Military Engineer Services Tender

Surface execvation n.exc 30 cm deep and everaging 15 cm deep and getting out in hard and dense soil.

M&L for preparation of new steel surfaces of any description over 10cm in width or girth and applying two coats of synthetic enamel paint (1st quality) over one coat of red oxide primer complete all as specified and directed.

M&L preparation of new brick, stone, concrete, asbestos cement or plaster surfaces over 10 cm width/grith and applying two coat of synthetic enamel painting to over a coat of priming paints plaster coat including filling with filler where required complete all as specified and directed.

M&L for rendering 15mm thick in CM(1:6) on fair faces of brick work or concrete surfaces finished even and smooth (without using extra lime or cement)

M&L for Pre-cast cement concrete block Using (PCC 1:3:6 type C1) masonry with solid blocks, exc. 10 cm in width and setting in CM (1:4),complete all as specified

PROVN OF INTERLOCKING TILES AT OR LINE, MESS, GUEST ROOM AND SIGCEN WASHROOM OF 402 (I) ARTY BDE SIG COY AT NURLA MIL STN UNDER AGE (I) NIMU

M&L for 25mm thick sand filling (crushed sand) under floors on in foundation including watering and consolidation complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) in as in sub base of floor/paving.

Removing excavated material n.exc 50m and depositing where directed at a level not exc 1.50m above the starting point in soft soil complete as specified and as directed.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete all as specified and directed.

Manufacturing, supplying and fixing retro reflective Mandatory/ Regulatory sign boards made of stainless steel sheet 0.50mm thick sheet of 2100 x 1500mm with frame of mild steel square bar of size 20x20x2mm with supporting legs of length of 3750 mm of mild steel square bar of size 40x40x2mm, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter/message (bi-lingual), symbols and borders etc. with retro reflective letters of size not less than 100mm high etc. complete all as specified and directed by Engineer-in-charge.

S&F for Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws as specified

CONSTRUCTION OF CAGED DISPOSAL PIT AT SHMS UNDER AGE (I) NIUM

Rolling and consolidating formation surfacesin cutting using hand rohhern exc 0.2 tonne & n.exc 0.5 tonne complete all as specified.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm.

Manufacturing, supplying and fixing retro reflective Mandatory/ Regulatory multidirectional arrow board made of stainless steel sheet 0.50mm thick sof size 400 x 100mm in arrow shape, 04 Nos of arrow fixed supporting legs of length of 1350 mm of stainless steel square bar of size 20x20x2mm, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter/message (bi-lingual), symbols and borders etc. with retro reflective letters of size not less than 50mm high etc. complete all as specified and directed by Engineer-in-charge.

PROVN OF SIGN POST ALONG THE EXISTING TRACK AND LIVING AREA OF 72 ARTY BDE CAMP UNDER AGE (I) NIMU

S&F for Rolled mild steel in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat section) including distance pieces, cleats etc. conforming to FE-410W (Gde-E250)quality -B

M&L for 40mm thick Cement concrete type B-1,1:2:4 (20mm graded aggregate) as in flooring

Removing excavated soil n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point

M&L for Machine pressed precast conctete interlocking paver block 80mm thick any shape and size with grey cement and pigment confirming to IS 15658-2006 of 80mm thick M-40 Grade complete all as specified and directed.

Manufacturing, supplying and fixing retro reflective Mandatory/ Regulatory sign boards made of stainless steel sheet 0.50mm thick sheet of 2400 x 2400mm with frame of mild steel square bar of size 20x20x2mm with supporting legs of length of 4250 mm of mild steel square bar of size 40x40x2mm, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter/message (bi-lingual), symbols and borders etc. all mild steel members to be painted in multi colours with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of red oxide primer with retro reflective letters of size not less than 100mm high etc. complete all as specified and directed by Engineer-in-charge.

M&L 75mm thick Cement concrete type E-2, 1:5:10 (using 40mm graded aggregate) as in fdn and subbase to received top payer.

M&L for Cement concrete 1:5:10 type E2 (40mm graded agg) in foundations,filling and mass concrete

M&L for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete Fe-290 (Gde E-165)

Manufacturing, supplying and fixing retro reflective Mandatory/ Regulatory sign boards made of stainless steel sheet 0.50mm thick sheet of 1200 x 900mm with frame of mild steel square bar of size 20x20x2mm with supporting legs of length of 3750 mm of mild steel square bar of size 40x40x2mm, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter/message (bi-lingual), symbols and borders etc. with retro reflective letters of size not less than 100mm high etc. all mild steel members to be painted in multi colours with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of red oxide primer complete all as specified and directed by Engineer-in-charge.

S&F for Rolled mild steel in joist, channel, angle, or tee sections, fixed independently, without conncecting plates, etc. (cut to ordinary length ie. Within 20mm of the length indicated) conforming FE-410W (Gde-E250)quality -B