Indo Tibetan Border Police Tender

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collectingsamples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level: All types of soil 300 mm dia:Rocky strata including Boulders 300 mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 150 mm nominal size dia.

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 150 mm nominal size dia

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any otherapproved method, measuring static level & draw down etc. by step draw down method, coll approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 150 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 150 mm clamp

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I).150 mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well, G.I Pipe and socketed etc of required dia, including painted with outside surface with two coats of anticorrosive bitumestic paint of approved brand and manufacture, including hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer -in-charge. 50 mm nominal size dia.

Supply and fixing of motor by 6mm dia stainless steel rope for anchoring of motor with all required accessories like hook, clamp etc complete as per direction of Engineer in charge.

Carrying out the resistivity survey by VES method using Schlumberger configuration for locating the proper spot with three soundings for drilling of tube well within the selected Habitation, including photography, interpretation of resistivity data and submission of report in the desired format along with resistivity readings, necessary graph and photographs

Supplying and installation of 1.1 KV grade 4 Sqmm 3 core Copper Conductor submersible cable from submersible pump to panel of make Poly cab/L&T/Havells/Finolex.Heavy Duty approved brand all as per requirement and direction of Engineer-in-charge

Providing and Installating Submersible Pump wet type induction motor of suitable RPM, 415 volt, 50 Hz, 3 Phase A.C. Supply, along with a directly coupled submersible elctric induction motor, water lubricated bearings, complete with all accessories in all respect - 1- Total head - 105-140 mtr 2- Discharge - 90-120 LPM 3- Reqd. HP & stage - 15-25stage, 4- Power : 5HP (As per pump manufacturer) 5- Outlet size :-50 mm 6- Type of Impellor- stainel steel 7- Make - Kirloskar/ crompton/WPIL/ Grondfos/Franklin /KSB/ISI approved make Note:- (1) The submersible set to be installed in the well with existing G.I Pipe, Lifting from existing borewell & lowering in new well with including cost of neccessery fittings i.e nut bolt, rubber gasket etc .(2) Pump shall be capable of operating under the water table/ draw down requirement.

Providing and Fixing Out door floor rested front operated, Starter panel as per the given specification fabricated from 14 SWG (2.0mm) M.S. SHeet for enclosure, Door, and partition as per rquirement of size HxWxD 800x800x300 mm, with powder coating RAL 7032 Shade suitable for 5HP SUBMERSIBLE pump with all inside fittings and connection required with submersible pump as per direction of Engineer incharge : MS Stand fabricated from MS Angle of (Size 35x5 mm) of hight 1000mm. - 01 No Copper Bus bar (size 30x3 mm) for main and connector of specified rating with color code heat shrinkable sleeves. :- 01 Set . MCB 63 A TP 10 kA :- 01 No MCB 32A TP 10 KA :- 02 Nos . Star Delta Starter suitable for 05 HP (MN 16) :- 02 NOs .LED type phase indication lamp :_ 01 set. 6 amp Control SP MCB:- 03 Nos. Digital multifunction lamp :- 01 No Digital Amphere meter :_ 02 Nos Digital Voltmeter - 02 Nos Single phase preventer - 02 Nos Current Transformer meter 60/5 5 VA Class I :- 03 NosTringular Type Door locks with key - 01 No Concealed Hinges Wiring (Single Core multi Strand copper wire of respective currents ratings) Lugs and other insulation : - As required MCB Channel and terminal block and PVC channel for wiring Other Miscelleneous hardware

Earthing with G.I. earth plate 600mmx 600mmx 6mm thick including accessories and providing masonry enclosure with cover plate having locking arrangment and watering pipe of 2.7 meter long etc with charcoal/ cock and salt as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Providing and fixing 25mmx5mm G.I strip in 40 mm dia G.I pipe from earth electrode including connection with G.I nut, bolt, spring, washer, excavation and re-filling etc as required.