Raja Ramanna Centre For Advanced Technology Tender
Know all about the latest MP tenders along with the tender details and downloadable document on BidAssist. Here, on this page, we shall help you search for every MPtender posted on the official website of mptenders.gov.in according to authority, district, etc. Be it an irrigation tender or MP PWD tender, and we will tell you how to bid for these and more.
Raja Ramanna Centre For Advanced Technology - RRCAT Tender
Eprocure
Opening Date8 Oct 2021
Closing Date20 Oct 2021
Tender Amount₹ 20,95,000
Costs
EMD
Refer DocumentsDocument Cost
Refer DocumentsTender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2021_RRCAT_649640_3Bid Award Id
ViewTender No
RRCAT/CSD/Rev/3028/W-4104Tender Authority
Raja Ramanna Centre For Advanced Technology ViewPurchaser Address
-Website
http://eprocure.gov.in
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
2) In case of unsatisfactory quality of work, reduced rate shall be applied as per clause 16 of Section 5 of the tender. The decision of Engineer regarding reduced rate shall be final & binding.
-
-
-
3) In case of non performance of work at any or all locations,no payment shall be made and recovery shall be made for the measured area of non performance as per the quoted rate per running metre.
-
-
-
Removing and cleaning of chokes/blockages from sewerage lines, manholes, inspection chambers, W.C., gully traps and floor traps etc.by bamboo/ M.S.rods/mechanical means so as to provide the easy flow of sewage/waste water etc.including opening of door bend/jali and refixing the same after clearing of chokage complete as per specifications and as directed by Engineer-in-charge.
20
-
-
Note 1) In case of unsatisfactory quality of work, reduced rate shall be applied as per clause 16 of Section 5 of the tender. The decision of Engineer regarding reduced rate shall be final & binding.
-
-
-
2) In case of non performance of work at any or all locations, no payment shall be made and recovery shall be made for the measured area of non performance as per the quoted rate per choke.
-
-
-
Maintenance of cleanliness around buildings by lifting all waste material, packing boxes, garbage and waste papers etc. on all working days except Sunday and national holidays from all around 20m of the building including transporting the same to the predetermined locations / pits etc. in ARPF campus or in the garbage carrying vehicle of Indore Municipal Corporation standing close to campus ensuring non pilferage etc complete as per specifications and as directed by Engineer-in-Charge
-
-
-
ARPF building and Security post building etc.
12
-
-
Note 1) In case of unsatisfactory quality of work, reduced rate shall be applied as per clause 16 of Section 5 of the tender. The decision of Engineer regarding reduced rate shall be final & binding.
-
-
-
2) In case of non performance of work at any or all locations, no payment shall be made and recovery shall be made for non performance days as per the quoted rate on pro rata days basis.
-
-
-
General cleaning,sweeping,mopping,dusting,swabbing of floors of the rooms at various storeys, passeges,staircases etc including sweeping,cleaning,washing and swabbling of passages in front of all toilets including the cost of entire cosmetic materials on all working days on daily basis and cleaning of ceilings, external faces of walls & parapets, cleaning of glass panes & other members of windows, doors, ventilators, mirrors, handrails, removing of cobwebs once in fifteen days and daily disposing of sweeped waste up to nearest dust bin located outside of the building as directed, disposing the contents of scattered placed dust bins in to the predetermined locations / pits etc. in ARPF campus for final disposal or putting in to the garbage carrying vehicle of Indore Municipal Corporation standing close to campus ensuring non pilferage etc complete including the cost of required safety tools & tackles, necessary safety kit ,Uniform, vacuum cleaner, the cost of soft nylon brushes, brooms and all consumables like cleansing agent such as Harpic or Domex or Homex or other approved agent, phenyl, rubbing papers etc. complete as directed by the Engineer-in-charge.
360000
-
-
Note: (1) This item shall be applicable for general rooms,corridors,stairways,lobbies etc.This item shall not include cleaning & disinfection of toilets which shall be paid separately under relevant item. Only floor area of the building shall be measured for payment. Half area shall be measured if mopping could not be taken up.
-
-
-
(2) The cost incurred for deployment of labourers, tools & tackles in safety kit, Uniform, vacuum cleaner, all taxes, soft nylon brushes, brooms and consumables like cleansing agent such as Harpik or Domex or other approved agent, phenyl, rubbing papers etc shall be deemed to be included in the quoted rate.
-
-
-
(3) The contractor shall deploy as many number of cosmetic helpers as required to ensure that various jobs in whole area of the building including fortnightly jobs and toilets* (*payable separately) gets finished in one working day.
-
-
-
(4) The choking if any not caused due to fault of contractor and existed prior to taking up of cleaning operations shall be paid separately under relevant item as the same is not included in this item. However choking if any which was not existing prior to taking up of cleaning operations shall be considered as choking caused due to fault of contractor and removal of the same shall have to be borne by the contractor for which payment shall not be admissible.
-
-
-
(5) In case of unsatisfactory quality of work, reduced rate shall be applied as per clause 16 of Section 5 of the tender. The decision of Engineer regarding reduced rate shall be final & binding.
-
-
-
(6) In case of non performance of work at any or all locations, no payment shall be made and recovery shall be made for the measured area of non performance as per the quoted rate per sqm.
-
-
-
General cleaning,sweeping,swabbing,disinfecting and making the public toilet fit with improved hygiene by satisfactorily cleaning of all types of dado, walls, floors, sanitary fitments like Indian water closet, European water closet, urinals, wash basins, marble or other type of urinal partitions, flushing units etc. either individually or in combination at all level including cleaning of bath zone with or without internal lobby by using mild acid, Harpic or Domex or Homex or other cleansing agent, bleaching agents, soft nylon brushes, rubbing papers, necessary safety kit, Uniform, ladder,vacuum cleaner etc.including spraying antifungal, anti bacterial fumable liquids,sprinkliling of phenyl, placing of phynapthelene balls, placing air fresheners at ventilators including rectification of joints of tiles using matching coloured air curable compound etc. complete as directed by the Engineer-in-charge.
4000
-
-
This item shall be operated for first frequency of the day and the payment for subsequent frequencies shall be payable under item no 7
-
-
-
Note: (1) Floor area of WC & Urinal portion of toilet shall be measured for payment.Dado,skirting and all types of fitments in this region shall be deemed to be covered up in the quoted rate. No payment shall be made for partially complete/incomplete work. The portion of toilet other than WC & Urinal region shall be measured under the respective item of general cleaning i.e. item no 5.
-
-
-
(2) The cost incurred in cleaning dado, sanitary fitments, cost of all materials, labour, ladder, safety kits etc,vacuum cleaner shall be deemed to be included in the quoted rate.
-
-
-
(3) The choking if any not caused due to fault of contractor and existed prior to taking up of cleaning operations shall be paid separately under relevant item as the same is not included in this item. However choking if any which was not existing prior to taking up of cleaning operations shall be considered as choking caused due to fault of contractor and removal of the same shall have to be borne by the contractor for which payment shall not be admissible.
-
-
-
(4) In case of unsatisfactory quality of work, reduced rate shall be applied as per clause 16 of Section 5 of the tender. The decision of Engineer regarding reduced rate shall be final & binding.
-
-
-
(5) In case of non performance of work at any or all locations, no payment shall be made and recovery shall be made for the measured area of non performance as per the quoted rate per sqm.
-
-
-
General cleaning and making the public toilet fit for use by satisfactorily cleaning of all types of dado, walls, floors, sanitary fitments like Indian water closet, European water closet, urinals, wash basins, marble or other type of urinal partitions, flushing units, mirror etc. either individually or in combination at all level including cleaning of bath zone with or without internal lobby by using available water, available cleansing agent like Harpik or Domex and other approved cleansing agent, available brooms, soft nylon brushes, rubbing papers but excluding necessary safety kit, ladder etc including sprinkliling of available phenyl, placing of available phynapthelene balls etc complete as directed by the Engineer-in-charge.
4000
-
-
This item shall be operated for second and onward frequencies of the day and the payment for FIRST frequency shall be payable under item no 6
-
-
-
Note: (1) Floor area of WC & Urinal portion of toilet shall be measured for payment.Dado,skirting and all types of fitments in this region shall be deemed to be covered up in the quoted rate. No payment shall be made for partially complete/incomplete work. The portion of toilet other than WC & Urinal region shall be measured under the item of general cleaning i.e. item no 5.
-
-
-
(2) The cost of labour, safety kits, uniform, ladder & brooms, soft brushes etc. shall be deemed to be included in the quoted rate. All cleansing agents,phenyl, phynapthelene balls etc, if & when required shall be made available by the department free of charge to the contractor at work place .
-
-
-
(3) The choking if any not caused due to fault of contractor and existed prior to taking up of cleaning operations shall be paid separately under relevant item as the same is not included in this item. However choking if any which was not existing prior to taking up of cleaning operations shall be considered as choking caused due to fault of contractor and removal of the same shall have to be borne by the contractor for which payment shall not be admissible.
-
-
-
(4) In case of unsatisfactory quality of work, reduced rate shall be applied as per clause 16 of Section 5 of the tender. The decision of Engineer regarding reduced rate shall be final & binding.
-
-
-
(5) In case of non performance of work at any or all locations no payment shall be made for non performed work and penalty shall also be levied for the measured area of non performance as per the quoted rate.
-
-
-
Cleaning and washing of sewer lines, inspection chambers, man holes etc.including clearing the blockages, if any in the lines by hiring and deploying hydraulic pressuring unit mounted on trucks applying the required water pressure to ensure easy flow of sewage/waste water etc and pumping out the sewage with hose and collected in a carrier for further disposal in oxidation pond etc complete as per specifications and as directed by Engineer-in-charge.
2
-
-
Note: 1) Measurement shall be taken on per job basis. This item shall be applicable for cleaning of medium size septic tank also.
-
-
-
(2) In case of unsatisfactory quality of work, reduced rate shall be applied as per clause 16 of Section 5 of the tender. The decision of Engineer regarding reduced rate shall be final & binding.
-
-
-
(3) In case of non performance of work at any or all locations, no payment shall be made and recovery shall be made for the measured area of non performance as per the quoted rate per job.
-
-
-
Cleaning the rain water pipe of all size, shape ,length 2.50m to 10.00m and corresponding terrace areas including removing the blockages if any by rodding and testing the same by pouring water etc.including opening & closing of C I door tees etc.complete as per drawing, specifications and as directed by Engineer-in-charge.
27
-
-
Note:(1) In case of unsatisfactory quality of work, reduced rate shall be applied as per clause 16 of Section 5 of the tender. The decision of Engineer regarding reduced rate shall be final & binding.
-
-
-
(2) In case of non performance of work at any or all locations, no payment shall be made and recovery shall be made for the measured area of non performance as per the quoted rate per pipe.
-
-
-
Cleaning the plastered normal masonry storm water drains (depth up to 1.2 mtrs) including removing the debris, grit etc and disposing off the same in pits within a lead of 250 mtrs, including cost of all tools and tackles etc.complete as per specifications and as directed by Engineer-in-charge.
220
-
-
Note:(1) In case of unsatisfactory quality of work, reduced rate shall be applied as per clause 16 of Section 5 of the tender. The decision of Engineer regarding reduced rate shall be final & binding.
-
-
-
(2) In case of non performance of work at any or all locations, no payment shall be made and recovery shall be made for the measured area of non performance as per the quoted rate per running metre.
-
-
-
Cleaning the earthen drains (Having bottom width of approx 500mm and depth varying from 0.50 M to 3.00 M), including excavation for trimming the sides and bottom in slope to allow for easy flow of rain water, removing the debris, grit etc and disposing off the same in pits within a lead of 100 mtrs, including cost of all tools and tackles etc.complete as per specifications and as directed by Engineer-in-charge.
15
-
-
Note:(1) In case of unsatisfactory quality of work, reduced rate shall be applied as per clause 16 of Section 5 of the tender. The decision of Engineer regarding reduced rate shall be final & binding.
-
-
-
(2) In case of non performance of work at any or all locations, no payment shall be made and recovery shall be made for the measured area of non performance as per the quoted rate per running metre.
-
-
-
Cleaning the storm water pipe outlets of all size, shape ,length located below footpath or area beyond road kerbs including removing the blockages if any by rodding and testing the same by pouring water etc.including digging ditch, if required for a length not exceeding 3.00 for free flow of water etc complete as directed by Engineer-in-charge.
12
-
-
Note:(1) In case of unsatisfactory quality of work, reduced rate shall be applied as per clause 16 of Section 5 of the tender. The decision of Engineer regarding reduced rate shall be final & binding.
-
-
-
(2) In case of non performance of work at any or all locations, no payment shall be made and recovery shall be made for the measured area of non performance as per the quoted rate per pipe.
-
-
-
Disposing debris, non value scrap, garbage, heaps of earth, rublles,rotton wood logs and the like by deploying excavator with Operator and Khalasi including collecting the same in a tractor with driver and Khalasi for conveying the same to low lying areas including deploying labourers for unloading the material from tractor, levelling and dressing the ground at both the places i.e. at lifting point as well as at point of disposal so as to carry out the assigned work any where in ARPF premises including the cost of all required tools & tackles, hire charges,fuel,necessary safety kit etc. complete as directed by the Engineer-in-charge.
2
-
-
Note: (1) The payment shall be made for the hours of work performed by the excavator at ARPF's site. The time at which the excavator arrives and starts at site and shuts down shall be noted for payment purposes.
-
-
-
(2)The cost incurred for deployment of labourers,excavator,tractor,ladders, safety kit etc,conveying arrangements, payment of all taxes, insurance etc shall be deemed to be included in the quoted rate.
-
-
-
(3) The contractor shall deploy as many number of labourers as required to ensure that work gets finished promptly.
-
-
-
(4) This item shall not be operated for items of dismantling works, earth work, area dressing, routine garbage disposal etc as the same is covered under respective items.
-
-
-
(5) In case of unsatisfactory quality of work, reduced rate shall be applied as per clause 16 of Section 5 of the tender. The decision of Engineer regarding reduced rate shall be final & binding.
-
-
-
(6) In case of non performance of work at any or all locations, no payment shall be made and recovery shall be made for the measured area of non performance as per the quoted rate per hour.
-
-
-
Disposing by mechanical transport ; the garbage consisting of debris, rubbish, packing boxes, grass etc. from ARPF building to the predetermined locations in the ARPF campus within 3 Km. lead including loading, unloading, levelling, carrying by mechanical transport as required to maintain cleanliness around offices, parks and buildings in ARPF campus including cost of all tools and tackles etc., complete as per specifications and as directed by Engineer-in-charge ( Carriage capacity shall be around 5.00 Cum.).
2
-
-
Making arrangement at all levels for catching rats using Rat Traps handed over by the department by keeping it at places which has high potential of movement of rats, preferably under the furniture or corner of walls including putting peanut butter and paste of flour for attracting rates ensuring its replacement on daily basis to avoid reinfestation including discharging the creature/rat at a distance of about 3.5 KM away in a non habitant locality including washing the trap as required etc complete as directed by the Engineer-in-charge.
200
-
-
Note 1) The payment shall be made per trap as one number. In case rat is not trapped and all activities are performed the quantity shall be considered as one fourth.
-
-
-
2) The cost incurred for deployment of labourers, tools & tackles, safety kit, all taxes etc shall be deemed to be included in the quoted rate. Rat trap shall be made available to the contractor free of cost.
-
-
-
3) In case of unsatisfactory quality of work, reduced rate shall be applied as per clause 16 of Section 5 of the tender. The decision of Engineer regarding reduced rate shall be final & binding.
-
-
-
4) In case of non performance of work at any or all locations,no payment shall be made and recovery shall be made for non performance as per the quoted rate per no.
-
-
-
Supplying and filling 100 ml liquid soap like Lifebuoy hand wash or Dettol or Sevlon in the existing soap dispenser installed near wash basins at discrete locations at all levels including emptying the residual liquid, rinsing and washing prior to re-filling, disposing the empty refill pack complete as directed by Engineer in Charge.
500
-
-
Note 1) The payment shall be as one number if entire 100 ml content is filled. In case of partial filling payment shall be made on proportionate basis based on actual quantity filled.
-
-
-
2) The cost incurred for deployment of labourers, tools & tackles, safety kit, all taxes, approved liquid soap etc shall be deemed to be included in the quoted rate.
-
-
-
3) In case of unsatisfactory quality of work, reduced rate shall be applied as per clause 16 of Section 5 of the tender. The decision of Engineer regarding reduced rate shall be final & binding.
-
-
-
4) In case of non performance of work at any or all locations, no payment shall be made and recovery shall be made for non performance as per the quoted rate per no.
-
-
-
Special housekeeping work in congested and sensitive equipment area by cleaning,sweeping,mopping,dusting,swabbing of floors, cleaning gently with exceptional care, the dust accumulated on equipments by using light duty vacuum cleaner including cleaning of doors/windows/ wall/ceiling surface complete as directed including the cost of all cosmetic materials, required tools & tackles, hire charges of vacuum cleaner, necessary safety kit, uniform, including the cost of soft nylon brushes and consumables like cleansing agent such as Harpic or Domex or Homex or other approved agent, phenyl, rubbing papers etc. complete as directed by the Engineer-in-charge.
500
-
-
Note: (1) Only floor area of the building shall be measured for payment of entire activities.
-
-
-
(2) The cost incurred for deployment of labourers, vacuum cleaners,ladders,safety kit, Uniform, Soft nylon brushes, buckets, all consumables like cleansing agent such as Harpik or Domex or other approved agent, phenyl, rubbing papers and all other cosmetic materials, all taxes etc shall be deemed to be included in the quoted rate.
-
-
-
(3) The contractor shall deploy only such qualified cosmetic helpers who have experience of carrying out work in such areas. Contractor shall deploy required number of personnel along with a supervisor to ensure that various jobs in whole area of the building gets finished very carefully in one working day.
-
-
-
(4) In case of unsatisfactory quality of work, reduced rate shall be applied as per clause 16 of Section 5 of the tender. The decision of Engineer regarding reduced rate shall be final & binding.
-
-
-
(5) In case of non performance of work at any or all locations, no payment shall be made and recovery shall be made for the measured area of non performance as per the quoted rate per sqm.
-
-
-
Cleaning & disinfecting of R C C overhead storage tanks of overall capacity 20000 litre to 25000 litre distributed in two compartments separated by RCC partition wall located on top of roof slab at a height ranging from 5.00 metre to 12.00 metre levels using bleaching powder @ 1 kg each tank including emptying the balance water in the tank below outlet etc , cleaning the tank by applying gentle acid,brooming,brushing and rinsing with bleaching powder safely without causing damage to waterproofing treatment including rinsing thrice with plain water including removing covers and the float valve with ball carefully prior to cleaning operation and refixing the same including removing the sediments if any ,other necessary activities like inspecting the existing M S ladder prior to use, tools & tackles, necessary safety appliances all as per specifications and as directed by the Engineer-in- Charge.
2
-
-
Note: (1) Any damage to cover and/or float valve with or without ball shall be replaced by the contractor at his own cost.
-
-
-
(2) In order to avoid suffocation of workers, contractor must ensure that workers must come out at regular interval to breathe in fresh air.
-
-
-
(3) In case of unsatisfactory quality of work, reduced rate shall be applied as per clause 16 of Section 5 of the tender. The decision of Engineer regarding reduced rate shall be final & binding.
-
-
-
(4) In case of non performance of work at any or all locations, no payment shall be made and recovery shall be made for the non performance as per the quoted rate per no.
-
-
-
Cleaning & disinfecting of R C C underground sumps of capacity ranging from 90000 litre to 100000 litre and depth around 3.00 metre using bleaching powder @ 1.80 kg each tank including emptying the balance water, if any in the tank , cleaning the tank by applying gentle acid,brooming,brushing safely without causing damage to waterproofing treatment including rinsing with bleaching powder followed by rinsing thrice with plain water including removing covers and the float valve with ball carefully prior to cleaning operation and refixing the same including removing the sediments if any etc complete including necessary activities like inspecting the existing M S ladder prior to use, tools & tackles, necessary safety appliances, masks all as per specifications and as directed by the Engineer-in- Charge.
2
-
-
Note: (1) Any damage to cover and/or float valve with or without ball shall be replaced by the contractor at his own cost.
-
-
-
(2) In order to avoid suffocation of workers, contractor must ensure that workers must come out at regular interval to breathe in fresh air.
-
-
-
(3) In case of unsatisfactory quality of work, reduced rate shall be applied as per clause 16 of Section 5 of the tender. The decision of Engineer regarding reduced rate shall be final & binding.
-
-
-
(4) In case of non performance of work at any or all locations, no payment shall be made and recovery shall be made for the non performance as per the quoted rate per no.
-
-
-
Management of receipt and distribution of Narmada water as well as tube well water in ARPF complex by deploying ITI (Fitter/Plumbing trade) trained operator or highly experienced operator daily in close consultation with the engineer of RRCAT or his authorized representative including maintaining the log book, giving daily feed back about the receipt of water, distribution of water either manually or through automation system including monitoring & operating Diesel Engine Pump set (make-Kirloskar) , Electric Pump set (Make: Kirloskar) on as & when required basis depending upon the supply timings of Narmada water supplied by Municipality and User's requirement by ensuring filling of sump as well as Overhead tanks basis without any interruption on all days in close consultation with the engineer and facility Users of RRCAT or their authorized representative including carrying out routine maintenance, oiling & greasing etc of ' pumps, supply & delivery valves float valves etc' including cost of labourers, supply & use of diesel for diesel pump (item continued in the next row),
12
-
-
minor CONSUMABLE items like welding electrodes/ fluxes, fastener sets, gaskets, minor fittings,sundris,transport of deployed staff to inspect daily, the dedicated CI line etc including maintaining the log book, giving daily feed back about the receipt & consumption of water, status of water line, fittings ,valves, pumps etc including carrying out MINOR repairs etc as & when required solely to ensure uninterrupted performance of the system etc all complete as per detailed specifications, standard operating procedures with total adherence to labour laws, contract conditions etc complete job as directed by Engineer in Charge .
-
-
-
Note: 1) The payment shall be based on calendar month whether it is of 31 days or less than 31 days for the entire job carried out as per detailed specifications.
-
-
-
2) Contractor shall take all necessary measures including training if any, minor maintenance of pumps, valves etc as required at his cost to assure uninterrupted performance. Specialized maintenance of pumps, valves etc is not in the scope of this item.
-
-
-
3) Engineer shall have right to disallow any workmen to work without assigning any reason whatsoever.
-
-
-
4) The contractor shall follow up with the officials of RRCAT Security, Civil maintenance cell, Facility Users, Municipality authorities etc as frequently as required to ensure uninterrupted water supply for functional utility.
-
-
-
5) The cost of deploying all labourers, minor materials,consumables,wastage,idle hour, tools, tackles, general safety gadgets, uniform, all applicable taxes including GST (Goods & Service tax), Corporation tax, Income tax, VAT, Labour cess , TDS on GST/Income tax, all other liabilities as per Contract Labour Act including those stipulated under clause 19 of section 4,section 8 & section 9 of the tender shall be entirely borne by the contractor and nothing on account of all these is admissible as the same is deemed to be included in the quoted rates.
-
-
-
6) In case of unsatisfactory quality of work, reduced rate shall be applied as per clause 16 of Section 5 of the tender. The decision of Engineer regarding reduced rate shall be final & binding.
-
-
-
7) In case of non performance of work at any or all locations, no payment shall be made and unpaid work shall attract recovery for non performance as per the quoted rate on prorata days basis.
-
-
-
Earthwork excavation in foundations in all soils other than soft and hard rock up to a depth specified below, including shoring and dewatering, if necessary, and refilling around foundations and plinth with selected excavated earth, in layers not exceeding 250mm thick, watering, consolidating etc., and disposing of surplus earth within a distance of 50 metre as per drawings, specifications and as directed by the Engineer-in-charge (depth of excavation shall be measured from the existing average ground level after over area excavation).
-
-
-
0.00 metre to 1.50 metre below average G.L
5
-
-
Excavation in trenches for pipes & sewers in all soils except soft & hard rock up to a depth of 1.50m including shoring & dewatering and refilling in trenches with selected excavated materials in layers not exceeding 250mm, consolidation and disposing surplus material within a distance of 50m etc. complete as directed by Engineer-in-Charge.
5
-
-
Lead charges by mechanical transport for lead exceeding 2 Kms but not exceeding 3 Kms including loading, unloading, stacking, levelling etc.
-
-
-
All soils
10
-
-
Demolishing brick work in cement mortar including scaffolding, stacking of serviceable material and disposal of unserviceable material within 50 mtr. lead as per drawings, specifications and as directed by the Engineer-in-Charge.
5
-
-
Dismantling the mosaic tile/white glazed tile/kotah stone etc. in flooring/dado/skirting etc. including, dismantling of bedding mortar, stacking of materials within 50 mtr. lead and disposing of debris within 50 m lead as per drawings, specifications and as directed by the Engineer- in-charge
5
-
-
Demolishing RCC/RB works by chiselling at all levels including scaffolding, including cutting of reinforcement bars but including disposal of all unserviceable materials within 50 mtr. lead all complete as per drawings, specifications and as directed by the Engineer-in-Charge.
0.5
-
-
Cutting holes up to 30 cm x 30 cm size in 240 mm thick plastered brick wall in cement mortar including scaffolding, disposal of unserviceable material within 50 mtr. lead and making good the wall with 20 mm thick,1:4 cement plaster, curing etc complete as per drawings, specifications and as directed by the Engineer-in-Charge
5
-
-
Cement concrete 1:3:6 using graded stone aggregates 40mm max. size including hand mixing, consolidation, finishing, curing and excluding centering etc complete as per drawing, specification and as directed by Engineer-in-Charge
3
-
-
REINFORCED cement concrete at all levels in M-20 grade using graded stone aggregate of 20 mm max. size including machine mixing, consolidation, finishing, curing, etc., complete at all height as per drawings, specifications and as directed by Engineer-in-charge but excluding shuttering, formwork and steel reinforcement.
-
-
-
In foundations, footing, plinth beams, window sills, base of columns,pathway,flooring etc.
1
-
-
REINFORCEMENT with HIGH YEILD STRENGTH DEFORMED BARS (TMT BARS) of grade Fe 500 confirming to IS 1786 for reinforced cement concrete work at all levels, including cutting, bending, fixing, tieing in position with 1.6 mm dia. soft drawn annealed binding wire, with chairs, legs, supports etc. complete including cost of transportation and binding wire, as per drawing, specifications and as directed by Engineer-in-charge.
-
-
-
Up to & inclusive of 16mm dia. Using TMT bars
0.1
-
-
Note : 1.BINDING WIRE required for the work will have to be supplied by the contractor at their own cost and will not be measured for payment.
-
-
-
2. The TMT bars Kamdhenu,Annant,Sardar, Magnum,Rathi or Goyal shall be arranged by the contractor.
-
-
-
Providing centering and shuttering at all heights using timber planks/steel plates including strutting and propping etc. and removal of the same for in situ reinforced concrete and in plain concrete work as per drawings, specifications and as directed by Engineer-in-charge.
-
-
-
Foundations, footings, base of columns, plinth beams, flooring, machine foundations, bed blocks, windows cills, copings and mass concrete.
4
-
-
Brickwork in CM 1:6 using IInd class bricks in drains & compound walls including curing, racking out joints above ground level & flush pointing below ground level etc. complete as per drawing, specification and as directed by Engineer-in-Charge
5
-
-
Cement plastering to internal /external surfaces of walls up to height of 10m, 20 mm thick in two coats, backing coat 15mm thick with cement mortar 1:4, 2nd coat 5mm thick in cement mortar 1:4 and finishing with neat cement punning over brick walls or concrete surfaces, including hacking the concrete surfaces, double scaffolding wherever necessary, curing etc., complete as per drawings, specifications and as directed by the Engineer-in-charge.
10
-
-
Providing and laying polyvinyl (PVC) rolls/tiles manufactured by M/s. Premier/Responsive/Birla or other approved company of thickness 2mm heavy duty solid vinyl flooring ROBUST/TUSKER of approved colour, pattern and designs for flooring, skirting/dado laid on existing smooth cement tile or concrete or plastered finish, with suitable adhesive as per manufacturer's specifications, close jointed by PVC welding and finished to proper bends, slope and plumb etc. complete as directed by EIC.
10
-
-
Providing & laying Non Slippery Ceramic tile flooring/dado using 6mm thick matt finished ceramic tiles of sizes as mentioned below, 1st quality (SPARTEK /NITCO/BELL/KAJARIA/EURO or SOMANI brand of approved colour) over 20mm thick cement mortar 1:3 bedding, close jointed and pointed with matching cement slurry using white cement pigment mixed with, finished to levels slope or plumb as required including cutting of tiles, curing, acid washing etc. complete as per drawing, specifications and as directed by Engineer-in-charge.
-
-
-
In flooring using tiles of size 450 mm x 450 mm x 6 mm or 300 x 300 x 6 mm.
5
-
-
In dado using tiles of size 300 mm x 450 mm x 6 mm or 200 x 200 x 6 mm or 200 x 300 x 6 mm
10
-
-
Providing and fixing in position 9 mm thick first class vitrified porcelain tiles with marble/granite finish (Granite/Diamontile) of approved manufacturer of size 600mmx 600mm of approved color, pattern and design for flooring, skirting or dado laid in floor, wall of existing concrete or plastered surface over 20 mm thick cement mortar 1:3 bedding close jointed and pointed with matching slurry using white cement with pigments finished to levels, slope or plumb as required including cement mortar bedding, cutting of tiles to required size and curing, acid washing etc. complete.
10
-
-
Providing and laying/fixing in position 20mm thick machine polished granite slabs of approved colour and quality including machine/hand cut, polishing, buffing the edges all in line, level, (curvature corners if required) in cement mortar 1:3 with best workmanship, finishing, curing, complete in platforms, shelves, wash basin, cills, jambs, facias, treads and risers etc. complete.
-
-
-
Other than black shades
2.5
-
-
Providing and fixing 2mm thick epoxy based joint less flooring (Asian paints/Fosroc/Essen/Dr. Beck/STP) over existing flooring such as concrete floor, tiles, wood, metal etc. formulated out to required levels, thickness slopes and finished smooth or rough including curing, preparing the surfaces such as filling holes, cracks, joints, wherever necessary by epoxy based trowelling compound, including providing and applying one coat of two component epoxy based primer including cost of materials and labours etc. complete as per manufacturer's recommendation.
10
-
-
Preparing the surface and etching with 10% commercial hydrochloric acid wherever necessary, neutralizing the etched areas by washing with 5% solution of soda ash, applying one coat of pigmented epoxy based primer followed by one coat of epoxy based trowelling compound, cutting and grinding the surfaces wherever necessary using waterproof quality emery paper and applying three finishing coats of epoxy based polyamide cured special acid and alkali resistant paint of approved make & tint including preparing surfaces, scrapping, filling holes, cracks, joints, wherever necessary with epoxy based trowelling compound, cost of all materials, scaffolding and labour and as per manufacturer's recommendations.
25
-
-
Painting plastered surfaces with two finishing coats of Acrylic emulsion paint of approved shade and make, over one coat of approved cement primer including preparing the surfaces, filling with full wall putty, scaffolding and cleaning etc. complete as directed by EIC
75
-
-
Painting the old exterior walls and roof with two coats of Snowcryl XT acrylic emulsion/APEX Ultima of approved shade including preparing the surface by removing loose dust and dirt with stiff brush and washing the surface with clean water, treating the surface with antifungal chemical wherever required, filling with putty, scaffolding and cleaning etc. complete. as directed by EIC.
75
-
-
Supplying, lowering, laying, RCC spun pipes (Class NP2) of IS : 458 with necessary collars, laid to correct grade and levels at all depths including cutting to length, jointing with hemp yarn and C.M. 1:1, caulking the joints and finishing, curing, testing etc. complete as directed by EIC.
-
-
-
150 mm dia
2
-
-
300 mm dia
4
-
-
Providing, laying, jointing, fixing, testing and painting in 2 coats anticorrosive bituminous paint for concealed portion and oil paint for exposed portion of pipes (Class ‘C’) as per I.S. 1239-1979 (ISI mark with number inscribed on surface) heavy variety M.S. galvanized pipes of Prakash, Surya or Jindal with sockets also all as per the code of practice of water supply in building of IS: 2065-1972 complete INCLUDING fittings,specials,flanges,screwed flanges conforming to IS: 1239-1979 (ISI mark with number inscribed on surface) etc which are covered under different items but including testing the pipes and fittings for 10 kg/cm2 pressure with a minimum period of 2 hrs. duration, including laying under the floors, chasing in walls, roof slabs and making good the same to the original conditions, including cost of all jointing material like hemp yarn, white or red lead, clamps, wooden gutties, screws, cement, sand etc. complete as per drawing, specifications and as directed by the Engineer-in-Charge.
-
-
-
15mm n.b
3
-
-
20mm n.b.
3
-
-
25mm n.b.
3
-
-
32mm n.b.
3
-
-
40mm n.b.
3
-
-
50mm n.b.
3
-
-
Note: The measurement shall be taken along centre line of pipes and fittings or specials, excluding flanges. Contractor shall assume one fitting per metre length of pipe to quote the rate.
-
-
-
Note: Flanges and fittings beyond above limit not shown in the tender drawing shall be paid under relevant item.
-
-
-
Providing & fixing in position heavy pattern screwed down gun metal GATE VALVES Sant or Leader or Kirloskar brand conforming to ISI: 778-1964 (ISI mark with number inscribed on surface) with hand wheels at top including testing for 10kg/cm2 pressure with clean and potable water with a minimum testing duration of two hours etc. complete as per specifications and as directed by the Engineer-in-Charge.
-
-
-
15 mm n.b.
1
-
-
20mm n.b.
1
-
-
25mm n.b
1
-
-
32mm n.b.
1
-
-
40mm n.b
1
-
-
50mm n.b.
1
-
-
Providing, laying or fixing in position under floors against walls centrifugally cast (spun) iron or sand cast iron socket and spigot soil, waste, ventilation pipes and fittings, including cost of all fittings like bends, offsets, tees, tapers, collars, connectors, plugs, shoes, etc. conforming to IS: 3989-1970(ISI mark with number inscribed on surface) and IS: 1729-1964 (ISI mark with number inscribed on surface) respectively, including cost of jointing with tarred spun (jute) yarn and molten pig lead, caulking the joints including testing, painting with two coats of approved paint over a coat of primer etc. complete as per specifications and as directed by Engineer-in-charge.
-
-
-
75 mm dia ( with 0.90 kg lead/joint)
2
-
-
100 mm dia ( with 1.00 kg lead/joint)
2
-
-
Providing and fixing CI/ HDPE/PVC rigid FLOOR trap of self cleaning design with 75mm/100mm outlet having a minimum water seal of 50mm with C.P. brass/stainless steel grating on top including necessary 1:2:4 cement concrete for embedding trap etc., complete conforming to IS 3989-1970(ISI mark with number inscribed on surface) as per drawing, specifications and as directed by the Engineer-in-Charge.
1
-
-
Providing and fixing heavy quality C.P. brass screw down 15mm n.b STOP COCKS/ Angle cock conforming to I S 8931 of Plumber (heavy) or Jaquar make on G.I. lines, complete as per drawing, specifications and as directed by the Engineer-in-Charge.
1
-
-
Providing and fixing 15mm n.b. quarter turn fancy variety heavy quality C.P. brass two way angle cock (Plumber- UT-2155/ Jaquar make) conforming to IS : 781. complete as per drawing, specifications and as directed by the Engineer-in-Charge.
1
-
-
Providing & fixing 15mm dia heavy quality C.P. brass screw down BIB TAPS of Jaquar or Plumber (heavy) make conforming to IS-781 on G.I. lines, complete as per drawing, specifications and as directed by the Engineer-in-Charge.
1
-
-
Providing & fixing approved make heavy quality C. P. brass screw down PILLAR TAP with jam nut, of 15mm n.b.of Jaquar or Plumber (heavy) make conforming to I.S. 1795, as per specifications and as directed by Engineer-in-charge.
1
-
-
Providing and fixing Commander make heavy quality solid PLASTIC SEAT (for EWC pan) with lid of approved make and colour with C.P brass pillar hinges etc., complete conforming to IS :2548 (Part I and II) and as per specifications and as directed by Engineer-In-Charge.
1
-
-
Filling the joints of floor tiles, dado tiles, the joint between floor & dado and the joint between WC & floor etc. using matching cement with suitable fast setting compound etc complete as directed by Engineer-in-charge. Note: The payment shall be made for floor/dado area treated as above without making deduction of area occupied by WC
50
-
-
Providing & fixing in position finished C.P. brass coat hangers (Plumber- Robe hook twin- UF 0915 or Jaquar 35791) satin finish with nettle fold screws etc. complete as per drawings, specifications and as directed and approved by Engineer-in-Charge.
1
-
-
Providing and fixing recessed type TOILET PAPER ROLL HOLDER of Parryware (C 9950) or equivalent make in coloured glazed vitreous chinaware including cutting into wall, making good the same complete as per specifications and as directed by Engineer-in-charge.
1
-
-
Providing & fixing heavy quality approved make 15mm n.b. screw down type C.P. brass or brass oxidised SWAN NECK THREE WAY TAP of easy clean variety with jam nut etc. as per drawing, specifications & as directed by Engineer-in-Charge
1
-
-
Attending to non measurable,labour intensive plumbing /sanitary routine repair jobs executable by deploying a skilled plumber and/or plumbing helper etc complete as directed by Engineer-in-charge.
-
-
-
Skilled Plumber/Mason/carpenter
25
-
-
Unskilled helper
250
-
-
Note :- (1) Material required for taking up repairs shall be provided by the Department.(2) All liabilities as per contract labour act 1970/1971,Building & construction workers act 1996 and all taxes shall be deemed to be included in the quoted rate for full day deployment.(3) The tools, Safety kit etc shall be provided by the contractor and shall bear all costs on account of this including those of wear & tear etc.
-
-
-
Servicing of ELECTRICALLY OPERATED rolling shutters with or without wicket gates by dismantling for overhauling of individual parts for repairs and after repairs i.e. top hood shaft cage, shaft brackets, springs, main curtain with lathe or mid bar type grills, wicket gate, side guides, bottom rails, gear units, bearings, electric motors, starters and thoroughly cleaning all the components, adjusting and tensioning springs, if needed, overhauling or repairing shaft and gear units, reconditioning end clips, realigning curtain ends, reconditioning dents, if any on the surface of curtain, bottom rail and side guides, repairing the starter, inspecting, taking out and replacing the damaged or defective components (replacement of part at quoted rate is payable separately under relevant item), ensuring proper locking arrangements, from both inside and outside including all welding, drilling, straightening, grinding, scaffolding, ladders, tools, tackles, with all consumables such as lubricants, white kerosene, grease etc. and small screws, washers, keys etc. making good any damages to civil works, cleaning the area by disposing off scraps, debris etc, oiling, greasing and demonstrating proper functioning of the shutters after such service etc. complete as directed by Engineer-in-charge.
30
-
-
Servicing of Emergency exit doors by dismantling for overhauling of individual parts associated with operation of door including cleaning of materials causing door jam, removing the rust scales by sand papering, servicing of spindle & calm arrangement, inspecting, taking out and replacing the damaged or defective or worn out nut, bolts, washers or rivets as required including all welding, drilling, straightening, grinding, scaffolding, ladders, tools, tackles, with all consumables such as lubricants kerosene, grease, rivets, washers etc. making good any damages to civil works, cleaning the area by disposing off scraps, debris etc, oiling, greasing and demonstrating proper functioning of the door after such service etc. complete as directed by Engineer-in-charge.
3
-
-
Servicing of Collapsible doors or sliding type of grill gates by dismantling for overhauling of individual parts associated with smooth sliding action, cleaning of track to remove all type of waste, dusts etc, removing the rust scales by sand papering, reasonably tightening of rivets by spot hammer press, inspecting, taking out and replacing the damaged or defective or worn out nut, bolts, washers or rivets, as required including all welding, drilling, straightening, grinding, scaffolding, ladders, tools, tackles, with all consumables such as lubricants kerosene, grease, rivets, washers etc. making good any damages to civil works, cleaning the area by disposing off scraps, debris etc, oiling, greasing and demonstrating proper functioning of the door/gate after such service etc. complete as directed by Engineer-in-charge.
15
-
-
Repainting of old painted surfaces with two coats of paint of approved shade & made like Asian paints, Goodlas Nerolac OR ICI including preparing the surfaces, including removal of old paint, if any, sand papering, filling hair cracks with putty and other cracks with 'Roffe' repair mortar as required, scaffolding & cleaning, cost of all materials, labour, all complete as per drawing, specifications and as directed by Engineer-in-charge. Note : Plaster of paris putty required for filling work in walls shall be of standard brands such as Terraco, Gypsum India Ltd.
-
-
-
Using Synthetic enamel paint
45
-
-
Providing & fixing Aluminium glazing clip for fixing the glasses in door/window shutters including cutting the clip in size, removing the existing worn out clip etc complete as per specifications and as directed by the Engineer-in-Charge.
10
-
-
Providing & fixing 2 mm thick Aluminium glazing plate of height about 50mm with appropriate grooves for holding & fixing the glasses in door/window shutters including cutting the plate in size, removing the existing worn out plate etc complete as per specifications and as directed by the Engineer-in-Charge.
5
-
-
Providing and fixing in position up to & including 6.00 metre height from adjoining ground level Bajra or Plain & clear Sheet glass/Float glass/Wired glass of Modiguard, Asahi, Atul or Saint Gobin make and of following thickness fixed to Aluminum/M.S. windows, doors, partitions, ventilators etc. with edges champhered (wherever required) with PVC/Neoprene Gasket or rubber lining as required etc all complete as per drawing and specifications and as directed by the Engineer-in-Charge.
-
-
-
3.50 mm thick Bajra glass
10
-
-
4 mm thick Plain glass
5
-
-
5 mm thick Plain glass
5
-
-
6 mm thick Plain glass
2
-
-
Note : (1) Only the clear opening of Glass shall be measured for payment. Aluminum snap beading shall be measured and paid separately under relevant item.
-
-
-
Note : (2) Broken glass pieces shall be disposed off in a safe manner to a place as directed.
-
-
-
Note : (3) Temporary scaffolding shall be paid extra under relevant item if the bottom level of glass is located at 6.00 metre height above adjoining ground level.
-
-
-
Providing and fixing at all heights Bajra glass louvers 3.5 mm thick, in grooves of window frames complete as per specifications and as directed by Engineer in Charge. Note: Measurement will be based on area of louvered window. In case of composite windows, area shall be measures as internal area of louvered portion.
2
-
-
Note: Measurement will be based on area of louvered window. In case of composite windows, area shall be measures as internal area of louvered portion.
-
-
-
Providing and fixing in position Aluminum partitions, doors, windows, ventilators, louvers, fixed glazing, sliding windows, north light glazing, aluminum rough ground etc. with extruded and anodized (15 microns) to natural aluminum/Metallic colour, aluminum Sections, anodized aluminum beadings, anodized aluminum Sheets manufactured to relevant IS codes and using minimum 2mm thick (or as specified) heavy sections INDAL/JINDAL/MAN or approved equivalent make including cost of pivots, approved door and window handles, EPDM gasket, PVC/Neoprene Gasket lining, stainless steel screws, mastic filling, weather strips, tower bolts, nuts, washers etc. as required and as per drawing etc. complete as directed by the Engineer-in-charge..
20
-
-
Note: 1. Payment will be made on the basis of weight of Aluminum members/sections fabricated and actually installed in position without extra allowance for wastage. No extra payment will be made for all non-aluminum consumable items like screws, gasket, weather strips, PVC/Neoprene lining and butt hinges, tower bolts, etc.
-
-
-
2. Glazing, particle boards, aluminum grills, mesh etc. will be measured and paid separately under relevant item.
-
-
-
3. All fittings shall be of matching colour anodized aluminum Sections.
-
-
-
4. The Aluminum Sections shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angles at no extra cost.
-
-
-
Providing and fixing heavy duty Locking arrangements for sliding windows using STAR LOCK or MID-IN or Maruti make of size 85 mm ± 10 mm, including built in heavy duty plated M.S. spring, necessary screws, all materials, labourers etc. complete as directed by the Engineer-in-charge.
2
-
-
Providing & fixing anodized Aluminum Beading of size 9.5 mm x 9.5 mm for fixing glass for steel windows with necessary screws etc. complete as directed by the Engineer-in-charge.
10
-
-
Providing & fixing rubber lining for fixing glass for steel / aluminium windows with necessary screws etc. complete as directed by the Engineer-in-charge.
10
-
-
Providing and fixing sleek Model heavy duty Hydraulic Door Closer Godrej / Hardwyn make with necessary screws, fixing to the aluminium/wooden/M.S. doors complete as per drawing, specifications including all labour, transporting etc. and as directed by the Engineer-in-charge. Note:- Tax paid bill showing warranty period shall be submitted by the contractor.
3
-
-
Providing and fixing sleek Model heavy duty Hydraulic Door Closer of Dorma make conforming to IS 1564 with necessary screws & accessories, fixing to the Aluminium/Wooden/M.S.doors complete as per drawing, specifications including all labour, transporting etc. and as directed by the Engineer-in-charge. Note:- Tax paid bill showing warranty period shall be submitted by the contractor.
1
-
-
Providing & fixing in position at all heights Novapan or ECO board, 12 mm thick both side pre-laminated particle board of exterior grade I / Type II conforming to I S 12823, bonded with Phenol Formaldehyde resin in partitions/doors using approved standard Aluminium beading including cost of screws, cost for cutting to required sizes, wastages, fixing to existing frame with nut/bolts/screws as required including necessary incidental charges for ensuring its position, proper line & level etc all complete as per drawing and specifications and as directed by the Engineer-in-Charge.
10
-
-
Note : Aluminum frame work and Aluminum Snap beading used for fixing boards shall be measured and paid for separately under relevant item.
-
-
-
Providing & fixing locally fabricated 100 mm x 20 mm x 3 mm brass plate with suitable recess to accommodate 12.5 mm dia stainless steel ball bearing for easy movement of Aluminium Shutter fixed at top or bottom of Aluminium Shutter after removing aluminium door shutter & the same after positioning the ball based pivot including making holes in frame, cost of necessary hardware etc. complete as per specifications and as directed by the Engineer-in-Charge.
2
-
-
Providing & fixing locally available best quality 400 mm long concealed type Aluminium vertical tower bolt in an existing Aluminium door after removing aluminium door shutter & the same after positioning the concealed type tower bolt including cost of necessary hardware etc. complete as per specifications and as directed by the Engineer-in-Charge.
2
-
-
Providing & fixing best quality pin type pivotal assembly of Everite or Garnish or Hyper or Godrej or Dorma make, for easy movement of Aluminium shutter fixed at top or bottom of Aluminium Shutter after removing aluminium door shutter & the same after positioning the pivot assembly including making holes in frame, cost of necessary hardware etc. complete as per specifications and as directed by the Engineer-in-Charge.
2
-
-
Providing & fixing push plate made of exterior grade water proof ply of 20mm thickness and 150mm high of required length including formica front & rear facing of 0.5 mm thick including providing & fixing Aluminium C Channel of size 25 mm x 25 mm x 1.5 mm on all edges of push plate for strengthening existing Aluminium doors, if required including removing aluminium door shutter, drilling holes for fixing screws, nut, bolts etc & the same after positioning the push plate including cost of necessary hardware etc. complete as per specifications and as directed by the Engineer-in-Charge.
2
-
-
Providing & fixing 15 micron anodized aluminium Section of MAN/ZINDAL or HINDALCO for top rail or bottom rail or lock rail of size 114.5 mm x 44.5 mm x 3 mm of required length in lieu of worn out/damaged member including removing aluminium door shutter, drilling holes for fixing screws, nut, bolts & fixing the new member and then the shutter, existing fixtures etc in position including cost of necessary hardware etc. complete as per specifications and as directed by the Engineer-in-Charge.
2
-
-
Servicing of single or double leaf Aluminium doors of size not exceeding 3.00 sqm including removing of door shutter from position, adjusting, aligning & servicing floor spring and the cover plate, realigning the door, oiling the pinion/ pin type pivot or ball type pivot, tightening of all screws nuts, bolts used for fixing of hinges, tower bolts, door closure, push plates, handles, beadings, glazing clips etc. to ensure smooth functioning of aluminium doors etc. all but excluding servicing of floor spring complete as per specifications and as directed by the Engineer-in-Charge.
10
-
-
Note: (1) Required bolts, nuts, screws, rivets and rubber gasket etc. shall be deemed to be included in the quoted rate for which nothing extra shall be paid.
-
-
-
(2) All other items like floor spring, Aluminium Sections, hydraulic door closure, hinges, concealed tower bolts, pinion/ pin type pivot, ball type pivot, tower bolts, glasses, particle boards as required shall be paid under relevant items.
-
-
-
(3) Replacement of floor spring if required shall be paid under relevant items.
-
-
-
Servicing of single or double leaf Aluminium doors of size exceeding 3.00 sqm including removing of door shutter from position, adjusting, aligning and servicing floor spring and re-fixing the cover plate, realigning the door, oiling the pinion/ pin type pivot or ball type pivot, tightening of all screws nuts, bolts used for fixing of hinges, tower bolts, door closure, push plates, handles, beadings, glazing clips etc. to ensure smooth functioning of aluminium doors etc. all but excluding servicing of floor spring complete as per specifications and as directed by the Engineer-in-Charge.
20
-
-
(2) All other items like floor spring, Aluminium Sections, hydraulic door closure, hinges, concealed tower bolts, pinion/ pin type pivot, ball type pivot, tower bolts, glasses, particle boards as required shall be paid under relevant items.
-
-
-
(3) Replacement of floor spring if required shall be paid under relevant items.
-
-
-
Servicing of Glass doors of size up to 5.00 sqm including removing of door shutter from position, adjusting & aligning floor spring and re-fixing the cover plate, realigning the door, oiling and servicing the glass door hydraulic hinges / servicing of floor spring, tightening of all screws nuts, bolts used for fixing of hinges, push plates, handles etc. to ensure smooth functioning of glass doors etc. complete as per specifications and as directed by the Engineer-in-Charge.
5
-
-
Note: (1) Required bolts, nuts, screws, rivets and rubber gasket etc. shall be deemed to be included in the quoted rate for which nothing extra shall be paid.
-
-
-
(2) All other items like Aluminium / M.S.sections, hydraulic door hinges, glasses, as required shall be paid under relevant items.
-
-
-
(3) If the glass of door will be broken during servicing, the same will be replaced by the contractor at free of cost.
-
-
-
Welding of M.S. windows/doors or any other member of any size any-where in ARPF premises at all heights including scraping of existing worn out joint welding of joints using approved electrodes to achieve 3mm weld thickness of required weld length including removing flux, debris etc., painting one coat of steel primer touch up, grinding of joint before painting including safe removing & refixing of glass if necessary etc. complete as per drawing, specifications and as directed by Engineer-in-charge.
15
-
-
Extra for erecting steel scaffolding unit 10.00 metre high using vertical pipes made of 40 mm n b , M.S. pipe of 10 G thickness and horizontal pipes made of 40 mm n b , M.S. pipe of 20 G thickness, fixed vertically & horizontally at spacing not exceeding 1200 mm resting over base plate of size 100 mm x 100 mm x 6 mm below vertical pipes, diagonal bracings shall be made of 40 mm n b , M.S. pipe of 20 BG thickness, tying all junctions with standard M.S. couplers including providing & fixing sitting unit made of closely spaced Bamboo Challis, having approximately 40 mm thickness tying the whole unit with existing reliable supports ,safety barricades at working level dismantling the same as & when required including screws ,nails etc complete as per drawing, specifications and as directed by the Engineer-in-Charge. Note: Only Plan area shall be measured for payment. De-assembled scaffolding material shall remain contractor's property.
15
-
-
Note:1) Above item does not include the cost of glass panes. 2) Area of exposed glass shall be measured for payment purposes.
-
-
-
Providing & injecting weather silicon sealant of G E or Pidilite or STP or other similar silicon sealant for filling the gaps between window frame and adjacent "RCC work or Brick masonry or stone masonry or stone cladding or stone sill or plastered surfaces" after preparing the surface by removing loose materials if any, filling the excess gap with wooden chips, thermocole pieces etc so that net cross sectional dimension of gap ready for injection is around 5 mm x 5 mm complete including the cost of all materials, labour, safety kit ,injecting gun, tools, all taxes & levies etc. complete as per specifications and as directed by the Engineer-in-Charge.
90
-
-
Note: Scaffolding for work beyond ground floor shall be paid separately under item.
-
-
-
Providing and fixing ALUMIGRILL-AL - 102 (10mm) or DECOGRILL - DG-102 (10mm) to the windows, ventilators, wall span etc. in approved colour, anodizing (15 micron) to match with the colour of window frame from inside or outside etc. all complete as per drawing and as per the directions of the Engineer-in-Charge.
2
-
-
NOTE: Aluminium frame work and aluminium snap beading shall be used for fixing Grills shall be measured and paid under relevant item.
-
-
-
Collecting public drinking water samples or effluent water samples as directed, from scaterred locations in ARPF/RRCAT, carefully in containers disinfected as per I S 1622-1987 for arranging testing on specified parameters as per IS 3025 part 1 to 60 to ascertain suitability of water for intended use, complete as per following notes and as directed by the Engineer-in- Charge.
4
-
-
Note: (1) The contractor at his own cost need to deploy labourers to operate valves, taps, pump of tube wells to collect water samples from descrete locations anywhere in ARPF/RRCAT premises.Opening & refixing of fittings, if required, shall be carried out by the department only.
-
-
-
Note: (2) The contractor at his own cost shall get the water tested from M P Pollution Control Board Laboratory to ascertain pH, suspended solids,Total solids, chloride, Lead, Iron,Sulphate,BOD, COD, MPN,Dissolved Oxygen,Turbidity,Total hardness, Calcium Hardness,Magnesium Hardness etc.for drinking water and pH, suspended solids,,BOD,COD, MPN,Dissolved Oxygen,Total hardness,Calcium Hardness,Magnesium Hardness etc.for effluent water. Nothing extra shall be paid for submission of test results of additional parameters.
-
-
-
Note: (3) The contractor need to bear all expenditures for delivering the samples and later in obtaining test report from from M P Pollution Control Board Laboratory including safety kits, tools & tacles, testing charges, cost of container, arranging to & fro transport accompanying departmental representative from ARPF/RRCAT premises to & from M P Pollution Control Board Laboratory to assure authenticity of collected samples and safe handing over of the same in laboratory.
-
-
-
Providing pest control treatment to entire ARPF complex at all the floors in all the rooms, labs., toilets, WCs, bathrooms, halls, stores, passages etc. for controlling entry of rodents, lizards, cockroaches, ants, bugs etc. using chemicals Cyfluthrine, Fpronil Gel, Delta Matherine, Bhromodylene cake as required, Burofumigation with sulphas etc. complete as per manufacturers specifications & as directed by EIC. The treatment shall be done at monthly duration for total area 2500.00 Sqm. approx.
12
-
-
Note- (1) The treatment shall be guanteed for one month. It means during one month period no occurrence of rodents, lizards, cockroaches, ants, bugs etc . If occurred recovery shall be made for affected areas.
-
-
-
(2) During operations proper hygiene should be maintained. Special care shall be taken during /after the treatment in labs. & allied areas. Proper cleaning should be done after the treatment to remove the left over of chemicals.
-
-
-
(3) The area for one operation means for 2500.00 Sqm (approx.) area for every month duration.
-
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements