Food Corporation Of India Tender

Supplying / Installation / Testing and Commissioning of LED Tube rod 20 Watt cool white or similar with in built driver 20W with 2100 Lumens of make of reputed brand under MII confirming to IS and IEC codes respectively in the existing box type or street light fitting after disconnection of choke and starter and providing connector with wiring and connection etc as required directly on wall with round block as approved by Engineer In Charge

Supplying and fixing of out door type loop in loop out cable junction box fabricated from 1.6 mm MS sheet enclosed wheather proof, dust proof, water proof and locking arrangement internally embedded gasket with bottom cable entry plat through cable glands fixed with clamps on steel structure and wall. Seperate for incoming and out going cables and wires duly fitted with following in it. HD Connector for 10 to 16 sqmm - 4 Nos. 6 amp SP 'C' curve 10 KA MCB - 1 No. fixing Clamps - 2 Nos.

Supplying and fixing of 32 mm dia X 2.00 metres long G.I. pipe (medium class) bracket for mounting of all type of street light fitting on pole / wall / structure including bending the pipe to the required shape, 2 nos 40 mm X 3 mm flat iron clamps with nuts, bolts and washer, painting the flat iron with primer and finish paint etc. as required.( DSR-2022 12.34)

Supplying and fixing of 32 mm dia X 1.00 metres long G.I. pipe (medium class) bracket for mounting of all type of street light fitting on pole / wall / structure including bending the pipe to the required shape, 2 nos 40 mm X 3 mm flat iron clamps with nuts, bolts and washer, painting the flat iron with primer and finish paint etc. as required.( DAR-2022 12.34)

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.((DSR-2022 It.1.41))

Supplying and fixing following way, Single pole & Neutral, Sheet Steel MCB Distribution Board 240 Volts, on surface / recess, complete with tinned copper busbar, neutral bus bar, earth bar, din bar interconnection,powder painted including earthing etc. as reqd. (But without MCB's / RCCB / Isolator).

a) 8 Way Double Door

Supplying and fixing following piano type switch / socket on the existing switch box / cover including connections etc. as required

a) 5 /6 amps Switch

b) 3 pin 5/6 A Socket Outlet

Supplying and drawing sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel / PVC conduit as required.

a) 3X 1.5 sq. mm

b) 6 X 1.5 Sq mm

c) 3x4 Sq mm.

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.

i) 20 mm

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

15/16 amps Switch (DSR-2022 It.1.24.3)

6 pin 15/16 A Socket Outlet (DSR-2022 It.1.24.5)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.

i) 1 or 2 Module (75mmX75mm)

ii) 8 Module (125mmX125mm)

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, “C” curve, miniature circuit suitable for inductive load of following poles in the existing MCB DB complete with connection, testing and commissioning etc. as required(DSR 2022)

Single pole MCB ( DSR-2022 2.10.1)

Single pole & Neutral MCB( DSR-2022 2.10.2)

Supplying of XLPE insulated & PVC tape innersheathed aluminium conductor armoured cable of 1.1 KV grade of following size confirming to IS:7098 (Part- I) 1988 with up to date ammendment as required.

4 x 16 sqmm

3.5 x 35 sqmm

4 x 25 sqmm

2 x 10 sqmm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of size up to 35sqmm in the existing masonry open duct as required.

Size not exceeding 35 sqmm(DSR-2022 7.6.1)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade wall or steel structure surface as required.

Upto 35 sq. mm (clamped with 1mm thick saddle)(DSR-2022 7.7.1)

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required.

Upto 35 sq. mm(DSR-2022 7.1.1)

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size in the existing RCC/ HUME/ METAL / HDPE pipe as required.

Upto 35 sq. mm(DSR-2022 7.5.1)

Supplying and fixing of light class G.I. pipe of following dia. (nominal) along the pole or surface of wall for protection of under ground cable as required.

50 mm Dia.(DDSR)

Supplying and making end termination with brass compression gland and aluminium lugs for 2 x 10 sq mm (19 mm) size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

2 X 10 sq. mm (19mm) (DSR-2022 -9.1.2)

4 X 16 sq. mm (28mm)(DSR-2022 -9.1.33)

4 X 25 sq. mm (28mm)(DSR-2022 -9.1.34)

3.5 X 35 sq. mm (32mm)(DSR-2022 -9.1.21)

Supplying & Fixing of 4 way busbar chamber of make of reputed brand under MII confirming to relevant IS and IEC codes , confirming to IEC-61439-3 / IS-8623 & IEC-60529 / IS-2147of size not less than 400X300X150 and is fabricated using sheet steel (CRCA) and epoxy powder coated to give superior & lasting finish. The bus bar sections are made of ETP grade copper & dull tin plated and the bus bar supports are made of DMC (Dough moulding compound). Left & Right side end plates are detachable. of following capacity and fixing, earthing the body etc. along with necessary connections as required

a) 63 Amp (on pole / wall)

Supply and fixing SS Enclosures for MCCBs (but without MCCB) of of make of reputed brand under MII confirming to relevant IS and IEC codes of suitable size to accommodate MCCB DU100D along with accomodation for Al. armoured cable upto 70 Sq. mm. and upto 125A MCCBs, 36kA with IP30 and IK 08 protection as required.

Supply of following capacity MCCBs of L&T make conforming to IS/IEC 60947-2 & IEC 60947-2,four pole, compact size having an adjustable overload setting suitable to get fitted in the SS MCCB enclosure as mentioned at item no. 23 as reqd:

a) 63 Amp MCCB 4 pole Cat Ref: DU100D of L&T make

Supply and installation of CRCA Enclosure single door system of 400mm* 400mm* 200mm (W*H*D) Fabricated from 2.0 mm CRCA sheet steel powder coated, mounting plate made up of 2mm galvanised steel, IP 65 protection, foamed in PU gasket, 110 deg door openable concealed hinge door with locking arrangement, i/c and o/c cutouts at bottom for cable with rubber bush, with a set of wall mounting brackets and supply/ installation of double pole 25A MCB with installation of Auto photo switch inside enclosure with all required internal and external wire connections.

Supply of automatic light controller device with 25A load capacity, 230VAC±10% system voltage, 50Hz indoor unit with photo sensor cell along with wire of 5m length for sensing device, with adjustable lux intensity, LED indication, Powder coated sheet metal enclosure for outdoor application. Warranty of 1 years is mandatory.

Providing & Fixing 10 SWG dia GI Wire in open duct alongwith the existing cable as reqd.

Supply, Installation, testing & commissioning of cubicle type totally enclosed free standing type moisture, dust and vermin proof Panel Board made out of 2.0 mm thick CRCA sheet Steel IP 42 floor mounting type and the same will be installed in ground at a height of 200 mm using MS Angle base frame suitable size of 50 mm x 50 mm x 3 mm size angles with necessary CC foundation with minimum dimension of 1200 mm(H) X 1000 mm (W) X 300 mm(D) fabricated in compartmentalized design. The sheet steel shall undergo minimum 9 tank treatment followed by finishing powder coating of min 60 micron thickness. the board includes 415 V electrolytic, 400 Amp (each strip) 04 nos Aluminium Bus Bar, removable gland plates, cable glands, including connection with outgoing feeders complete in all respect. All MCCB shall have thermal magnetic release with adjustable over current, short circuit & Earth fault protection with trip history (Faulty phase, type of fault and interupted Current). All MCCB's shall be ics = 100% Icu, with rotary handle & pad locking arrangement, with adjustable O/L & S/C trip setting as per load requirement. All TP MCCB shall be with solid isolable neutral link. The breaking capacity specified is Ics value. All outgoing MCB's shall be C type with 10 KA breaking capacity. The fault withstanding capacity of panel shall be 25 KA rms for 1 sec. The above board shall be complete with 3 nos. phase indicating lights, flush AVF meter with, CT's, PT's, selector switches, protective fuses etc. at Incomer with all inter connections by min. 6.0 sq.mm. Copper wires alongwith switchgears as mentioned below: Incoming 01 Nos of 200 Amp FP Moulded Case Circuit Breaker. (36 KA) (Conforms to IS/IEC 60947-2) Outgoing 01 Nos of 125 A Amp FP Moulded Case Circuit Breaker. (36 KA) (Conforms to IS/IEC 60947-2) 01 Nos of 40 Amp FP Moulded Case Circuit Breaker. (30 KA (Conforms to IS/IEC 60947-2) 01 Nos of 50 Amp FP Moulded Case Circuit Breaker. (30 KA (Conforms to IS/IEC 60947-2) 06 Nos of 32 Amp DP Miniature Circuit Breaker. (10 KA (Conforms to IS/IEC 60947-2) 01 Nos of 63 Amp FP Moulded Case Circuit Breaker. (30 KA (Conforms to IS/IEC 60947-2)

Supplying, Installation, Testing & Commissioning of out door wall mounted type section pillar of minimum size 1200mm X 600mm x 400mm suitable for 415 V, 3 Phase, 4 Wire 50 Hz AC supply system fabricated from CRCA sheet steel of 2 mm thick for frame work and covers, 3 mm thick for gland plates i/c cleaning & finishing complete with 7 tank process for powder coating in approved shade and shall be dust proof, verm proof, water proof, removable cobers, gasketed and seperate removable gland plate, having 400 Amp ( 04 nos strips) capacity extensible type TPN Aluminium Alloy bus bars of high conductivity, DMC/SMC bus bar supports, with short circuit withstand capacity of 31 MVA for 1 Sec., & common GI earth bar of size 32 mm x 5 mm at the rear with 2 Nos. earth stud, solid connections from main bus bar to switch gears with required size of Al. bars and control wiring with adequate size PVC insulated copper conductor S/C cable, mounting on MS angle base frame of required size and the same will be installed in ground with necessary CC foundation alongwith Incoming 1 No of 125 Amp FP Moulded Case Circuit Breaker. (36 KA)(Conforms to IS/IEC 60947-2) Outgoing 1 No of 40 Amp FP Moulded Case Circuit Breaker. (36 KA)(Conforms to IS/IEC 60947-2) 1 No of 40 Amp FP Moulded Case Circuit Breaker. (30 KA)(Conforms to IS/IEC 60947-2) 1 No of 40 Amp FP Moulded Case Circuit Breaker. (30 KA)(Conforms to IS/IEC 60947-2) 1 Nos of 63 Amp FP Moulded Case Circuit Breaker. (30 KA) (Conforms to IS/IEC 60947-2) 04 Nos of 32 Amp DP Miniature Circuit Breaker. (10 ΚΑ) (Conforms to IS/IEC 60947-2)

Supplying, Installation, Testing & Commissioning of out door wall mounted type section pillar of minimum size 600mm X 600mm x 400mm suitable for 415 V, 3 Phase, 4 Wire 50 Hz AC supply system fabricated from CRCA sheet steel of 2 mm thick for frame work and covers, 3 mm thick for gland plates i/c cleaning & finishing complete with 7 tank process for powder coating in approved shade and shall be dust proof, verm proof, water proof, removable cobers, gasketed and seperate removable gland plate, having 100 Amp ( 04 nos strips) capacity extensible type TPN Aluminium Alloy bus bars of high conductivity, DMC/SMC bus bar supports, with short circuit withstand capacity of 31 MVA for 1 Sec., & common GI earth bar of size 32 mm x 5 mm at the rear with 2 Nos. earth stud, solid connections from main bus bar to switch gears with required size of Al. bars and control wiring with adequate size PVC insulated copper conductor S/C cable, mounting on MS angle base frame of required size and the same will be installed in ground with necessary CC foundation alongwith Incoming 1 No of 50 Amp FP Moulded Case Circuit Breaker. (36 KA)(Conforms to IS/IEC 60947-2) Outgoing 2 No of 32 Amp FP Moulded Case Circuit Breaker. (36 KA)(Conforms to IS/IEC 60947-2) 04 Nos of 32 Amp DP Miniature Circuit Breaker. (10 ΚΑ) (Conforms to IS/IEC 60947-2)

Earthing with G.I. earth plate 600mm X 600mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required.

The items are to be dismentalled where the work has to be executed and take away by the giving the credit to the work estimate

Angle and chanel iron, MS clamp, Iron material etc

The items are to be dismentalled where the work has to be executed and take away by the giving the credit to the work estimate

Lighting fixtures, cable, wires etc.