Power Development And Non Renewable Energy Tender

(a) 11KV Pilfer metering cubicle for 3 phase 4 wire metering system made of MS sheet thickness not less then 2mm duly powder coat painted suitable for indoor as well as per the site requirement. The cubical shall be painted through 7-Tank process. The external dimension should be adequate, panel have two compartments upper meter compartment and lower CT/PT compartment, provided with synthetic or semi synthetic gasket firmly glued to the surface, dust weayherand vermin proof and shall comply degree of protection IP 65 both the chamber having one sided hinged door arrangements. The metering panel shall be provided with two Nos. MS channels of sized 100x50mm on the front and rear side duly welded and 4 Nos. of lifting hooks. it should be possible to take meter reading manually through CMRI and computer without opening the LV chamber door. (b) Single phase, Single core, single ratio, epoxy resin cast current transformer suitable for 11kV, copper wound primary type with rated burden 5VA and accuracy class 0.5 or better and conforming to IS2705 (Part-I & II) amended upto date. ISF shall be upto 5. the CT ratio 20/5 A. (c) 11kV/110V, 3-Phase epoxy resin cast PT with rated burden 15VA per phase and accuracy class 0.5 or better and conforming to IS: 3156 (part-I&II) amended upto date with proper colour coded identification, PTs shall be of uniform insulating and withstand separate source 23kV pf for one minute. (d) Bus-Bar detail: CT bus-bar:- 40x6mm coppe strip 8 SWG or 30 x0.6mm copper flat strip to connect PT terminal or adequate size duly insulated by the monoplast tape. (e )PVC copper wire flexible multi-strand of required size for secondary connection for CT wiring the minimum wire size shall be 4sqmm (RYB) and for PT wiring minimum wire size shall be 2.5sqmm (RYB) (f) Copper lugs preferebly ring type duly crimped for for termination of wires and tapes (g) Grounding bus minimum 40mm copper , 25cm long fixed to the unit in HV chamber, the CTs, PTs meter and 11kV Cablesheath shall be grounded to the bus through grounding wire (green) of min size 10sqmm. (h) 3ph 3 wire, HT CT/PT operated fully static Smart Tri-Vector meter Energy meter DLMS Compliant Category "C" with RS232 port for modem compatibility, 11kV/110V , Ph-Ph (3P-3W) meters for measurment of different electrical parameter including Active Energy (kWh/MWh), Apparent Energy (kVAH/MVah) etc. (make L&T, Secure, ABB) (i) Indeoendent flexible PVC pipes PVC pipes forfor CT wiring and PT wiring of appropriate size from HT copartment to meter compartment. (j) Pedestal made out of MS channel of sizes 75x40mm or angle iron of sizes 65x65x5mm, duly painted as per site requiorement for mounting of metering panel including concrete foundation whereever required including cost of nuts and bolts.

3 Core 11kV Al Cable XLPE armoured 35sqmm including cost of clamp for its fixing where ever required.

Cable termination kit suitable for 3x35sqmm XLPE Cable (indoor/outdoor).

Earthing by way of 40mm GI pipe earthing Job includes, excevation, enhancement material and main Hole Chamber (500x450x600) with frame and cover.

Transformer Fencing completed

9Mtr. Long poles ST - 410-SP33

11KV Single core185sqmm Al Armoured XLPE cable FRLS ( one spare)

Termination Kits for Cable4No of Single Covers at both ends

HDPE Pipe for HT Cable along with Clamps for cable termination on tubular Poles and road crossing

Galvized Nuts and bolts

Danger Platees with Clamps

Anti-Clambing Device with Clamps

Earth Completed by GI Spiral /rod 20mm 2.5mtr long through GI Strip

Red Oxide

Aluminium Paint

Cement bottoming 1:2:4 as per REC standards 0.5Cum/pole

11 KV Link Set

GI Channel X-arm including Clamps and Braces for DP

Installation/Commissioning/Testing ( Labour Compound)

Earth work excavation by manual means not exceeding 1m which and ramming of bottom lift upto 1including getting out evcavated earth and disposal of surpulus excavated earth as directed by site enginer

Filling available execavated earth back after cable and HDPE laying

(a) 11KV Pilfer metering cubicle for 3 phase 4 wire metering system made of MS sheet thickness not less then 2mm duly powder coat painted suitable for indoor as well as per the site requirement. The cubical shall be painted through 7-Tank process. The external dimension should be adequate, panel have two compartments upper meter compartment and lower CT/PT compartment, provided with synthetic or semi synthetic gasket firmly glued to the surface, dust weayherand vermin proof and shall comply degree of protection IP 65 both the chamber having one sided hinged door arrangements. The metering panel shall be provided with two Nos. MS channels of sized 100x50mm on the front and rear side duly welded and 4 Nos. of lifting hooks. it should be possible to take meter reading manually through CMRI and computer without opening the LV chamber door. (b) Single phase, Single core, single ratio, epoxy resin cast current transformer suitable for 11kV, copper wound primary type with rated burden 5VA and accuracy class 0.5 or better and conforming to IS2705 (Part-I & II) amended upto date. ISF shall be upto 5. the CT ratio 20/5 A. (c) 11kV/110V, 3-Phase epoxy resin cast PT with rated burden 15VA per phase and accuracy class 0.5 or better and conforming to IS: 3156 (part-I&II) amended upto date with proper colour coded identification, PTs shall be of uniform insulating and withstand separate source 23kV pf for one minute. (d) Bus-Bar detail: CT bus-bar:- 40x6mm coppe strip 8 SWG or 30 x0.6mm copper flat strip to connect PT terminal or adequate size duly insulated by the monoplast tape. (e )PVC copper wire flexible multi-strand of required size for secondary connection for CT wiring the minimum wire size shall be 4sqmm (RYB) and for PT wiring minimum wire size shall be 2.5sqmm (RYB) (f) Copper lugs preferebly ring type duly crimped for for termination of wires and tapes (g) Grounding bus minimum 40mm copper , 25cm long fixed to the unit in HV chamber, the CTs, PTs meter and 11kV Cablesheath shall be grounded to the bus through grounding wire (green) of min size 10sqmm. (h) 3ph 3 wire, HT CT/PT operated fully static Smart Tri-Vector meter Energy meter DLMS Compliant Category "C" with RS232 port for modem compatibility, 11kV/110V , Ph-Ph (3P-3W) meters for measurment of different electrical parameter including Active Energy (kWh/MWh), Apparent Energy (kVAH/MVah) etc. (make L&T, Secure, ABB) (i) Indeoendent flexible PVC pipes PVC pipes forfor CT wiring and PT wiring of appropriate size from HT copartment to meter compartment. (j) Pedestal made out of MS channel of sizes 75x40mm or angle iron of sizes 65x65x5mm, duly painted as per site requiorement for mounting of metering panel including concrete foundation whereever required including cost of nuts and bolts.

3 Core 11kV Al Cable XLPE armoured 35sqmm including cost of clamp for its fixing where ever required.

Cable termination kit suitable for 3x35sqmm XLPE Cable (indoor/outdoor).

Earthing by way of 40mm GI pipe earthing Job includes, excevation, enhancement material and main Hole Chamber (500x450x600) with frame and cover.

Transformer Fencing completed

9Mtr. Long poles ST - 410-SP33

11KV Single core185sqmm Al Armoured XLPE cable FRLS ( one spare)

Termination Kits for Cable4No of Single Covers at both ends

HDPE Pipe for HT Cable along with Clamps for cable termination on tubular Poles and road crossing

Galvized Nuts and bolts

Danger Platees with Clamps

Anti-Clambing Device with Clamps

Earth Completed by GI Spiral /rod 20mm 2.5mtr long through GI Strip

Red Oxide

Aluminium Paint

Cement bottoming 1:2:4 as per REC standards 0.5Cum/pole

11 KV Link Set

GI Channel X-arm including Clamps and Braces for DP

Dismantling of existing HT AB Cable