MP Power Transmission Company Limited Tender

(MPPWD SOR No.21.2.2)Providing and fixing 12mm thick Pre-laminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides.

(MPPWD SOR No.9.84)Providing and fixing bright finished brass 100 mm mortice latch and lock ISI marked with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles with necessary screws etc. complete (Best make of approved quality).

(MPPWD SOR No.10.27.2)Providing and fixing glass panes/ steel sheet/ fibre sheet with putty and glazing clips in steel doors, windows, clerestory windows all complete. With 5.50 mm thick glass panes

(MPPWD SOR No.21.5.2)"Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body /plate with double spring mechanism and door weight upto 125 kg., for doors, including cost of cutting floors , embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge : With brass cover plate - minimum 1.25 mm thickness."

(MPPWD SOR No.9.109.1)Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete: 300x16 mm

(MPPWD SOR No.9.109.2)Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete: 250x16 mm

(MPPWD SOR No.9.110.3)Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete: 250x10 mm

(MPPWD SOR No.9.113.1)Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete: 125 mm

(MPPWD SOR No.9.48)"Providing 40x5 mm flat (iron hold fast 40 cm long) (0.628 kg) including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 sand : 6 graded stone aggregate 20mm nominal size)"

1000557, NOSR Payment of fixed additional charges for Mobilization of men, materials, T&P etc. due to change in location of work from one substation/premises to another substation/premises after 1st sub order for each separate sub-order (s) under the scope of same contract of civil works shall be payable as per following conditions: -(i) Applicable only after 1st sub work order and only on change in work location from one substation/premises to another substation or any other MPPTCL’s premises situated at a distance of more than 3.00 Kms. for execution of work under the same main contract. (Nearest motorable road distance shall be considered for this purpose) (ii) The distance as mentioned in point no. – (i) shall be considered from the nearest current location of ongoing work (where the work shall be in progress by the contractor at the time of placing new sub-order irrespective of scheduled completion period given for that work) under the scope of same contract. (iii) Not applicable for the balance work (when the sub order of any civil work is placed in two or more parts) of dusting, metaling etc. on the same feeder bay work for which the work of foundation etc. has been executed previously under the scope of same contract.(iv) The rates are inclusive of cost of transportation of labour, material, T&P etc. and cost of all respective works in all respect up to any distance in the area of jurisdiction of main work order for the contract and also in nearby areas as per necessity i/c all applicable taxes (except GST) etc. all complete, as per terms and conditions of order and as per direction of Engineer – In – Charge.(Base Rate: - Rs. 10,000/- per shifting) Note:- This payment of fixed additional charges for changing of work location shall be payable only when work will be executed in accordance with location wise priority fixed by the Engineer-In-Charge (if any) and only on successful completion of work in all respect as per scope of work in the sub-order for which said additional charges are to be payable.