Urban Administration And Development Tender

39.4 Supplying and laying of approved Make HDPE pipe as per IS : 4984 and IS : 14333 with latest amendment for installation of submersible pump with necessary connection, socket/couplings, Tees,etc. as required (PE-63 & working Pressure 10 kgf/sq cm) 50 mm Outer Dia.

Supplying & installing G.I. pipe for protection of underground cable fixed on wall/support/in trench/fixed between two rigid existing support of wall/beam for erection of ceiling Fan/down rod for stiff pendent for light luminaries /fan/protective for earthing, lightening conductor down strip/overhead service line/for submersible cable or centrifugal pump for water supply with necessary iron clamp coupler, bend, tee, elbow, nuts and bolts etc. complete in an approved manner as required to complete excluding cost of excavation/dismantling & other finished masonry Item complete. 50.00mm

Supply and laying testing & commissioning of following sizes of Copper conductor control cables on existing tray including fixing clamps & proper connections to equipment etc.complete as required. 46.41.3 4Cx2.5 sq.mm

Earthing with G.I. Earth plate 600mm X 600mm X 6mm thick including accessories and providing masonary encloser in cement mortor, cover plate having locking arrangement on the top and G.I. watering pipe 20mm dia 2.7 Metre long etc. (but without charcoal or coke and salt ) complete as required.

Add Extra for using salt and charcoal / coke for G.I. Plate or Copper plate earth electrode as required including excavation & refilling.

Supply and laying 4.0mm (8 SWG) dia. G.I. wire at 0.5 metre below ground level as conductor earth electrode including jointing etc. as required

Providing and laying earth connections from earth electrode with 4.00 mm dia copper wire in 15mm dia G.I. Pipe from earth electrode as required

Providing and fixing 25mm X 5mm copper strip on surface or in recessed for connection etc. as required

Supply, fixing, testing & commissioning wall/floor mounted LT panel primer coated with powder coated paint & provided with required gasket for dust/vermin proof with degree of protection IP42 suitable for 415Volt 3 phase, 50 Hz, 4 wire system fabricated out of CRCA sheet upto 2 mm thick (1.6 mm for doors) duly compartmentalized for incomer, bus section, outgoings, cable alleys & CT, PT Ampere Metre, Volt Metre, selector switches, frequency Metre, phase indicating lamp, Energy Metre complete including cost of busbar supports, detachable cable gland plates, 2 earthing terminals, internal wiring & fixing of separately supplied MCBs, MCCBs, ACB, panel mounted changeover switch/SFUs, etc. as required but excluding cost of busbar strips, Ampere Metre, Volt Metre, selector switch as per approved design & specfication

Supplying and fixing of LT Panel accessories of approved make in existing LT Panel including connections etc. as required as per spececification Contractor 2 Pole rating 240/415V 40A

MCCB current rating – upto 63 Amp, 10kA, 3P 415V AC- INCOMMING

MCB SP 6Amp to 32Amp 10kA rating -OUT GOING

mccb 25 ka current rating-160 amp adjustable overload setting 80%-100% of in,adjustable short circuit setting 6-10 in 4 pole

MCCB with Breaking Capacity 10 KA at 415 V Current Rating -25 to100 Amps

Supplying & installation approved make SMC press moulded composite FRP. loop-in, loop-out approx. 2mm thick box complete with bakelite connector strip 4way & hinged doors having locking arrangements with mounting clamp with nuts, bolts & washers suitable for erection on ground with cable clamps& earth bolt of according to light size (BOQ)

Supply of 1000mm long rigid architectural 3000K LED Linear light with integral driver & housing of Extruded aluminium alloy 6063 grade & die-cast aluminium end caps. The luminaire shall have electrostatically applied polyester powder coating finish. The luminaire width shall be 38mm & height of 47mm without brackets. The luminaire’s integrated brackets shall be made of extruded aluminium & the same shall be so designed that the luminaire can be tilted ±95°. The luminaire shall have silicon glue between optical cover & LED chamber to ensure proper IP66 protection. The nominal weight of the luminaire shall be 1.55KG (±10%). The luminaire shall be equipped with high-power Cree, osram, lumiled or equivalent. The fixture shall have 30° beam angle & the lens shall be made of anti-aging & anti UV-PMMA material. The optical cover shall be made of IK06 rated clear tempered glass. The LEDs shall have minimum CRI ≥80 & shall have SDCM≤4. The luminaire shall have system wattage not exceeding 24W and system lumen output of not less than 1600 lumens. Fixture shall operating temperature range of -40°C to 50°C. The fixture shall have an integral driver with input voltage for 24 V DC. The luminaire shall have declared life of 50,000 burning hours at L70 @ 35deg. The luminaire shall have class I insulation. The successful bidder shall submit the following certifications/reports for approval before supply of materials: product data sheets, LM79 report from NABL accredited lab, illuminance diagram, polar curve & LM80 report issued by LED manufacturer & RoHS Compliance alone with CE certificate. The bidder shall upload the luminaire BIS certificate along with technical bid. The luminaire shall be supplied with necessary connectors for connecting lead/jump cables & necessary end plates / covers. BIS Approved and NABL Test report IP Testing Report,IK Report

Supply of 1000mm long rigid architectural 3000K LED Linear light with integral driver & housing of Extruded aluminium alloy 6063 grade & die-cast aluminium end caps. The luminaire shall have electrostatically applied polyester powder coating finish. The luminaire width shall be 38mm & height of 47mm without brackets. The luminaire’s integrated brackets shall be made of extruded aluminium & the same shall be so designed that the luminaire can be tilted ±95°. The luminaire shall have silicon glue between optical cover & LED chamber to ensure proper IP66 protection. The nominal weight of the luminaire shall be 1.55KG (±10%). The luminaire shall be equipped with high-power Cree, osram, lumiled or equivalent. The fixture shall have 16x35° beam angle & the lens shall be made of anti-aging & anti UV-PMMA material. The optical cover shall be made of IK06 rated clear tempered glass. The LEDs shall have minimum CRI ≥80 & shall have SDCM≤4. The luminaire shall have system wattage not exceeding 36W and system lumen output of not less than 2350 lumens. Fixture shall operating temperature range of -40°C to 50°C. The fixture shall have an integral driver with input voltage for 24 V DC. The luminaire shall have declared life of 50,000 burning hours at L70 @ 35deg. The luminaire shall have class I insulation. The successful bidder shall submit the following certifications/reports for approval before supply of materials: product data sheets, LM79 report from NABL accredited lab, illuminance diagram, polar curve & LM80 report issued by LED manufacturer & RoHS Compliance alone with CE certificate. The bidder shall upload the luminaire BIS certificate along with technical bid. The luminaire shall be supplied with necessary connectors for connecting lead/jump cables & necessary end plates / covers. BIS Approved and NABL Test report IP Testing Report,IK Report

Supply of 300mm long rigid architectural RGBW (W=3000K) LED Linear light with integral driver & housing of Extruded aluminium alloy 6063 grade & die-cast aluminium end caps. The luminaire shall have electrostatically applied polyester powder coating finish. The luminaire width shall be 38mm & height of 47mm without brackets. The luminaire’s integrated brackets shall be made of extruded aluminium & the same shall be so designed that the luminaire can be tilted ±95°. The luminaire shall have silicon glue between optical cover & LED chamber to ensure proper IP66 protection. The nominal weight of the luminaire shall be 0.6KG (±10%). The luminaire shall be equipped with high-power Cree, osram, lumiled or equivalent. The fixture shall have 30° beam angle & the lens shall be made of anti-aging & anti UV-PMMA material. The optical cover shall be made of IK06 rated clear tempered glass. The LEDs shall have minimum CRI ≥80 & shall have SDCM≤4. The fixture shall come with power & DMX cable of minimum 100mm length. The fixtures shall be installed with have IP67 connectors. The luminaire shall have system wattage not exceeding 9W and system lumen output of not less than 440 lumens. Fixture shall operating temperature range of -40°C to 50°C. The fixture shall have an integral driver with input voltage for 24V DC. The luminaire shall have declared life of 50,000 burning hours at L70 @ 35deg. The luminaire shall have class I insulation. The luminaire shall be compatible with DMX512 controller. The luminaire shall automatically addressable using hand-held addressing device. The luminaire shall be capable of 8-bit control of RED, Green, Blue & White (W=4000K) to produce 16.7million colours. The luminaire shall be capable of digital dimming of 65536 steps. The successful bidder shall submit the following certifications/reports for approval before supply of materials: product data sheets, LM79 report from NABL accredited lab, illuminance diagram, polar curve & LM80 report issued by LED manufacturer & RoHS Compliance alone with CE certificate. The bidder shall upload the luminaire BIS certificate along with technical bid. The luminaire shall be supplied with necessary connectors for connecting lead/jump cables & necessary end plates / covers. Make - Philiphs /Osram/ Neri

Supply of 500mm long rigid architectural 3000K LED Linear light with integral driver & housing of Extruded aluminium alloy 6063 grade & die-cast aluminium end caps. The luminaire shall have electrostatically applied polyester powder coating finish. The luminaire width shall be 45mm & height of 105mm without brackets. The luminaire’s integrated brackets shall be made of extruded aluminium & the same shall be so designed that the luminaire can be tilted ±95°. The luminaire shall have silicon glue between optical cover & LED chamber to ensure proper IP66 protection. The nominal weight of the luminaire shall be 2KG (±10%). The luminaire shall be equipped with high-power Cree, osram, lumiled or equivalent. The fixture shall have 16x35° beam angle & the lens shall be made of anti-aging & anti UV-PMMA material. The optical cover shall be made of IK06 rated clear tempered glass. The LEDs shall have minimum CRI ≥80 & shall have SDCM≤4. The luminaire shall have system wattage not exceeding 27W and system lumen output of not less than 1240 lumens. Fixture shall operating temperature range of -40°C to 50°C. The fixture shall have an integral driver with input voltage for 220-240 V AC. The luminaire shall have declared life of 50,000 burning hours at L70 @ 35deg. The luminaire shall have class I insulation. The successful bidder shall submit the following certifications/reports for approval before supply of materials: product data sheets, LM79 report from NABL accredited lab, illuminance diagram, polar curve & LM80 report issued by LED manufacturer & RoHS Compliance alone with CE certificate. The bidder shall upload the luminaire BIS certificate along with technical bid. The luminaire shall be supplied with necessary connectors for connecting lead/jump cables & necessary end plates / covers. BIS Approved and NABL Test report IP Testing Report,IK Report

Supply of exterior IP68 LED 3000K Flexible light strip of 5 mtr standard length with 10-15 Watt per meter which can be compatible with the DMX / Ethernet controller. Minimum System lumens ofminimum 1100 lumens/meter. Luminaire light beam spread - 110°, The Strip should have IP 68 protection and is offered IP 67 rated connector to join the LED Strips incontinuity. The luminaire must be offered with Aluminum channel for mounting the strip lights. The product should be complete with all accessories and Driver. The successful bidder shall submit the following certifications/reports for approval before supply of materials: product data sheets, LM79 report from NABL accredited lab, illuminance diagram, polar curve & LM80 report issued by LED manufacturer & RoHS Compliance alone with CE certificate. The bidder shall upload the luminaire BIS certificate along with technical bid. The luminaire shall be supplied with necessary connectors for connecting lead/jump cables. BIS Approved and NABL Test report IP Testing Report,IK Report

Supply of exterior IP68 LED RGB/RGBW Flexible light strip of 5 mtr standard length with 10-15 Watt per meter which can be compatible with the DMX / Ethernet controller. Minimum System lumens ofminimum 450 lumens/meter and System Lumen Efficacy 30lm/w. Luminaire light beam spread - 110°, The Strip should have IP 68 protection and is offered IP 67 rated connector to join the LED Strips incontinuity. The luminaire must be offered with Aluminum channel for mounting the strip lights. The product should be complete with all accessories and Driver. The successful bidder shall submit the following certifications/reports for approval before supply of materials: product data sheets, LM79 report from NABL accredited lab, illuminance diagram, polar curve & LM80 report issued by LED manufacturer & RoHS Compliance alone with CE certificate. The bidder shall upload the luminaire BIS certificate along with technical bid. The luminaire shall be supplied with necessary connectors for connecting lead/jump cables. BIS Approved and NABL Test report IP Testing Report,IK Report

Supply of Spike mounted fixture LED 3000K 100-240Vac CRI 80 Input power: 8W, 520lm Dimension Ø60 mm x 80 mm x 98.5 mm Beam Angle: 20°, inbuilt Electronic driver ON/OFF CE/CB, IP rating IP65, Mechanical resistance IK06. MATERIAL CHARACTERISTICS : Die - Cast aluminium housing with electrostatic powder coating & high quality temper glass with precise PMMA optics for light distribution . Ground mounting spike made of die cast aluminum. Electrostatic powder coated. This luminaire contains built-in LED modules. Operating ambient temperature range is from -40°C to +50°C. working humidity upto 95%. Manufacturer shall have inhouse lab approved by NABL or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. Both the fixture and Driver should have separate BIS approval. BIS Approved and NABL Test report IP Testing Report,IK Report

Supply of High Pressure Die Cast Aluminium (LM6) Alloy hosuing SMD LED Floodlight Luminaire of 4700 lumen, efficacy 135lm/w, product with Compnay LOGO, Corelated Color Temp 3000k,CRI70,Maintenance of lumen L70 (Hrs) 50K@L70, high efficiency glass cover.Protection of Fixture:- IP66,IK07,Line Frequency 50 HZ,power factor 0.95,Deriver Efficiency 85%. LManufacturer shall have inhouse lab approved by NABL or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. Both the fixture and Driver should have separate BIS approval. BIS Approved and NABL Test report IP Testing Report,IK Report

Supply of High Pressure Die Cast Aluminium (LM6) Alloy hosuing SMD LED Floodlight Luminaire of 9300 lumen, efficacy 135lm/w, product with Compnay LOGO, Corelated Color Temp 3000k,CRI70,Maintenance of lumen L70 (Hrs) 50K@L70, high efficiency glass cover.Protection of Fixture:- IP66,IK07,Line Frequency 50 HZ,power factor 0.95,Deriver Efficiency 85%. LManufacturer shall have inhouse lab approved by NABL or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. Both the fixture and Driver should have separate BIS Approved and NABL Test report IP Testing Report,IK Report

Supply of Circular shape architectural RGBW (W=3000K) LED flood light with integral driver & housing made of Die-cast aluminium alloy - ADC12. The luminaire shall be no bigger than Ø 170 X 125 (±10%) without bracket. The luminaire shall have electrostatically applied polyester powder coating finish. The luminaire bracket shall be made of cold-rolled steel & shall be so designed that the luminaire can be tilted to ±90°. The bracket shall have locking mechanism to fix & secure the desired tilt angle. The luminaire shall have silicon gasket between optical cover & LED chamber to ensure proper IP66 protection. The luminaire must have a breather gland. The nominal weight of the luminaire shall be 3KG (±10%). The luminaire shall be equipped with high-power Cree, osram, lumiled or equivalent. The fixture shall have 30° beam angle & the lens shall be made of anti-aging & anti UV-PMMA material. The optical cover shall be made of IK06 rated clear tempered glass. The LEDs shall have minimum CRI ≥80 for white light & shall have SDCM≤4. The fixture shall come with power & DMX cable of minimum 100mm length. The fixtures shall be installed with have IP67 connectors. The luminaire shall have system wattage not exceeding 40W and system lumen output of not less than 1870 lumens ±5%. Fixture shall operating temperature range of -40°C to 50°C. The fixture shall have an integral driver with input voltage for 220-240 VAC, 50/60Hz. The luminaire shall have declared life of 50,000 burning hours at L70 @ 35deg. The luminaire shall have class I insulation. The luminaire shall be compatible with DMX512 controller. The luminaire shall automatically addressable using hand-held addressing device. The luminaire shall give feedback on luminaire address & status (ON & Off). The luminaire shall be capable of 8-bit control of RED, Green, Blue & White (W=4000K) to produce 16.7million colours. The luminaire shall be capable of digital dimming of 65536 steps. The successful bidder shall submit the following certifications/reports for approval before supply of materials: product data sheets, LM79 report from NABL accredited lab, illuminance diagram, polar curve & LM80 report issued by LED manufacturer & RoHS Compliance alone with CE certificate. The bidder shall upload the luminaire BIS certificate along with technical bid. The luminaire shall be supplied with necessary connectors for connecting lead/jump cables.BIS Approved and NABL Test report IP Testing Report,IK Report

Supply of Circular shape architectural RGBW (W=3000K) LED flood light with integral driver & housing made of Die-cast aluminium alloy - ADC12. The luminaire shall be no bigger than Ø 170 X 125 (±10%) without bracket. The luminaire shall have electrostatically applied polyester powder coating finish. The luminaire bracket shall be made of cold-rolled steel & shall be so designed that the luminaire can be tilted to ±90°. The bracket shall have locking mechanism to fix & secure the desired tilt angle. The luminaire shall have silicon gasket between optical cover & LED chamber to ensure proper IP66 protection. The luminaire must have a breather gland. The nominal weight of the luminaire shall be 3KG (±10%). The luminaire shall be equipped with high-power Cree, osram, lumiled or equivalent. The fixture shall have 30° beam angle & the lens shall be made of anti-aging & anti UV-PMMA material. The optical cover shall be made of IK06 rated clear tempered glass. The LEDs shall have minimum CRI ≥80 for white light & shall have SDCM≤4. The fixture shall come with power & DMX cable of minimum 100mm length. The fixtures shall be installed with have IP67 connectors. The luminaire shall have system wattage not exceeding 50W and system lumen output of not less than 2530 lumens ±5%. Fixture shall operating temperature range of -40°C to 50°C. The fixture shall have an integral driver with input voltage for 220-240 VAC, 50/60Hz. The luminaire shall have declared life of 50,000 burning hours at L70 @ 35deg. The luminaire shall have class I insulation. The luminaire shall be compatible with DMX512 controller. The luminaire shall automatically addressable using hand-held addressing device. The luminaire shall give feedback on luminaire address & status (ON & Off). The luminaire shall be capable of 8-bit control of RED, Green, Blue & White (W=4000K) to produce 16.7million colours. The luminaire shall be capable of digital dimming of 65536 steps. The successful bidder shall submit the following certifications/reports for approval before supply of materials: product data sheets, LM79 report from NABL accredited lab, illuminance diagram, polar curve & LM80 report issued by LED manufacturer & RoHS Compliance alone with CE certificate. The bidder shall upload the luminaire BIS certificate along with technical bid. The luminaire shall be supplied with necessary connectors for connecting lead/jump cables. BIS Approved and NABL Test report IP Testing Report,IK Report

Supply of Compact master Content Program Controller (DMX controller) with capability to control minimum 8 DMX512 universes, playback scenes and animations stored in its SD card, and it can be used for offline scenes scheduling, setting brightness, white balance and playback speed adjustments. It should be able to amplify the DMX signal in cascaded connection & support automatic playback scheduling. It should support power-on startup and scheduled timing start along with capability of unattended operation and remote scene triggering if needed. The Content Program Controller shall have integrated LCD display & support IR remote control. The dimensions of the Content Program Controller shall be approximately 278X193X66 mm (±10%). It should be housed in aluminium casing. The Input voltage shall be 12VDC & shall have 2 RJ45 ports on Input side. The IEC classification shall be Class III. It should operate on DM512 protocol. The output shall have 8 X 3P lockable terminals. The power consumption shall be 8W (±10%). The Content Program Controller shall have one SD card slot for maximum 32GB card & the SD card being used shall be FAT32 format. The Content Program Controller shall come with 220-240V to 12V DC power supply. The IP rating of content program controller shall be IP20 & shall comply to CE, CB & CQC certifications. The DMX controller/content program controller shall be from the same make/brand/manufacturer as that of façade lighting luminaires. The working temperature range shall be -30°C to 50°C. The successful bidder shall submit the technical data sheet for approval before supply of material. BIS Approved and NABL Test report IP Testing Report,IK Report

DMX KIT

4 point DMX jumper cable for interconnecting the façade luminaires having length min 2m length (min 10 nos in 1 packet)

4 point DMX leader cable for connecting luminaire with power supply having length min 2m length (min 10 nos in 1 packet)

5 point DMX jumper cable for connecting luminaire with power supply having length min 2m length (min 10 nos in 1 packet)

5 point DMX leader cable for connecting luminaire with power supply having length min 2m length (min 10 nos in 1 packet)

Supply of IP65 driver 150W

Endcap female connectors for closing the conenctions (min 20 nos in 1 packet)

Endcap Male connectors for closing the conenctions (min 20 nos in 1 packet)