MP Power Transmission Company Limited Tender

3004746,2.6(SOR w.e.f 01.12.2020),Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5m in width as well as 10 sqm on plan) including dressing of sides and ramming of bottom disposal of excavated earth, lead up to 50m and lift up to 1.5m, disposed earth to be levelled and neatly dressed. (No extra lift is payable if work is done by mechanical means) All kinds of soil

3004838,4.1.2.3(SOR w.e.f 01.12.2020),Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level : With 40mm nominal size graded stone aggregate. M-7.5 Nominal Mix -1 Cement : 4 sand : 8 graded stone aggregate

3004834,4.1.1.3(SOR w.e.f 01.12.2020),Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level : With 20mm nominal size graded stone aggregate. M-15 – Grade concrete

3004994,6.5.2(SOR w.e.f 01.12.2020),Brick work with well brunt open bhatta, bricks, crushing strength not less than 25kg /cm2 and water absorption not more than 20% in foundation and plinth i/c curing etc complete. Cement Mortar 1:6 (1 cement: 6 sand).

3005976,12.1.3(SOR w.e.f 01.12.2020),"Providing corrugated G.S. sheet roofing including vertical/ curved" surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete upto any pitch in horizontal/ vertical or curved surfaces) excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.63 mm thick with zinc coating not less than 275gm/m²

3005980,12.4.2(SOR w.e.f 01.12.2020),Providing ridges or hips of width 60 cm over all width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia. G.I. limpet and bitumen washers complete. 0.63mm thick with zinc coating not less than 275gm/m²

3005988,12.11(SOR w.e.f 01.12.2020),Extra for providing and fixing wind ties of 40x 6 mm flat iron section.

3005000,6.7.2.2(SOR w.e.f 01.12.2020),Brick work with fly ash lime bricks (FALG Bricks) conforming to IS:12894-2002, in super structure above plinth level up to floor two level in : Having 75 kg / cm2 average compressive strength. Cement mortar 1:6 (1 cement : 6 sand)

3005875,11.49 (SOR w.e.f 01.12.2020),Providing and fixing Ceramic glazed wall tiles 300x450 mm or more (having thickness 6 to 7 mm) of 1st quality conforming to IS: 15622 of approved make in all Colours& shades, except burgundy, bottle green, black laid on 12mm thick bed of Cement Mortar 1:3 (1 Cement: 3 sand)preprad same day when mortar is still green jointed with grey cement slurry @3.3 kg per sqmincluding pointing the joints with white cement and matching pigments etc., complete.

3005874,11.48 (SOR w.e.f 01.12.2020),Providing and laying Ceramic glazed floor tiles 300x300 mm or more (having thickness 6 to 7mm) of 1st quality conforming to IS : 15622 of approved make in any colours and shade laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 sand) including pointing the joints with white cement and matching pigment etc., complete.

3006598,17.2.1(SOR w.e.f 01.12.2020),Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required :..W.C. pan with ISI marked white solid plastic seat and lid

3006596,17.1.1(SOR w.e.f 01.12.2020),Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100mm sand cast Iron P or S trap, UPVC P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required :..White Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type foot rests.

3006605,17.6.1(SOR w.e.f 01.12.2020),"Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :..One urinal basin with 5 litre white P.V.C. automatic flushing cistern."

3006620,17.11.2(SOR w.e.f 01.12.2020),"Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require :..White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap."

3007319,19.9.1.1(SOR w.e.f 01.12.2020),"Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 sand ) R.C.C. top slab with Cement Concrete 1:2:4 mix (1 cement : 2 sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:2:4 mix (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :..With well burnt bricks"

3007291,19.4.1(SOR w.e.f 01.12.2020),Providing and laying below ground unplasticised PVC pipe to with stand working pressure of 4 kg/cm2 soild waste pipes confirming to IS:13592 and IS:4985 including jointing with seal ring confirming to IS :5282 leaving 10mm gap for thermal expansion all necessary fittings etc. complete. Excavation to be paid seperataly...110 mm diameter OD (min. wall thickness 3.2mm)

3007292,19.4.2(SOR w.e.f 01.12.2020),Providing and laying below ground unplasticised PVC pipe to with stand working pressure of 4 kg/cm2 soild waste pipes confirming to IS:13592 and IS:4985 including jointing with seal ring confirming to IS :5282 leaving 10mm gap for thermal expansion all necessary fittings etc. complete. Excavation to be paid seperataly...160 mm diameter OD (min. wall thickness 4.0mm)

3007269,18.61(SOR w.e.f 01.12.2020),Providing and fixing CP jet assembly to including connection etc complete.

3006924,18.6.2.2(SOR w.e.f 01.12.2020),Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittingsi/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge...Concealed work including cutting chases and making good the walls etc...20 mm nominal outer dia .Pipes.

3006925,18.6.2.3(SOR w.e.f 01.12.2020),Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittingsi/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge...Concealed work including cutting chases and making good the walls etc.25 mm nominal outer dia .Pipes.

3007215,18.31(SOR w.e.f 01.12.2020),Providing and fixing C.P. brass bib cock of approved quality conforming to IS: 8931, 15 mm nominal bore.

3006839,17.78.1(SOR w.e.f 01.12.2020),Providing and fixing C.P. Brass grating of approved quality and make conforming to IS: specification...100 mm dia.

3006832,17.72(SOR w.e.f 01.12.2020),Providing and fixing CP brass bottle trap of approved quality and make for sink and wash basin.

3005920,11. 78.1.1 (SOR w.e.f 01.12.2020),Providing and laying vitrified floor tiles Multi/Double charged (Minimum top layer thickness 2.0mm) Neno Polished self design, in different size with water absorption less than 0.05% and conforming to IS:15622 of approved make in all colours& shades, quality/ premium quality in flooring laid on 12mm thick cement mortar 1:4(1cement :4sand) including grouting the joints with white cement and matching pigments etc. complete In light shade glossy/ rustic /stain finished Size 600X600 mm thickness 9-10 mm

3006834,17.73.2(SOR w.e.f 01.12.2020),Providing and fixing CP brass towel rail of approved quality and make..450x20mm

3006835,17.74(SOR w.e.f 01.12.2020),Providing and fixing CP brass towel ring of approved quality and make 200mm dia ring

3006836,17.75(SOR w.e.f 01.12.2020),Providing and fixing CP brass soap dish of approved quality and make

3006837,17.76(SOR w.e.f 01.12.2020),Providing and fixing CP brass Urinal spreader of approved quality and make

3006838,17.77(SOR w.e.f 01.12.2020),Providing and fixing C.P. brass soap container 109 mm wide, 125 high and 112 mm distance from wall of standard shape with bracket of the same material with all fittings etc. of approved quality and conforming to IS: specification.

3007474,21.1.2.2(SOR w.e.f 01.12.2020),Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows and ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately). Powder coated aluminium (minimum thickness of powder coating 50 micron)

3005751,21.1.1.2(SOR w.e.f 01.12.2020),Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion. Powder coated aluminium (minimum thickness of powder coating 50 micron)

3007478,21.2.2(SOR w.e.f 01.12.2020),Providing and fixing 12mm thick Pre-laminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides.

3007480,21.3.2(SOR w.e.f 01.12.2020),Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item) : With float glass panes of 5.0 mm thickness (weight not less than 12.50 kg/sqm )

3006147,13.2.2(SOR w.e.f 01.12.2020),15 mm cement plaster on the rough side of single or half brick wall of mix 1:6 (1 cement : 6 sand)

3006211,13.46(SOR w.e.f 01.12.2020),Wall painting by any mechanical or manual means with plastic emulsion paint of approved brand and manufacture to give an even shade: Two or more coats on new work

3000163,56a NSOR,Wiring for the following light points with 1.5 Sq. mm PVC insulated copper conductor ( Finolex, Havells, Anchor or equivalent) 650 Volts grade standard wire in concealed 25 mm dia 2 mm thick rigid PVC pipe of approved make i/c switches, lamp holder, Ceiling rose (Anchor, Havells or equivalent make) , GI Box/ wooden box and all other required fittings & fixtures of approved make including providing 5 Amp grid plate (Anchor, Havells or equivalent ) complete. The work include cost of all material, T&P, labour, making grooves and after the work done, to make the wall & other structural components good to the desired finish complete as per direction of Engineer in charge. short point upto 3 m

3000164,56b NSOR,Wiring for the following light points with 1.5 Sq. mm PVC insulated copper conductor ( Finolex, Havells, Anchor or equivalent) 650 Volts grade standard wire in concealed 25 mm dia 2 mm thick rigid PVC pipe of approved make i/c switches, lamp holder, Ceiling rose (Anchor, Havells or equivalent make) , GI Box/ wooden box and all other required fittings & fixtures of approved make including providing 5 Amp grid plate (Anchor, Havells or equivalent ) complete. The work include cost of all material, T&P, labour, making grooves and after the work done, to make the wall & other structural components good to the desired finish complete as per direction of Engineer in charge. Medium point 3 to 6 metres

3000167,58a NSOR,Wiring for the fan/ exhaust fan / call bell points with 1.5 Sq. mm PVC insulated copper conductor ( Finolex, Havells, Anchor or equivalent) 650 Volts grade standard wire in concealed 25 mm dia, 2 mm thick rigid PVC pipe of approved make i/c switches, , Ceiling rose (Anchor, Havells or equivalent make) , GI / wooden box and all other required fittings & fixtures of approved make including providing 5 Amp grid plate (Anchor, Havells or equivalent ) complete. The work include cost of all material, T&P, tax, transportation etc., labour, making grooves and after the work done, to make the wall & other structural components good to the desired finish complete as per direction of Engineer in charge. short point upto 3 m

3000168,58b NSOR,Wiring for the fan/ exhaust fan / call bell points with 1.5 Sq. mm PVC insulated copper conductor ( Finolex, Havells, Anchor or equivalent) 650 Volts grade standard wire in concealed 25 mm dia, 2 mm thick rigid PVC pipe of approved make i/c switches, , Ceiling rose (Anchor, Havells or equivalent make) , GI / wooden box and all other required fittings & fixtures of approved make including providing 5 Amp grid plate (Anchor, Havells or equivalent ) complete. The work include cost of all material, T&P, tax, transportation etc., labour, making grooves and after the work done, to make the wall & other structural components good to the desired finish complete as per direction of Engineer in charge. Medium point 3 to 6 metres

3000171,59a NSOR,"Point wiring for 3 pin, 15 Amp Socket outlet point with 15 Amp Switch on separte board with 4 Sq. mm PVC insullated copper conductor of Havells, Anchor or equivelant make and all other required fittings and fixtures of Anchor, Havells or equivelant make in 25 mm dia rigid PVC conduit 2 mm thick of approved make including 2 mm bare copper earth continuity conductor with all cost of material , tax, transportation etc., T&P, labour and making grooves & making the same good in smooth finish as directed by Engineer in charge. Short Point (upto 3 m )"

3000172,59b NSOR,"Point wiring for 3 pin, 15 Amp Socket outlet point with 15 Amp Switch on separte board with 4 Sq. mm PVC insullated copper conductor of Havells, Anchor or equivelant make and all other required fittings and fixtures of Anchor, Havells or equivelant make in 25 mm dia rigid PVC conduit 2 mm thick of approved make including 2 mm bare copper earth continuity conductor with all cost of material , tax, transportation etc., T&P, labour and making grooves & making the same good in smooth finish as directed by Engineer in charge. Medium Point (3 m to 6m )"

3000175,60 NSOR,Point wiring for 3 pin, 5 Amp Socket outlet point with 5 Amp Switch on same board with 1.5 Sq. mm PVC insullated copper conductor of Havells, Anchor or equivelant make and all other required fittings and fixtures of Anchor, Havells or equivelant make with suitable size rigid PVC conduit 2 mm thick of approved make including bare copper earth continuity conductor of suitable size with cost of all materials, transportation etc., T&P, labour and making grooves & making the same good in smooth finish as directed by Engineer in charge.

3000176,61 NSOR,Point wiring for 3 pin, 5 Amp Socket outlet point with 5 Amp Switch on seperate board with 1.5 Sq. mm PVC insullated copper conductor of Havells, Anchor or equivelant make and all other required fittings and fixtures of Anchor, Havells or equivelant make with suitable size rigid PVC conduit 2 mm thick of approved make including bare copper earth continuity conductor of suitable size with cost of all materials, transportation etc., T&P, labour and making grooves & making the same good in smooth finish as directed by Engineer in charge.

3000177,62a NSOR,"Wiring for circuit wiring with PVC insulated copper conductor of Finolex, Havells, Anchor or equivelant make in rigid PVC Conduit 25 mm dia 2 mm thick of approved make with bare copper earth conductor of suitable size and all other required fittings of approved make including cost of all material, T&P, taxes, transportation etc., labour and making good the surfaces to the smooth finish after completion of the work as per direction of Engineer in charge. 2x1.5 Sqmm"

3000178,62b NSOR,"Wiring for circuit wiring with PVC insulated copper conductor of Finolex, Havells, Anchor or equivelant make in rigid PVC Conduit 25 mm dia 2 mm thick of approved make with bare copper earth conductor of suitable size and all other required fittings of approved make including cost of all material, T&P, taxes, transportation etc., labour and making good the surfaces to the smooth finish after completion of the work as per direction of Engineer in charge.2x 2.5 Sqmm"

3005482,9.134.1 (SOR w.e.f 01.12.2020),Providing and Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S including cost of adhesive of approved quality. 1.5 mm thick.

3006112,12.62.5(SOR w.e.f 01.12.2020),Providing and fixing board ceiling of approved quality with necessary nails etc. complete (frame work to be paid separately): 4 mm thick High Pressure Steam Cured non asbestos, pre-painted, self embossed, designer cement boardType B, Category 3 conforming to IS 14862:2000 . of approved texture,design patterns

3005007,6.11(SOR w.e.f 01.12.2020),Extra for brick work in superstructure above floor two levelsfor each additional floor or part thereof respective item. (Rate - 2 % of respective item)

3005717,10.26.2 (SOR w.e.f 01.12.2020),Providing and fixing fly proof wire gauze to windows, clerestory windows and doors with M.S. Flat 15x3mm and nuts and bolts complete. Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides.

3005947,11. 82.3 (SOR w.e.f 01.12.2020),Providing and laying digital print random design(PGVT)/(GVT) vitrified tiles in different sizes with water absorption less than 0.05% and conforming to IS:15622 of approved make in all colours& shades, 1st quality/ premium quality including grouting the joints with white cement and matching pigments etc. complete . For wall polished / Glossy finished laid on 12mm thick cement mortar 1:3 (1 cement:3sand) prepared same day when mortar is still green i.e. within 6 hours, Size 300X600 mm thickness 9-10 mm

3006220,13.53(SOR w.e.f 01.12.2020),Finishing walls by any mechanical or manual means with Premium Acrylic Smooth exterior paint (Premium exterior) of required shade including all scaffolding. New work (Two or more coat applied @1.67ltr/10sqm over and including one coat undiluted exterior waterproofing coating @ 2.39 litre/10 sqm with crack bridging ability of upto 0.5mm on horizontal surfaces with an elongation of 150% and water proofing of upto 3 bars on vertical surface)

3006242,13.66.1(SOR w.e.f 01.12.2020),Painting with synthetic enamel paint, having VOC (Volatile Organic Compound) content less than 150 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. One coat.

3006087,12.58.1.1(SOR w.e.f 01.12.2020),Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 10mm thick plaster of Paris (gypsum anhydrous) sheet 10mm thick pop board Flat surfaces

3000216,88 NSOR,Providing & fixing 35 to 40 mm thick Polished Cuddappa stone slab for tiers of cup board, ward robe and shelf below kitchen platform fixed with 12 mm thick cement mortar 1:3 (1 cement :3 sand) and jointing with cement slurry mixed with suitable plgment to match the approved shade of stone complete including cutting, rubbing, polishing, T&P, taxes, labour, transportation etc, complete as per direction of engineer -in-charge.

3005119,7.35.3(SOR w.e.f 01.12.2020),Stone work ( machine cut edges) for wall lining upto 10 m height etc. (Veneer work) backing filled with a grout of 12mm thick cement mortar 1:3 (1 Cement : 3 sand) and jointed with Cement mortar 1:2 (1 cement : 2 marble dust) including rubbing and polishing complete. (To be secured to the backing by means of cramps which shall be paid for separately) 20 to 25mm thick kota stone slabs exposed slab not dressed and rubbed.

3005828,11.22.5 (SOR w.e.f 01.12.2020),Providing and fixing 18mm thick gang saw cut mirror polished (premoulded and prepolished) machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing moulding and polishing to edge to give high gloss finish wherever required etc. complete at all levels. Samples approved by Engineer-in- Charge. Cuddpah stone

3005827,11.22.4 (SOR w.e.f 01.12.2020),Providing and fixing 18mm thick gang saw cut mirror polished (premoulded and prepolished) machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing moulding and polishing to edge to give high gloss finish wherever required etc. complete at all levels. Samples approved by Engineer-in- Charge. Granite grey/pink/brown with various patterns

3005860,11.39.2 (SOR w.e.f 01.12.2020),Providing edge moulding to 18mm thick marble stone counters, Vanities, window sills etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work.

EHT-Main. Dn. Satna 3006475,15.27.2(SOR w.e.f 01.12.2020), "Dismantling roofing including ridges, hips valleys and gutters etc., and stacking the material within 50 metres lead of:..Asbestos/ Non asbestors sheet"

3006442,15.6.3(SOR w.e.f 01.12.2020),Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in- Charge...In cement mortar.

3005976,12.1.3(SOR w.e.f 01.12.2020),"Providing corrugated G.S. sheet roofing including vertical/ curved" surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete upto any pitch in horizontal/ vertical or curved surfaces) excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.63 mm thick with zinc coating not less than 275gm/m²

3005980,12.4.2(SOR w.e.f 01.12.2020),Providing ridges or hips of width 60 cm over all width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia. G.I. limpet and bitumen washers complete. 0.63mm thick with zinc coating not less than 275gm/m²

3005988,12.11(SOR w.e.f 01.12.2020),Extra for providing and fixing wind ties of 40x 6 mm flat iron section.

3005000,6.7.2.2(SOR w.e.f 01.12.2020),Brick work with fly ash lime bricks (FALG Bricks) conforming to IS:12894-2002, in super structure above plinth level up to floor two level in : Having 75 kg / cm2 average compressive strength. Cement mortar 1:6 (1 cement : 6 sand)

3006147,13.2.2(SOR w.e.f 01.12.2020),15 mm cement plaster on the rough side of single or half brick wall of mix 1:6 (1 cement : 6 sand)

3006211,13.46(SOR w.e.f 01.12.2020),Wall painting by any mechanical or manual means with plastic emulsion paint of approved brand and manufacture to give an even shade: Two or more coats on new work

3005007,6.11(SOR w.e.f 01.12.2020),Extra for brick work in superstructure above floor two levelsfor each additional floor or part thereof respective item. (Rate - 2 % of respective item)

3005717,10.26.2 (SOR w.e.f 01.12.2020),Providing and fixing fly proof wire gauze to windows, clerestory windows and doors with M.S. Flat 15x3mm and nuts and bolts complete. Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides.

3006220,13.53(SOR w.e.f 01.12.2020),Finishing walls by any mechanical or manual means with Premium Acrylic Smooth exterior paint (Premium exterior) of required shade including all scaffolding. New work (Two or more coat applied @1.67ltr/10sqm over and including one coat undiluted exterior waterproofing coating @ 2.39 litre/10 sqm with crack bridging ability of upto 0.5mm on horizontal surfaces with an elongation of 150% and water proofing of upto 3 bars on vertical surface)

3006242,13.66.1(SOR w.e.f 01.12.2020),Painting with synthetic enamel paint, having VOC (Volatile Organic Compound) content less than 150 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. One coat.

3006087,12.58.1.1(SOR w.e.f 01.12.2020),Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 10mm thick plaster of Paris (gypsum anhydrous) sheet 10mm thick pop board Flat surfaces