Advanced Materials And Processes Research Institute Tender

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand(zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources).

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Centering and shuttering including strutting, propping etc. and removal of form for : Lintels, beams, plinth beams, girders, bressumers and cantilevers

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.Using M.S. angels 40x40x6 mm for diagonal braces

Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Painting on G.S. sheet with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :New work (two or more coats) including a coat of approved steel primer but excluding a coat of mordant solution

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.. In cement mortar

Providing and fixing P.V.C. low level flushing cistern with manuallycontrolled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete.10 litre capacity - White

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.Flexible pipe 32 mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. :Concealed work, including cutting chases and making good the walls etc. 32 mm nominal outer dia .Pipes.

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. : External work 50 mm dia. nominal bore

Providing and fixing brass bib cock of approved quality : 15 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions :45 cm length 15 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and applying multicoat synthetic plaster as per approved design, pattern texture in 3 mm thick on plastered surface finished in proper line and level as directed by Engineer-in-charge in five coats consisting of composition of four order of application given as under includig all materials, labour and scaffoldings etc. 1) Scrapping of the new surface and applying sealer primer mixed with water in the ratio 1:3 (part sealer primer : 3 part water) and applying by brush @ 0.25 kg/sqm. 2) Applying levelling coat of spectrum rustic fine or equivalent with trwel as a putty finished to generate required texture by trowel. 3) Applying third coat of synthetic plaster with trwel @ 2.5 kg/sqm finished to generate required texture by trwel. 4) Applying two coats of exterior super fine pigmented acrylic wall coating external ACE/APEX as top coat @ 0.5 kg/sqm in two coats and colours as approved by Engineer-in-charge all up to a height of 10m

Providing and fixing under cabinet in exiting structure with doors of required size in symmetry and soft close hinges of make GODREJ/ EPCO/ BLUM and other fittings including handles 100 mm long , as needed and plyboard/blockboard 16mm of approved make and mica 0.75 mm on front and balancing laminication on back. The under cabinet of the platform will be made of ply board with mica on top with fitted with hinges including all fittings and fixtures etc. complete.as required as per site requirement and instruction and decision of E-in-c. Line drawings is included and for any query related to this item site visit may be done and E-in-c may be contacted if required.

Repairing of sliding gate including removing pipe, laying pipe to water level, welding bar rod to C-chanel, changing bearings including welding, fabrication, changing required parts/wheels and other required civil work as required as per site condition to make gate smooth for working

Fixing SS Railing in pipe of required dia including grouting pipe in cement and making hooles in tiles by suitable arrangement including fixing 30 cm granite 16 mm thick by sitable adhesive/cement as per site condition and fixing by araldite/adhesive in double railing

Fixing square jali in 30mmx30mm square pipe frame to stop incoming of creatures from entring inside shed at the height of minimum 60 feet no extra payment will be made for scaffolding

P/f aluminium partition in aluminium section medium gauge with 4mm glass / 12mm board ISI marked including fitting with clip, rubber as required with screws, handles, door stopper hinges, L-drop etc all fittings and fixtures as required and desired by E-in-C.

Providing and fixing aluminium sliding door bolts, ISI marked anodised transparent or dyed to required colour or shade, with nuts and screws etc. complete :250x16 mm

Providing and fixing aluminium tower bolts, ISI marked, transparent or dyed to required colour or shade, with necessary screws etc. complete :300x10 mm

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised transparent or dyed to required colour and shade, with necessary screws etc. complete.Single rubber stopper

Design and providing and fixing tensile shed with suitable M/s pipe sturcutre as per design and cover with egg white tensile fabric ferrari make 762 GSM with water chanel etc. complete as per E-in-C

Providing and fixing Security Cabin of size 8’x10’x10’ (in foot) including fabrication and erection etc complete as per site requirement ant instruction of E-in_C as per following Base Frame: The Base Frame Shall Be Made Out Of Suitable MsSteel C Channels, L Angles, Rectangle & Square Hollow SectionsTubes. Crane Hook Provision Shall Be Provided In All Corners ForEasy And Safety Lifting. Floor: Ms Structure As The Base With 16Mm Bison Board/HDMR Board On TheTop. The Board Shall Be Covered With 1Mm Thick Vinyl Sheet. Walls: The Walls Shall Be Consisting Of Sandwich Puf Panel WithTcp Color Coated Gi Sheet Having 0.40 Mm Thickness From InsideSkin And Outside Skin As Well, With Insulation Material Of FireRetardant, Self Extinguishing And Cfc Free Polyurethane Foam(Puf) Embedded Between The Two Through Injection MoldingProcess. Total Thickness Of Wall Panel Shall Be 40 Mm. Roof: The Roof Cladding Shall Be Made Of Sandwich Puf PanelWith Tcp Color Coated Gi Sheet Having 0.40 Mm Thickness FromInside Skin And Outside Skin As Well, With Insulation Material OfFire Retardant, Self Extinguishing And Cfc Free Polyurethane Foam(Puf) Embedded Between The Two Through Injection MoldingProcess. Total Thickness Of Roof Panel Shall Be 30 Mm. Door: Main Door (D): 02 No – Size in feet – 3'(L) X 7' (H) Shall Be Made WithSandwich Puf Panel Of Thickness 40Mm (Same As Wall) &Supported With Steel Channels And Finished With Cylindrical Lock,Door Closure And Necessary Hardware's.Window: 3 No's Sliding Windows (Size in feet- 4' (W) X 3' (H)) Shall BeMade Out With 4Mm Plain Glass & NecessaryHardware's As Described In The Drawing. All Windows Shall HaveCanopy And Safety Grills.Sanitary: 01 No Ewc Closet With Flush Tank, And 01 No 2 In 1 Tap With Hand Shower Will Be Provided With Necessary Outlet Pipes With Provision For Water Drain Out. 1 No Ss Sink With Tap Shall Be Provided In Pantry As Per Drawing. Electrical: The Unit Shall Be Completed With All The ElectricalFittings By Concealed Wiring as per IS standards, 1 No Bulk Head Fitting, 2 No's LedTube Light Fitting, 5 No's 5 Amp Power Socket, 1 No's Cabin Fan 2 No Exaust Fan And 01 Number Mcb With Necessary Switches, Sockets And Db's 2 core aluminium cable appromiate 50meter. Painting: The Expose Ms Structure Shall Be Painted With OneCoat Primer And Two Coat Enamel Paint in desired colour as per instruction of E-in-C.

Providing and laying 60mm thick factory made rubber moulded cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of stone dust filling the joints with fine sand and sides shall be all complete as per the direction of Engineer-in-charge.

Providing and fixing readymade PVC septic tank of suitable capacity including earthwork in excavation for tank and pipes and and filling the excavated area by suitable means including making arrangement for overflow in a soakpit of suitable size to soak grey water. (Tank capacity 1000 liters)

Providing and fixing brass FABT to Metropole push valve/ other fitting in 32mm dia with all accessries fittings and fixutres complete as per direction and instructon E-in-charge.

Providing and fixing Brass Ball cock of approved quality and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball.

Providing and fixing pressure pump of suitable head for lifting/ supplying water upto a height of 20m 1Hp including making arrangement for security in outdoor by a suitable shed made up of profile sheet and complete encloseure suitable for all seasons with locking arrangement including rainy season. The pump will be fixed in existing water pipe line as a booster pump thus suitable arrangement for plumbing requirement includes cutting and fixing of pipes and all plumbing acessories fittings whatever required for smooth functing of pump with suitable electrical connection including MCB, Cable to the nearest point and making all required connection for full functioning.