Rural Development And Panchayati Raj Department Tender

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and panelling to be paid for separately): Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and panelling to be paid for separately): For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade 1 Type II in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm)

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimetre channels 0.5 mm thick 27 mm high having flanges of 20 mmand30mmlong,theperimetre of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimetre channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimetre channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

Providing and laying 200mm thick mud pushka over talboos with 5mm thick dry grass (Yakzes/spoto/dry paddy straw etc), including ramming at OMC

Providingwoodworkinframesofdoors,windows,clerestorywindowsandother frames,wrought framedandfixedinpositionwithholdfast lugsorwithdash fastenersofrequireddia&length(holdfast lugsordashfastenershallbepaid for separately). Second class Kail wood

Providing and fixing 12mm thick plywood T&G wall panelling including polishing complete job.

Providingandfixingpanellingorpanellingandglazinginpanelledorpanelledand glazedshuttersfordoors,windowsandclerestorywindows(Areaofopeningfor panel inserts excluding portion inside grooves or rebates to bemeasured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick :

Providingandfixingpanelledorpanelledandglazedshuttersfordoors,windows andclerestorywindows fixingwithbutthingesof requiredsizewithnecessary screws,excludingpanellingwhichwillbepaidforseparately,allcompleteasper directionofEngineer-in-charge.(Note:Butthingesandnecessaryscrewsshallbe paid separately)

20 mm cement plaster of mix :1:4 (1 cement: 4 fine sand)

Providing and applying plaster of paris putty of 2mm thickness over plastered surface to prepare the surface even and smooth complete.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including priming coat with water thinnable cement primer

French spirit polishing, Two or more coats on new works including a coat of wood filler

carriage of cement and steel from an average distance of 110 km by M.T

carriage of stone from an average distance of 10 km by M.T

carriage of sand and aggregate from an average distance of 10 km by M.T

Wiring for light point , fan/ exhaust/call bell point/ amp socket point with 15 mm FR/PVC insulated copper cable in existing /recessed PVC conduit but without control switch, without box as required.

wirring for 16Amp socket outlet with 2.5mm FR/PVC insullated copper conductor cable in existing recessed pvc conduit including sheet as requried .

Supplying and fixing 0f 1 inch, ¾ inch pvc conduit capping along the accessories in surface / recessed including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing of 10 amp 240 volt single pole grid plate mounted switch indicator with molded copper plate including recessed 2 inch ms box complete as required including connection.

Supply and fixing of combined 3 pin 240 volt 20amp socket outlet with safety shutters and 20amp 240 volt single pole mounted in recessed including m.s box complete as required

Supply and fixing of combined 3 pin 240 volt 10 amp. Socket outlet with safety shutter and 10 amp. 240 volt single pole mounted in recessed including complete MS box complete as required

4 modular plate

6 modular plate

12 modular plate

Supply and fixing of MCB of following poles in the existing MCB DB complete with connections testing and commission etc, as required. Single pole 6/10/20amp

Supply and fixing of MCB of following poles in the existing MCB DB complete with connections testing and commission etc, as required. Double pole 63amp

Supplying and fixing of the following light fixture including all accessories like electronic ballasts comes etc. complete as required concealed / tube lightning LED luminaries as per Philips.

Supply of 11000 volt grade aluminium conductor KPLE insulated PVC sheath arramged complete as per specification as required 25 mm 3 core

Supply and fixing single pole and neutral sheet steel mcb distribution box 240 volt on surface recess complete with tinned bus bar neutral link earth bar, tin bar, detachable glaud plates, double door interconnected including points etc. as required 16way double door spn

wirring for 63amp for change over including fitting complete