolding upto 5 meter etc complete. Actual area of board shall be measured for payment.

Providing and fixing wall paneling by 8mm tapered edge calcium silicate board made with calcareous & siliceous materials reinforced with cellulose fiber manufactured through autoclaving process to give stable crystalline structure with compressive strength 225 kg/ sq.cm, Bending strength 100 kg/sq.cm over frame work of aluminium /GI/MS etc all complete as per the drawing & directions of engineer-in-charge, the joints of the boards are finished with specially formulated jointing compound and 48 mm wide jointing tape to provide seamless finish.Frame works shall be measured in respective items. Quoted rate shall be including removing of existing damaged ceiling , making proper supporting arrangement , scaffolding upto 5 meter etc complete. Actual area of board shall be measured for payment.

Misc plumbing works associated with closing of existing water points , drain points , closing by using vitrified time cut to appropriate size and shape etc cmplete.

Providing and fixing wall panelling of 12mm thick BWP grade plywood with 1mm thick decorative laminate on exposed surfaces of plywood . Quoted rate shall be including supporting wood work in Sal wood / plywood backing of suitable size as per site requirment for door architraves' , wall panelling. Laminate shall be decorative type wood grain shade. Quoted rate shall be cost of material , labour , screws , glue , GST etc. complete. Nothing extra shall be paid separately.

Providing and fixing APP (Atactic Polypropylene Polymer) modified prefabricated five layer 2 mm thick water proofing membrane , black finished reinforced with glass fibre matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrance manufacture of density at 25°C, 0.87 - 0.89 kg/ litre and viscocity 70 - 160 cps. Over the primer coat the layer of membrane shall be laid using Butane torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 350/300 N/ 5 cm. Tear strength in longitudinal and transverse direction as 60/80N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacture of membrane. 2mm (for corrugated roof sheets) . Item to be executed over self tapping screws on precoated sheets with size of application as 25mm X 25mm. Each screw treated with APP shall be is measured for payments.

Providing and fixing aluminium composite panel in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3.5mm thick FR grade mineral core sandwiched between wo Aluminium sheets (each 0.25mm thick). The aluminium composite panel sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade using tainless steel screws, nuts, bolts, washers, cleats,weather silicone sealant, backer rods etc.

SEALING OF HOLES BY EXTERIOR GRADE SILICON SEALANT OF DOW CORNING FOR STRUCTURAL GLAZING PURPOSE WITH GOOD ADESION BETWEEN METAL AND FRP/GLASS/ACP. DOW 895 / DOW 995 WITH APPLICATION NOZZLE-GUN PUSH MECHANISUM. BOTTLE OF 300ML

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.Quoted rate shall be including GST , labour , fuel etc complete. Nothing extra shall be paid seperatly.

Providing and applying Kemperol V210 treatment to precoated roofing surface including two coats of Kemperol EP primer followed by sprinkling silica sand (0.3 to 0.7mm), Applying 2/3 of KEMPEROL V 210 on the surface with the help of nylon roller/brush. Then roll out the KEMPEROL AP Fleece. Remove all wrinkles and then saturate completely with remaining 1/3rd of KEMPEROL V 210 mixture. Self curing of 3days etc complete or directed by project In charge. A solid base of morter / rubber coving / metal sheeting shall be provided before applying membrane. Single coat bitumastic paint shall be applied for protection of membrane . Quoted rate shall be including cost of material , labour , GST , scaffolding etc complete. Nothing extra shall be paid seperatly.

Supply, installation, testing and commissioning of LT panel as per following specifications. Drawing, SLD, GA, BOM & specifications should be submitted to IISER Pune for approval before manufactureing of panel.Supply, installation, testing and commissioning of 3 phase, 4 wire, 415 KV, 0.8 PF, 50 HZ panels. The fabrication shall be made with 14 SWG cold rolled sheet with M/C pressing, powder coated. The surface shall be rigorously treated for derusting in 7 tank process with dephosphating & paintingwith at least 2 coats of approved paint. The panel shall be totally enclosed metal clad type with double gasketting with rubber/ resin lining. The panel shall be having control directory pasted inside the panel. The panel shall be mounted on existing trench/ floor & shall have cable entry provision from the top & bottom with suitable alley as the case may be.The panel shall be tested for the same KA rating of the relevant highhest rating of MCCB. All comorents shall be from ISO-9001 companies and shall have relevant IS/IES approvals without fail. The panel shall be fully interlocked as required. The panel shall include baseframe channel support. ( The single line daigram shall be closely followed) 1. The panel shall be design as per norms of CEIG/ PWD/ CPWD/ Maharashtra State Electricity Distribution Company Ltd.2. Auxilliary contractor to be provided along with Auto-manual switch where ever required.3. Ventilators shall be provided for Panels with rated bus bars.4. Al bus earthing shall be provided for all panels.5. Circuit Breakers shall confirm IS 13947-2IEC 947-26. All doors to have double rubber gasket with shutter assembly & door seating frame.7. The UPS outgoing panels shall have neutral busbars double the size of phase.8. All breaker to have breaker manufacturer's factory made Spreaders.9. In any case Aluminium busbar should not be connected directly to breaker without spreaders.10. The control wiring has to be in appropriate size with MCB protection.11. Irrespective of the Amp. Capacity all breakers shall be connected to the breakers using busbar only.12. All vertical bus bars in bus bar alley shall have bottem supports.13. All panels shall have top entry only.14. Panel earthing strip should come out vertically on top the panel.15. Earthing bus shall be coated to give a look of tin.16. All indication should be proper colour and with protection of MCB.17. All meters should have protetion of MCB.18. Door earthings shall be provided for all doors.19. Suitable for termination of upto 3 1/2 C x 35 sqmm al arm cable for each outgoing feeder20. Suitable for termination of upto 3 1/2 C x 95 sqmm al arm cable for each incoming feederLT PANEL for RAW, UPS OR VRF A) Cubicle Details:Material of construction- CRCA-14 SWGIP Protection- IP-52 as per IS 2147Indoor cubicle type free standing & floor mountingfront/Rear panels- Hinged doors/ Removeble typeGland plates-Undriled, dust & vermin proofCables entry details:Incoming- All cables are from topOutgoing- All outgoings by cables from top B) Meters:3 Phase 4 Wire, 440 Volts, Digital meters for Parameters Volt, Amp, Hz, KVA, KW etc, auto scrolling facility, panel mounting on door, suitable for 96 x 96mm. Range- 0-500V, 10 Amps.Digital multifunction meter with KWH meter with CT's and selector switch.Range-400 Amps.BUS BAR: 400 A, TPN, 415V, 3 Phase, 50Hz, Aluminium Bus Bar.Bus Bar Supports- FRPBus Bar sleeves- Heat shirkable- colour coded.internal & control wiring- To be with ferrulesHeat resistant type, 1100V grade single core copper flexible. C) Incomer:MCCB:Quantity- 01 No.Rating- 125 amps- 35 KA. (Legrand/ L&T/ Siemense)Type-MDOOperation- manualNo. of Poles- 3 P + neutral linkRelease- OC/ SC/ EF/ ST.ndications- RYB/ Off/ ON/ Trip.Other features- All standard.Auxillary Contactors:Quantity- As required.Rating- 6 Amps.CT's- Measurement- 2 sets.Class- 15 VA burden.Type- Cast resin.Ratio- 125/ 5D) Outgoing:MCCB:Quantity- 05 Nos.Rating- 63 amps- 25 KA. (Legrand/ L&T/ Siemense)TypeManualNo. of Poles- TPNRelease- OC/ SC/ ST.Indications- On

Supply of Following size of XLPE insulated and XLPE/PVC sheathed power cable of 1.1 KV grade. 1 C x 16 sq mm copper Conductor flexible green colour cable. quoted rates shall be including all taxes,duties,royalties,lead,lift,transpotation,GST etc complete.Nothing shall be payable separtely. Work shall be executed as per direction of engineer in charge,IISER Pune. Actual cable laid at site shall be measured for payments.

Supply of Following size of XLPE insulated and XLPE/PVC sheathed power cable of 1.1 KV grade. 1 C x 6 sq mm copper Conductor flexible green colour cable. quoted rates shall be including all taxes,duties,royalties,lead,lift,transpotation,GST etc complete.Nothing shall be payable separtely. Work shall be executed as per direction of engineer in charge,IISER Pune. Actual cable laid at site shall be measured for payments.

Supply of Following size of XLPE insulated and XLPE/PVC sheathed power cable of 1.1 KV grade. 4 C x 6 sq mm copper Conductor armoured cable. quoted rates shall be including all taxes,duties,royalties,lead,lift,transpotation,GST etc complete.Nothing shall be payable separtely. Work shall be executed as per direction of engineer in charge,IISER Pune. Actual cable laid at site shall be measured for payments.

Supply of Following size of XLPE insulated and XLPE/PVC sheathed power cable of 1.1 KV grade. 4 C x 16 sq mm copper Conductor armoured cable. quoted rates shall be including all taxes,duties,royalties,lead,lift,transpotation,GST etc complete.Nothing shall be payable separtely. Work shall be executed as per direction of engineer in charge,IISER Pune. Actual cable laid at site shall be measured for payments.

Supply of Following size of XLPE insulated and XLPE/PVC sheathed power cable of 1.1 KV grade.3 1/2 C x 95 sq mm Aluminium Conductor armoured cable. quoted rates shall be including all taxes,duties,royalties,lead,lift,transpotation,GST etc complete.Nothing shall be payable separtely. Work shall be executed as per direction of engineer in charge,IISER Pune. Actual cable laid at site shall be measured for payments.

Supplying and fixing 30 A, 230 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A "C" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and making end termination with brass compression gland and copper lugs for following size of PVC insulated and PVC sheathed / XLPE copper conductor cable of 1.1 KV grade as required. 4 core x 16 sq.mm

Supplying and making end termination with brass compression gland and copper lugs for following size of PVC insulated and PVC sheathed / XLPE copper conductor cable of 1.1 KV grade as required. 6 core x 6 sq.mm

Supplying and making end termination with brass compression gland and copper lugs for following size of PVC insulated and PVC sheathed / XLPE copper conductor cable of 1.1 KV grade as required. 1 core x 16 sq.mm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 95 sq. mm (45mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 400 sq. mm (82mm)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. Upto 35 sq. mm (clamped with 1mm thick saddle)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. Upto 35 sq. mm (clamped with 1mm thick saddle)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)

Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Above 185 sq. mm and upto 400 sq. mm

Excavation for cable trenches of depth upto 1.2 m in soft soil including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50 metres.

Excavation for cable trenches of depth upto 1.2 m in soft soil including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50 metres.

Filling available excavated earth (excluding rock) in trenches, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 metres

Supplying and fixing cable route marker with 10 cm X 10 cm X 5mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required.

Supply and laying of 12 SWG GI wire along with aluminium armoured cable for earthing purpose. As complete.

Disconnection, removing, shifting and store of existing PVC trunking with its accessories, switch , sockets, cable and wires in store at campus with detailed inventory. During execution of work, materail should not be damaged and it can be reusable for electrical work. Required manpower, tools, transport etc will be scope of agency and nothing will be paid extra for the work. work should be carried out as instruction of engineer in charge, IISER Pune.

Disconnection, removing, shifting and reinstallation of 3 phase star delta starter with its accessories. During execution of work, materail should not be damaged and it can be reusable for electrical work. Required manpower, tools, transport etc will be scope of agency and nothing will be paid extra for the work. work should be carried out as instruction of engineer in charge, IISER Pune.

Disconnection, removing, shifting and store of existing DBs with its accessories, switch , sockets, cable and wires in store at campus with detailed inventory. During execution of work, materail should not be damaged and it can be reusable for electrical work. Required manpower, tools, transport etc will be scope of agency and nothing will be paid extra for the work. work should be carried out as instruction of engineer in charge, IISER Pune.

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Triple pole

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Triple pole and neutral

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)4 way (4 + 12), Double door

Supplying and fixing 30 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 A "C" curve, TPMCB, in sheet steel enclosure, onsurface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Supplying and fixing FP sheet steel enclosure on surface/ recess along with 16/25/32 A 415 V "C" curve FP MCB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 4 way (4 + 12), Double door

Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recessfor loop earthing as required.

Providing and fixing following rating and breaking capacity andpole MCCB with thermomagnetic release and terminalspreaders in existing cubicle panel board including drilling holesin cubicle panel, making connections, etc. as required. 125 A,36KA,FPMCCB

Supply & installation of surface mounted DLP U- PVC adaptable trunking raceways, fabricated out of U-PVC to Off-White or approved shade as per IS 733 of thickness 2.0mm for the base and sides with removable covers, complete with necessary bends, suitable sized junction boxes and tees etc, Complete. (For every 1mtr distance cable tag has to be provided for each circuit in the raceways - as more that 1C FRLS copper wire is required for 1 Circuit) PVC RACEWAYS ( Along the wall), DLP U- PVC adaptable trunking . Size: 105x 50mm PVC Raceways for Power & Data with above specifications

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 A switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.15/16 A switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 A socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6 pin 15/16 A socket outlet

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following Modular base & cover plate on existing modular metal / PVC boxes etc. as required.1/2 module

Supplying and fixing following Modular base & cover plate on existing modular metal / PVC boxes etc. as required.4 module

Supplying and fixing following Modular base & cover plate on existing modular metal / PVC boxes etc. as required.8 module

Supply and installation of surface PVC boxes for 4 module surface plate on suface/ recessed / ceiling / false ceiling as required as complete.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in with surface/ recessed medium class PVC conduit as required. ( For UPS Power) Colour code required for UPS power. 2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in with surface/ recessed medium class PVC conduit as required. ( For RAW Power) colour code required for RAW power 2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. 3 x 4 sq. mm ( for UPS power )

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. 3 x 4 sq. mm ( for RAW power )

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessedconduit as required.25 mm

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessedconduit as required.50 mm

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.1 run of cable

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.2 run of cable

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.3 run of cable

Supplying and installing following size of perforated painted with powder coating M.S. cable trays bends with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 150 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays bends with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 300 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 150 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 300 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays Tee with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 150 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays Tee with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 300 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays Cross Member with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.150 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays Cross Member with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.300 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays Reducer with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 150 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays Reducer with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 300 mm width X 50 mm depth X 1.6 mm thickness

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group A ( upto 3 meters )

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group B ( upto 4 meters )

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C ( upto 5 meters )

Supply and fixing of recess mounted 2'x2' - 36 W LED light fitting of based luminaire for surface mounting or recess mounting in False ceiling with 600 x 600 mm module, square luminaire complete with lamp and all accessories. Including the cost of all materials, labour, HOM of equivalent and machineries all lead lift, loading and unloading, transportation, if any other incidental charges at all level complete all as per specification & as directed by Engineer in charge. ( Make Syska / Wipro / Philips )

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonry duct / trench as required.Above 185 sq. mm and upto 400 sq. mm

Supply and making end termination for UTP 4 pair CAT 6 LAN cable with required IO modules and numbering ferrules which is suitable for existing patch panel and accessories ( At rack side ) as required.

Supply and making end termination for UTP 4 pair CAT 6 LAN cable with required IO modules and numbering ferrules which is suitable for existing modular type base , cover plates and accessories ( At field side ) as required.

Supply, installation, testing and commissioning of 42 U network rack, as per specifications given below: With cable manager, size 1000 x 1000 mm

Supply & installation of 24 port Jack fully loaded Patch Panel, make D link with required accessories as complete.

Supply and fixing of CAT 6 patch cord 2 m in length as required.

Supply and installation of splicing of OFC

Supply and laying of Single mode, 6 core fiber optical cable, as required.

Supply, installation, testing and commissioning of LIU SM full loaded with pigtails mounting etc

Supply and fixing of OFC patchcord LC-SC in exisitng panel

Testing for 100% cabling efficiency as per fluke test equipments (DTX / DSX Cable Analyzer or superior) and submitting the test reports in Original software formats and in PDF. The replacement of faulty cables /connectors those not supplied as a part of this project is not in the scope of work.

Supply of Following size of XLPE insulated and XLPE/PVC sheathed power cable of 1.1 KV grade.3 1/2 C x 16 sq mm Aluminium Conductor armoured cable. quoted rates shall be including all taxes,duties,royalties,lead,lift,transpotation,GST etc complete.Nothing shall be payable separtely. Work shall be executed as per direction of engineer in charge,IISER Pune. Actual cable laid at site shall be measured for payments.

Laying of additional 16 sqmm arm cable one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of direct in ground / trench / surface / duct / panle including requied accessoreis etc as required.

Supply, installation, testing and commissioning of relay box as per details given below : Supply, installation, testing and commissioning of replay box as per following specifications. Drawing, SLD, GA, BOM & specifications should be submitted to IISER Pune for approval before manufactureing of pane Supply, installation, testing and commissioning of 3 phase, 4 wire, 415 KV, 0.8 PF, 50 HZ panels. The fabrication shall be made with 14 SWG cold rolled sheet with M/C pressing, powder coated. The surface shall be rigorously treated for derusting in 7 tank process with dephosphating & paintingwith at least 2 coats of approved paint. The panel shall be totally enclosed metal clad type with double gasketting with rubber/ resin lining. The panel shall be having control directory pasted inside the panel. The panel shall be mounted on existing trench/ floor & shall have cable entry provision from the top & bottom with suitable alley as the case may be. The panel shall be tested for the same KA rating of the relevant highhest rating of MCCB. All comorents shall be from ISO-9001 companies and shall have relevant IS/IES approvals without fail. The panel shall be fully interlocked as required. The panel shall include baseframe channel support. ( The single line daigram shall be closely followed) 1. The panel shall be design as per norms of CEIG/ PWD/ CPWD/ Maharashtra State Electricity Distribution Company Ltd. 2. Panel includes 1 nos contactors 440 V coil 40 A capacity, connectors, buzzer, add on block 2NO+2NC, earthing terminals. 3. all aux supply, coil voltage, buzzer op voltage should be 400 V, 50 Hz 4. wall mounted design. 5. SP MCBs 3 nos 16 A each for each alarms. 6. All doors to have double rubber gasket with shutter assembly & door seating frame. 7. Ventilation vents for proper air ciculation. 8. The control wiring has to be in appropriate size with MCB protection. 9. All panels shall have top entry only. 10. LED indication lamp on front door ( 4 nos ), 3 nos for alarm status and 1 nos for power status. 11. Door earthings shall be provided for all doors. 12. Suitable for termination of upto 4 c x 16 sqmm sqmm cu arm cable for connectors 13.On delay timer with 01-300 sec with auto rest ,DIN mounted with 1 NO - 1 NC contact with 20 AMP, 230 v auxillary Quoted rates shall be including all taxes,duties,royalties,lead,lift,transpotation,GST etc complete.Nothing shall be payable separtely. Work shall be executed as per direction of engineer in charge,IISER Pune. Actual supply, installation and testing, commissiong of panel and all provision mentioned above at site shall be measured for payments.

Fabrication work in MS for cable enteries, laying, point wiring , DB istallation etc in MS , welding etc as complete.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Supply and laying of 70 sqmm copper flex PVC 1.1 KV grade green insulated cable on surface/ in existing trench/ on tray etc as required and complete.

Termination of 70 sqmm copper flex cable with requird copper lugs and nutbolts etc , as complete.

Supply installtion testing nad commissioning of Catalyst 2960-X 48 GigE PoE 370W, 2 x 10G SFP+ LAN Base ( Product serial no 0 WS-C2960X-48LPD-L )

Supply installtion testing nad commissioning of( CAB-CONSOLE-RJ45 ) Console Cable 6ft with RJ45 and DB9F

Supply installtion testing nad commissioning of (C2960X-STACK) Catalyst 2960-X FlexStack Plus Stacking Module

Supply installtion testing nad commissioning of1.0.1 CON-SNT-WSC48LPD SNTC-8X5XNBD Catalyst 2960-X 48 G 1 Nos 28000.00 28000.00

Supply installtion testing nad commissioning of2.0.1 CON-SNT-WSC604DL SNTC-8X5XNBD Catalyst 2960-X 24 G

HVAC WORKS

Outdoor Units (Make:- Toshiba/Daikin/Mitsubishi )

Supply installation testing and commissioning of Air Cooled Top Discharge Variable Refrigerant Flow Modular or Single Outdoor Unit. The Outdoor Unit should have 100% inverter multiple compressors. The outdoor unit must have with necessary accessories for oil separation and should operate with equal runtime for all Compressor/Inverter or On/Off type. Air Cooled condenser coils and fins must have standard anticorrosive treatment. Outdoor Unit should have Refrigerant circuit, Oil Balancing / Equalizing circuit, High Pressure Switch, Condenser Fan motor over load Protector, Over current relay, Inverter over load Protector, Electronic expansion valve, the units should have ELCB arrangements & etc The refrigerant should be CFC Free R 410a only.The outdoor unit discharge air line should be covered with G.I ducting as per direction of Engineer Incharge. and the outdoor panel must be 100% compatible with BMS. The unit/s must also be provided with self addressable control system for control of indoor & other outdoor machines. The quoted rates shall be inclusive of all taxes and levis, duties, lead, lift,transpotation, placing, scaffolding, core cutting of required diameter in walls, finishing and minor civil works and nothing shall be paid separately. 30 HP Full Inverter Top Discharge

Supply installation testing and commissioning of Air Cooled Top Discharge Variable Refrigerant Flow Modular or Single Outdoor Unit. The Outdoor Unit should have 100% inverter multiple compressors. The outdoor unit must have with necessary accessories for oil separation and should operate with equal runtime for all Compressor/Inverter or On/Off type. Air Cooled condenser coils and fins must have standard anticorrosive treatment. Outdoor Unit should have Refrigerant circuit, Oil Balancing / Equalizing circuit, High Pressure Switch, Condenser Fan motor over load Protector, Over current relay, Inverter over load Protector, Electronic expansion valve, the units should have ELCB arrangements & etc The refrigerant should be CFC Free R 410a only.The outdoor unit discharge air line should be covered with G.I ducting as per direction of Engineer Incharge. and the outdoor panel must be 100% compatible with BMS. The unit/s must also be provided with self addressable control system for control of indoor & other outdoor machines. The quoted rates shall be inclusive of all taxes and levis, duties, lead, lift,transpotation, placing, scaffolding, core cutting of required diameter in walls, finishing and minor civil works and nothing shall be paid separately. 22 HP Full Inverter Top Discharge

Indoor Units: Supply installation testing and commissioning of 4 way Cassette Unit comprising of Air filter, Two/Three level fan Speed motor, DX - cooling coil, Drain pan, Inbuilt Pump, Washable Grill, Auto - swing Louvers, . The machine cost should include cost for cordless remote for controlling the temperature and ON/OFF siwtch and panel.The quoted rates shall be inclusive of all taxes and levis, duties, lead, lift,transpotation, placing, scaffolding, core cutting of required diameter in walls, finishing and minor civil works and nothing shall be paid separately. 1.5 TR

Indoor Units: Supply installation testing and commissioning of 4 way Cassette Unit comprising of Air filter, Two/Three level fan Speed motor, DX - cooling coil, Drain pan, Inbuilt Pump, Washable Grill, Auto - swing Louvers, . The machine cost should include cost for cordless remote for controlling the temperature and ON/OFF siwtch and panel.The quoted rates shall be inclusive of all taxes and levis, duties, lead, lift,transpotation, placing, scaffolding, core cutting of required diameter in walls, finishing and minor civil works and nothing shall be paid separately. 2.0 TR

Indoor Units: Supply installation testing and commissioning of 4 way Cassette Unit comprising of Air filter, Two/Three level fan Speed motor, DX - cooling coil, Drain pan, Inbuilt Pump, Washable Grill, Auto - swing Louvers, . The machine cost should include cost for cordless remote for controlling the temperature and ON/OFF siwtch and panel.The quoted rates shall be inclusive of all taxes and levis, duties, lead, lift,transpotation, placing, scaffolding, core cutting of required diameter in walls, finishing and minor civil works and nothing shall be paid separately. 3.0 TR

Supply installation testing and commissioning of Indoor Refrigerant Y-Joints with insulation of suitable sizes.The quoted rates shall be inclusive of all taxes and levis, duties, lead, lift,transpotation, placing, scaffolding, core cutting of required diameter in walls, finishing and minor civil works and nothing shall be paid separately.

Refrigerant piping Supply, installation, testing and commissioning of refrigerant Suction & liquid piping using eddy current free Copper pipes and fittings like elbows, couplers, tee joints, brass fittings, "U" loops, expansion loops etc. Supports consisting of GI box / "C" sections & female anchor fasteners with full threaded GI rods, insulation of pipes using 13 mm thick elastomeric closed cell Nitrile Rubber insulation material having class "O" for fire properties, structural clamps with hard PVC pipe sleeves under the clamps to protect insulation at supports, tagging to enable tracing connectivity to respective units as per shop drawings to be generated by contractor and approved by consultant. Submission of test reports in approved format forms a part of this item scope. Making up of any leakages occuring during testing / commissioning / first calender year from handing over, including supply, labour, consumables, refrigerant, top up, oil top up and incidental expenses also forms a part of the scope covered under this item.34.9 Ø mm-semi hard pipe (1.21 mm thick) with 19 mm thick insulation

Supply, installation, testing and commissioning of refrigerant Suction & liquid piping using eddy current free Copper pipes and fittings like elbows, couplers, tee joints, brass fittings, "U" loops, expansion loops etc. Supports consisting of GI box / "C" sections & female anchor fasteners with full threaded GI rods, insulation of pipes using 13 mm thick elastomeric closed cell Nitrile Rubber insulation material having class "O" for fire properties, structural clamps with hard PVC pipe sleeves under the clamps to protect insulation at supports, tagging to enable tracing connectivity to respective units as per shop drawings to be generated by contractor and approved by consultant. Submission of test reports in approved format forms a part of this item scope. Making up of any leakages occuring during testing / commissioning / first calender year from handing over, including supply, labour, consumables, refrigerant, top up, oil top up and incidental expenses also forms a part of the scope covered under this item.28.6 Ø mm-semi hard pipe (1.00 mm thick) with 19 mm thick insulation

Supply, installation, testing and commissioning of refrigerant Suction & liquid piping using eddy current free Copper pipes and fittings like elbows, couplers, tee joints, brass fittings, "U" loops, expansion loops etc. Supports consisting of GI box / "C" sections & female anchor fasteners with full threaded GI rods, insulation of pipes using 13 mm thick elastomeric closed cell Nitrile Rubber insulation material having class "O" for fire properties, structural clamps with hard PVC pipe sleeves under the clamps to protect insulation at supports, tagging to enable tracing connectivity to respective units as per shop drawings to be generated by contractor and approved by consultant. Submission of test reports in approved format forms a part of this item scope. Making up of any leakages occuring during testing / commissioning / first calender year from handing over, including supply, labour, consumables, refrigerant, top up, oil top up and incidental expenses also forms a part of the scope covered under this item.22.3 Ø mm-semi hard pipe (0.8 mm thick) with 13 mm thick insulation

Supply, installation, testing and commissioning of refrigerant Suction & liquid piping using eddy current free Copper pipes and fittings like elbows, couplers, tee joints, brass fittings, "U" loops, expansion loops etc. Supports consisting of GI box / "C" sections & female anchor fasteners with full threaded GI rods, insulation of pipes using 13 mm thick elastomeric closed cell Nitrile Rubber insulation material having class "O" for fire properties, structural clamps with hard PVC pipe sleeves under the clamps to protect insulation at supports, tagging to enable tracing connectivity to respective units as per shop drawings to be generated by contractor and approved by consultant. Submission of test reports in approved format forms a part of this item scope. Making up of any leakages occuring during testing / commissioning / first calender year from handing over, including supply, labour, consumables, refrigerant, top up, oil top up and incidental expenses also forms a part of the scope covered under this item.19.1 Ø mm-semi hard pipe (0.80 mm thick) with 13 mm thick insulation

Supply, installation, testing and commissioning of refrigerant Suction & liquid piping using eddy current free Copper pipes and fittings like elbows, couplers, tee joints, brass fittings, "U" loops, expansion loops etc. Supports consisting of GI box / "C" sections & female anchor fasteners with full threaded GI rods, insulation of pipes using 13 mm thick elastomeric closed cell Nitrile Rubber insulation material having class "O" for fire properties, structural clamps with hard PVC pipe sleeves under the clamps to protect insulation at supports, tagging to enable tracing connectivity to respective units as per shop drawings to be generated by contractor and approved by consultant. Submission of test reports in approved format forms a part of this item scope. Making up of any leakages occuring during testing / commissioning / first calender year from handing over, including supply, labour, consumables, refrigerant, top up, oil top up and incidental expenses also forms a part of the scope covered under this item.15.9 Ø mm-soft pipe (0.80 mm thick) with 13 mm thick insulation

Supply, installation, testing and commissioning of refrigerant Suction & liquid piping using eddy current free Copper pipes and fittings like elbows, couplers, tee joints, brass fittings, "U" loops, expansion loops etc. Supports consisting of GI box / "C" sections & female anchor fasteners with full threaded GI rods, insulation of pipes using 13 mm thick elastomeric closed cell Nitrile Rubber insulation material having class "O" for fire properties, structural clamps with hard PVC pipe sleeves under the clamps to protect insulation at supports, tagging to enable tracing connectivity to respective units as per shop drawings to be generated by contractor and approved by consultant. Submission of test reports in approved format forms a part of this item scope. Making up of any leakages occuring during testing / commissioning / first calender year from handing over, including supply, labour, consumables, refrigerant, top up, oil top up and incidental expenses also forms a part of the scope covered under this item.12.7 Ø mm-soft pipe (0.80 mm thick) with 13 mm thick insulation

Supply, installation, testing and commissioning of refrigerant Suction & liquid piping using eddy current free Copper pipes and fittings like elbows, couplers, tee joints, brass fittings, "U" loops, expansion loops etc. Supports consisting of GI box / "C" sections & female anchor fasteners with full threaded GI rods, insulation of pipes using 13 mm thick elastomeric closed cell Nitrile Rubber insulation material having class "O" for fire properties, structural clamps with hard PVC pipe sleeves under the clamps to protect insulation at supports, tagging to enable tracing connectivity to respective units as per shop drawings to be generated by contractor and approved by consultant. Submission of test reports in approved format forms a part of this item scope. Making up of any leakages occuring during testing / commissioning / first calender year from handing over, including supply, labour, consumables, refrigerant, top up, oil top up and incidental expenses also forms a part of the scope covered under this item.9.52 Ø mm-soft pipe (0.80 mm thick) with 13 mm thick insulation

Supply, installation, testing and commissioning of refrigerant Suction & liquid piping using eddy current free Copper pipes and fittings like elbows, couplers, tee joints, brass fittings, "U" loops, expansion loops etc. Supports consisting of GI box / "C" sections & female anchor fasteners with full threaded GI rods, insulation of pipes using 13 mm thick elastomeric closed cell Nitrile Rubber insulation material having class "O" for fire properties, structural clamps with hard PVC pipe sleeves under the clamps to protect insulation at supports, tagging to enable tracing connectivity to respective units as per shop drawings to be generated by contractor and approved by consultant. Submission of test reports in approved format forms a part of this item scope. Making up of any leakages occuring during testing / commissioning / first calender year from handing over, including supply, labour, consumables, refrigerant, top up, oil top up and incidental expenses also forms a part of the scope covered under this item.6.4 Ø mm-soft pipe (0.80 mm thick) with 13 mm thick insulation

Supplying & fixing of copper refrigerant piping with minimum 9 mm insulation complete from indoor unit to outdoor unit with supports Etc. of suitable size.

Supply installation testing and commissioning of corded remote controllers for cassette units

Drain Piping PVC hard pipe of below sizes having minimum 3 mm wall thickness, insulated with 9 mm thick cross linked Polyethylene tube sections laminated with aluminium foil , joints to be sealed with solvent based adhesive & 2" aluminium adhesive tape 32mm with 9 mm thick insulation

Drain Piping PVC hard pipe of below sizes having minimum 3 mm wall thickness, insulated with 9 mm thick cross linked Polyethylene tube sections laminated with aluminium foil , joints to be sealed with solvent based adhesive & 2" aluminium adhesive tape 25mm with 9 mm thick insulation

Drain Piping PVC hard pipe of below sizes having minimum 3 mm wall thickness, insulated with 9 mm thick cross linked Polyethylene tube sections laminated with aluminium foil , joints to be sealed with solvent based adhesive & 2" aluminium adhesive tape 20mm with 9 mm thick insulation

Supply installation testing and commissioning of centralized remote controller to control up to 64 indoor units. It should have provision to control and monitor the AC System through web access anywhere with computer complete as per manufacturer specifications & as per directions of Engineer in charge. The quoted rates shall be inclusive of all taxes and levis, duties, lead, lift,transpotation, placing, scaffolding, core cutting of required diameter in walls, finishing and minor civil works and nothing shall be paid separately.

Supply of 2.0 TR capacity Hiwall type indoor unit with minimum 4 star rating with cordless remote control & outdoor unit mounted with suitable metal stand with R410 or equivalent green refrigerant gas only. The quoted rates shall be inclusive of all taxes and levis, duties, lead, lift,transpotation, placing, scaffolding, core cutting of required diameter in walls, finishing and minor civil works and nothing shall be paid separately. (Make : Toshiba / Mitsubishi / Daikin)

Power/Electrical Cabling : Supply and laying of Control Cabling with copper conductor shielded copper cable FR / FRLS of approved make with end termination for indoor units (from indoor to outdoor unit & interconnecting control cabling & for CRC remote control from indoor to indoor to CRC controller). The cable should pass through hard PVC conduit. The cost of conduit should be included in cable cost.The quoted rates shall be inclusive of all taxes and levis, duties, lead, lift,transpotation, placing, scaffolding, core cutting of required diameter in walls, finishing and minor civil works and nothing shall be paid separately. 2core*1.5 sq mm

Supply and laying of copper conductor cabling with 3-pin top & flexible conduit to connect IDU power supply including cable terminations like lugs, glands etc. Cables & accessories to be ISI marked. Average 2 m long.The quoted rates shall be inclusive of all taxes and levis, duties, lead, lift,transpotation, placing, scaffolding, core cutting of required diameter in walls, finishing and minor civil works and nothing shall be paid separately1.5 Sq mm x 3 Core.

Supply and laying of copper conductor cabling with 3-pin top & flexible conduit to connect IDU power supply including cable terminations like lugs, glands etc. Cables & accessories to be ISI marked. Average 2 m long.The quoted rates shall be inclusive of all taxes and levis, duties, lead, lift,transpotation, placing, scaffolding, core cutting of required diameter in walls, finishing and minor civil works and nothing shall be paid separately2.5 Sq mm x 3 Core.

Supplying and laying of complete cable work with glands, lugs and terminations, using XLPE insulated PVC sheathed steel tape/wire armoured underground copper conductor cables of following sizes for electric supply from main HVAC panel to various loads including interconnections from starters to VRF outdoor on suitable cable trays/supports as requried including connections on both sides as per specificaitons as required.The quoted rates shall be inclusive of all taxes and levis, duties, lead, lift,transpotation, placing, scaffolding, core cutting of required diameter in walls, finishing and minor civil works and nothing shall be paid separately.6.0 Sq mm X 4 core

Supplying and laying of complete cable work with glands, lugs and terminations, using XLPE insulated PVC sheathed steel tape/wire armoured underground copper conductor cables of following sizes for electric supply from main HVAC panel to various loads including interconnections from starters to VRF outdoor on suitable cable trays/supports as requried including connections on both sides as per specificaitons as required.The quoted rates shall be inclusive of all taxes and levis, duties, lead, lift,transpotation, placing, scaffolding, core cutting of required diameter in walls, finishing and minor civil works and nothing shall be paid separately.10.0 Sq mm X 4 core

Supply and charging of additional refrigerant gas (R - 410a) for the entire length of refrigerant piping and system.The quoted rates shall be inclusive of all taxes and levis, duties, lead, lift,transpotation, placing, scaffolding, core cutting of required diameter in walls, finishing and minor civil works and nothing shall be paid separately.

Providng and fixing M.S Table top Stand suitable size of Angle Frame (min. -50*50*5mm) complete with 2 coats of Epoxy Red Oxide paint and 2 coats of Black Oil Enamel paint. Fabrication drawings to be approved by IISER prior to the execution. Foundation and Civil Works if required will also be in contractor Scope.The quoted rates shall be inclusive of all taxes and levis, duties, lead, lift,transpotation, placing, scaffolding, core cutting of required diameter in walls, finishing and minor civil works and nothing shall be paid separately.

Fume Hood work,Dismantling, shifting & Reinstallation 300mm dia - PPGL + FRP ducting including Resin., GI Nut bolts, gasket Threaded Rod,Clamps, FRP Joints Etc.

Fume Hood work,Dismantling of blowers (Capacity below 7.5Kw) with blower mounting frame, supports & Etc.and shifting to rearby store room (within campus-around 600 meters away).

Fume Hood work: Re installation of dismantled Blower (Capacity below 7.5Kw) with blower mounting frame, supports & Etc.

Fume Hood work:Dismantling of fume hoods and shifting to near by store room (within campus-around 600 meters away).

Fume Hood work: Reinstallation of dismantled fume hood. It inslude Shifting from store to site, all tools , tackes, spare etc.includubf all as complete job , nothing extra shall be paid

Fume Hood work: Supply of PPGL + FRP ducting & Fitting.

Fume Hood work :Installation of PPGL + FRP ducting & Fitting.

Fume Hood work: Supply of 300mm dia 90˚bend.

Fume Hood work : Installation of 300mm dia 90˚bend. It include as all , spare tools tackles, ladder, etc complete job. Nothing extra shall be paid

Fume Hood work: Dismantling & Reinstallation of Spot Extractor (Elephant Trunk) including Nut & bolts, gasket Threaded Rod, Clamps, FRP Joints Etc.as complete job. Nothing extra shall be paid.

Fume Hood work : Supply and installation of M.S. stand for walkway. The stand should be made of MS L-Angel of size 50*50*4 mm thick. The cost includes welding & minor civil works etc as complete Job. Nothing extra shall be paid.

Fume Hood work : Supply and laying of Power and control cabling work with glands and terminations, using XLPE insulated PVC sheathed steel tape/wire armoured aluminium conductor cables of following sizes for electric supply from HVAC panel to various loads including interconnections from starters to motors on suitable cable trays/supports as required including double compression gland connections on both sides as per specifications as required. 4Core*6 Sq mm