MP Power Transmission Company Limited Tender

(NSOR)Providing & fixing in position LDPE film of 150 micron (0.15 mm) ISI mark 2508 (Grade 231) i/c heat sealed joints at ends as per IS 9698 i/c cost of material labour, T&P, Taxes, transportation etc. compete as per directions of Engineer - in-charage (Base Rate - Rs. 25/- per Sqm)

(SOR-4.1.1.4) Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: Nominal Mix -1 Cement : 3 sand : 6 graded stone aggregate (M 10)

(NSOR) Supply stacking and spreading of 40mm crusher broken metal black trap basalt or granite uniformly in substation yard in desired thickness, free from dust and foreign matter, including transportation up to site lead and lift, T&P, labour, royalty and taxes etc. complete as directed by Engineer-in-charge (Base rate 1003/M3)

(SOR-11.83) Providing and aying factory made coloured chamfered edge Cement Concrete paver blocks of required strength, thickness and size/shape. made by table vibratory method using PU mould, laid in required colour and pattern over 50mm thick compacted bed of stone dust, compacting and proper embedding/laying of inter locking paver blocks into the bedding layer through vibratory compaction by using plate vibrator, filling the joints w ith sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand including locking edges with M 15 cement concrete in footpath, parks, lawns, drive ways or light traffic parking etc. complete as per manufacturer’s specifications and direction of Engineerin' Charge. 80mm thick C.C. paver block of M-35 grade with approv ed colour, design and pattern.

(SOR-4.1.2.3) P/L in position cement concrete of specified grade M-7.5 with 40mm metal, 1:4:8

(SOR-5.16.3) Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding including cost of binding wire up to floor two level including all wastage etc. complete. Cold twisted bars (CTD)

(SOR-5.1.1) Providing and laying in position specified grade of reinforced cement concrete (with 20mm nominal size graded stone aggregate) excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :

(SOR-5.9.1) Centering and shuttering including strutting, propping etc. and removal of form for : Foundation, footings, basees of columns etc. for concrete up to plinth level

(SOR-5.9.2) Centering and shuttering including strutting, propping etc. and removal of form for : Foundation, Walls (any thickness) including attached pilasters butteresses, plinth beams and string courses etc.up to plinth level.

(SOR-4.1.1.3) Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: M 15 Grade concrete

(SOR-10.22.1) Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In stringers

(SOR-15.6.3)Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in -charge.In cement mortar.

(SOR-6.6.2) Brick work with well brunt open bhatta. bricks, crushing strength not less than 25kg / cm2 and water absorpt ion not more than 20% in superstructure above plinth level and up to floor level i/c curing etc complete. Cement Mortar 1:6 (1 cement: 6 sand)

(SOR-13.2.2) 15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6(1 cement: 6 sand)

(SOR-11.45)Providing and laying Ceramic glazed floor tiles 300x300 mm or more (having thickness 6 to 7mm) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory , Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4(1 Cement : 4 sand) including pointing the joints with white cement and matching pigment etc . complete.

(SOR-11.46) Providing and fixing Ceramic glazed wall tiles 300x450 mm or more (having thickness 6 to 7 mm) of 1st quality conforming to IS 15622 of approved make in all Colours shades. Except burgundy. Bottle green. Black, laid on 12mm thick bed of Cement Mortar 1:3 (1 Cement : 3 sand) jointed with grey cement slurry @3.3 kg per sqm including pointing the joints with white cement and matching pigments etc., complete.

(SOR-17.3.1) Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern and C.P flush bend with fittings and C.l brackets. 40mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete including painting of fittings and brackets, cutting and making good the walls and floors wherever required: W.C. pan with ISI marked white solid plastic seat and lid

(SOR-17.6.1)Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x265mm sizes respectively with automatic flushing cistern with standard flush pipe and C P brass spreaders with brass unions and G.l clamps complete, including pamting of fittings and brackets, cutting and making good the walls and floors wherever required : One urinal basin with 5 litre white P.V.C. automatic flushing cistern.

(SOR-17.11.1) Providing and fixing wash basin with C.I. brackets, 15 mm C.P brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P brass pillar taps

(SOR-17.12) Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

(SOR-17.67) Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C P, brass screws and washers complete.

(SOR-18.52.1)Providing and fixing C.P brass bib cock of approved quality conforming to IS:8931 15 mm nominal bore.

(SOR-12.32.2) Providing and fixing wash basin with C.I. brackets, 15 mm C.P brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P brass pillar taps

(NSOR) Providing & Fixing 380 mm 900 rpm wall mounting heavy duty exhaust fan of approved make (Crompton/ Havells/Bajaj or equivalent make) with motor mounting frame blades i/c fitting and making all required connections to the circuit & complete as per direction of Engineer incharge (Base Rate Rs. 3150/each)

(SOR-9.163.1)Providing and fixing to existing door frames 24 mm thick factory made PVC door shutters ...... size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. ..... M S galvanised/plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M S 'U' cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M S rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge. (For W.C and bathroom door shutter).

(SOR-10.22.2) Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works,

(SOR- 18.10.1) Providing and fixing G.l. pipes complete with G.l fittings and clamps, including cutting and making good the walls etc.Internal work - Exposed on wall 15 mm dia. nominal bore