MP Police Housing And Infrastructure Development Corporation Limited Tender

Steel tubular pole Supply of steel tubular pole swaged type as per IS:2713-1980 complete with base plate and top Canopy 410 SP-29 - 9.00 metre

Erection of poles, Erection of RS Joist pole/'H' beam/steel tubular/steel rail pole of length 7 metres but not exceeding 10 metres in cement concrete 1:3:6 (1 cement : 3 core sand: 6graded stone aggregate 40mm nominal size) base, foundation, muffing including excavation and back refilling etc. as required.

Water tight terminal box Supplying and erection of water tight terminal box made of PC-GFS (polycarbonate),IP 66 /IP 67 (cable entry systems LES) in accordance with IEC 60670-22, resistant to weather influences (UV due to solar radiation, protected against rainwater, temperature resistant, impact resistant, etc. insulation voltage 1000 V a.c./d.c., wall thickness of the bottom part 2 / 2.7 mm of required size suitable for kit kat/MCB/switch including 2nos. pole clamp of M.S. flat iron size 32x3mm, nut and bolts, excluding the cost of the kit kat/MCB/Switch, 4 Pole epoxy connector nut & bolt type, 30Amp, 500Volt complete as per specification as mentioned below.155 x 210 x 92 mm

Stay set Supplying and erection of stay set complete with 19/20mm.dia 1.8 metre long stay rod, turn buckle, anchor plate of size 300mm x 300mm x 7.5mm thimble stay clamp, bow tightener, 7/4.00 dia G.I. stay wire etc. in cement concrete M-10 (1 cement: 3 coarse and: 6 granded stone aggregate 40mm nominal size) foundation including excavation and back refilling etc. as required.

Angle/channel/flat iron fitting Supply, fabrication and erection of angle/channel/flat iron fitting for overhead line & sub-station etc such as 'D' bracket, cross arms, top clamp, 'V' cross arms, back/support clamp or other similar work etc. including nut bolts of required size, making holes, fabrication, welding, cutting, etc. and painting with one coat of red oxide paint & two coat of aluminium paint asrequired as per specification.

Polymer pin insulator Supplying and erection of 33KV (10 KN) polymer pin insulator complete with long steel head G.I. pin, nut, washer etc. as required.

Polymer disc insulators Supplying and erection of 33KV (45 KN) polymer disc insulators for 33KV overhead lines with galvanized insulator fittings, ball and socket type, and complete with galvanized strain clamp, bolts, nuts,washers etc. as required.

Porcelain pin insulator Supplying and erection of 33KV porcelain pin insulator complete with long steel head G.I. pin, nut, washer etc. as required.

Porcelain disc insulators Supplying and erection Set of Three 11 KV Porcelain disc insulators for 33KV overhead lines with galvanized insulator fittings, ball and socket type, and complete with galvanized strain clamp, bolts, nuts,washers etc. as required.

AB switch Supplying installing, testing & commissioning of outdoor H.T., AB switch assembly set gang operated with brass contact parts, including required GI pipe operating rod, handle & locking arrangement on On-Off position conforming to IS complete with required material and installing on existing DP structure to complete the job as required as per specification.(Set of 3 nos.) 33KV, 600Amp

AB switch Supplying installing, testing & commissioning of outdoor H.T., AB switch assembly set gang operated with brass contact parts, including required GI pipe operating rod, handle & locking arrangement on On-Off position conforming to IS complete with required material and installing on existing DP structure to complete the job as required as per specification.(Set of 3 nos.) 11KV, 600Amp

D.O. fuse Supplying installing, testing & commissioning D.O. fuse assembly with brass part contact for 33 or 11/0.4 KV DP Structure set of 3 Nos. with fuse barrel i/c required fuse element & other materials as per specification on existing D.P. structure as required.33KV

lightning arrestor Supplying and erection of single piece nonlinear resistor polymer type lightning arrestor (set of 3 nos) for 3 wire, 33KV overhead lines/ sub-station with rated voltage of 27KV (rms) with a nominal discharge current rating of 10 KA and complete with galvanized clamping arrangement, G.I. bolts, nuts, washer etc. as required.

Anti-climbing Supply & fixing anti climbing device with 2 ply G.I. barbed wire 1 Kg. per pole complete as per MPMKVVCO. Specification.

G.I. earth coil Supply, laying and fixing of G.I. earth coil of 4mm dia G.I. wire having 120 turns of nearly 50mm dia. and 3 mt. long tail in existing pit duly earthed with pole etc complete as required as per specification.

Danger Board Supplying and fixing 33/11/0.4 KV enamel coated danger board size 200x250mm with clamp on existing HT/LT structure/poles.

AAAC(Dog) conductors Supplying and drawing all aluminium alloy conductor (AAAC) of approved make conforming to IS 398-1979 Pt. IV, including binding at existing insulator,jointing, jumpering, tearing off, connecting etc. as required including clearing of obstacles (if any)AAAC 0.1 sq inch (100 sq.mm Al. EQ.)- (Dog)

Guard wire/earth wire/bearer wire Supplying and drawing guard wire/earth wire/bearer wire 13 sq mm (4mm. dia) G.I. including stringing, binding at existing insulators or brackets, jointing, jumpering, connecting & cradle etc. as required and clearing of obstacles (if any)

Coverd Conductor Supplying and drawing off coverd Conductor XLPE Insulation at the MPEB Normas and specification Complete 99 Squre mm/

Guards for existing overhead lines Supplying and erection of guards for existing overhead lines as required including split insulator required as per specification:Cradle type

Transformer, 33/0.4 KV 3 phase Supplying, installing, testing and commissioning of 33/0.4 KV 3 Phase 50 cycle oil immersed, naturally cooled, outdoor type transformer connected deltaon H.T. side and star on L.T. side, hand operated off load Tap changer switch, rating and diagram plate, two earthing terminal, lifting lugs, oil level gauge, drain valve with plug, temperature not exceeding 50ºC on load, temperature dial gauge, Bucholz relay, oil conservator with drain plug, oil filling hole with plug, dehydrating silica gel breather on eye level, four unidirectional roller, arcing horns, explosion vent, terminal arrangement bushing on H.V. side and cable box on LV side, first filling of oil upto desired level and transformer installing on existing structure with all required materialsarrangement as required ISI marked & asper IS specification.Energy efficiency level -2 Copper wound 750 KVA 33/0.433Kv (Copper Wound with tape Changing Arrangement)NLL 2.2KW and FLL 17.0 KW,

MAIN L.T.PANEL :Supplying, fixing, testing and commissioning of wall/floor mounted LT metering and distribution cubical panel,weather, dust and vermin proof, seven tank treatment process, 100 micron powder coating, suitable for 415 volt 3 phase 4 wire 50 Hz. system, fabricated out of CRCA 1.6mm thick sheet (1.2mm for doors and partition) with base frame of angle /channel iron, necessary support of slot angle/plates/MS plates, conduits as required duly compartmentalized for incomer, bus section, outgoings,cable alleys, energy meter etc. suitable cutout for ammeter, voltmeter, selector switch, frequency meter,phase indicating lamp, energy meter, push button etc complete as required. The rate include for supply and.fixing DMC/SMC supports, earthing terminals, detachable gland plate with knock out, door knob /industrial door lock, internal control and power suitable wiring with required size of copper cable, lugs, complete with nut, bolt, washer, providing name plates of all chambers etc.as per approved design, pattern and specifications. (With switchgear, busbar, metering and protection accessories, relay, push button). & following desired equipments and Instruments as detailed below. 4P 1600/2000A EDO ACB WITH SR 18G REL 65 KA,-3 Nos., make L&T or equivalent SHUNT RELEASE TYPE 240 V AC (2) -2 Nos.make L&Tor equivalent LOCKABLE TRIP PUSH BUTTON TYPE A.B.C.D., -2 Nos.make L&Tor equivalent sp MCB, 4A, 10 kA,-12 nos ,make L&Tor equivalent LED INDICATOR DIA 22.5 mm RED ,-2 Nos.,make L&Tor equivalent LED INDICATOR DIA 22.5 mm YELLOW ,-2 Nos.,make L&Tor equivalent LED INDICATOR DIA 22.5mm BLUE ,-2 Nos.,make L&Tor equivalent LED INDICATOR DIA 22.5mm GREEN ,-2 Nos.,make L&Tor equivalent LED INDICATOR DIA 22.5mm AMBER ,-2 Nos.,make L&Tor equivalent TNC SELECTOR SWITCH,BARREL LOCK (CENTER KEY LOCK,INO+INC,25A ,-2nos,make SALZERor equivalent Metering CT 1200/5A,15VA/1.0, -6 nos,make AEor equivalent Metering CT 600/5A,15VA/1.0 ,-6nosmake AEor equivalent 3Ph,4W,MFM -LED,240V,AC ,CL1 ,-2nos,make L&Tor equivalent 3Ph,4W,KWH -LCD,240V,AC WITH RS 485, -2nos,make L&Tor equivalent U/V RELAY,20-110VAC/DC,-2 nos,make L&Tor equivalent O/V RELAY,20-110VAC/DC,-2nos,make L&Tor equivalent RESTRICTED EARTH FAULT RELAY,-2nos,make ALSTOMor equivalent PHASE FAILURE RELAY WITH O/V&U/V RELAY,-2nos,make MINILECor equivalent SURGE PROTECTOR 100 KA,4P,4MOD,TYPE-1,-2nos,make LEGRANDor equivalent 4P,1600/2000A,EDO ACB WITH SR18G REL,65 kA,-1nos,make L&Tor equivalent SHUNT RELEASE TYPE 240V AC (2),-1nos,make L&T or equivalent LOCKABLE TRIP PUSH BUTTON TYPE A,B,C,D,-1nos,make L&Tor equivalent LED INDICATOR DIA 22.5mm, BLUE,-1nos,make L&Tor equivalent LED INDICATOR DIA 22.5mm, GREEN,-1nos,make L&T or equivalent AUTO/MANUAL SELECTOR SWITCH, 2P, 3W WITHOUT OFF,-1nos,make SLAZER or equivalent 3P,MCCB,Thermal Mag Rel,Ith=320-400A,36kA,-10nos,make L&Tor equivalent EXTENDED ROTARY HANDLE FOR DN3,-10 nos,make L&Tor equivalent SPREADER LINKS (8),-10 nos,make L&T or equivalent NEUTRAL 400A,-10 nos,make PACor equivalent SP MCB, 6A, 10 kA,-24 nos,make L&Tor equivalent Metering CT 400/5A,15VA/1.0,-24 nos,make AEor equivalent LED INDICATOR DIA 22.5mm, RED,-8nos,make L&Tor equivalent LED INDICATOR DIA 22.5mm, YELLOW,-8nos,make L&Tor equivalent LED INDICATOR DIA 22.5mm, BLUE,,-8nos,make L&Tor equivalent 3Ph,4W,DUAL SOURCE ENERGY METER -LCD,CL1,-8 nos,make L&Tor equivalent 3P,MCCB,Thermal Mag Rel,Ith=80-100A,25 kA,-5 nos,make L&Tor equivalent EXTENDED ROTARY HANDLE FOR DN0,-5 nos,make L&Tor equivalent NEUTRAL 100A,-5 nos,make PACor equivalent MCB, 6A, 10 kA,-15 nos,make L&Tor equivalent Metering CT 100/5A,5VA/1.0,-15 nos,make AEor equivalent LED INDICATOR DIA 22.5mm, RED 1Nos,-5 nos,make L&Tor equivalent LED INDICATOR DIA 22.5mm YELLOW -5 Nos.,make L&Tor equivalent LED INDICATOR DIA 22.5mm BLUE- 5 Nos.,make L&Tor equivalent 3Ph,4W,DUAL SOURCE ENERGY METER -LCD,CL1,-5 nos,make L&Tor equivalent 3P,MCCB,Thermal Mag Rel,Ith=50-63A,25 kA,-1 nos,make L&Tor equivalent NEUTRAL 100A,-1 nos,make PACor equivalent SP MCB, 6A, 10 kA,-3 bos,make L&Tor equivalent Metering CT 60/5A,5VA/5.0,-3 nos,make AEor equivalent LED INDICATOR DIA 22.5mm, RED,-1 nos,make L&Tor equivalent LED INDICATOR DIA 22.5mm, YELLOW,-1 nos,make L&Tor equivalent LED INDICATOR DIA 22.5mm, BLUE,-1 nos,make L&Tor equivalent 3Ph,4W,DUAL SOURCE ENERGY METER -LCD,CL1,-1 nos,make L&Tor equivalent 2500 AMP AL BUSBAR TPN (current density 1.0 amp/per sq. mm) -4 nos Electronic Intelligent panel Meter 2 Nos Electro Magnetic 50 to 200% Setting Over Current and 20 2Nos 80% Setting Earth Fault (2 O/C+1E/F) Relay Metering CT Of Suitable Rating and Class 6Nos Earth Fault Relay and Over Current Relay as Per Required Rating 1 Set Protection CT Of Suitable Rating and 6 Nos Rate for above panel

CABLE TRENCHES :Preparation of permanent cable trench of required size including excavation in all type of soil/rock providing base concrete of 1:4:8 ratio of 20 cm thick size providing 50 mm dia PVC sleeve pipe in base concreting at 10 meter intervals intervals for clearing of water, 20 cm thick brick masonary wall on both side of trench of required height, plastering etc. complete with providing and fixing angle iron of 50x50x5mm size duly painted with two coats of red oxide, duly embedded in brick masonry at a distance of every 1 meter lengthwise in trench, above 20cm. from finished base of trench including providing and fixing of required size of flat clamps and removing of waste soil up to a lead of 50 meters. 300x400 mm (Clear Inside)

CABLE TRENCHES :Preparation of permanent cable trench of required size including excavation in all type of soil/rock providing base concrete of 1:4:8 ratio of 20 cm thick size providing 50 mm dia PVC sleeve pipe in base concreting at 10 meter intervals intervals for clearing of water, 20 cm thick brick masonary wall on both side of trench of required height, plastering etc. complete with providing and fixing angle iron of 50x50x5mm size duly painted with two coats of red oxide, duly embedded in brick masonry at a distance of every 1 meter lengthwise in trench, above 20cm. from finished base of trench including providing and fixing of required size of flat clamps and removing of waste soil up to a lead of 50 meters. 300x600 mm (Clear Inside)

CABLE TRENCHES :Preparation of permanent cable trench of required size including excavation in all type of soil/rock providing base concrete of 1:4:8 ratio of 20 cm thick size providing 50 mm dia PVC sleeve pipe in base concreting at 10 meter intervals intervals for clearing of water, 20 cm thick brick masonary wall on both side of trench of required height, plastering etc. complete with providing and fixing angle iron of 50x50x5mm size duly painted with two coats of red oxide, duly embedded in brick masonry at a distance of every 1 meter lengthwise in trench, above 20cm. from finished base of trench including providing and fixing of required size of flat clamps and removing of waste soil up to a lead of 50 meters. 450x750 mm (Clear Inside)

FLAG STONE :Supplying and fixing of flag stone of following size asrequired. 900x450x50 mm

FLAG STONE :Supplying and fixing of flag stone of following size asrequired. 900x600x50 mm

FLAG STONE :Supplying and fixing of flag stone of following size asrequired. 600x600x50 mm

Earthing with G.I.earth plate Earthing with G.I. earth plate 600mm X 600mm X 6mm thick including accessories and providing masonry encloser in cement mortar, cover plate having locking arrangement on the top and G.I. watering pipe 20mm dia 2.7 metre long etc. (but without charcoal or coke and salt) complete as required.

Earthing with copper earth plate Earthing with copper earth plate 600mmX 600mm X 3mm thick including accessories and providing masonry encloser in cement mortar, cover plate having locking arrangement on the topand G.I. watering pipe 20mm dia 2.7 metre long etc. (but without charcoal or coke and salt) complete as required

Add extra Add extra for using salt and charcoal/coke for G.I. plate or copper plate earth electrode as required including excavation and refilling the pit in all type of soil, murrum

G.I. strip Supply and laying 25mm X 5mm G.I. strip at 0.5 metre below ground level as strip earth electrode including jointing etc. as required.

G.I. strip Supply and laying 50mm X 6mm G.I. strip at 0.5 metre below ground level/surface as strip earth electrode including jointing etc. as required.

Copper strip Providing and fixing 25mm X 5mm copper strip in 40 mm dia G.I. Pipe from earth electrode as required

Chemical Bore Earthing Supply and erection of approved make safe earthing electrode consisting pipe-inpipe technology as per IS 3043-1987 made of corrosion free G.I. pipes with constant ohmic value surrounded by highly conductive compound with high charge dissipation suitable for effective and maintenance free earthing in earth pit of minimum bore dia. 150mm size, as mentioned below :With 3 metre G.I. pipes having outer pipe dia of 50mm having 80-200 micron galvanizing, Inner pipe dia. of 25mm having 200-250 Micron galvanizing, connection terminal dia. of 12mm in nominal soil with 50 kg (two bag) back filling bentonite compound UL listed and confirm to relevant International/Indian standards around electrode upto ground level.

Vacuum Circuit Breaker Supplying, installation, testing and commissioning of triple pole outdoor type 11KV/33KV vacuum circuit breaker with outdoor control & relay panel with numerical static relay for feeder protection (1F). The installation of VCB shall be carried out in accordance with IS: 3072. The VCB shall be mounted on suitable size duly painted MS channel/angle iron structure with nut bolts and washer. The structure shall be fixed on existing cement concrete foundation. The complete work should be done as per IS specification 33 KV, 1250A VCB

BATTERY AND BATTERY CHARGER :Supplying, installation, testing and commissioning of 100AH capacity 30 volt (15 No cells each of 2.0 Volt) NICAD battery bank and other necessary materials etc. complete as required.

BATTERY AND BATTERY CHARGER :Supplying, installation, testing and commissioning of 30 volt 20A battery charger suitable of above battery bank with initial charging capacity capability in a duly painted MS enclosure complete with provision for keeping the 30 volt battery in the same enclosure complete as required as per specifications.

PG CLAMPS :Supplying and fixing following accessories of approved make with all required materials and labour as required suitable upto Dog conductor PG clamp

Tee CLAMPS :Supplying and fixing following accessories of approved make with all required materials and labour as required suitable upto Dog conductor Tee clamp

Bimetallic CLAMPS :Supplying and fixing following accessories of approved make with all required materials and labour as required suitable upto Dog conductor Bimetallic clamp

CHEQURE PLATE :Supplying, fabricating and installation of 6 mm thick MS chequered plate of required size with hook and finishing the same as required.

Heat shrinkable jointing kit Providing &making cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for 33 KV/11 KV single core XLPE alum. conductor cable as required as per specification and as per accepted standard including connection testing complete.Heat shrinkable Jointing kit 33 KV XLPE cable O.D. termination 1 x 70-185 sq. mm.

Heat shrinkable jointing kit Providing &making cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for 33 KV/11 KV single core XLPE alum. conductor cable as required as per specification and as per accepted standard including connection testing complete.Heat shrinkable Jointing kit 33 KV XLPE cable O.D. termination 3x120-185 sqmm

First Aid Box Supply of first aid box complete with medicine & bandage as per specification.

Shock instruction chart Supply of shock instruction chart duly framed with glass, as reqd.

Fiber discharge rod Supply of fiber discharge rod I/C connection copper lead tested.

Fencing of chain link mesh Supply & fixing fencing of chain link mesh 100 x 100 mm, 12 SWG GI wire for electric sub-station switch yard including single post of angle iron size 50x50x5mm, 2.5 mt long should be provided upto 2.00 mt. apart or as required with angle iron/ flat iron members /cross members including mesh fix on frame and erected between the post. The angle iron post shall be erected in cement concrete M-15 (1:2:4) (20 mm graded metal) foundation, cement concrete, excavation of pit and refilling the same. The fencing shall be provided with one entrance gate including locking arrangement as required as per specification. The height of fencing shall be 2 mt. above ground level. Fencing shall be painted with required shade.

C.T./P.T Supplying, installation, testing and commissioning of single phase C.T./P.T. outdoor type 11KV/33KV with terminal box. The C.T./P.T. shall be mounted onexisting structure fabricated with suitable size MS channel/angle iron structure with nut bolts and washer duly painted. The structure shall be fixed on existing cement concrete foundation as per IS specificationas mentioned below.33 KV CT outdoor type 200-100/5 Amp.

C.T./P.T Supplying, installation, testing and commissioning of single phase C.T./P.T. outdoor type 11KV/33KV with terminal box. The C.T./P.T. shall be mounted on existing structure fabricated with suitablesize MS channel/angle iron structure with nut bolts and washer duly painted. The structure shall be fixed on existing cement concrete foundation as per IS specification as mentioned below.33 KV/110V single phase PTs oil immersed

DC PANEL :Supplying, installation, testing and commissioning of DC Panel of suitable size of 14 SWG CRCA sheet duly painted with two coats of red oxide and two coats of synthetic enamel paint consisting 1 no. DP MCB 32 amp. and 12 nos. SP MCB 10 amp. suitable for DC supply withneutral link as required as per specification.

AC PANEL :Supplying, installation, testing and commissioning of AC Panel of suitable size of 14 SWG CRCA sheet duly painted with two coats of red oxide and two coats of synthetic enamel paint consisting 1 no. SPN MCB 32 amp. and 12 nos. SP MCB 10 amp. suitable for AC supply with neutral link as required as per specification. sitc of il immersd 0.5 accuracy class 50 HZ CTPT combined unit complete with all necessary material as required including testing calibraty chages of electricity board as required.1. 33/110 volt, 3 phase four wire CTPT combined unit 400-200/5 amp or 300-150/5 amp or 200-100/5 amp CT rating

CAPACITOR PANEL Supplying, fixing testing and commissi oning of wall / floor mounted manual cum automatic power factor improvement capacitor panel, weather, dust and vermin proof, seven tank treatment process ,100 micron powder coating, suitable for 415 volt three phase 4 wire 50 hz system fabricated by 1.6mm thick CRCA sheet ( 1.2 mm for doors and partitions) with base frame of angle / chanel iron , necessary support of slot angle /plates/MS plates,conduits as required duly compartmentalized for incomer, bus section, outgoings, cable alleys, energy meter etc. suitable cutout for ammeter, voltmeter, selector switch, frequency meter, phase indicating lamp, energy meter, push button etc. complete as required . The rate include for supplying and fixing DMC/SMC supports, earthing terminals, detachable gland plates with knock out , door knob/ industrial door lock, internal control and power wiring with required size of copper cable, lugs, complete with nut bolts, washers, providing name plate of all chambers etc as per approved design, pattern and specifications complete with following items / materials. (Make : 1) MCCB-L&T/Schneider/Siemens/Legrand , 2) Disconnector switch fuse-L&T/ Schneider/Siemens, 3) Contactor-L&T/ Schneider/Siemens,4) Capacitor-Schneider/Meher, 5) PF Controller- L&T/ Schneider/Siemens) HEAVY DUTY CAPACITOR 12.5 KVAR, 440V,-2 NOS,MAKE L&T or equivalent HEAVY DUTY CAPACITOR 25 KVAR, 440V,-2 NOS,MAKE L&Tor equivalent HEAVY DUTY CAPACITOR 50(25x2) KVAR, 440V,-4 NOS,MAKE L&Tor equivalent APFC RELAY 12 STAGE,STATIC SWITCHING PFC,-1nos ,MAKE L&Tor equivalent 3P,MCCB,Thermal Mag Rel,Ith=500-630A,36kA,-1 NOS,MAKE L&Tor equivalent EXTENDED ROTARY HANDLE FOR DN3,-1 NOS,MAKE L&Tor equivalent SPREADER LINKS (6),-1 NOS ,MAKE L&Tor equivalent NEUTRAL 400A,-1 NOS,MAKE PACor equivalent 3P,MCCB,Thermal Mag Rel,Ith=25-32,25 Ka,-2 NOS,MAKE L&Tor equivalent 3P,MCCB,Thermal Mag Rel,Ith=50-63A,25kA,-4 NOS,MAKE L&Tor equivalent 3P,MCCB,Thermal Mag Rel,Ith=100-125A,25kA,-3 NOS,MAKE L&Tor equivalent CAPACITOR DUTY CONTACTOR 12.5 KVAR WITH 1 NO CONTACT,-2 NOS,MAKE L&Tor equivalent CAPACITOR DUTY CONTACTOR 25 KVAR WITH 1 NO CONTACT,-4 NOS,MAKE L&Tor equivalent CAPACITOR DUTY CONTACTOR 50 KVAR WITH 1 NO CONTACT,-3 NOS,MAKE L&Tor equivalent Aux.Contact block FIRST LEFT-1NO+1NC-MO C3-85,-9 NOS,MAKE L&Tor equivalent Aux.Contact block FIRST RIGHT-1NO+1NC-MO C3-85,-9 NOS,MAKE L&Tor equivalent Contactor Relay (4NO), AC Control,-3 NOS,MAKE L&Tor equivalent Contactor Relay (4NC), AC Control,-3 NOS,MAKE L&Tor equivalent Aux Contact block / MN0 DC,-6 NOS,MAKE L&Tor equivalent Aux Contact block / MN0 DC,-6 NOS,MAKE L&Tor equivalent 3Ph,4W,MFM -LED,240V,AC ,CL1,-2 NOS,MAKE L&Tor equivalent FUSE BASE BOLTED TYPE F1 CABLE 20A,-3 NOS,MAKE L&Tor equivalent CYLINDRICAL HRC FUSE LINK 16A,415V,50Hz,-3 NOS,MAKE L&Tor equivalent Metering CT 600/5A,5VA/1.0,-3 NOS,MAKE AEor equivalent LED INDICATOR DIA 22.5mm, RED,-1 nos,make L&Tor equivalent LED INDICATOR DIA 22.5mm, YELLOW,-1 nos,make L&Tor equivalent LED INDICATOR DIA 22.5mm, BLUE,-1 nos,make L&Tor equivalent AUTO/MAMUAL SELECTOR SWITCH W/O OFF,6A,-1 NOS,MAKE SALZERor equivalent TIMER 240 V AC 0.3 SEC-30 HRS,-1 NOS,MAKE L&Tor equivalent LED INDICATOR DIA 22.5mm, RED,-9 NOS,MAKE L&Tor equivalent LED INDICATOR DIA 22.5mm, GREEN,-9 NOS,MAKE L&Tor equivalent PUSH BUTTON ACTUATOR RED,-9 NOS,MAKE L&Tor equivalent PUSH BUTTON ACTUATOR GREEN,-9 NOS,MAKE L&Tor equivalent CONTACT ELEMENT 1NO,-9 NOS,MAKE L&Tor equivalent CONTACT ELEMENT 1NC,-18 NOS,MAKE L&Tor equivalent MAIN BUSBAR,400 AMP AL BUSBAR 4 POLE,-12 NOS PANEL-CRCA-POWDER COATED RATE FOR ABOVE CAPACTOR PANEL

Rubber mat, Rubber mat Supply of rubber mat 2 x 1.0Mtr, 1100V tested.

Spreading of metal dust, Collection and spreading of metal dust, murum and 40mm graded hard metal in sub-station yard or as required as mentioned below -Murum

Construction of pedestal (plinth) for transformer Designing and construction of pedestal (plinth) for transformer of desired size including excavation in hard rock/soft rock, base concrete M-7.5 (1:4:8), 20mm metal and pedestal of RCC M-15 (1:2:4) including required tar steel reinforcement for required height as per IE rules frombase concrete including shuttering and finishing with 10mm thick plaster in cement mortar 1:3 curing & white washing etc. complete as per specifications.

(DWC) Pipe Supplying and installing double wall corrugated pipes (DWC) of HDPE (IS 14930 Part II -marked) for cable laid underground with necessary material and at required depth upto 90cm. below road/ground surface, including excavation, back filling with excavated material, ramming and making the surface good.180.00mm outside dia.

G.I. Pipe Supplying & installing G.I. pipe for protection of underground cable fixed on wall/support/in trench/fixed between two rigid existing support of wall/beam for erection of ceiling Fan/down rod for stiff pendent for light luminaries /fan/protective for earthing, lightening conductor down strip/overhead service line/for submersible cable or centrifugal pump for water supply with necessary iron clamp coupler, bend, tee, elbow, nuts and bolts etc. complete in an approved manner as required to complete excluding cost of excavation/dismantling & other finished masonry Item complete.For 'A' class G.I. pipe ISI marked(IS-1161-69)80.00mm

Street light LED Supply and fixing street light with high power LED of 3 to 6 Watt each on existing bracket assembled on single MCPCB and additional unique peanut lens on each LED, system lumens output with efficacy120 lm/Watt. luminiare having color temp upto 6500K & 50000 hrs.burning life with minimum @ L 70, The colourrendering index of LED light should be more than 70. Luminiare comprises of driver, PF 0.95 & surge protection 10KV. Housing made of pressure die cast aluminium with heat resistantflat glass, IP65 protection. Submission LM 79- 08/IS16106 (2012), IEC60598, IEC61347 i/cconnection wire, testing etc. to complete the job. 90Watt, color temp 3000-6500k as required.

TPN MCB DB Supplying of approved make TPN MCB DB metal double door IP 43 protection with provision for FP MCB/ Isolator/ RCCB/ RCBO as incomer and SP MCBs as outgoing inclusive of busbar, neutral bar, earth bar,connection copper wire not less than 16 sq.mm & two earth terminals etc. complete as per IS:13032(exclusive of MCB & isolator):4 Way (4+12)

MCCB 3Ph, 3Pole Supply of ISI marked and approved make of moulded case circuit breaker (MCCB) suitable for 3 phase,3 pole, 50 Hz, 415 Volts, AC supply with respective interrupting capacity (KA) at 415 Volts cited against their range standard conforming to IS – 8828MCCB 25kA current rating, 3P -25 to 100Amp & 80% -100% adjustable

MCB 'D' Series Supply of ISI marked and accepted standard of miniature circuit breaker (MCB) of 'D' series with short circuit indication, suitable for 240/415 Volts,50 Cycle, 10 kA/15 kA Value AC supply conforming to IS : 8828 : 1996, IEC : 60898 :2002 & 60947-2 but without enclosures :-MCB SP 6Amp to 32Amp 10kA rating

Post top lantern Supply, fixing & testing of approved make globe type polycarbonate post top lantern, consisting of cast aluminium spigot complete with all accessories, lamp holder, (without lamp) including fixing on gate pillars/exiting G.I. pipe,pole with connection & all required materials on existing required size of G.I. pipe, suitable for CFL/LED lamp for mentioned below sizes :-300 mm (12")

Fire Extinguisher Supplying & fixing of fire extinguisher/refills as per IS specification ABC type duly refilled 6 Kg & ready to use

Buckets 4 buckets set with sand, self-supported M.S. stand i/c shed duly painted with redcolour as per IS.

Hand gloves Supply of hand gloves 33KV tested

XLPE insulated FRLS heavy duty power cable Supply of XLPE insulated FRLS heavy duty power cable conforming IS-7098 (Part-1) 1988, 1100 Volt grade, 2/3/4/8/10/12 core ISI marked with copper stranded/solid conductor. Armoured 2 core 2.5 sq. mm.

XLPE insulated FRLS heavy duty power cable Supply of XLPE insulated FRLS heavy duty power cable conforming IS-7098 (Part-1) 1988, 1100 Volt grade, 2/3/4/8/10/12 core ISI marked with copper stranded/solid conductor. Armoured 4 core 2.5 sq. mm..

XLPE insulated FRLS heavy duty power cable Supply of XLPE insulated FRLS heavy duty power cable conforming IS-7098 (Part-1) 1988, 1100 Volt grade, 2/3/4/8/10/12 core ISI marked with copper stranded/solid conductor. Armoured 8 core 2.5 Sq. Mm..

XLPE insulated FRLS heavy duty power cable Supply of XLPE insulated FRLS heavy duty power cable conforming IS-7098 (Part-1) 1988, 1100 Volt grade, 2/3/4/8/10/12 core ISI marked with copper stranded/solid conductor. Armoured 10 core 2.5 Sq. Mm..

XLPE insulated FRLS heavy duty power cable Supply of XLPE insulated FRLS heavy duty power cable conforming IS-7098 (Part-1) 1988, 1100 Volt grade, 2/3/4/8/10/12 core ISI marked with copper stranded/solid conductor. Armoured 12 core 2.5 Sq. Mm..

LT CABLE Supply of XLPE insulated power cable (conforming IS-7098 Part-I) 1100 Volt grade, 1 core/2 core/3½ core/4 core ISImarked with alu. stranded /solid conductor 3½ core armoured 25 sq. mm

LT CABLE Supply of XLPE insulated power cable (conforming IS-7098 Part-I) 1100 Volt grade, 1 core/2 core/3½ core/4 core ISImarked with alu. stranded /solid conductor 3½ core armoured 300 sq. mm

LT CABLE Supply of XLPE insulated power cable (conforming IS-7098 Part-I) 1100 Volt grade, 1 core/2 core/3½ core/4 core ISImarked with alu. stranded /solid conductor 4 core armoured 10 sq. mm.

LT CABLE Supply of XLPE insulated power cable (conforming IS-7098 Part-I) 1100 Volt grade, 1 core/2 core/3½ core/4 core ISImarked with alu. stranded /solid conductor 4 core armoured 16 sq. mm.

XLPE HT Cable Supply of approved high-tension XLPE cable (conforming IS-7098/II/85) as per ISI standard 3 core armoured with alu. solid/stranded conductor ISI marked asrequired.300 sq. mm.

Laying of one number armoured / unarmoured cable 1.1.KV grade of size exceeding 120 sq. mm. but not exceeding 400 sq. mm direct in ground including excavation in all soil/ murrum /soft rock, and sand cushioning protective covering and refilling the pit etc. as required.

DG set, Water cooled : Supply, installation, testing and commissioning of 'Silent Type' diesel generating set comprising with diesel engine water cooled, Synchronous alternator, AMF control panel single/three phase, acoustic enclosure, battery with charger and related accessories including PCC 1:2:4 platform, incoming cable 10 mtr, earthing Cu/GI plate 2No/2No, exhaust pipe 'B' class with insulation as per CPWD specification and CPCB -II Norms 3 Phase, 200 KVA, Water cooled : Supply, installation, testing and commissioning of diesel generating set three phase, water cooled with AMF control panel, 200 KVA, 415V. With electronic governor.