National Law Institute University Tender

Providing & laying PCC 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) for foundation and under floor including formwork.

Providing & laying RCC M-15 excluding cost of centering, shuttering and reinforcement but including mechanically mixing, vibrating, curing etc. complete at all depths, heights and levels . Foundations, rafts, pedestals, grade slab, plinth beams etc.

Providing & laying RCC M-15 excluding cost of centering, shuttering and reinforcement but including mechanically mixing, vibrating, curing etc. complete at all depths, heights and levels Columns, pillars, posts and struts , piers etc.

Providing & laying RCC M-15 excluding cost of centering, shuttering and reinforcement but including mechanically mixing, vibrating, curing etc. complete at all depths, heights and levels Beams of all shapes, lintels etc.

Providing & laying RCC M-15 excluding cost of centering, shuttering and reinforcement but including mechanically mixing, vibrating, curing etc. complete at all depths, heights and levels suspended floors, roof slabs, sloping roofs, landings, shelves, balconies, chajjas, bands etc.

Providing centering & shuttering including strutting and propping etc. and removal of formwork at all floors, depths, heights and shapes. Foundations, rafts, pedestals, grade slab, plinth beams etc.

Providing centering & shuttering including strutting and propping etc. and removal of formwork at all floors, depths, heights and shapes. Columns, pillars, posts and struts , piers etc.

Providing centering & shuttering including strutting and propping etc. and removal of formwork at all floors, depths, heights and shapes. Beams of all shapes, lintels etc.

Providing centering & shuttering including strutting and propping etc. and removal of formwork at all floors, depths, heights and shapes Suspended floors, roof slabs, sloping roofs, landings, shelves, balconies, chajjas, bands etc.

Providing and laying reinforce- ments high yield strength ribbed cold twisted Tor steel of various diameters grade FE 500 D conforming to IS code 1786 for reinforced concrete work including cutting, bending, binding with annealed 18G MS binding wire, placing in position according to drawings. (Rate shall include cost of binding wire, cover blocks, etc.

Providing and laying brick work with Ist class bricks in superstructure at all floors, levels and heights in cement mortar 1:6 (1 cement : 6 coarse sand). The rate shall include curing etc. complete.

Providing and laying Ceramic glazed floor tiles 300x300 mm or more (having thickness 6 to 7mm) of 1st quality conforming to IS : 15622 of approved make in any colours and shade laid on20 mm thick Cement Mortar 1:4 (1 Cement : 4 sand) including pointing the joints with white cement and matching pigment etc., complete. Ceramic tiles (as per manufacturer's specifications)

35 mm thick factory made Solid panel PVC Door shutter made out of single piece extruded soild PVC profiles, 5mm (±0.2mm) thick, having styles and rails (except lock rail) of size 95 mmx 35 mm x 5 mm, out of which 75 mm shall be flat and 20 mm shall be tapered (on both side), having one side thickness of 15 mm integrally extruded on the hinge side of the profile for better screw holding power, including reinforcing with MS tube of size 40 mm x 20 mm x 1 mm, joints of styles and rails to be mitered cut and joint with the help of PVC solvent cement, self driven self tapping screws and M.S. rectangular pipes bracket of size 190 mm x100 mm of cross section size 35 mm x 17 mm x 1 mm at each corner. Single piece extruded 5mm thick solid PVC Lock rail of size 115 mm x 35 mm x 35 mm, out of which 95 mm to be flat and 20 mm to be tapered at both ends, having 15 mm solid core in middle of rail section integrally extruded, fixing the styles and rails with the help of solvent and self driven self tapping screws of 125 mm x11 mm, including providing 5mm Single piece solid PVC extruded sheet inserted in the door as panel, all complete as per manufacturer's specification and direction of Engineer-in charge. Non decorative finish (matt finish).

Providing and Fixing, factory made, PVC door frame made of PVC extruded sections of size 75mmx53 mm, having wall thickness 2.0mm (±0.2mm). Both verticals sides of the frame reinforced with PVC profile of cross section size 28mm x 30mmx2mm thickness (± 0.2 mm) and 75mmx200 mm long, including reinforcing both ends of the top frame with PVC profile. PVC Door Frame and PVC reinforcement profile to be mitred cut jointed and fusion welded together, including providing andfixing 3 nos. of 125mm long stainless steel hinges to frame, fixing the frame with jamb with required nos. and sizes of anchor dash fastener, all complete as per manufacturer's specification and direction of engineer-in-charge including accessories & lock inf arrangement.

Providing & applying 15mm thick internal wall plaster in CM 1:6 ( 1 cement : 6 sand using 25% coarse sand and 75% fine sand) at all heights and levels including scaffolding, curing etc. complete.

Providing & applying 12mm thick plaster in CM 1:6 (1 cement : 6 coarse sand using 25% coarse sand and 75% fine sand) on ceiling including hacking the surface, scaffolding, curing etc. at all levels and heights etc.

Providing & applying 18mm thk external plaster in two coats under layer 12mm cement plaster 1:5 (1 cement : 5 coarse sand) and top layer 6mm thick cement plaster 1:4 (1 cement : 4 coarse sand) finished smooth including scaffolding and using admixture of approved make while plastering the junction of two different material such as RCC and brick etc.

Providing & applying three or more coats of white washing with lime, using DDL (of pidilite) binder as per manufacturers specifications, to ceilings and walls to give an even shade, on new work including surface preparation at all levels & heights.

Distempering by any mechanical or manual means with 1st quality acrylic distemper, having VOC (Volatile Organic Compound) content less than50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.

Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100mm sand cast Iron P or Strap, UPVC P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good thewalls and floors wherever required : White Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type foot rests.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer- in-Charge. 20 mm nominal outer dia .Pipes.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but with fittings and the base support for tank

Providing and fixing brass bib cock of approved quality 20 mm dia

Providing and laying below ground unplasticised PVC pipe to with stand working pressure of 4 kg/cm2 soild waste pipes confirming to IS:13592 and IS:4985 including jointing with seal ring confirming to IS :5282 leaving 10mm gap for thermal expansion all necessary fittings etc. complete. Excavation to be paid seperataly. 160 mm diameter OD (min. wall thickness 4.0mm)

Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre and post flushing with water ( 250 ml and 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-Charge.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Flat back wash basin size 450x300 mm with single 15 mm C.P. brass pillar tap.

Providing and fixing soil, waste and vent pipes: Sand cast iron socket and spigot (S&S) pipe as per IS: 1729 100 mm dia with wall thickness of 5 mm

Providing and fixing PTMT grating of approved quality and colour. Circular type. 125 mm nominal dia with 25 mm waste hole

Providing and applying waterproofing & Heat reflecting roof coating with 100% acrylic elastomeric polymers. Contains 30% Volume solid, tensile strength 8 kg/cm², crack bridging, VOC 30 ± 5 gm/ltr upto 2 mm. then applying two coats with forced *-coverage of 20 sqft/ltr/two coats. The operation shall be carried out after scrapping & propely cleaning the surface to remove loose particles with wire brush/Jet washer. Apply 1 coat @1 ltr/10 sqm & 3 undiluted coats @ 8 ltr/10 sqm with 4 hrs interval of each coat. The work shall be carried out as recommended by the manufacturer’s specification & the direction of the Engineer in-Charge.

Wiring for circuit wiring with PVC insulated cable FRLS with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) of ISI marked suitable size etc. as required as per specification 2x2.5 Sq.mm.

Supply and fixing Led tube rod comprising of LED tube with nonintegral/integral driver, upto 6500K color temp having 40000 burning hrs life with minimum @ L 70, system lumen output should be minimum with system efficacy 100 lm/Watt. LED driver PF 0.95 & THD 20%. The colour rendering index of LED light should be more than 70. Submission LM 79-08/IS16106 (2012), IEC60598, IEC61347i/c connection wire, testing etc. to complete the job. Tube light LED 1 X 20/22Watt, Integral i/c batten aluminium body, PC diffuser.

Supplying, erecting and testing of approved make exhaust fan heavy duty with mounting frame, blades AC 230-250 complete connection and including, frame bolt/anchor hole fasteners etc. complete finished and as required. 300mm sweep RPM 900 / 1400

Supply and fixing as per specification Switch of approved make ISI marked with necessary material complete. 6/10/16 Amp SP 250 Volt modular switch.

Supply and laying, testing & commissioning of following sizes of copper conductor control cables on existing tray including fixing clamps & proper connections to equipment etc. complete as required 4Cx 10 sq.mm