Public Works Department Tender

c)Aux

d)3rd

e)4th

f)6th

g)8th

h)Rear main

i)Aux

j)3rd

Repair to propeller shaft with P/E of teeth assy centre bearing, oil seals, U cross holder, yoke rubber coupling set, rear shaft pinion bearing. The job includes cost of material and labour charges.

Complete F.I.P overhauling of the vehicle the job includes cost of material and labour charge.

Complete overhauling of the pump (Rotatory) aldo P/F or TRV bush set, vain pump, new injector nozzles 6Nos. Complete job.

M-Oil change of the vehicle for by the way of P/F of new oil filters and diesel filters also flushing of the engine with K-Oil complete job. (Excluding cost of M-Oil)

Changing of the gear oil,differential oil and power steering oil complete. The job also includes cost of gear oil, steering oil and labour charge

Repair to the clutch system by providing and fitting of new clutch plate, pressure plate assy. Clutch release bearing assy etc. The job also includes cost of labour and material charges.

Differential checking providing and fitting of crown wheel complete set, star kit , handle, pinion bearing also change of differential oil complete, also gear oil changes by way of servicing of the gear box complete. The job also includes cost of material and labour charges.

Providing and fitting of new booster set to the vehicle by the way of replacement of old damaged unserviceable.

Cylinder head checking and repairing by way of providing and fitting of engine valve seats in cyclinder head for proper lapping, providing and fitting of valve guide with valve operating rods and fitting of valve guide with valve operating rods and fitment with engine. The job includes the cost of boring of cylinder, lining and polishing of the engine cylinders etc. (complete job)

Complete four wheel checking of the vehicle by way of replacement of damaged front wheel bearing, brake shoelining of four wheel, greasing of wheels etc.complete job

Complete denting and painting of the front body of the vehicle. The job includes setting of the door by way of denting and body packings. Complete job. The job also includes complete wiring and P/F front head lights. Bumper etc. Complete job

Repair to the radiator by way of flushing acids and soldering where required, providing and fitting of radiator mounting one stretch support, hosepipe set with clamos, replacement of water pumps assy with providing and fitting of seal kit.Complete servicing of radiator.

Providing and fitting of 2nd and 3rd gear to gear system also main shaft bearing, gasket set. Also providing of gear oil and oil seals. Complete job.

Repair to the suspension system by way of retensioning of the leaf spring assy, replacement of broken leaves, centre bolt, shackle assy, pins,U bolt. Complete job.

Repair to self P/F of self armature, copper bush, shaft bush, rocket plate and wire repair

Repair to alternator 12v by P/F rotter, rectifier plate, cutout, carbon bush and battery terminal

Repair to the battery by repair to the poles and replacement of electrolyte and full charging of the battery.

Repair of complete wiring by providing and fitting of back light switch, indicator switch. The job include cost of material and labour charge.

Providing and fitting of black rubber pipe water tankers for supply of water through tankers to the public at different points inLeh Block. A) 3 inch dia black rubber pipe.

b) 1.5 inch dia black rubber pipe

Providing and fitting of 1020 tyre (RIB) including Tube and flap dimension of 20 inch, Tyre- tube, tyre size 1020. Make MRF, CEAT, YOKOHAMA, JKTYRE or any other equivalent.

Providing and fitting of 1020 tyre (lug ) including Tube and flap dimension of 20 inch, Tyre- tube, tyre size 1020. Make MRF, CEAT, YOKOHAMA, JKTYRE or any other equivalent.

Providing and fitting of 12v battery of 150 AH of luminious, exide amaron.

Denting of water tankers including setting of the door, windows, body packing and other parts wherever required. Painting of whole water tankers includes painting writing with synthetic enamel paint of approved brand. The job includes complete wiring, front head light, back light, indictor switch and fibracation of seat cover ( incl cost of material and labour charge.)

Repair of water tankers by way of fabrication for fuel tank safety Guard, Air tank safety Guard, back safety guard, Railing on back side Mud- Guard on both side stairs. The job also includes Dismentalling and reassembling, of fuel Tank, Air Tank, other parts of vehicles during fabrication. including cost of material and labour charge.

Supply, Installation, testing and commissioning and extraction and lowing 2HP of Dual Solar Submersible pump Set in 5" dia tube well for clear and cold fresh water with latest amendments from the tube well with complete accessories of the following specification iv.Type of Pump and Capacity= 10submersible 2HP v.Capacity of pump in LPM Minimum= 90LPM vi.vi.Total Dynamic head of the Pump= 50Mtr b)PUMP: The pump shall be multistage centrifugal pump with radial or mixed flow type impeller design, Suitable for handling clean to slightly contaminated water with permissible sand content, Epoxy coated treatment to all ferrous parts for rust prevention and longer life, Non return valve fitted to discharge outlet to preventionback flow, Dynamically balanced impellers with shaft for better efficiency and performance.SS-304 or higher as required. c)Junction Box: Junction box with hinged, wheather proof lid, captives screws, three cable glands entry points and one cable gland (Standard)-IP65 protection d) The motor should be water cooled and provided with Submersible flat cable of Sheathed copper conductor with water proof PVC of standard and reputed make as per site requirement. Cable with conductor size depending upon array current will be provided from PV array to control panle and cable must be as per IS 694 or IS9968 e)The erection clamps shall be suitable for installing the submersible pump in the tube well and holding it for the column pipe of required dia. f)GI Coulm pipe Flanged ended (Class-B) of 3mtr length (HOT DIP galvanised IS 4759) and as per the dia of the delivery size and length as per site requirement. g) Lowering of Submersible Pump set in 200mm dia bore well up to the require depth by coupling with GI column pipe flanged ended (Class B) of 3mtr length each along with Submersible cable. The GI column pipes are to be join together by using jointing gasket and nuts and bolt of suitable size and fabrication and fitting of errection clamps to hold the pumping assembly/unit intact while extracting the fresh water from tube well. The job also includes installation and testing of the Submersible pump set on full load at site and cutting of casing pipe 200mm from BGLto 1.8 mtr deth including excvation of earth as directed by Site Engineer. h)Earthing arrangement: Earthing in accordance with IS 3043 for controller, pump and SPV Array. i)A lightnibng arrestor shall be provided with every SPV Water pumping system. J) The control panel shall be GSM based with button operated for motor on solar and grid. (One complete job including a toh) The rate also includes maintenance of the Solar Submersible pump set for a 5years. Cable must beas per IS694 or IS9968 and as under IP65 protection. AC/DC switch as per IS/IEC 60947-I, suitable for power on and power off shall be provide in SPV pump controller.

Supply, Installation, testing and commissioning and extraction and lowing 3HP of Dual Solar Submersible pump Set in 5" dia tube well for clear and cold fresh water with latest amendments from the tube well with complete accessories of the following specification Type of Pump and Capacity= submersible 3HP Capacity of pump in LPM Minimum= 90LPM .Total Dynamic head of the Pump= 70Mtr b)PUMP: The pump shall be multistage centrifugal pump with radial or mixed flow type impeller design, Suitable for handling clean to slightly contaminated water with permissible sand content, Epoxy coated treatment to all ferrous parts for rust prevention and longer life, Non return valve fitted to discharge outlet to preventionback flow, Dynamically balanced impellers with shaft for better efficiency and performance.SS-304 or higher as required. c)Junction Box: Junction box with hinged, wheather proof lid, captives screws, three cable glands entry points and one cable gland (Standard)-IP65 protection d) The motor should be water cooled and provided with Submersible flat cable of Sheathed copper conductor with water proof PVC of standard and reputed make as per site requirement. Cable with conductor size depending upon array current will be provided from PV array to control panle and cable must be as per IS 694 or IS9968 e)The erection clamps shall be suitable for installing the submersible pump in the tube well and holding it for the column pipe of required dia. f)GI Coulm pipe Flanged ended (Class-B) of 3mtr length (HOT DIP galvanised IS 4759) and as per the dia of the delivery size and length as per site requirement. g) Lowering of Submersible Pump set in 200mm dia bore well up to the require depth by coupling with GI column pipe flanged ended (Class B) of 3mtr length each along with Submersible cable. The GI column pipes are to be join together by using jointing gasket and nuts and bolt of suitable size and fabrication and fitting of errection clamps to hold the pumping assembly/unit intact while extracting the fresh water from tube well. The job also includes installation and testing of the Submersible pump set on full load at site and cutting of casing pipe 200mm from BGLto 1.8 mtr deth including excvation of earth as directed by Site Engineer. h)Earthing arrangement: Earthing in accordance with IS 3043 for controller, pump and SPV Array. i)A lightnibng arrestor shall be provided with every SPV Water pumping system. J) The control panel shall be GSM based with button operated for motor on solar and grid. (One complete job including a toh) The rate also includes maintenance of the Solar Submersible pump set for a 5years. Cable must beas per IS694 or IS9968 and as under IP65 protection. AC/DC switch as per IS/IEC 60947-I, suitable for power on and power off shall be provide in SPV pump controller.

2HP control panel/VFD panel shall be fullyautomatic with button operatrd for motor on solar and gride.( GPS based) The rates also includes AMC of the VFD panel of 2Hp for 5 years.

3HP control panel/VFD panel shall be fullyautomatic with button operatrd for motor on solar and gride.( GPS based) The rates also includes AMC of the VFD panel of 3 Hp for 5 years.

Dismentalling of transformer and shifting it to the work shop, extraction of damaged/ burnt ciol transformer and repair/ rewinding of the burnt coil by providing and fitting of following spares.Copper winding wire 2) LT Bushing. 3) Ltbushing rod. 4) HT bushing rod Note:- The firm shall arrange for the vehicles for and movement of the transformer from site to workshop and visa visa. The firm shall be quoted according to the rates inclusive all taxes for each job type transformer. The rate shall be quoted for shifting and re shifting of the transformer, material cost, cost of the skill labour, testing and commissioning of the transformer at site. cost of the scrap which shall be retained by the firm.Transformer three phase KVA 25KVA

63KVA

100KVA

Manual extraction of submersible Pump along with the riser piupes M.S/G.I/PPR flanged pipes of 10 feet long from the depth at which pump is installed to replace the damaged motor. The job also includes complete dismentling of MS bed, sluice valve, reflex valve. 50mm

65mm

80mm

Manual lowing of submersible Pump along with the riser piupes M.S/G.I/PPR flanged pipes of 10 feet long from the depth at which pump is installed to replace the damaged motor. The job also includes complete dismentling of MS bed, sluice valve, reflex valve. 50mm

60mm

80mm

fmishing and reinforcement.

\