Military Engineer Services Tender

Removing surplus excavated material from site not exceeding 50 mtrs from starting point and depositing where directed at level not exceeding 1.5 mtr above the starting point.

Sand cushioning for cables with hight of cushioning as 8 cm below the cable and 15 cm above the cable incl punning upto 5cm all as specified and directed . Note: Punned quantuty of sand depth 18 cm shall only be measured

Supplying and laying un-reinforced precast concrete cable cover, class LV, Type-1, flat, size 250mm x 150mm x 40mm complete all as specified and directed

Taking down old unservieable LT ug cable any size.

Supply and fixing under ground XLPE insulated armoured heavy duty electric cable with aluminium conductor cable 1100 volts grade laid in trenches / passing through GI pipe / on pole / on wall of size 10 sq mm4 core complete all as specified .

Supply and fixing under ground XLPE insulated armoured heavy duty electric cable with aluminium conductor cable 1100 volts grade laid in trenches / passing through GI pipe / on pole / on wall of size 06 sq mm 2core complete all as specified .

Supply and fixing under ground XLPE insulated armoured heavy duty electric cable with aluminium conductor cable 1100 volts grade laid in trenches / passing through GI pipe / on pole / on wall of size 50 sq mm 3.5 core complete all as specified .

Supply and fixing under ground XLPE insulated armoured heavy duty electric cable with aluminium conductor cable 1100 volts grade laid in trenches / passing through GI pipe / on pole / on wall of size 70 sq mm 3.5 core complete all as specified .

Supply and fixing G I tubing 40 mm dia light grade galvanised with all fittting and fixed fix on wall ceiling or laid in floors complete all as specified and direceted at site .( for cable protection )

Taking down old Unserviceable security light fitting/flood light fitting any size complete all as specified and directed .

S&F in replace LED building security light fitting 35 watts made of pressure diecast aluminium housing with acrylic cover as diffuser with IP65 and IK -07 protection , THD<10%, lumen output >= 110 lumen per watts with integrated lectronic driver incl copper connecting wire three core of suitable size upto connctor of ceiling rose complete incl taking down of old CFL/bulb fittings all as specified and directed.

S&F LED security light fitting 60 watts made of pressure diecast aluminium housing with acrylic cover as diffuser with IP65 and IK -07 protection , THD<10%, lumen output >= 110 lumen per watts with integrated lectronic driver incl copper connecting wire three core of suitable size upto connctor of ceiling rose complete mounting on LT pole 9 Mtr incl taking down of old CFL/bulb fittings all as specified and directed.

S&F in replacement LED flood light 100 watt 230 volts AC outdoor type with thermal management in multiple optics and equiped with IP66 protection,with impact and corrosion resistant complete with driver and lamp and making necessary connections complete all as speciified and directed.

S&F in replacement post top lantern type 40 watt 230 volts AC outdoor type with decorative post top for 360 degree indirect light IP 65 protection with impact and corrosion resistant complete with driver and lamp complete with necessary connections complete all as speciified and directed.

M&L for FRP Junction Box fixed with hinge of size not less than 200x150x100cm , with closing arrangement incl 10 Amps three pase and Neutral aluminium bus bar , internally wired nut bolts with suitable size of copper conductor and incl one No MCB SP 6 Amps mounted on din rail, complete all as specified and directed by Engr-in-Charge. Make Syntex /Hensel/ National

M&L for Hot pressed Moduled SMC Junction Box Double Door fixed with hinge of size 200x150x100 mm , with closing arrangement with 10 Amps three pase and Neutral aluminium bus bar and incl one No MCB SP 6 Amps mounted on din rail, complete all as specified and directed by Engr-in-Charge. Make : Syntex/National/Hensel

S&F in replacing GI mounting pipe of building security lights of size 32 mm to 40 mm size upto 1.2 mtr length bend into sizes incl mounting clamps made of MS flat saddles, nut bolt and washers all as specified and directed .

Supply and erection truely vertical position steel tubular swaged pole complete with cast iron base plate finial taper plug, bolts, nuts and screws as specified type 410 SP-31 (9.0 mtr long), complete all as specified and directed by Engr-in-Charge.

S & f in replacement PVC insulated stranded copper conductor FRLS 1.5 sqmm for connectionfrom pole junction box to connector of street light fitting complete all including taking down all as specified and directed.

Supply installing, testing and commissioning of LT Panel outdoor kiosk type double door factory made of angle iron 65mmx 65mmx 6mm on all side welded to 3.15 mm thick CRCA sheet steel for outer compartment and 2.0 mm thick for inner compartment with openable shutteron both sides ( front and rear) , having locking arrangement totally enclosed weather proof outdoor spray painted internally and externally with two coats of synthetic enamel paint over a coat of primer suitable for 440 volts, 3 phase, 4 wire, 50 Hz with Aluminium bas bar of capacity 200 Amps AC supply, electrically connected as per norms and fitted with following accessories all as specified and directed by the Engr-in Charge. (Note:- LT panel shall be mounted on PCC 1:2:4 type B-1 with 20 mm graded stone aggregate foundation block of suitable size upto 40 cm above ground level as directed. The cost of the PCC block shall be deemed to be included in the unit rate quoted for the item & width of the panel not less than 75 cm) . The panels shall be of CPRI approved Note:- Drg of panel shall got approved before execution at site. INCOMMER Incoming MCCB, 415V, 4 pole, 2500 Amps, 25 KA, Ics =100% Icu - 01 Nos Indicator Lamp-01 Set (Set of three) Voltmeter 0-500 Volt , 415V , 50 Hz ,with selector switches -01 set Ammeter 0- 500 Amps with CTs, 415V 50 Hz with selector switches -01 set OUTGOING MCCB, 415V, 4 pole, 100 Amps,25 KA -02 No MCCB 4 pole 63 Amp, 415V, 36 KA, 4 pole , 02 Nos MCB SPN 20 Amps , 230V, 50 Hz - 02 Nos

Supply installing, testing and commissioning of LT Panel outdoor kiosk type double door factory made of angle iron 65mmx 65mmx 6mm on all side welded to 3.15 mm thick CRCA sheet steel for outer compartment and 2.0 mm thick for inner compartment with openable shutteron both sides ( front and rear) , having locking arrangement totally enclosed weather proof outdoor spray painted internally and externally with two coats of synthetic enamel paint over a coat of primer suitable for 440 volts, 3 phase, 4 wire, 50 Hz with Aluminium bas bar of capacity 400 Amps AC supply, electrically connected as per norms and fitted with following accessories all as specified and directed by the Engr-in Charge. (Note:- LT panel shall be mounted on PCC 1:2:4 type B-1 with 20 mm graded stone aggregate foundation block of suitable size upto 40 cm above ground level as directed. The cost of the PCC block shall be deemed to be included in the unit rate quoted for the item & width of the panel not less than 75 cm) . The panels shall be of CPRI approved Note:- Drg of panel shall got approved before execution at site. INCOMMER Onload change over 415V, 50 Hz , 160 Amps capacity ,4 pole -01 No Incoming MCCB, 415V, 4 pole, 160 Amps, 25 KA, Ics =100% Icu - 01 Nos Indicator Lamp-01 Set (Set of three) Voltmeter 0-500 Volt , 415V , 50 Hz ,with selector switches -01 set Ammeter 0- 500 Amps with CTs, 415V 50 Hz with selector switches -01 set OUTGOING MCCB, 415V, 4 pole, 100 Amps,25 KA -01 No MCCB 4 pole 63 Amp, 415V, 36 KA, 4 pole , 02 Nos MCB SPN 40 Amps , 230V, 50 Hz - 04 Nos

Supply installing, testing and commissioning of Bus bar junction box panel outdoor kiosk type factory made of angle iron 65mmx 65mmx 6mm on all side welded to 3.15 mm thick CRCA sheet steel for outer compartment and 2.0 mm thick for inner compartment with openable shutteron both sides ( front and rear) , having locking arrangement totally enclosed weather proof outdoor spray painted internally and externally with two coats of synthetic enamel paint over a coat of primer suitable for 440 volts, 3 phase, 4 wire, 50 Hz with Aluminium bas bar of capacity 400 Amps AC supply, electrically connected as per norms and fitted with following accessories all as specified and directed by the Engr-in Charge. (Note:- Bus bar junction box shall be mounted on PCC 1:2:4 type B-1 with 20 mm graded stone aggregate foundation block of suitable size upto 40 cm above ground level as directed. The cost of the PCC block shall be deemed to be included in the unit rate quoted for the item & width of the panel not less than 75 cm) . Note:- Drg of bus bar junction box panel shall got approved before execution at site. INCOMMER/OUT GOING Incoming MCCB, 415V, 4 pole, 100 Amps, 25 KA, Ics =100% Icu -01 nos Indicator Lamp-01 Set (Set of three)

S&F in replacing LT cable junction boxes out of polycarbonate with glass fibre reinforced and size not less than 104x104x70 mm ( cable size upto 4 sqmm ) . The polycarbonate junction box shall be environmental friendly , recyclable , halogen and sylicon free, anti acid and anti corrosive with IP rating IP 67/69 in accordance with IEC 60529 weather proof UV resistant , rain water proof and temparature resistant . The gasket material of junction box shall be polyurethane and internally embedded. The junction box comprises of DIN rail and terminal for 3 phase . The degree of protection against mechanical load shall be in accordance with EN 50298-98 for IK 08 incl 5 pole terminals comany fitted and chromium plated clamps complete all as specified and directed. Cat part no :- KF 0404 B of Hensel or equivalent make in Seimens/GE/ABB

M&L for replacing 3 core copper flexible cable 1.5 sqmm PVC sheathed FRLS complete incl taking down all as specified and directed .

M&L for replacing 3 core copper flexible cable 1.5 sqmm PVC sheathed FRLS complete incl taking down all as specified and directed .( For flood light fittings)

Dismantling of ACSR conductor from steel tubular pole complete all as specified and directed.

Dismantling of insulator any type from pole comnplete all as specified and directed

Disamntling of cross azrms any size complete

Earthing complete with galvanised iron earth plate electrode 600 mm x 600 mm x 6mm thick buried directly in ground vertically to a depth not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 Mtr below normal ground level connected to and including galvanised iron strip 25X4 mm as earthing lead by means of bolts, nuts, check nuts & washers etc made of GI and connected to earthing test point all as shown in electrical plate No. 3 of SSR Part I of 2009.00 & as specified or indicated and testing on completion including exaction/earth work in any type of strata PCC ( 1:3:6 ) type C1 earthing chamber, pre cast slab 50 mm thick in cement concrete ( 1: 2 : 4 ) type B 1 ( reinforced with welded steel wire fabric (XPM) weight not less than 4 Kg / Sqm), funnel with wire mesh, I watering pipe of 20 mm bore medium grade and lugs, including galvanised iron strip 25X4 mm with GI protection pipe of 40 mm medium grade 7.5 meter long, etc complete all as specified.

M&L for earthing complete with galvanized steel earth plate electrode60cmX60cmX6mm thick buried directly in ground (earth plate not less than 2.25 mtr deep below the normal ground level) with top edge of plate not less than 1.5 mtr below the normal ground level connected to galvanized earth lead wire of 4.0 mm dia by means of nuts bolts, washers, check nuts of iron or steel including PCC pits and RCC cover in PCC 1:2:4 (type B-1) and necessary earth work in any type of soil medium grade GI watering pipe 20 mm dia with funnel and wire mesh and 15mm bore GI pipe light grade protection pipe upto test point etc including excavation and charcoal, common salt surrounded with 15cm all around the plate all as specified and shown in EP-3 of SSR Part-I. all specified and directed.

M&L plain cement concrete ratio 1:3:6 type C2 using 40 mm graded stone aggregate as in foundation filling andf mass concrete for stay/pole foundation complete all as specified and directed.

M&L plain cement concrete ratio 1:4:2 type B1 using 20 mm graded stone aggregate as in foundation filling andf mass concrete for coping including necessary form work complete all as specified and directed.

M&L plain cement concrete ratio 1:4:8 type B2 using 40 mm graded stone aggregate as in foundation filling andf mass concrete for base (bottom of pit of bed concerete) incl necessary form work complete all as specified and directed.

Dedcuct Credit for Demolished/Dismantled material Rs (-) 62092.00 (Minus) as listed in Schedule 'A' Sec-II (Credit Schedule) Note : Tenderers will not quote against this item being a tentative amount, to be considered to arrive at the 'Contract Sum'.