South Eastern Coalfields Limited Tender

PART-B

2.8.1 Earth work in excavation by mechanical means (Hydraulic Excavator)/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

15.3 Demolishing R.C.C. work, including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

15.7 Demolishing brick work, manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable materialwithin 50 metres lead as per direction of Engineer-in-charge.

Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of: G.S sheet

15.17 Dismantling steel work in single sections including dismembering and stacking within 50 metres lead in:5.17.2 Channels, angles, tees and flats

Brick work with Fly ash bricks of class designation 75 in foundation and plinth in cement mortar 1:6 (1 cement : 6 coarse sand ).

4.1 Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level:

.1 Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement - All work upto plinth level:

5.2 Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. upto floor five level excluding cost of centring, shuttering, finishing and reinforcement :

5.22 : Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete.5.22.4: Hot rolled deformed bars

0.2 : Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete:

12.50: Providing and fixing precoatedgalvanized iron profile sheets (size, shape and pitch of corrugation as 5% total coated thickness (TC T), Zinc coating 120gsm as per IS:277 in approved by Engineer-in-charge) 0.05 mm. 240 mpa mm steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM seal or with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

4.1 Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering -All work upto plinth level:

13.60 Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade, 13.60.1 Two or more coats on new work-

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work. 13.61.1 Two or more coats on new work

13.1 12 mm cement plaster of mix: 13.1.2 1:6 (1 cement : 6 fine sand)

5.9 Centring and shuttering including strutting, propping etc. and removal of form for : 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete.

5.9 Centring and shuttering including strutting, propping etc. and removal of form for : 5.9.2 Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

13.39 Colour washing such as green, blue or buff to give an even shade :- 13.39.1 New work (two or more coats) with a base coat of white washing with lime

Total Impact of GST for The Purpose of CTC