Military Engineer Services Tender
... More
The MES has issued a formal invitation for competitive bids for the Military Engineer Services project, for Provn Of 01 Guard Room With Attached Bathroom At Kiari And Provn Of 01 Toilet Block With Sockage Pit At Karu Under Ge 860 Ews in Leh, Ladakh, with an estimated contract value of Rs. 47,11,000. The bid opening date for this tender is 26-05-2025 and the last date for bid submission is 16-06-2025. Interested bidders for Military Engineer Services tender can download the important documents here to check the scope of work, eligibility criteria and technical requirements.
Costs
EMD
₹ 94,220Document Cost
₹ 500Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2025_MES_710455_1Tender No
8159/2025/26/E8Tender Authority
Military Engineer Services ViewPurchaser Address
-Website
http://http://mes.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
... More
Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed.
66.61
-
-
... More
Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed.
83.91
-
-
... More
M&L for reinforced cement concrete M-30 (Design Mix) using 20mm graded aggregate as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed.
23.02
-
-
... More
M&L for reinforced cement concrete M-30 (Design Mix) using 20mm graded aggregate as in Columns, pillars, piers, posts and struts complete all as specified and as directed.
5.6
-
-
... More
M&L for reinforced cement concrete M-30 (Design Mix) using 20mm graded aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed.
13.5
-
-
... More
M&L for reinforced cement concrete M-30 (Design Mix) using 20mm graded aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the likecomplete all as specified and as directed.
18.88
-
-
... More
M&L Steel sheet form work to sides of concrete foundations, footings, bases of columns raft and beams sides and soffits(if any) of foundations and plinth,beams and similar work,vertical or to batter,for rough finished flat surfaces of concrete complete all as specified and as directed.
129.60000000000002
-
-
... More
M&L Steel sheet form work to sides of pillars, posts, struts, piers, columns and stanchions, for square, rectangular or poygonal, rough finished surfaces of concrete complete all as specified and as directed.
91.7
-
-
... More
M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc rough finished surfaces of concrete complete all as specified and as directed.
164
-
-
... More
M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) etc rough finished surfaces of concrete complete all as specified and as directed.
167.06
-
-
... More
M&L for formwork Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide rough finished surfaces of concrete complete all as specified and as directed.
75
-
-
... More
M&L mild steel TMT bars 10mm dia and over cut to length, bent to shape required, including cranking bending spirally for hooping for columns hooking ends and binding with and including mild steel wire(annealed ) not less than 0.9mm dia or securing with clip complete all as specified and as directed.
4660
-
-
... More
M&L mild steel TMT bars 5mm dia and over upto and including 10mm dia as in stirrups, cut to length, bent to shape required, including cranking bending spirally for hooping for columns hooking ends and binding with and including mild steel wire(annealed ) not less than 0.9mm dia or securing with clip complete all as specified and as directed.
1362
-
-
... More
M&L PCC type B-1 1:2:4 (using 20 mm graded crushed stone aggregate) for fixing hold fast complete all as specified and as directed.
0.69
-
-
... More
S&F MS flat iron of size 25x3 mm as in hold fast conforimg to Fe 410-0 or Fe-310-0 complete all as specified and as directed.
7
-
-
... More
M&L Precast cement concrete block masonry type C1 1:3:6 (20mm graded aggregate) with solid blocks, exc. 10cm in width and, setting in cement mortar 1:6 complete all as Specified.
44.95
-
-
... More
S&F 2nd Class hard wood plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified ans as directed.
0.67
-
-
... More
M&L for 35mm 2nd class HW plain framed , panelled shutter (two panel) with lock rail and panel of 9mm B.W.P commerical ply or 12mm veneered particle board with commerical veneering on both faces. The size of rail and stile as per IS:1003 complete all as specified ans as directed.
4
-
-
... More
M&L for Glazed and skelton Windows, ventilators shutters 30 mm thick 2nd class soft wood, open rebated and prepared to receive glass, guage, etc, divided in to square with plain, chamfered or rounded mitred and rebated sash bars, any numbers, size of members of shutters as specified in SSR Part I Section 8 clause 8.20 (b) as in windows complete all as specified and as directed.
6.96
-
-
... More
S&F 100mm Butt hinges, medium weight, cold rolled mild steel and fixed complete all as specified and as directed.
52
-
-
... More
S&F 150mm Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and as directed.
40
-
-
... More
S&F 150mm Aluminium handles, cast type, anodised complete all as specified and as directed.
32
-
-
... More
S&F 300 mm aluminium alloy anodised sliding door bolt with hasp, staple complete all as specified and as directed.
7
-
-
... More
S&F 150mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and as directed.
2
-
-
... More
M&L 4 mm thick sheet glass plain ordinary quality and glazing with oil putty in square n .exc 0.50 Sqm in each pane etc complete all as specified and as directed.
4.8
-
-
... More
M&L Hardcore of guage exc 63mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface in broken stone or boulders complete all as specified and directed.
37.94
-
-
... More
M&L for Cement Concrete type D-2, 1:4:8 (using 20 mm graded crushed stone aggregate) 100mm thick as Sub base complete all as specified and directed.
136.7
-
-
... More
M&L for 40mm thick Cement Concrete type B-1, 1:2:4 (using 20 mm graded crushed stone aggregate) as in floor Sub base complete all as specified and directed.
120.69999999999999
-
-
... More
M&L for joint free non skid colour ceramic tiles 7 to 8mm thick (square/rectangular), polished, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in net slurry and pointed in white or coloured cement to match existing shed over 15mm thick screed in CM 1:6 complete all as specified and as directed.
136.7
-
-
... More
M&L for colour glazed ceramic tiles in vertical surface 450 x 350 x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over 10mm thick backing coat of CM 1:4 complete all as specified and as directed.
104.5
-
-
... More
Rendering 15mm thick in CM 1:4 , finished even and smooth surface without using extra cement complete all as specified and directed.
223.64
-
-
... More
Rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and to be finished even and smooth without using extra cement Internal Plaster complete all as specified and directed.
219.57999999999998
-
-
... More
Rendering 5mm thick in CM (1:3) finished even and smooth without using extra cement on ceilings complete all as specified and as directed.
120.69999999999999
-
-
... More
M&L for preparation of new plastered surfaces and apply two coats of cement base paint over a coat of primer chalk whiting complete all as specified and directed.
213.64000000000001
-
-
... More
M&L for preparation of new plastered surface of wall and apply two coats of OBD over a coat of primer on newly plastered surface complete all as specified and directed.
165
-
-
... More
M&L for preparation new plastered surface of ceiling and applying three coats of white wash complete all as specified and directed.
60
-
-
... More
M&L for providing two coats of synthetic enamel painting to new wood or wood based surfaces of any description, not otherwise described over 10cm width or girth over a coat of pink primer including preparation of surfaces complete all as specified and directed.
61
-
-
... More
M&L Cement concrete type C-2, 1:3:6 (using 40mm graded crushed stone aggregate) 75 mm thick as in plinth protection complete all as specified and directed.
44.36
-
-
... More
S&F vitreous china water closet (squatt pan) orrisa pattern 580x440 mm (IWC) size pan white with front or back inlet with integral 'foot rests including provn of lime concrete bedding including connections to 'flushing cistern/pipe complete all as specified and directed including 100mm CI 'P' trap etc complete all as specified and directed by Engr-in-Charge.
7
-
-
... More
S&F PVC low level white flushing cistern 10 litre capacity valve less, syphonic action type, complete with inlet, ball valve, float valve, bends, brackets, brass screws, handle including 32 mm dia PVC flush pipe of suitable length and making all connection complete all as specified and directed.
7
-
-
... More
S&F Viterous China wash hand basin white flat back size 550x400mm including CP Pillar tap 15mm, CP Waste coupling 32mm size, PVC waste pipe 32mm bore 750mm long, pair of brackets of mild steel 35x35x6mm size including cutting for and pinning in ends of brackets or erecting stand complete all as specified and directed.
2
-
-
... More
S&F Viterous China wash urinal, half stall type, white complete including providing and fixing plugs bedding urinal against wall in CM 1:2 securing urinal to plugs with and incl 60mm long brass screws, pointing around urinal back in cement incl 32mm dia PTMT waste coupling, 32mm dia PVC waste pipe and urinal spreader complete all as specified and as directed.
1
-
-
... More
S&F 600 x 450 mm beveled edged mirror of selected quality mounted on 8mm thick ply with chromium plated brass screw and cup washers complete all as specified and directed by Engr-in-charge.
2
-
-
... More
S&F Rotational moulded water tank 1000 liter polye-thylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed by Engr-in-Charge.
2
-
-
... More
S&F 20mm dia 3-layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc complete all as specified and directed by Engr-in-Charge.
40
-
-
... More
S&F 16 mm dia 3-layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc complete all as specified and directed by Engr-in-Charge.
10
-
-
... More
S&F 15 mm bore stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe and fixed complete all as specified and directed by Engr-in-Charge.
11
-
-
... More
S&F 15 mm bore chromium plated bib taps with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed by Engr-in-Charge.
7
-
-
... More
S&F 75mm dia PVC (SWR) floor trap plain with grating including jointing to waste pipe fixed in solvent cement or cement concrete 1:2:4 type B1 complete all as specified and directed by Engr-in-Charge.
11
-
-
... More
S&F 20 mm bore Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed by Engr-in-Charge.
1
-
-
... More
S&F 20 mm bore ball valves high pressure PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed complete all as specified and directed by Engr-in-Charge.
1
-
-
... More
S&F PVC connection 15mm size with PTMT nuts of length 450mm fixed complete all as specified and directed.
11
-
-
... More
S&F brass chromium plated tubular towel rail 20mm dia 600 mm long fixed complete all as specified and as directed.
2
-
-
... More
S&F Glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and as directed.
2
-
-
... More
S&F 75 mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joint laid in trenches or in floors complete all as specified and directed.
31.5
-
-
... More
S&F 75 mm dia bore PVC (SWR) bends any radius complete all as specified and directed by Engr-in-Charge.
15
-
-
... More
S&F 75 mm dia PVC (SWR) vent cowl complete all as specified and directed by Engr-in-Charge.
3
-
-
... More
S&F 110mm dia bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to floors complete all as specified and directed by Engr-in-Charge.
45
-
-
... More
S&F 110 mm dia bore PVC (SWR) bends any radius complete all as specified and directed by Engr-in-Charge.
7
-
-
... More
M&L for rendering 15mm thick in CM 1:4 using water proofing compound as per manufacturer's instruction on roof slab surfaces , finished even and smooth surface without using extra cement complete all as specified and directed by Engr-in-Charge.
Note :- Water proofing compound shall be measured and paid separately.
151.06
-
-
... More
M&L for providing APP based polymeric membrane course roof treatment in layers with following provisions :-
(i) Applying one coat of bitumen's primer polymerized primer oil based coat, evenly @ 0.3 kg/sqm as priming coat to the prepared surfaces, till the surface is properly impregnated and the solvent oil in the base primer shall be allowed to evaporated completely.
(ii) Applying APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified and directed by Engr-in-Charge.
151.06
-
-
... More
Supply only liquid water proofing compound for external plaster complete all as specified and directed.
6
-
-
... More
M&L for plywood Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one faces; 6 mm thick ( 5 Nos of ply) fixed with nails to timber frame work complete as in walls complete all as specified and directed by Engr-in-Charge.
105
-
-
... More
M&L for plywood Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one faces; 4 mm thick ( 3 Nos of ply) fixed with nails to timber frame work complete as in ceiling complete all as specified and directed by Engr-in-Charge.
62
-
-
... More
M&L second class hard wood timber scantling plain fillets square, rectangular or triangular in section, clean sawn, secured with nails or brads, sectional area exc. 6 Sq cm n.exc 13 Sq cm secured with nails or breads complete all as specified and directed by Engr-in-Charge.
410
-
-
... More
Surface Excavation in hard/dense soil n,exc 30cm deep and averaging 15cm deep and getting out complete all as specified and directed.
122
-
-
... More
M&L for cement concrete 1:3:6 100mm thick type C-2 using 40mm graded crushed stone aggregate over rammed earth as in sub base to receive floor finish etc complete all as specified.
90
-
-
... More
M&L for providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size / shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50 mm thick compacted bed of coarse sand, compacting and proper embedding/laying of Inter locking paver blocks in to the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern. finishing and sweeping extra sand complete all as specified .
90
-
-
... More
Removing Excavated soil exceeding 250M but not exceeding 500M and depositing where directed at a level not exceeding 1.5 M above the starting point complete all as specified and directed.
13.5
-
-
... More
M&L for providing cement concrete type B-1, 1:2:4 (using 20 mm graded crushed stone aggregate) as in sides of interlocking paver blocks complete all as specified and directed.
0.85
-
-
... More
Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and getting out in hard/dense soil complete all as specified and directed by Engr-in-Charge.
11
-
-
... More
M&L for RCC 1:2:4, Type B0(Nominal Mix) (Using 12.5 mm graded stone aggregate) in footing,plinth beam complete all as specified and directed by Engr-in-Charge.
3.6
-
-
... More
M&L for RCC 1:2:4, Type B0 (Nominal Mix) (Using 12.5 mm graded crushed stone aggregate) Columns, pillars, piers, posts and struts complete all as specified and directed by Engr-in-Charge.
1.5
-
-
... More
M&L for RCC 1:2:4, Type B0 (Nominal Mix) (Using 12.5 mm graded stone crushed aggregate) Columns, pillars, piers, Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed by Engr-in-Charge.
1
-
-
... More
M&L Pre-cast cement concrete block masonry type C1 1:3:6 (using 20mm graded crushed stone aggregate) with solid blocks, 10cm in thick and, setting in cement mortar 1:4 ccomplete all as specified and directed by Engr-in-Charge.
11
-
-
... More
S&F Rolled MS Roof trusses(framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming to Fe-290 Gde E-165), complete all as specified and directed.
320
-
-
... More
S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and direct by Engineer-in-Charge.
35
-
-
... More
S&F Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and direct by Engineer-in-Charge.
3
-
-
... More
S&F 30mm thick 2nd class hardwood Plain, framed, panelled door shutters(any number of panels), with panels of timber flat on both sides(feather edged), veneered particle board medium density, wood particle board with commercial face veneers, supplied and fitted to chowkats complete all as specified and directed by Engr-in-Charge.
7
-
-
... More
S&F 4mm thick figured glass, pin head type and glazing with oil putty and glazing pins in square n exc 0.5 sq. m in each pane complete all as specified and directed by Engr-in-Charge.
1.1
-
-
... More
S&F 250 mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed by Engr-in-Charge.
5
-
-
... More
M&L for two coat of synthetic enamel paint over a coat of red oxide on new steel surfaces of any description, not otherwise described over 10cm width or girth etc complete all as specified and directed by Engr-in-Charge.
15
-
-
... More
M&L for 10 mm thick rendering in CM (1:6) on fair faces of brick work or concrete surface (Internal Plaster ) finished the surface even & smooth without using extra cement, complete all as specified and directed by Engr-in-Charge.
35
-
-
... More
Supply only water proofing compound (integral) all as specified & directed.
18
-
-
... More
M&L for 25mm thick Cement concrete type B- 2, 1:2:4 (Using 20mm graded crushed stone aggregate) as in floor to recieve tile complete all as specified and directed by Engr-in-Charge.
16
-
-
... More
M&L Vitreous China Urinal, full stall type, white (excluding flushing cistern, flush pipe and waste pipe) with urinal spreader,waste coupling and brackets including fixing etc complete all as specified and directed by Engr-in-Charge.
1
-
-
... More
S&F 20mm PP-R gate valves (Brass insert), as per requirment of the site complete all as specified and directed by Engr-in-Charge.
1
-
-
... More
S&F plain flexible PVC waste pipe of 32mm dia, 800mm long complete all as specified and directed by Engr-in-Charge.
1
-
-
... More
M&L Concrete bed 1:4:8 type D-2 to drain pipes incl packing under and haunching against the sides of pipes after they are laid and tested bore of pipe in 110 mm.complete all as specified and directed by Engr in Charge.
35
-
-
... More
S&F 110mm dia bore PVC (SWR) junction single, (single T) equal or unequal complete all as specified and directed by Engr-in-Charge.
5
-
-
... More
Excavation over areas n.exc 1.5m deep and and getting out in hard/dense soil complete all as specified and directed by Engr-in-Charge.
33.8
-
-
... More
Excavation over areas exc 1.5m deep and n.exc 3.00 m deep and getting out in hard/dense soil complete all as specified and directed by Engr-in-Charge.
33.82
-
-
... More
M&L for PCC 1:3:6 type C-2 (Nominal Mix) using 40 mm graded crushed stone aggregate as in foundation filling mass concrete and similar work complete all as specified and as directed.
1.71
-
-
... More
M&L for Walling of random rubble uncoursed, well bonded, bedded and solidly hearted, built in CM 1:6 complete all as specified and directed by Engr-in-Charge.
15.4
-
-
... More
M&L for Walling of random rubble stone masonary, uncoursed, well bonded, bedded and solidly hearted, laid dry complete all as specified and directed by Engr-in-Charge.
13
-
-
... More
M&L for providing RCC type B-1 1:2:4 Nominal Mix using 20 mm graded aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed by Engr-in-Charge.
2.7
-
-
... More
M&L TMT bars 6 to 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engr-in-Charge.
25
-
-
... More
M&L for precast cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in cover slab for manhole set in CM 1:4 including necessary form work complete all as specified and directed by Engr in Charge.
0.25
-
-
... More
M&L for Plain cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregate as in coping, benching bed plates and the line including necessary form work and finishing all exposed surface of concrete as per clause 4.11.16.2(a) of SSR Part-I (2009) complete all as specified and directed by Engr-in-Charge.
0.1
-
-
... More
M&L for loose filling with broken stone aggregates of gauge 80 to 150 mm in soakage pit, soakage wells complete all as specified and directed by Engr-in-Charge.
6
-
-
... More
M&L for point wiring complete for one light point / exhaust fan point / bell point controlled by one 1-way switch/ bell push, with 1.5 Sq mm (nominal area) FRLS PVC insulated un-sheathed and stranded copper conductor cable ISI marked and PVC concealed conduit ISI marked of size 20 mm dia medium grade and PVC conduit fittings such as tees, bends, elbow, reducers with and including FRLS PVC insulated unsheathed 1.5 Sqmm copper earth wire, connecting to common earth dolly with and incl Metal flush box of suitable size for fixing modular switches / sockets etc and making good surface by wall panelling etc, complete all as directed. Note : 1. The cost of Metal flush boxes and accessories etc is deemed to be included in quoted rate. 2. In case cutting & chasing of conduit is encountered with any beam / column, the PVC casing & capping or surface conduit will be used to avoid any damage to the RCC portion. 3. No cutting & chasing shall be done on ceiling surface for laying PVC conduit for ceiling fan point wiring etc, hence the PVC casing & capping or surface conduit will be used for the same.
25
-
-
... More
Description all as per serial item No. 104.00 here-in-before but for One 3 pin socket outlet, 6 Amp on “independent board”
5
-
-
... More
Description all as per serial item No. 104.00 here-in-before but for one socket outlet 15 Amps on independent board with 2.5 Sqmm copper conductor (Multi-stranded) insulated and unsheathed electric cable 1100 volts (ISI Marked) including PVC insulated and unsheathed electric cable 1100 volts 1.5 Sqmm copper stranded conductor as continuous earth wire connected to common dolly complete all as specified and as directed by Engineer-in-Charge.
4
-
-
... More
Supply and fixing switch piano flush button single pole one way 5 Amps complete all as specified and as directed by Engineer-in-Charge.
25
-
-
... More
Supply and fixing switch, socket combination 2 in 1, 5 Amp, flush type completeall as specified and as directed by Engr-in-charge.
5
-
-
... More
Supply and fixing switch socket combination multi purpose 2 in 1, 3 pin 5A/16A, 5 in 1 flush type complete all as specified and as directed by Engr-in-charge.
4
-
-
... More
Supply and fixing angular lamp holder, PVC/Polycaronate type with back plate suitable for 9 watt LED bulb for batten fittings complete all as specified and directed by the Engineer-in-Charge.
2
-
-
... More
Supply and fixing LED 9 Watt complete all as specified and as directed by Engineer-in-Charge.
2
-
-
... More
Supply and fixing ceiling rose, surface bakelite, 65 x 50 mm, three terminals complete all specified and as directed by the Engineer-in-Charge.
12
-
-
... More
Supply and fixing LED lights fitting 1x 20W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling
rose complete all as specified and as directed by Engineer-in-Charge.
16
-
-
... More
Supply and fixing sheet Metal enclosure singlr shutter type for DB’s 240 Volts Single Pole and Neutral 8 way with 200 Amps rated bus bar complete including wooden board of required size duly painted with matching colour paint all as specified and as directed by the Engr-in-charge.
1
-
-
... More
Supply and fixing MCB single pole and neutral 40 to 63 Amps , 240 volt, 10 KA, complete all as specified and as directed by the Engineer-in-Charge.
2
-
-
... More
Supply and fixing MCB single pole 6 to 32 Amps, 240 volts, 10 KA complete all as specified and as directed by the Engineer-in-Charge.
8
-
-
... More
Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metres below normal ground level, connecting to the Galvanized iron earth wire 4.0 mm dia by means of bolts, nuts , check nuts and washers of galvanized iron and steel earth wire protected by provision of GI light grade pipe 15 mm bore including provision of concrete pit made from PCC ( 1:2:4) type B-1 (using 20 mm graded stone aggregate) with 40mm thick cover of RCC 1:2:4 reinforced with XPM (Weight not less than 4 Kg/Sqm) and frame of angle iron 40 x 40 x 6 mm and handle of 6 mm dia MS bar made to shape, GI light grade 20 mm bore pipe for watering perforated at bottom, 1.50 metre long placed on top edge of earth plate, common salt & charcoal filling, with fixing arrangement , funnel, wire mesh and earth work in hard/dense soil , returning filling in and removal of surplus soil to a distance not exceeding 50 metres, all as per electrical plate No 5 of SSR 2009 Part-I and connecting to CBDB’s as specified or indicated including testing on completion .
2
-
-
... More
S&F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed by Engineer-in-Charge.
4
-
-
... More
Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm complete all as specified and as directed by Engineer-in-Charge.
3
-
-
... More
S&F Switch piano type, single pole, one way, 15 amps, 230 volts, complete all as specified and directed.
2
-
-
... More
S&F Socket, 6 pin, 5/15 Amp, multipurpose shutter type, 230 volts, complete all as specified and directed.
1
-
-
... More
S&F Ceiling rose, two to three terminals, bakelite body, 230 volts, complete all as specified and directed.
5
-
-
... More
S&F DB, double Door, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, SPN 4 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof, suitable for incorporation of MCB’s and isolators etc and making all necessary connections, duly flush of wall surface, complete all as specified and directed.
1
-
-
... More
Supply and laying XLPE insulated, armoured, heavy duty electric cable, with stranded aluminum conductor 1100 V grade nominal cross sectional area 10 Sqmm, 2 core laid in trenches, ducts, drawn through pipes across the road/path/along poles/wall/floors/equipment etc including jointing and testing complete all as specified and directed by the Engr-in-Charge.
100
-
-
... More
Excavation in trenches not exceeding 1.5m and not exceeding 1.5m in depth for laying of electric cable and getting out in hard and dense soil, complete all as specified and as directed by the Engr-in-Charge.
42.44
-
-
... More
Material and labour for un-reinforced pre-cast concrete cable covers, class LV type-1, flat size 250mm x 150mm x 40mm thick complete all as specified and directed by Engr-in-Charge.
880
-
-
... More
M&L for sand cushioning with layer of sand 8cm thick before laying of cable and 15cm after laying, streching & testing of cable in trenches complete all as specified and directed by Engr-in-Charge. Note :- Only punned thickness i.e 18cm shall be measured and paid.
10.6
-
-
... More
Supply and laying XLPE insulated, armoured, heavy duty electric cable, with stranded aluminum conductor 1100 V grade nominal cross sectional area 16 Sqmm, 2 core laid in trenches, ducts, drawn through pipes across the road/path/along poles/wall/floors/equipment etc including jointing and testing complete all as specified and directed by the Engr-in-Charge.
40
-
-
... More
Supplying & Laying, connecting and testing GI pipe 25 mm bore medium grade including necessary fittings in trenches complete all as specified and directed by Engineer-in-charge.
42
-
-
... More
Supply and fix Gun Metal Gate Valve 25 mm dia with iron wheel head, and all as directed by Engineer - in-Charge.
1
-
-
... More
M&L for Cutting and tapping in 25 mm water mains ( in position) for branch connections complete all as specified and as directed by Engineer-in-Charge.
1
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements
Past BiddersThis list is curated from the bidders of the similar tenders in the past
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%