Urban Administration And Development Tender

Distempering with 1st quality acrylic distemper (ready mixed) of approved manufacturer, of required shade and colour complete, as per Two or more coats on new work.

Painting with black anti-corrosive bitumastic paint of approved

Painting on G.S. sheet with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : New work (two or more coats) including a coat of approvedsteel primer but

Providing and fixing factory made UPVC door frame made of UPVC extruded section having an overall dimension as below (tolerance ±1mm) with wall thickness 2.0mm ± 0.2mm, corners of the door frame to be mitred and welded of plastic, galvanized brackets and stainless steel screws. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19mm and 1mm ± 0.1mm wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturers specification and direction of Engineer-in-charge Extruded section profile size 48x40 mm.

Providing and fixing to existing door frames.24 mm thick factory made PVC door shutters made of styles and rails of a UPVC hollow section of size 59x24 mm and wall thickness 2 mm ± 0.2 mm with inbuilt edging on both sides.The styles and rails mitred and joined at the corners by means of M.S. galvanised/plastic brackets of size 75x220 mm having wall thickness 1.0mm and stainless steel screws.The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm ± 0.1 mm wall thickness.The lock rail made up of 'H' section, a UPVC hollow section of size 100x24 mm and 2 mm ± 0.2 mm wall thickness fixed to the shutter styles by means of plastic/galvanised M.S. 'U' cleats. The shutter frame filled with a UPVC multi- chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm ± 0.1 mm wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers,complete as per manufacturer's specification and direction of Engineer-in- charge. (For W.C. and bathroom door shutter).

Providing and placing on terrace at all floor polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete:

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using flats 30x6mm for diagonal braces and central cross piece.

62 mm thick cement concrete flooring with concrete hardener topping under layer 50 mm thick cement concrete grade M-15 (Nominal Mix with 20mm maximum size of stone aggregate) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6mm nominal size) by volume. Hardening compound is mixed @ 2 litre per 50kg of cement or as per manufactures specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (6 to 7mm thick) of approved make in all colours, shades of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying rectified Glazed Ceramic wall tiles 300x450 mm or more (8mm to 10mm thick) of 1st quality conforming to IS : 15622 of approved make in all colours, laid on 12 mm thick Cement Mortar 1:3 (1 Cement : 3 Coarse sand) including grauting the joints with white cement and matching pigments etc., complete.

Providing and fixing white vitreous china water closet squatting pan (Indian type) P or S trap, complete including cutting and making good the walls and floors wherever required :.Orissa pattern W.C. pan of size 580x440 mm

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm or 340x410 x265mm sizes respectively.

Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings : Flat back wash basin of size 550x400mm.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plane and brass threaded fitting i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall. 15 mm nominal outer dia .Pipes.

20 mm nominal outer dia .Pipes.

Providing and fixing brass stop cock of approved quality : 15 mm nominal bore 0.40kg

Artist Painting work as per design artistic graphics painting work as per design of mandana, sohrai, etc foil painting art of mp and gond painting, graffiti painting, modern painting, and with required at site condition/ situtuition with acrylic 3D paint (Acrylic), ACE asian paint colour or similar quality approved by EIC with two or more coats for prepration of base with basw colour

Artist Painting work as per design artistic graphics painting work as per design of mandana, sohrai, etc foil painting art of mp and gond painting, graffiti painting, modern painting, and with required at site condition/ situtuition with acrylic 3D paint (oil based), ACE asian paint colour or similar quality approved by EIC with two or more coats for prepration of base with base colour