Directorate Of Construction Services And Estate Management Tender

PANELS

Design,manufacture,supply,Installation,Testing and Commissioning of Main LT panel with following at Gorund floor as per tender specifications: 630A MCCB FP Incommer-1no. 630A,4P, Copper TPN busbars Outgoing feeders: 200A TPN MCCB - 7nos, 315A TPN MCCB - 1nos, 125A TPN MCCB - 3nos, 630A TPN MCCB type Isolator - 1nos tie feeder KWH meter class 1.0 similar to EM6433H of M/s Schneider with RS485 port-1 no.

Design,manufacture,supply,Installation,Testing and Commissioning of Emergency LT panel at Ground Floor as per tender specifications Emergency panel with 250 FP Auto transfer switch 250A FP MCCB incomer 250A copper TPN busbar Outgoing feeders:100A TPN MCCB- 2nos, 63A TPN MCCB-4nos, 32A MCCB-6nos KWH meter class 1.0 similar to EM6433H of M/s Schneider with RS485 port-1 no.

Design,manufacture,supply,Installation,Testing and Commissioning of Suitable automatic star/delta starter with fuse backup protection (Type-II co-ordinated as per IS 13947-4-1) for 40HP domestic water pump with overload protection, current sensing type single phase preventor complete with all accessories and internal wiring required for manual operation, etc. complete as required. The scope also includes providing following: 1) 1 no.0-63 A , 96 sqmm ammeter with three way & off selector switch - 1 set 2) 3 nos 60/5 A ratio,class-I 5 VA burden cast resin current transformer for current monitoring. - 1 set 3) On-OFF indication lamp - 1 set 4) ON-OFF push button - 1 set 5) The auto manual selector switch - 1 set

Distribution Boards

Shaft VTPN DB: Supply, installation, testing & commissioning of readymade,IP43, VTPN MCCB DB,Powder coated, double door type consisting of following components all as required,fixing on wall with suitable brackets made up 40 X5 mm MS flat including painting with one coat of red oxide and two coats of enamel paint & instructed by the Engineer-in-charge. i) 160A 4P MCCB - 1 no. ii)40/63A,3P,10kA,C-curve,MCB - 8 each. ii)Wire way box of same make,Din channel, tinned copper bus bar, earthing and neutral links etc.---1 set

ETPN DB for each floor lighting & cubical: Supply, installation, testing & commissioning of readymade,IP43,PPI,ETPN MCB DB,Powder coated, double door type consisting of following components all as required,fixing on wall with suitable with suitable brackets made up 40 X5 mm MS flat including painting with one coat of red oxide and two coats of enamel paint & instructed by the Engineer-in-charge. i) 32A,10kA,C-Curve,4P MCB--- 1 no. ii)32A ,RCCB, DP 30mA sensitivity, HPI - 3 nos. iii)6/10/16/25/32A, 10kA,C-Curve, SP, MCB - 18 nos. iii)Wire way box of same make. --- 01 set iv)Din channel, tinned copper busbars,earthing and neutral links, PPI kit, etc.---1 set

ETPN DB for each floor (Power DB, AC DB): Supply, installation, testing & commissioning of readymade,IP43, ETPN MCB DB,Powder coated, double door type consisting of following components all as required,fixing on wallwith suitable brackets made up 40 X5 mm MS flat including painting with one coat of red oxide and two coats of enamel paint & instructed by the Engineer-in-charge. i) 63A,10kA,C-Curve,4P MCB--- 1 no. ii)63A ,RCCB, DP 30mA sensitivity, HPI - 3 nos. iii)6/10/16/25/32A, 10kA,C-Curve, SP, MCB - 30 nos. iii)Wire way box of same make. --- 01 set iv)Din channel, tinned copper busbars,earthing and neutral links, PPI kit, etc.---1 set

ETPN DB for each floor Computer DB Supply, installation, testing & commissioning of readymade,IP43, ETPN MCB DB,Powder coated, double door type consisting of following components all as required,fixing on wallwith suitable brackets made up 40 X5 mm MS flat including painting with one coat of red oxide and two coats of enamel paint & instructed by the Engineer-in-charge. i) 63A,10kA,C-Curve,4P MCB--- 1 no. ii) 63A, 12KA, 4P SPD----1 no ii)63A ,RCCB, DP 30mA sensitivity, HPI - 3 nos. iii)6/10/16/25/32A, 10kA,C-Curve, SP, MCB - 30 nos. iii)Wire way box of same make. --- 01 set iv)Din channel, tinned copper busbars,earthing and neutral links, PPI kit, etc.---1 set

Emergency DB : Supply, installation, testing & commissioning of readymade,IP43, 12ways, SPN MCB DB,Powder coated, double door type consisting of following components all as required,fixing on wallwith suitable brackets made up 40 X5 mm MS flat including painting with one coat of red oxide and two coats of enamel paint & instructed by the Engineer-in-charge. i) 40A,10kA,C-Curve,2P RCBO--- 1 no. ii)6/10/16/25/32A, 10kA,C-Curve, SP, MCB - 08 nos. iii)Wire way box of same make. --- 01 set iv)Din channel, tinned copper busbars,earthing and neutral links, etc.---1 set

Disconnection and Removal of existing DBs (approx 26 nos) and taking away the scrap material as per instruction of Engineer in charge.

Point wiring: Providing point wiring for light / ceiling fan / 6/16A socket outlet/AC point etc. with 1100V grade, FRLS PVC insulated multi stranded copper wires in existing concealed & surface conduit/ existing PVC casing capping on surface, controlling modular switches with on existing surface switch boards with required bakelite sheets//ready made fire retardant palstic boxes/readymade concealed GI switch boxes with cover plate & metal frame, angle / batten pendent lamp holders ,PVC round plates, 6A connectors in concealed junction boxes , ferrule numbers on both sides, 1.1kV grade FRLS PVC insulated copper conductor wires for earthing of above said specifications, labelling etc. all as per site conditions, specifications, drawings and as instructed by Engineer-in-charge. Scope of work shall also includes providing the tags for wires inside casing & capping for bunching to avoid hanging of wires at the intervals of 600mm. Note: 1. Wiring layout arrangement and samples of switch boxes are to be got approved prior to procurement. 2. All switches, sockets, cover plates & frame, plastic surface boxes, etc. shall be of white colour & and other accessories like lamp holders, ceiling roses & doorbell etc. shall be of polycarbonate body and shall preferably ISI marked. 3. The dimensions of switches, sockets, and fan regulators shall preferably be ISI mark. 4. HMS PVC sleeves will have to be provided for crossing the wall, drilling holes & it’s refinishing to be also included in the scope. 5.The scope of work also includes removing of existing MS switch boards by breaking the brick wall, making suitable cut-outs in brick wall for fixing new switch boards, finishing with cement mortar, applying white putty as required, providing proper finish to wall,touchup paitnting for that area with OBD paint of existing shade and as per instructions of E-I-C. 6. All metalic boxes/switch boxes shall be earthed with 1.1kV grade FRLS PVC insulated 1.5sq.mm copper flexible wire. 7.Point wiring also includes supply and install of conduits from new DB/ new load point with slight change in location in shaft/ in user rooms. 8. Disconnection,dismantling of existing point wiring,switch boards,junction boxes etc. and taking away the dismantled wires,switch boards,etc. suitable rebate for taking of dismantled material shall be included in the quoted rates. 9. PVC casing capping for all point wiring items shall be measured separately under item no 5.

Primary light point with 1.5 sq.mm wires complete with 6A, SP, 240V controlling switch

Secondary Light point with 1.5 sq.mm wires looped to item no 4.1

6 A socket outlet point with 1.5 sq.mm wires along with complete with 6A, SP, 240V controlling switch and 6A, 5 pin socket outlet.

Ceiling fan point with 1.5 sq.mm wires complete with 6A, SP, 240V switch (1-module).

6/16 A + 6A ( in six module box)socket outlet point with 2.5 sq.mm wires 2 nos. & 1.5 sq.mm wires 1 no.complete with 16A, SP, 240V controlling switch and 16A, 5 pin socket outlet, 6A, SP, 240V controlling switch and 6A, 5 pin socket outlet.

Air conditioner point with 4.0 sq.mm wires 2 nos. and 2.5 sq mm wire 1 no., complete with 4 module metal plug & socket with 20A, DP MCB, 240V .

Primary Computer point ( in twelve module box) socket outlet point with 2.5 sq.mm wires 2 nos. & 1.5 sq.mm wires 1 no.complete with 4nos. 6A, SP, 240V controlling switch and 4nos. 6A, 5 pin socket outlet.

Secondary Computer point ( in twelve module box) socket outlet point with 2.5 sq.mm wires 2 nos. & 1.5 sq.mm wires 1 no.complete with 4nos. 6A, SP, 240V controlling switch and 4nos. 6A, 5 pin socket outlet. Looped to above item no 4.7.

PVC Casing capping/Trunking:- Supply & installation of following size white / ivory PVC casing capping/Trunking with flexible cover, on surface of slab / wall / column fixed with nylon rawal plug, GI wood screws at intervals of 300mm complete with all accessories like plastic junction boxes if required etc.

25 mm x 16 mm

50mm x 50 mmm

80mm x 50 mm

100mm x 100 mm

LAN System Supply, installation, testing &commissioning of local area network system comprising of passive components like CAT-6A UTP or improved data cable, information outlet with RJ-45 connections , enclosures for data outlets with face plates, patch panels, cable managers, 19" mounting racks , power panels in racks , cooling fans in racks, flexible G.I pipe, complete with labelling/identification on the cable , outlets, patch panels etc. including certification complete in all respect as required as per standards, drawings, specifications and instructions of Engineer- in -Charge. Note : 1. LAN work shall be done by a specialised agency in the field. 2. Active components i.e. switches are not in the scope of the agency and shall be executed by the users separately. Agency shall extend full co-operation to the agency / users executing the balance work which is not in the scope of this tender. 3. Scope includes termination of cables at both ends with all accessories and installation/mounting of 19" racks with all accessories like angle iron frame work etc. without any extra cost to the Department. 4. All LAN passive components shall be of same make.

Lan I/O Point : Point wiring CAT-6A UTP in existing PVC casing capping on slab/column/beam/wall wherever required complete with all accessories with RJ-45 shuttered socket outlets (modular) surface on wall/column with all accessories including label holder, face plate, box, screws etc. terminated at one end at patch panel at the other end in outlet with an extra loop length of approx. 2 m at patch panel, ferrule numbers on both side, all terminations as per standards, drawing, specifications and as per enclosed detailed specifications & as per instructions of the E-I-C. Note : 1. Patch panel shall be measured separately. 2. Colour of the outlet and facia plate shall be matching with electrical switches and sockets with the approval of E-I-C.

Patch Panels: Supply, installation , testing & commission of 24 port, 19" rackmountable patch panel equipped with RJ-45 receptive female, CAT-6A UTP connectors and cable managers complete as required as per enclosed detailed specifications & as per instructions of the E-I-C.

Supply, installation, testing & commissioning of 19" wall mounted double section racks of minimum 15 U height, 600 mm deep with toughned glass door with following accessories : a) Cooling fan position tray with fans (230 V AC) - 1 no b) Horizontal mounting AC power panel with minimum 2 nos. 6/16 A 3 pin sockets with minimum 2 nos. 6/16 A 3 pin sockets with switches, 3 core 4 sq mm copper conductor cable cord(5m) and 32 A MCB-1 panel. c) Mounting accessories eg cage nuts, screws, supporting angles etc for switch , patch cord panels, fan tray, LIU ,full cable entry plate with brush at top & bottom etc. d) Blanking plates : 2U-1 no, 1U-2 nos e) Horizontal cable manager - 3 nos.

24 core fibre optic cable fixed on wall/column/slab/ shaft on 3-4mm thick G.I. spacer , 2mm. thick G.I. fabricated saddle, all fixing accessories, etc. pas per enclosed detailed specifications & as per instructions of the E-I-C.

Supply and Installation of 24 port, duplex, fully loaded with LC adapters and pig tails, spool and splice trays, 19" rack mountable, LIU suitable fo single mode OFC as per enclosed detailed specifications & as per instructions of the E-I-C.

Cat-6A Patch cords of 3M length as per enclosed detailed specifications & as per instructions of the E-I-C.

Supply and installation of single mode LC-LC, duplex OFC patch cords of 3m length pas per enclosed detailed specifications & as per instructions of the E-I-C.

Fusion splicing Termination of optical fibre cable using fusion termination method, testing & commissioning with alll accessories all as per enclosed detailed specifications & as per instructions of the E-I-C.

Telephone system:

Telephone Point Wiring : Point wiring with 4 pair CAT-6A UTP wires copper conductor PVC insulated, in existing white/ivory PVC casing capping on slab/column/beam/wall complete with all accessories, RJ-11 telephone socket outlets with shutter ferrule numbers on both side of the circuits all terminations with ferrule /lugs if required, labelling all as per drawing specifications & as per instructions of E-I-C. NOTE: 1. Point wiring means 4 pair CAT-6 wires from Telephone Tag Block to assigned point including end termination of one pair at both sides and other pairs should be kept spare.

Telephone Tag Block (TTB) :Supply, installation, testing & commissioning of following readymade Krone connector telephone tag block box, 18 SWG MS CRCA sheet, concealed/surface mounted on MS frame of size 40 x 40 x 5mm and grouted on the wall/fixed on the column free standing type with anchor fasterners, cable end/wire way box,if required, with adequate space facility to be provided in the TTB, with front operable hinged door, neoprene rubber/cork gasket for joints, wire bunching clamps , name plate etc. all as per standards, specification, drawing & instructions of E.I.C. Note:1) Point distribution diagram shall put in side the DB with polythene protective cover. 2) All fabrication drawings shall be got approved.

200 pair telephone tag box : A set consisting of 1)Disconnection module 2 /10 -- 20 nos. 2)Back mounting frame - 2/11 --20 nos (C.T. box with mounting bracket ) 3) Transparent dust cover -- 1 no. complete with all accessories 4) Label Holder - 1 no

100 pair telephone tag box : A set consisting of 1)Disconnection module 2 /10 -- 10 nos. 2)Back mounting frame - 2/11 --10 nos (C.T. box with mounting bracket ) 3) Transparent dust cover -- 1 no. complete with all accessories 4) Label Holder - 1 no

50 pair telephone tag box : A set consisting of 1)Disconnection module 2 /10 -- 5 nos. 2)Back mounting frame - 2/11 --5 nos (C.T. box with mounting bracket ) 3) Transparent dust cover -- 1 no. complete with all accessories 4) Label Holder - 1 no

Supply, installation, testing & commissioning of jelly filled telephone cable with copper conductor, PE insulated, cores twisted, G.I. wire/strip armoured, PVC sheathed cable fixed on wall/ column / slab on 5mm. thick GI spacer/MS flat support fixed with wood screws with 20 SWG GI saddle etc all fixing accessories and as directed by E-I-C.

0.5 mm dia 200 pair Telephone cable

0.5 mm dia 100 pair Telephone cable

0.5 mm dia 50 pair Telephone cable

End jointing of Telephone cable with all jointing materials like cable gland/GI threaded nipple with checknut raychem heat shirnkable sleeve of appropriate size ferrule lugs, ferrule numbers, wire dressing clamps/button tapes, etc. complete including all jointing materials and with necessary special tool kit for KRONE type connector and as directed by E-I-C.

0.5 mm dia 200 pair Telephone cable

0.5 mm dia 100 pair Telephone cable

0.5 mm dia 50 pair Telephone cable

Supply, installation, testing & commissioning of 1.1 KV copper multi stranded conductor with XLPE insulation, extruded PVC inner sheathed, G.I flat steel strip armoured, extruded PVC outer sheathed cable conforming to IS 7098 Part-I with latest amendments, fixed on wall/column/slab/ shaft on 5mm thick G.I. flat/angle support fixed with coach screws/grouted in wall/anchor fasteners, 2mm. thick G.I. fabricated saddle, all fixing accessories, etc. providing brass cable number tag as per enclosed detailed specifications & as per instructions of the E-I-C & of the following sizes.

4C x 6 sq.mm Cu conductor Arm. Cable

4C x 10 sq.mm Cu conductor Arm. Cable

4Cx16 Sqmm Cu conductor Arm. Cable

4C X 25sq.mm Cu conductor Arm. Cable

3.5Cx50 Sqmm Al conductor Arm. Cable

3.5Cx70 Sqmm Al conductor Arm. Cable

End termination : Providing end termination of following sizes of MV PVC/XLPE insulated armoured cables with solder less heavy duty tinned copper tube terminals(lugs), brass cable gland, insulation tape, duplicate earthing for cable gland with suitable sizes of copper clamps inter connecting nearest earthing point with 8SWG copper wires etc. as per relevant IS specification and as per instruction of Engineer in-charge.

4C x 6 sq.mm Cu conductor Arm. Cable

4C x 10 sq.mm Cu conductor Arm. Cable

4Cx16 Sqmm cu conductor Arm. Cable

4C x 25sq.mm Cu conductor Arm. Cable

3.5C x50 Sqmm Al conductor Arm. Cable

3.5Cx70 Sqmm Al conductor Arm. Cable

3.5Cx120 Sqmm Al conductor Arm. Cable

3.5Cx300 Sqmm Al conductor Arm. Cable

Disconnection & retermination of 3.5Cx300 Sqmm Al conductor Arm. Cable with Solder less heavy duty tinned copper tube terminals(lugs)Lugs shall be included in scope of this item & as per instruction of Engineer in-charge.

Earth Station: Providing earth station with heavy dipped GI earth plates electrode 600 x 600 x 6.0 mm in size at the depth minimum of 2.5 m below ground level (bottom of Plate) confirming to IS 3043 complete with all required materials like coke / charcoal, salt, G.I nut bolts, washers, 19 mm dia GI pipe (B class), 150 mm thick concrete wall chamber duly plastered having size of 500 x 500 x 500 mm, heavy duty (minimum 6 mm thick) M.S chequered plate cover, associated materials like 40 x 40 x 5 mm angle iron frame work, hinged locking arrangements, complete with funnels, GI test links (50 x 6 mm), two runs of 25 x 6mm G.I strips for connecting G.I plate & test link etc. including excavation of ground in all types of soils, refilling & removal of excess earth within a radius of 3000 m etc. all as required as per the drawings, specifications & instructed by Engineer-in-charge. Note:- 1. The chamber cover & frame shall be got approved by Department & painted with two coats of red oxide & one coat of enamel paint. 2. Painting of earth value & test date on cover plate. 3. All earthing stations in one building shall be interconnected to each other . 4. Earthing strips shall be welded with the earthing plate before galvanizing & two holes on each strip & plate shall be made for fixing the screws.

Earthing strips: Supply, installation, testing & commissioning of 25 x 6mm sizes of heavy dipped GI strip fixed to wall / slab / column / beam with 2mm thick GI saddle & 4-5 mm thick GI Spacer or in ground at a depth of 750 mm below ground level including excavation in all type of soil , refilling and removal of excess earth within a radius of 3000 mtrs., temporary reinstatement and back filling of trench, interconnection of earth strips / wires with GI nut bolts & washers, painting with two coats of black bituminous compound for earth strip in ground and green colour enamel painting for strip on surface etc. all as required & instructed by the Engineer-in-charge.

In ground (25 x 6mm)

On wall / slab / column / beam/ Trench (25 x 6mm)

Reinstallation of existing 25 x 6 mm Cu earthing strip with hot dip GI spacer saddle fixed to wall / slab / column / beam with 2mm thick GI saddle & 4-5 mm thick GI Spacer interconnection of earth strips / wires with GI nut bolts & washers, painting with green colour enamel painting for strip on surface etc. all as required & instructed by the Engineer-in-charge.

Fabrication, supply and installtion MS powder coated box made up of 16SWG MS CRCA sheet,powder coated etc.,fixing on wall with suitable barcket made up of suitable MS flat painted with one coat of red oxide and 2 coats of enamel paint,suitable anchor fastners/coach screws and as instrcuted by E.I.C

Dismentalling of existing Lan point wiring incluidng I/Os etc complete in all respect and taken away by agency as per instruction of engineer in charge.

Dismentalling of existing telephone point wiring incluidng I/Os etc complete in all respect and taken away by agency as per instruction of engineer in charge.

Supply, installation, testing & commissioning of LED luminaires complete with accessories etc on surface of slab/beam by 2 nos (minimum) of 6 mm anchor fasteners or on wall with 2 nos of wood screws, nylon plug etc.,suitable supporting frame fixed with rag bolts grouted on the wall/anchor fastener on the beam/on the column & other fixing accessories etc provision & connection with 1.5 sq.mm multistranded copper conductor FRLS PVC wires etc., all as per drawing, specifications & as per the instruction of E.I.C. Notes: 1) Sample luminaire/fittings shall be got approved from Dept with complete technical data. 2) All luminairess shall be with drivers. 3) Cost of mounting accessories shall be included in luminaires cost. 4) The lumen output indicated is minimum system output of luminaire. 5) No negative tolerance is allowed on minimum system performance parameters indicated in the SOQ and specifications. 6) The CCT of the luminaire shall be decided as per Instruction of EIC during execution.

Supply ,installation testing and commissioning of Fully diffused recessed mounted 2'X2' LED luminaire with high transmitive diffuser suitable for indoor spaces with min 100lm/W having Lumen output 3000lm etc. as per instruction of EIC.

Supply ,installation testing and commissioning of Surface mounted Highbay LED fixture with min efficacy :- 125 lm/W, min.lumen output :- 10000 Lm ,CCT :- 5700/6500K ,min.CRI :- 80, min. P.f :- 0.95, min. I.P :- 66 weather proof as per instruction of EIC. Note: The fixture to be got approved by department before manufacturing/supply. Warranty certificates shall be submitted to department. Scope work also includes dismantling of the exisitng fixtures. Suitable ladder arrangment for fixing highway luminaires shall be in scope of agency.

Supply ,installation testing and commissioning of Street light LED luminaries having min efficacy :140 lm/W, min.lumen output :- 11000 Lm , CCT :- 5700/6500 K min.CRI :-80 min. P.f :- 0.95 min IP:- 66 min IK:- 08 and pressure die cast Aluminium housing& as per tender specification Scope also includes 3Cx2.5 sq. mm copper conductor PVC insulated TRS wires, earthing of fixture etc. (Independent wiring to be done for each fixture from external terminal box). Note: The fixture to be got approved by department before manufacturing/supply. The fixtures shall have replacement warranty of 5 years from date of supply. Warranty certificates shall be submitted to department. Scope work also includes dismantling of the exisitng fixtures.Suitable ladder for fixing highway luminaires shall be arranged by agency.

LED egress surface/recess, maintained type luminaire (double side viewing) in corridor near staircase with 1 hour backup similar to PEL LED E/M of M/s Prolite with all required hardware, egress symbols etc as per instructions of EIC.

Supply & laying of 50/42 mm OD/ID self lubricated HDPE pipes in ground at depth of 600 mm including fixed onwall/column/slab/existing cable tray/ trench /shaft /pit etc with 5mm thick M.S. flat /GIspacer/angle/ support fixed with coach screws/ grouted inwall/anchor fasteners 2mm thick G.I. fabricated saddle, all fixing accessories, etc complete including painting of M.Sspacers/angles all as per the attached work specification and instructions of EIC. Note: 1) The scope of work includes HDPE pipe accessories suchas couplers, cable end plugs, cable sealing plugs etc.

Supply, fabrication and installation of supports/ MS chequred plate/channel/angle / flat/ MS rod hangers etc.including cutting, fabrication, welding etc. and painting with two coats of primer and two coats of enamel/ PU paint of approved shade as per instructions of EIC.

Supply, fixing & installation of pre mixed & ready to use M/s. HILTI make firestop foam CP 620 in 300ml bottle for sealing openings in electrical shafts, Telephone shaft,raceways & cutouts, hump pipes & where ever required & as per instruction of EIC.

Supply, fixing & installation of pre mixed & ready to use M/s. HILTI make firestop mortar CP 636 or equivalent for sealing openings in electrical shafts, Telephone shaft, raceways & cutouts, hump pipes & where ever required & as per instruction of EIC.

Supply and application of intumescent based coating with M/s. HILTI make firestop cable coat CP 678 or equivalent on cables in cable tray/electrical shafts & where ever required & as per instruction of EIC.

Supplying and fixing of 150mm width x 100 mm depth sizes of GI wire mesh tray, hot dipped galvanised between 60 and 80 microns of zinc as per BS 729 carbon Steel cable trays including horizontal and vertical bends, reducers, tees, cross members and other accessories as required, and duly suspended from the ceiling with electro-zinc coated TF rods, wall mounting brackets etc.