MP Laghu Udyog Nigam Limited Tender

Finishing walls with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Two or more coats applied on walls @ 1.25 ltr/10 sqm. over and including one coat of Special primer applied @ 0.75 ltr / 10 sqm.

Providing and laying vitrified floor tiles in different sizes with water absorption's less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 sand) including grouting the joints with white cement and matching pigments etc., complete.

Size of Tile 1000x1000x 10-12 mm

Size of Tile 600x600x9-10 mm

Providing and fixing tiled false ceiling of approved materials of size 595x595 mm in true horizontal level suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 gsm/sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38mm made from 0.30mm thick (minimum) sheet, spaced at 1200mm center to center and cross "T" of size 24x25mm made of 0.30mm thick (minimum) sheet, 1200mm long spaced between main "T" at 600mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600mm and size 24x25mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, wherever, required, cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 x mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications drawings and as directed by Engineer-in-charge.

12.5 mm thick fully Perforated Gypsum Board tile made from plasterboard having glass fibre conforming to IS: 2095 part I , of size 595x595 mm, having perforation of 9.7x9.7 mm at 19.4 mm c/c with center borders of 48 mm and the side borders of 30 mm, backed with non woven tissue on the back side, having an NRC ( Noise Reduction Coefficient) of 0.79, with 50 mm resin bonded glass wool backing.

Water proofing treatment over Roof, Wall, Chajjas, Balcony with Diamond Shield and Sealer coat or equivelent at leakage/ seepage area consisting of (i) Surface preparation roughening of surface, opening of cracks in 'V' groove in size of 5mmx10mm (WxD), filling of cracks with putty of Diamond shield with laying fiber glass mesh, Cleaning of surface by scrubbing with steel wire/ Nylon brush. Removing all dust particles and washing with adequate water to clean completely. (ii) Providing and applying 1st coat of diamond shield or equivelent (minimum thicknes 70-80 micron) (a two component flexible waterproof and protective modified mortar, dry powder 80% Chemical 20% acrylic resin having 30% solid contents) with mix proportion of Paart 1 and 2 with proper mixing with laying of fiber glass mesh (of weaving size of 10x10 yarn/inch duly coated with alkaline resistant polymer). Allow the coating to air cure for minimum 2 Hrs. (Diamond Shield or equivelent. After two hours minimum of 1st coat applying 2nd coat (minimum thickness 100 micron) of diamond shield or equivelent with mix proportion of part 1 and part 2 with proper mixing. Allow the coating to air cure for minimum 2 Hrs. Consumption of the diamond shild or equivelent should be @17.90 kg for 10sqm area. (After two coats of diamond shield, surface is to be cured properly minimum for 4 hrs.before application of third coat). (iii) Providing and applying 1st coat of sealer coat 50-60 micron (single component High build elastomeric, flexible, pure acrylic waterproofing membrans having solid content of 65%) and allow it to air cure for 4 Hrs minimum. After two hours minimum of 1st coat applying 2nd and final coat 120-140 micron of sealer coat and allow it to air cure for 4 Hrs minimum. Consumption of Sealer coar should be @ 5.40 kg per 10 sqm. area. (IV) The treated aarea should be cure with water for 48 hrs. by flooding the surface. (V) The final appearance of the coating will be milky white. All above operations to be done in order.

Dismantling of existing light / an / Bell / Socket out let point on separate board / Wiring and circuit with insulated wire in cassing / conduit / Batten complete with fitting and accessories.

Brick work with well brunt open bhatta, bricks, crushing strength not less than 25kg / cm2 and water absorpt ion not more than 20% in superstructure above plinth level and up to floor two level i/c curing etc complete. Cement mortar 1:4 (1 cement : 4 sand)

20 mm cement plaster of mix : 1:4 (1 cement : 4 sand)

Providing & fixing for base frame work for partitions / panelling on walls, column / beam etc by using ISI plywood frame work using two face finished 40mm x 36 mm section and 600mm c/c grid work i/c extra member at skirting level . Frame shall be treated with 5.0% dilute anti termite BISENTHRIN), emulsion sparayed with &. The frame work shall be fixed to wall with minmimun 100 mm fully thraeaded swcrew and PV rawl Plug . Frame work shall be fixed to wall in straight ling and proper plumb .Screw used in wall should properly fixed with M.Seal compound and rawl plugs.The job shall include all material labour, wastages etc. complete IS 3031989 Grade Plywood frame IS 303-1989 Grade Playwood frame

Providing and fixing decorative laminate as per ISwith marine grade PVA glue ( fevicol ) applied et 0 .45 kg per sq mtr to partition , paneling, roof beam or similar places as directed in design and pattern having pin groove . 1.0 mm thk plain, gloss, suede . Sation fifnish

Roller Blinds : Providing and fixing of vertical dust proof roller Blinds of approved shade texture and fabric with aluminium gear androlling arrangement, duly powder coated with all necessary mechanism complete in all respects and properly finished to the satisfaction of engineer in charge.

Table 2100 x 900 x 750 - Providing and fixing table of specified size to be made up of 18MM BWP ply as per drawing using approved make hardware, having a storage unit with three drawers as per given drawing. Provision has to be made for keyboard tray, CPU stand etc complete.

Providing and fixing wall storage to be made up of 18mm ply and laminatess as per drawing using approved make hardware, having a drawers, shelf and door as per given drawing etc complete.

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters of such as duro board, century or equivelant make. 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

Providing & Fixing of Height back chair Size: Height Overall/Seat - Max:1285/560mm, Min: 1185/460mm, Depth - 660mm, Width- 640mm: 5-Prong nylon base for stability. Twin Wheel heavy Duty Castor for easy mobility under load Hot pressed ply wood with steel T- Nuts for rigid fastening. Sturdy steel column gas lift for center: support and seat height adjustment. Telescopic ABS cover over steel column Lockable center tilt mechanism and with Single piece die castes PP arm rest. Quality Latherite tapestry with double stitch. High density PU cushion with latherite.

Providing & Fixing Premium Ergo visitor chair of Size: Total Height-840mm, Depth 600mm, Width-575mm Seat Height:450mm. Under Structure canti lever type MS CRCA Tube 1.6 mm thick. Hot pressed ply wood with steel T-Nuts for rigid fastening. Single piece integral skin PU arm rest. Quality tapestry. Seat and back covered with PP covers. High density PU molded cushion. All steel components are epoxy powder coated followed by seven tanks anti corrosion treatment of surface.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and Fixing of angle iron racks with shelf with M.S. Sheet with Powder Cotted etc Complete (Rack Size 900x2100x450mm)

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts and bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm or both sides of joint and two coats of primer suitable for board, all as per manufacturer’s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum moisture resistant board.

Providing & fixing for baseframe work for partitions / panelling on walls, column /beam etc by using seasoned and kiln dried wooden frame work using two face finished 40mm x 40mm section and 600mm c/c grid work i/c extra memeber at skirting level . Wood shall be treated with 5.0% dilute anti termite ( BISENTHRIN ), emulsion sparayed with &. The frame work shall be fixed to wall with minmimun 100 mm fully thraeaded swcrew and PV ravel Plug . Frame work shall be fixed to wall in straight ling and proper plumb .Screw used in wall should properly fixed with M.Seal compound and ravel plugs.The job shall include all material labour, wastages etc. complete B garde CP teak wood

Providing & fixing for partitions, panelling, on walls, column I beam etc by using dimensionally stable and wrap free ISI marked plywood / blockboard /mdf . Sheet work shall be fixed to base in straight ling and proper plumb using Screw used in wall should properly fixed with M.Seal compound and rawl plugs. The job shall include all material, labour, wastages etc. complete .Plywood Marine grade IS 710 9mm thk plywood

Providing and fixing decorative laminate as per ISwith marine grade PVC glue ( fevicol ) applied 0 .45 kg per sq mtr to partition , panelling , roof beam or similar places as directed in design and pattern having pin groove 1.0 mm thk textured finish

Providing and fixing clear heat reflective float glass to partitions, fix glazing, including polishing of edges and filling od gaps with silicon sealent as directed by engineer in charge 12.0mm thk

Extra for toughneneing and heat sheilding 12.0 mm thk

Supplying and fixing surface mounting LED down lighter, LED of 1 to 3 W each assembled on single MCPCB, having color temp 6500K & having 50000 burning hrs life with minimum @ L 70, system lumen output should be minimum with efficacy80lm/W. LED driver PF 0.95 & THD 20%. The colour rendering index of LED light should be more than 70. Housing made of CRCA powder coated frame with glare free diffused polycarbonate cover. Submission LM 80-08 Form LED Source Manufacturer & LM79-08 / IS16106 from NABL approved lab. Manufacturer mandatory. i/c connection wire, testing etc. to complete the job. 2 Yrs Guarantee certificate from manufacturer. 15 W , 180/200mm

Providing Split type air conditioner of capacity 2TR of make LG/Samsung/hitachi/panasonic or equivalent make 5 star BEE energy rating including installation.

Providing and fixing storage with size H-1200 x W-900 D-400 to be made up of 18mm ply and laminatess as per drawing using approved make hardware, having a drawers, shelf and door as per given drawing etc complete.

Specification-size-H-660 mm, L-1200 mm D-735mm, structure made of treated agro wood, fitted with 50mm wide rubberized belts 50mm wide with high density PU foam as per design, upholstered with premium quality PU cloth with help of stitching were ever necessary. Overall appearances as per photograph. Tapestry Mtr

Providing center table of size 1200x600x450 with glass top made of teak wood with polish etc complete.

Table Size:- 2200(W) x 1000(0) x 750(H)mm A) All tops shall be made of both side veneer faced MDF board 25mm thick and sides, drawer, shelves etc. of 18mm thick both side veneer faced particle board. B) The top shall have 90mm thickness all over the border with suitable reinforcement at bottom and teak wood beading, C) Mobile pedestal shall be of size 480(W) x 640 (D) x 600(H)mm. D) Back unit shall be of size 1000 (W) x 480 (D) x 750 (H)mm.

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations:a) Applying a slurry coat of neat cement using 2.75 kg/sqm. of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300mm height including cleaning the surface before treatment. c) After two days of proper curing applying a second coat of cement slurry using 2.75kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge.d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3mm deep.e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer-in-Charge : (with 5 years service guarantee) With average thickness of 120mm and minimum thickness at khurra as 65 mm.

Supplying, erection and testing of approved make electric Ceiling fan of double ball bearing complete with standard down rod, canopy, hanging shackle, Aluminium blades, without regulator, A.C. 230-250 volts including connections with all necessary material complete of approved as required confirming to IS :374/1979 with up to date ammendments.Ceiling Fan Ornamental (5 star)-1200 mm Sweep Ceiling Fan Ornamental (5 star)-1200 mm Sweep

Point wiring (excluding metallic switch box & sheet but including witches,sockes, lamp,holders,ceiling roses etc) with 1.5 Sq. mm. PVC insulated cable FR with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) 151 Marked of suitable size and LS Sq. mm. PVC insulated copper earth continuity conductor of green colour inside conduit etc. as required as per specification for :-

Light Point/Fan Points. Long point

:- Pin 6 Amp socket outlet on Separate Board Long point

Call Bell / Buzzer Points Long point

Twin Control light points Long Point

Point wiring (excluding metallic switch box & sheet but including switches, sockets) for 3 pin 6 Amp. Socket outlet point with 1.5 Sq. mm. PVC insulated cable ER with copper multi strand conductor ISI marked in concealed rigid F.V.C. conduit (HMS) ISI marked of suitable size and 1.5 Sq. mm. PVC insulated copper earth continuity conductor of green colour inside conduit with required materials as per specification on same board .

Wiring for circuit wiring with PVC insulated cable FR with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) of 151 marked suitable size etc. as required as per specification

a)2x2.5 Sq.mm.

b)4x2.5 5q.mm.

Point wiring (excluding metallic switch box & sheet ) for 3 Pin 16 Amp. Socket Outlet Point With 4 Sq. mm. PVC insulated cable FR with copper multi strand conductor ISImarked in Concealed rigid P.V.0 Conduit (HMS( 151 Marked of suitable size etc. with 16 Amp. F.T. Switch & Socket / S.S.Combinecl 6/16 Amp. of 151 Marked and 4 Sq. mm. PVC insulated copper earth continuity conductor of green colour inside conduit as per specification for On Separate Board

D.Extra Long —I

E.Extra Long —II

Same board switch socket 6/16 Amp

Supplying and fixing of approved make modular type metal box with modular frame/ base plate and cover plate including fixing in concealed / surface excluding switch,socket etc. as required for:-

6 Module

12 Module

18 Module .

Supplying of MCB Isolators suitable for 240/415 Volts, 50Hz AC supply with KA value rating 10 kA of approved make confirming to IS :13947-Part III : 1993 & IEC :60947- 3:2001 (without enclosures ) :-

SINGLE POLE 6 Amp to 32 Amp Rating

SINGLE POLE 40 AMPS

TRIPLE POLE 63AMPS

Supply of approved make powder coated sheet steel encloser SP N MCB DB inclusive of Bus bar, Neutral bar,Earth bar & two earth terminals etc. complete as per 15:13032( exclusive of MCB & isolator (-16 way Double Door IP 43 protection. 16 way Double Door IP 43 protection

Supplying and fixing of approved make step type Modular electronic Fan regulator including connection etc. as required on existing board 100 Watt (2 module)

Supplying and fixing recessed mounting LED down lighter, LED of 1 to 3 W each assembled on single MCPCB, having color temp 6500K & having 50000 burning hrs life with minimum @ L 70, system lumen output should be minimum with efficacy801m/W. LED driver PF 0.95 & THD 20%. The colour rendering index of LED light should be more than 70. Housing made of CRCA powder coated frame with glare free diffused polycarbonate cover. Submission LM 80-08 Form LED Source Manufacturer & LM79-08 /1516106 from NABL approved lab. Manufacturer manadatory. i/c connection wire, testing etc. to complete the job. 2 Yrs Guarantee certificate from manufacturer.15w LED15 W, 180/200mm

Suppling and drawing 4 pair shielded, 0.5 mm PVC.Insulated copper conductor un-armoured Cat-6 computer cable FR in existing surface / concealed ,steel / PVC. Conduit/Casing-NCapping as required.

Providing Split type air conditioner of capacity 1.5TR of make LG/Samsung/hitachi/panasonic or equivalent make 5 star BEE energy rating including installation.

Shifting, Installation, testing & commissioning of Split Air\Conditioning unit 1.0TR / 1.5 TR / 2 TR capacity including indoor/ out door unit complete as required

Supply, Installation, testing & commissioning suction/discharge copper pipe line in split Air Conditioning unit 1.0 /1.5 TR/2 TR /3 TR capacity including brazing, nitride rubber insulation, etc complete as required. Copper tube 5/8"

Earthing with Copper Earth plate 600mm X 600mm X 3mm thick including accessories and providing masonary encloser in cement mortor, cover plate having locking arrangement on the top and G.I. watering pipe 20mm dia 2.7 Metre long etc. (but without charcoal or coke and salt) complete as required.

Architect fees:- Drawing design planning and 3d view etc complete