Airports Authority Of India Tender

Supply, Installation, Testing and Commissioning of LED RGBW Linear Wall Washer luminaire of minimum 72 watt of length 1 Meter at least for Facade lighting with aluminium extruded housing, of following wattage. Luminaire shall be capable of producing dynamic color changing light for with 16 million colors by DMX/Ethernet based control. The beam angle of the fittings shall be narrow, medium, wide or asymmetric as per the requirement. Luminaire shall be complete with driver and capable of operating at line voltage without any separate power supply from 100-270VAC, 50Hz with power factor0.9. Fixture shall be suitable to operate at an ambient temperature range of-10°Cto+50°and shall be IP65 and IK06 rated. Lifetime shall be at least L70:50000 burning hours at 50°C . Luminaire shall be conforming to BIS (IS10322)and shall be complete with all necessary accessories required for proper working of fixture including weatherproof connection cables ,waterproof connectors etc. as required.

SITC of Compact master Content Program Controller (DMX controller) with suitable size capability DMX512 universes, playback scenes and animations stored in its SD card, and it can be used for offline scenes scheduling, setting brightness, white balance and playback speed adjustments. It should be able to amplify the DMX signal in cascaded connection & support automatic playback scheduling. It should support power-on startup and scheduled timing start along with capability of unattended operation and remote scene triggering if needed. The Input voltage shall be 12VDC & shall have RJ45 port on Input side. The IEC classification shall be Class III. It should operate on DM512 protocol. The Content Program Controller shall have one SD card slot for maximum 32GB card & the SD card being used shall be FAT32 format. The Content Program Controller shall come with 220-240V to 12V DC power supply. The IP rating of content program controller shall be IP20. The working temperature range shall be -10°C to 50°C complete as required. •Operating Temperature - 10 to 50 Centigrade • Minimum supported LED nodes up to 10000 • Network Data compatibility Ethernet protocol. • The software composer required to create light shows for DMX controller/DMX programming. • Connector/Cable: (2) RJ45 ports, shielded Cat. 6 or better data cable of required length to be included for communication • Work as stand alone or computer driven controller. • Environment: Dry indoor location. •Ethernet keypad module for the DMX controller for selecting multiple scene. •Ethernet Compact keypad that triggers the controller •Secure Digital SD card drive for flexible show •USB 2.0 interface for downloading shows and configuring from attached PC • All others items required for successful functioning of DMX controller including the programming for all days throughout the year as directed by EIC shall be considered and included in the quoted rate.

SITC of DMX Amplifier / Booster / Splitter/ complying with DMX512 protocol. The Compact signal amplifier shall support magnetic isolation protection, protects the controllers and ensures that the DMX signal can be normally transmitted to various luminaires, improving the reliability and stability of the entire control system. The DMX controller shall be compact in size & shall be capable for outdoor application. Amplifier shall support online automatic addressing & should be able to amplify the signal for up DMX 512 controller and luminaires. The DMX amplifier shall be so designed that it does not by-pass the input volt to avoid any short circuit. On the input side the amplifier shall have 4-Pole DMX cable & a cable for DC Input with 2-Pole connector complete as required.

SITC of DMX Amplifier / Booster / Splitter/ complying with DMX512 protocol. The Compact signal amplifier shall support magnetic isolation protection, protects the controllers and ensures that the DMX signal can be normally transmitted to various luminaires, improving the reliability and stability of the entire control system. The DMX controller shall be compact in size & shall be capable for outdoor application. Amplifier shall support online automatic addressing & should be able to amplify the signal for up DMX 512 controller and luminaires. The DMX amplifier shall be so designed that it does not by-pass the input volt to avoid any short circuit. On the input side and output side the amplifier shall have cable with 5-Pole DMX/ DC connector complete as required.

SITC of 2M long lead cable with IP67 5-Pin connector at one end. The Pin material should be copper. The cable shall have insulation resistance of ≥ 10Mꭥ complete as required.

SITC of 2M long jump cable with IP67 4-Pin connector at one end. The Pin material should be copper. The operating voltage shall be 60V DC. Cable shall have insulation resistance of ≥ 10Mꭥ complete as required .

SITC of 2M long lead cable with IP67 5-Pin connector at one end. The Pin material should be copper. The cable shall have insulation resistance of ≥ 10Mꭥ complete as required.

SITC of 2M long jump cable with IP67 4-Pin connector at one end. The Pin material should be copper. The operating voltage shall be 60V DC. The cable shall have insulation resistance of ≥ 10Mꭥ complete as required .

Supply and laying of DMX cable in existing conduit to make connection s with light controllers and amplifier as per the design complete as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Supplying and laying of 63 mm dia (OD-63 mm & ID-51 mm nominal) size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench/ surface complete as required.

Supplying and laying of 63 mm dia (OD-63 mm & ID-51 mm nominal) size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc. , complete as required.

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of following size in the existing RCC/HUME/Metal/HDPE pipe as required. Upto 35 sq. mm

Supplying and making end termination with brass double compression flame proof gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 4 core, 25 Sq.mm.

Supply of the following 1100 volts grade, copper conductor FRLS PVC Insulated Sheathed Flexible Cable as per IS694 and latest amendment and as per other relevant standards and tender specification. 4C X 2.5 sqmm

Supply of the following 1100 volts grade, copper conductor FRLS PVC Insulated Sheathed Flexible Cable as per IS694 and latest amendment and as per other relevant standards and tender specification. 4C X 4 sqmm

Supply of following size of  1.1 KV grade, XLPE insulated PVC sheathed Copper Conductor armoured cable confirming to IS: 7098 part -I amended upto date. 4 core X 4 Sq.mm 

Supply of following size of  1.1 KV grade, XLPE insulated PVC sheathed Aluminium Conductor armoured cable confirming to IS: 7098 part -I amended upto date. 4 core X 25 Sq.mm 

Supply of following size of  1.1 KV grade, XLPE insulated PVC sheathed Aluminium Conductor armoured cable confirming to IS: 7098 part -I amended upto date. 3 core X 2.5 Sq.mm 

Supply of following size of  1.1 KV grade, XLPE insulated PVC sheathed Aluminium Conductor armoured cable confirming to IS: 7098 part -I amended upto date. 3 core X 1.5 Sq.mm 

Laying of following sizes of FRLS PVC insulated copper conductor, cable in the existing surface/ recessed steel/ PVC conduit as required. 4C X 2.5 sqmm

Laying of following sizes of FRLS PVC insulated copper conductor, cable in the existing surface/ recessed steel/ PVC conduit as required. 4C X 4 sqmm

Supplying and fixing following 4way, Vertical type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder coating including earthing etc as required ( i/c the following MCB’s) a) 4 way (4 + 12), Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole - 6A-32A

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Double pole - 32 A

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Triple pole and neutral - 63 A

SITC of VTPN DB's and modules, shall be pre assembled with vertical bus bars & minimum IP-55, suitable for outdoor/harsh environment like resistant to weather influences (humidity, temperature, water sprays), chemical resistance etc i/c following MCCB's & MCB's. VTPN DB INCOMER - 250 Amps, 36kA, 4P MCCB, Isc = Icu = 100%, Microprocessor based, i/c OL & SC protection OUTGOING - 36 nos. modules for MCB's as required i/c following 'C' Curve MCB's (10KA) 63 A, 4P MCB-02 Nos 40 A, 4P MCB-02 Nos 10 to 32 A, DP MCB -10 Nos

Supplying and fixing of 20 mm sizes of medium class PVC conduit along with accessories in surface/recess including cutting tiles on ground and making good the same in case of recessed conduit as required.

Supplying and fixing of 25 mm sizes of medium class PVC conduit along with accessories in surface/recess including cutting tiles on ground and making good the same in case of recessed conduit as required.

Supplying and fixing of 32 mm sizes of medium class PVC conduit along with accessories in surface/recess including cutting tiles on ground and making good the same in case of recessed conduit as required.