WAPCOS Limited Tender

2.26.1 : Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.All kinds of soil

2.7.1 : Earth work in excavation by mechanical means (Hydraulic excavator )/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.Ordinary rock

od48631/2022_2023 : Boring, providing and installation bored cast-in-situ reinforced cement concrete piles<br>of grade M-30 of specified diameter and length below pile cap, to carry a safe working load not less than<br>specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution<br>and temporary casing of appropriate length for setting out and removal of same and the length of the pile to<br>be embedded in the pile cap etc. by Crawler mounted, telescopic boom hydraulic pilling Rig all complete,<br>including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured<br>up to bottom of pile cap). Note: Truck Mounted rotary/TMR/Tube well boring machine shall not be<br>used.<br>700 mm dia piles<br>Details of cost for 15 m length of pile<br>MATERIAL:<br>Concrete 3.14/4x0.75²x15 =6.62cum

od48632/2022_2023 : :Boring, providing and installation bored cast-in-situ reinforced cement concrete piles<br>of grade M-30 of specified diameter and length below pile cap, to carry a safe working load not less than<br>specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution<br>and temporary casing of appropriate length for setting out and removal of same and the length of the pile to<br>be embedded in the pile cap etc. by Crawler mounted, telescopic boom hydraulic pilling Rig all complete,<br>including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured<br>up to bottom of pile cap). Note: Truck Mounted rotary/TMR/Tube well boring machine shall not be<br>used.<br>800 mm dia piles

od48633/2022_2023 : Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of grade M-30 of specified diameter and length below pile cap, to carry a safe working load not less than<br>specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution<br>and temporary casing of appropriate length for setting out and removal of same and the length of the pile to<br>be embedded in the pile cap etc. by Crawler mounted, telescopic boom hydraulic pilling Rig all complete,<br>including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured<br>up to bottom of pile cap). Note: Truck Mounted rotary/TMR/Tube well boring machine shall not be<br>used.<br>900 mm dia piles<br>Details of cost for 10 m length of pile<br>MATERIAL:<br>Concrete 3.14/4x1.00x10 = 7.85 cum

20.6.2.1 : Vertical load testing of piles in accordance with IS 2911( Part IV) including installation of loading platform and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of engineer -in-Charge.Single pile above 50 tonne and upto 100 tonne capacityInitial test

20.6.2.2 : Vertical load testing of piles in accordance with IS 2911( Part IV) including installation of loading platform and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of engineer -in-Charge.Single pile above 50 tonne and upto 100 tonne capacityRoutine test

2.25 : Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

od35730/2022_2023 : Extra for additional bed upto 1Km or initial lead of 50M for disposing of surplus excavated earth as per the direction of the engineer in charge

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

5.33.1 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work upto plinth level

5.34.1 : Extra for providing richer mixes at all floor levels. Note:- Excess/less cement over the specified cement content used is payable/ recoverable separately.Providing M-30 grade concrete instead of M-25 grade BMC/RMC. (Note:- Cement content considered in M-30 is @ 340 kg/cum).

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.5 : Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.9.2 : Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

4.11 : Providing and laying damp-proof course 50 mm thick with cement concrete 1:2:4(1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

od51749/2022_2023 : Solid block masonry using pre cast Fly ash solid blocks (Factory made with a<br>minimum fly ash composition of 40%) of size 40x20x20cm or nearest available size confirming to IS 2185<br>Part I of 1979 for super structure above floor two level up to floor V level thickness 20cm and above in: CM<br>1:6 ( 1 cement :6 coarse sand) etc complete

od35739/2022_2023 : Supplying and filling with quarry dust under slabs, including watering,<br>ramming consolidating and<br>dressing complete.

Super structure

5.33.2 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work above plinth level upto floor V level

5.34.1 : Extra for providing richer mixes at all floor levels. Note:- Excess/less cement over the specified cement content used is payable/ recoverable separately.Providing M-30 grade concrete instead of M-25 grade BMC/RMC. (Note:- Cement content considered in M-30 is @ 340 kg/cum).

5.9.3 : Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.9.19 : Centering and shuttering including strutting, etc. and removal of form for:Weather shade, Chajjas, corbels etc., including edges

5.9.2 : Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.5 : Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.9.6 : Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

5.9.7 : Centering and shuttering including strutting, etc. and removal of form for:Stairs, (excluding landings ) except spiral - staircases)

5.22A.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo - Mechanically Treated bars of grade Fe-500D or more

od48683/2022_2023 : Providing expansion joints on the roof by synthetic rubber water bar embedded in the<br>expansion gap and insulating the surface with a coat of bitumen after forming a small hump profile over the<br>joint by using 1:3 braced RCC cement plaster, providing flat first layer of bitumen felt of crown piece seal<br>over the lap joints fixing with a layer of bitumen felt extending over the hump crown and finishing along the<br>cemented surface of the two slabs, so as to continuously take any finishing work etc. complete to<br>specification.

od48684/2022_2023 : Providing 15cm wide strips bitumen based mineral fibre pad conforming to IS 1838, so<br>as to totally seal any gaps between the two joints/expansion gap before finishing plastering work and<br>flooring etc. complete to specification

od36154/2022_2023 : Solid block masonry using pre cast Fly ash solid blocks (Factory made) of size 40x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement: 6 coarse sand) etc complete.

od43516/2022_2023 : Solid block masonry using pre cast Fly ash solid blocks (Factory made with a<br>minimum fly ash composition of 40%) of size 40x20x20cm or nearest available size confirming to IS 2185<br>Part I of 1979 for super structure above floor two level up to floor V level thickness 20cm and above in: CM<br>1:6 ( 1 cement :6 coarse sand) etc complete

od36155/2022_2023 : Solid block masonry using pre cast Fly ash solid blocks (Factory made) of size 40x20x10 cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level for 10 cm thick wall in : CM 1:6 ( 1 cement : 6 coarse sand) including cost of scaffolding complete

od43523/2022_2023 : Solid block masonry using pre cast Fly ash solid blocks (Factory made with a<br>minimum fly ash composition of 40%) of size 40x20x10 cm or nearest available size confirming to IS 2185<br>part I of 1979 for super structure from floor two level to floor five level for 10 cm thick wall in : CM 1:6 ( 1<br>cement : 6 coarse sand) including cost of scaffolding complete

6.47 : Providing and laying autoclaved aerated cement blocks masonry with 150mm/ 230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).

Finishing works

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

13.2.1 : 15 mm cement plaster on the rough side of single or half brick wall of mix:1:4 (1 cement :4 fine sand)

13.22 : Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof.

5.23 : Smooth finishing of the exposed surface of RCC work with 6mm thick cement mortar 1:3 ( cement : 3 fine sand).

13.7.2 : 12 mm cement plaster finished with a floating coat of neat cement of mix:1:4 ( 1 cement : 4 fine sand)

od38203/2024_2025 : Brick jelly concrete in cement concrete 1:3:6 using 40mm broken bricks including cost, labour charges etc complete<br>

4.2.5 : Providing and laying cement concrete in retaining walls, return walls, walls ( any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts,buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor, etc. up to floor five level, excluding the cost of centering, shuttering and finishing:1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 20 mm nominal size)

13.80 : Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

13.43.1 : Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

od41844/2022_2023 : Providing two coats of wall painting with premium acrylic emulsion paint of interior<br>grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and<br>manufacture, including applying additional coats wherever required to achieve even shade and colour

od41845/2022_2023 : Finishing walls with Acrylic Smooth exterior paint having VOC (Volatile Organic<br>Compound ) content less than 50 grams/ litre of required shade:New work (Two or more coat applied @ 1.67<br>ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

13.44.1 : Finishing walls with water proofing cement paint of required shade:New work (Two or more coats applied @ 3.84 kg/10 sqm)

12.63 : Providing and applying two coats of High Albedo paint having minimum Solar Reflective Index (SRI) 108 (with solar reflectance & thermal emittnce tested as per ASTM) C 1549 and ASTM C 1371 respectively), VOC less than 10 cc/gm. The coating thickness and the methodology of application shall strictly as per manufacture's specifications and as approved by engineer in charge. Surface preparation includes cleaning with metal wire brush to remove all dust, fungus etc., washing with water all complete. The contractor shall give guarantee for the performance of SRI and also the durability of coating, all complete as per direction of Engineer - in- charge.

9.48.2 : Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings/ wooden frames with rawl plugs screws etc

od43955/2022_2023 : Painting with synthetic enamel paint having VOC (Volatile Organic Compound) content<br>less than 150 grams/ litre, of approved brand and manufacture, including applying additional coats wherever<br>required to achieve even shade and colour.

10.28 : Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)

11.20.3 : Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand).Dark shade pigment using ordinary cement

11.41.2 : Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm.

11.46.2 : Providing and laying Vitrified tiles indifferent sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 600x600 mm

od41928/2022_2023 : Providing and laying anti skid vitrified tiles of size 600x600 mm or more (thickness to<br>be specified by the manufacturer) of Ist quality conforming to IS: 15622 of approved make in all colours,<br>shades, except white, Ivory, Grey Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4<br>Coarse sand) including grouting the joints with epoxy grouting and matching pigments etc., complete.

od42000/2022_2023 : Providing and fixing I st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer -in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

8.2.2.1 : Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite of any colour and shadeArea of slab upto 0.50 sqm

8.2.2.2 : Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Area of slab over 0.50 sqm

8.9.1.2 : Stone tile (polished) work for wall lining over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and cement slurry @ 3.3 kg/sqm including pointing in white cement complete.Granite of any colour and shade

od44607/2022_2023 : Providing and laying FRP lining water proofing treatment in sunken portion of WC's<br>bathroom etc. as per specification. The application shall be done only after cleaning of surface, there after<br>applying powder with resin, compound, then laying of FRP lining (fibre glass lamination) by applying resin<br>with blue pigment etc. as per manufactures specification. Application of first coat resin with chalk powder on<br>the corner, uneven surface and undulation and laying the o Fibre glass lamination with resin and blue<br>pigment, o Surfase mat lamination with resin. The second coat application shall be done with applying resin with Paraffin wax, chalk powder and blue pigment etc. complete. The rate includes preparation of surface,<br>pressure grouting over slab & side wall, treatment and sealing of all joints, corners, junctions of pipes and<br>masonry with polymer mixed slurry and testing of applied area complete.<br>

od44608/2022_2023 : :Providing and laying FRP lining water proofing treatment in terrace & sunshades as<br>per specification. The application shall be done only after cleaning of surface, there after applying powder<br>with resin, compound, then laying of FRP lining (fibre glass lamination) by applying resin with blue pigment<br>etc. as per manufactures specification. Application of first coat resin with chalk powder on the corner,<br>uneven surface and undulation and laying the o Fibre glass lamination with resin and blue pigment, o<br>Surfase mat lamination with resin. The second coat application shall be done with applying resin with<br>Paraffin wax, chalk powder and blue pigment etc. complete. The rate includes preparation of surface,pressure grouting over slab & side wall, treatment and sealing of all joints, corners, junctions of pipes and<br>masonry with polymer mixed slurry and testing of applied area complete.<br>

od44609/2022_2023 : Providing and laying FRP lining water proofing treatment in shear walls as per<br>specification. The application shall be done only after cleaning of surface, there after applying powder with<br>resin, compound, then laying of FRP lining (fiber glass lamination) by applying resin with blue pigment etc.as per manufactures specification. Application of first coat resin with chalk powder on the corner, uneven<br>surface and undulation and laying the o Fiber glass lamination with resin and blue pigment, o Surface mat<br>lamination with resin. The second coat application shall be done with applying resin with Paraffin wax, chalk<br>powder and blue pigment etc. complete. The rate includes preparation of surface, pressure grouting over<br>slab & side wall, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer<br>mixed slurry and testing of applied area complete.

od46194/2022_2023 : Providing and laying FRP lining water proofing treatment in water tank as per<br>specification. The application shall be done only after cleaning of surface, there after applying powder with<br>resin, compound, then laying of FRP lining (fibre glass lamination) by applying resin with blue pigment etc.<br>as per manufactures specification. Application of first coat resin with chalk powder on the corner, uneven<br>surface and undulation and laying the o Fibre glass lamination with resin and blue pigment, o Surfase mat<br>lamination with resin. The second coat application shall be done with applying resin with Paraffin wax, chalk<br>powder and blue pigment etc. complete. The rate includes preparation of surface, pressure grouting over<br>slab & side wall, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer<br>mixed slurry and testing of applied area complete

21.1.1.2 : Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

21.1.2.2 : For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron)

9.1.2 : Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).Sal wood

9.21.1 : Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non- decorative Type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

9.53 : Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

9.74.1 : Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete:250x10 mm

9.76 : Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

9.82 : Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

od59792/2022_2023 : Supplying and fixing Non-Hermetically Sealed Manual Double Leaf Swing Door of<br>Antimicrobial HPL finish Nik229 swing door of 44 mm thick with 45±2 kg/m3 density PUF insulated. Anodized<br>aluminum alloy door profile. Wall frame 80 mm x 60 mm, 2.5 mm thick Al 6063 anodized with 2mm GI<br>reinforced. Including providing double glazed vision panel with 4 mm clear glass (300 mm x 300 mm x 44 mm<br>or above size as directed by Architect), euro norm cylinder lock with outside key and inside emergency<br>release, both side SS D-handle , SS ball bearing hinges , door closure push and hold for active leaf ,<br>providing concealed drp seal, rubber gasket for air tightness, concealed/open Stainless steel Tower bolts of<br>250 & 150mm, Stainless steel door stopper etc. complete in all respect as directed by Engineer in charge. No<br>Organic material (No Decay and No Contamination) for all main doors.

od60239/2022_2023 : Supplying and fixing non Hermetically sealed single leaf manual sliding door of<br>Antimicrobial HPL Seam Less finish, Nik229 with lever handle both side for manual opening, Door profile<br>made of Aluminium Alloy Grade 6063 Temper T6.Natural Anodised 20 m as per EN ISO 2360. Component<br>Polyurethane Rigid CFC Free, Blowing Agent: Water. Dimensional stability at +100°C & -25°C (2%max) as per<br>DIN53431. Density 45Kg/M3 with max deviation of 2kg/m3 as per DIN53420. Condensation resistance at 38°C<br>and 88RH > Max variation 2% in Weight and volume. Lever Handle Solid AISI 304 Grade Stainless Steel,Rubber spring system. Roller Material PA6G 210 (Self-lubricating) PA Bearings 2X per roller. Rail Aluminium<br>Alloy, Grade 6063, Temper T6. Photo cell fitted across the door opening inside the wall frame. Double glazed<br>IG unit with 5 mm tempered glass of size 300 mm x 300 mm x 60mm, flush finished."

od59796/2022_2023 : Providing and fixing 30mm thick factory made single extruded WPC {Wood Polymer<br>Composite) solid decorative type panelled/flush door shutter of required size comprising of virgin polymer of<br>K value 58-60 {Suspension Grade), calcium carbonate and natural fibers {wood powder/ rice husk/wheat<br>husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650<br>kg/cum and screw withdrawa l strength of 1800 N (Face) & 900 N {Edge), minimum compressive strength<br>50N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with<br>property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC<br>foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter<br>and fix ing with stainless steel butt hinges of required size with necessary full body threaded star headed<br>counter sunk 5.5 screws, all as per direction of Engineer-In- Charge. {Note: stainless steel butt hinges and<br>necessary 5.5 screws shall be paid separately) for toilet door.<br>

od59797/2022_2023 : Providing and fixing factory made single extruded WPC (Wood Polymer Composite)<br>solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K<br>value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk)<br>and non toxic addit ives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after<br>applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum<br>frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of<br>Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed<br>in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of<br>Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately

od62002/2022_2023 : Providing and fixing Aluminum composite panel 4mm thick for aluminum doors<br>with<br>necessary screws, beedings etc complete

od74323/2022_2023 : Providing and fixing in position CNC wall panelling on exterior wall .The wall has to be finished as per architectural specification. Cost including all labour charges for making ,loading unloading in site. and fixing at proper places with scaffoldings if necessary.

12.52.1 : Providing and fixing tiled false ceiling of approved materials of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams per sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x 1.6 mm fixed to ceiling with 12.5mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85x 30x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer -in-charge.GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending

12.52.2 : Providing and fixing tiled false ceiling of approved materials of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams per sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x 1.6 mm fixed to ceiling with 12.5mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85x 30x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer -in-charge.GI Metal Ceiling Lay in perforated Tegular global white color tiles of size 595x595 mm and 0.5mm thick with 8 mm drop; made of GI sheet having glavanizing of 100 gms/ sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient) of 0.5, electro statically polyster powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fiber acoustical fleece.

26.26.1 : Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Non combustible as per BS 476 (part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 15x32 mm of length 3000 mm, cross - T of size 15x32 mm of length 1200 mm and secondary intermediate cross-T of size 15x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge.With semi perforated 12 mm thick micro tegular edged GRG false ceiling tiles.

26.26.2 : Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Non combustible as per BS 476 (part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 15x32 mm of length 3000 mm, cross - T of size 15x32 mm of length 1200 mm and secondary intermediate cross-T of size 15x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge.With fully perforated 12 mm thick micro tegular edged or 10 mm thick square edged GRG false ceiling tiles.

od75150/2022_2023 : Providing and fixing false ceiling 250 mm x 6 mm thick multi chamber hollow PVC panel .The support from ceiling is to be provided using 25 mm x 25 mm size aluminum square tube pipe at a distance of 2 ft (Framing work) with complete fitting etc complete as per specification.<br>

9.105.3 : Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with Zinc coating of 120 gms/ (both side inclusive), consisting of floor and ceiling channel 50 mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete.66 mm overall thickness Partition with 8 mm thick double skin Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process with Compressive Strength 225 kg/sq cm, Bending Strength 100 kg/sq cm

21.13 : Providing and fixing 100 mm brass locks ( best make of approved quality ) for aluminium doors including necessary cutting and making good etc. complete

14.34 : Providing and fixing 150 mm bright finished floor brass door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete

9.71.2 : Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete:100x60x2.50 mm

9.74.3 : Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete:150x10 mm

21.16.2 : Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. complete as per direction of Engineer-in-Charge.Powder coated minimum thickness 50 micron aluminium

10.6.1 : Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.80x1.25 mm M.S. laths with 1.25 mm thick top cover

10.7 : Providing and fixing ball bearing for rolling shutters.

10.8.1 : Extra for providing mechanical device chain and crank operation for operating rolling shuttersExceeding 10.00 sqm and upto 16.80 sqm in the area

10.9 : Extra for providing grilled rolling shutters manufactured out of 8 mm dia M.S. bar instead of laths as per design approved by Engineer -in-Charges, (area of grill to be measured).

od45467/2022_2023 : Supply of vision panel in fire rated doors of 200 mm x 500 mm size made out<br>of<br>minimum 5 mm thick clear fire rated glass (imported) for 120 minutes fire rating of fully transparent<br>in<br>fire/non-fire conditions having minimum 93% transparency, in accordance with IS : 3614 Part -II and<br>BS : 476<br>Part 20& 22 , for 120 min. fire rating for stability and integrity and insulation criteria

od45468/2022_2023 : Providing and fixing concealed fire rated 120 minutes RT door closer along<br>with<br>necessary SS screws, bolts, nuts, washers etc. as per approved samples complete as per the<br>direction of the<br>Engineer-in-charge.

od45469/2022_2023 : Providing and fixing panic bar / latch (Single point) fitted with a single body,<br>Trim<br>Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by<br>the<br>Engineer- in- charge, all complete

od45470/2022_2023 : Providing and fixing Door frame and Shutter made of 46mm thick steel fire check<br>door<br>of 120 minutes fire rating confirming to BS: 476 Part 22 and IS: 3614 Part II for stability and<br>integrity,<br>fabricated with 2 nos. 22 gauge thick galvanized steel sheet with infill of fire rated Acrylic<br>Sealant and noncombustible<br>core bonded to both faces of sheet with lock seam joints at stile edges and<br>internal<br>reinforcement at top, bottom and stile edges for Fire Rating. The door frames are manufactured<br>from 18<br>gauge thick galvanized steel sheet pressed from to single rebate profile of size 125mm x 75mm.<br>The frames<br>shall be fixed using canon/hilti anchor bolts of size 10mm dia x 100mm long. The door<br>frames and door<br>shutters are finished with powder coating paint. The cost includes providing and fixing<br>of minimum two-hour<br>fire rated stainless steel ball bearing hinges 125 mm x 75mm x 3mm. The cost<br>includes providing opening for<br>vision panel of required size in shutters (cost of glass excluded) and<br>fixing vision panels of specified size<br>with complete fire rated gasket channel & moulding beading and<br>filling the gap between moulding /beading<br>and glass with suitable sealant

od84500/2022_2023 : Providing and making laying fire brick walls (Factory made) of size of fire retardant bricks 9''x4''x3'' or nearest available size laid in mortar of high alumina cement and fine aggregate of crushed fire brick 1:2 including cost of scaffolding for superstructures.

21.18 : Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge ( Door handle, lock and stopper etc to be paid separately)

od45471/2022_2023 : Providing and fixing SS H handle of size 450mm with SS screws etc. complete as<br>per<br>direction of Engineer-in-Charge.

od45472/2022_2023 : :Providing and fixing SS lock of size suitable for glass door with SS screws<br>etc.<br>complete as per direction of Engineer-in-Charge

12.50 : Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

12.51.2 : Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05%) total coated thickness, zinc coating 120 grams per sqm as per IS:mm(+0.05%) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/self tapping screws complete:Flashings / Aprons (Upto 600 mm)

50.12.2.5 : Providing & fixing Poly carbonate multi wall plain sheet 8 mm thick as approved by the Engineer in charge and should be supplied in a single length of 12 M or as decide by the Engineer in charge. The sheets shall be fixed using self drilling/ self tapping screw of size ( 5.5x55mm) with EPDM seal complete upto any pitch in horizontal /vertical / curved surface, but excluding the cost of purlins, rafters, trusses, and including cutting to size and shapes where ever required.

10.16.1 : Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes

25.1 : Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account).

12.7.1 : Providing and fixing 15cm wide, 45 cm overall semi circular plain G.S. sheet gutter with iron brackets 40x3 mm size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete.0.80 mm thick with zinc coating not less than 275 gm/m2

25.4 : Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge.

25.2 : Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including: a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)-cumsmoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including: b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers. c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment , including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass. d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight. e) Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-in-charge. The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight structural glazing having all the performance characteristics etc. all complete as required, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineerin- Charge. Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section capping for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall be paid for separately under relevant items under this sub-head. However, for the purpose of payment, only the actual area of structural glazing (including width of grooves ) on the external face shall be measured in sqm. up to two decimal places. Note:-2. The following performance test are to be conducted on structural glazing system if area of structural glazing exceeds 2500 Sqm from the certified laboratories accreditated by NABL(National Accreditation Board for Testing and Calibration Laboratories), Department of Science & Technologies, India. Cost of testing is payable separately. The NIT approving authority will decide the necessity of testing on the basis of cost of the work, cost of the test and importance of the work. Performance Testing of Structural glazing system Tests to be conducted in the NBL Certified laboratories 1. Performance Laboratory Test for Air Leakage Test (-50pa to – 300pa) & (+50pa to +300pa) as per ASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr” 2. Static Water Penetration Test. (50pa to 1500pa) as per ASTME- 331-09 testing method for a range up to 2000 ml.” 3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01-05 testing method for a range upto 2000 ml” 4. Structural Performance Deflection and deformation by static air pressure test (1.5 times desing wind pressure without any failure) as per ASTME-330-10 testing method for a range upto 50 mm” 5. Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing method for Qualitative test” Tests to be conducted on site 6. Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto 2000ml”

od58324/2022_2023 : Providing and fixing Cubicle curtains in the wards suitable for beds laid. The rate includes all cost of cloth, curtain track, supports, hardware items, stitching charges and all labour charges including conveyance, loading unloading etc. complete in all respect. The length of curtain cloth should have 1metre more length than the channel length. The height of curtain should have 7.5feet or standard approved ht. payment shall be made only as per site measurements of works actually done. (Curtained track length only shall be measured for payment) for All multi bed areas (Recovery, ICU, General wards Palliative wards, Procedure rooms, etc)<br>

od58501/2022_2023 : Providing, fitting fixing12mm thick toughened glass partition as per design. The partiton will be supported withS.S patch panel fittings of approved barnd as, The exposed edge of the glass partition should be polished to super quality , providing fixing arrangement and making necessary holes and fittings, including cost of all labour & material etc. complete as per direction of Engineer-in-charge . <br>

od46228/2022_2023 : :Providing heavy duty FRP manhole cover and frame of size 75cmx75cm internal<br>dimension with load<br>bearing capcity of 2.5 tonne made of polyster resin , fibre glass and fillers of<br>approved quality fixing in<br>correct line and level as directed by Engineer-in-charge

21.3.1 : Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness

od49084/2024_2025 : Providing and applying application of Transparent Glass Coating to Block Heat on the indoor side of 4 mm thick plain glass to achieve Visible Light Transmission (VLT)greater than or equal to 71% and Solar Heat Gain Coefficient (SHGC) less than or equal to 0.61 for external windows only as per the direction from Engineer-in -Charge

GRIHA

od40565/2024_2025 : Supply of Green Cleaning Chemicals as per the direction of Engineer in charge (Note: Payment shall be be made as per the actual bills submitted and same shall be reimbursed)

External works

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

2.26.1 : Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.All kinds of soil

7.1.1 : Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

5.33.1 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work upto plinth level

5.33.2 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work above plinth level upto floor V level

5.34.1 : Extra for providing richer mixes at all floor levels. Note:- Excess/less cement over the specified cement content used is payable/ recoverable separately.Providing M-30 grade concrete instead of M-25 grade BMC/RMC. (Note:- Cement content considered in M-30 is @ 340 kg/cum).

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.2 : Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.3 : Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.9.5 : Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.9.7 : Centering and shuttering including strutting, etc. and removal of form for:Stairs, (excluding landings ) except spiral - staircases)

2.25 : Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

19.32.1 : Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

od62367/2022_2023 : :Solid block masonry using pre cast Fly Ash solid blocks (Factory made with a<br>minimum fly ash composition of 40%)) of size 40x20x20cm or nearest available size confirming to IS 2185<br>part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement: 6<br>coarse sand) etc complete<br>Details of cost for one cum

13.16.1 : 6 mm cement plaster of mix:1:3 ( 1 cement : 3 fine sand)

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

13.2.1 : 15 mm cement plaster on the rough side of single or half brick wall of mix:1:4 (1 cement :4 fine sand)

od41275/2022_2023 : Providing two coats of wall painting with premium acrylic emulsion paint of interior<br>grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and<br>manufacture, including applying additional coats wherever required to achieve even shade and colour

od62259/2022_2023 : <br>Finishing walls with Acrylic Smooth exterior paint having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of required shade:New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)<br>

22.6 : Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying : a) after surface preparation, first layer of slurry of cement @ 0.488 kg/ sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. laying second layer of fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/ sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. d) fourth and final layer of brick tilling with cement mortar (which will be paid for separately. For the purpose of measurement the entire treated surface will be measured)

21.1.1.2 : Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

21.1.2.2 : For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron)

21.2.2 : Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS : 12823 Grade I Type II, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer - in- Charge.Pre- laminated particle board with decorative lamination on both sides

21.3.2 : Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5.50 mm thickness

10.6.1 : Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.80x1.25 mm M.S. laths with 1.25 mm thick top cover

10.7 : Providing and fixing ball bearing for rolling shutters.

10.8.1 : Extra for providing mechanical device chain and crank operation for operating rolling shuttersExceeding 10.00 sqm and upto 16.80 sqm in the area

10.9 : Extra for providing grilled rolling shutters manufactured out of 8 mm dia M.S. bar instead of laths as per design approved by Engineer -in-Charges, (area of grill to be measured).

od41524/2022_2023 : :"Providing of good Quality Heavy Duty Wall Supported type ALUMINUM LADDER Made<br>from 10 SWG<br>Aluminum Alloy ""C"" Section size - 66 x 33 x 3.15 mm, Rung - 25.4 mm Fluted type fixing<br>correct line<br>and level as directed by Engineer-in-charge

od41539/2022_2023 : :Providing heavy duty FRP manhole cover and frame of size 75cmx75cm internal<br>dimension with load<br>bearing capcity of 2.5 tonne made of polyster resin , fibre glass and fillers of<br>approved quality fixing in<br>correct line and level as directed by Engineer-in-charge

od41540/2022_2023 : Providing and laying FRP lining water proofing treatment in water tank as per<br>specification. The application shall be done only after cleaning of surface, there after applying powder with<br>resin, compound, then laying of FRP lining (fibre glass lamination) by applying resin with blue pigment etc.<br>as per manufactures specification. Application of first coat resin with chalk powder on the corner, uneven<br>surface and undulation and laying the o Fibre glass lamination with resin and blue pigment, o Surfase mat<br>lamination with resin. The second coat application shall be done with applying resin with Paraffin wax, chalk<br>powder and blue pigment etc. complete. The rate includes preparation of surface, pressure grouting over<br>slab & side wall, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer<br>mixed slurry and testing of applied area complete

16.71 : Providing and fixing G.I. chain link fabric fencing of required width in mesh size 25x25 mm made of G.I wire of dia 3 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer - in- Charge.

od56160/2022_2023 : Providing and laying 60 mm thick factory made cement concrete interlocking paver<br>block of M - 30 grade made by block making machine with strong vibratory compaction, of approved size,<br>design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse<br>sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.

Formation of Bituminous road

3.6 : Excavation for roadwork in soil with hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting to the embankment location within all lifts and lead upto 1000m

4.2.A.1 : Construction of granular sub-base by providing graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401. br Grading-III -For lower sub base - Mix in Place Methodbr

4.12 : Providing, laying, spreading and compacting graded stone aggregate to Wet Mix Macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density.

5.1.a : Providing and applying primer coat with bitumen emulsion ( SS) on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.70 - 1.0 kg/sqm using mechanical means.

5.2.a : Providing and applying tack coat with bitumen emulsion( RS) using emulsion pressure distributor at the rate of 0.20 - 0.30 kg per sqm on the prepared bituminous surface cleaned with mechanical broom.

5.3.2.a : Providing and laying bituminous macadam with 80-100 TPH hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading premixed with bituminous binder (VG 30), transported to site, laid over a previously prepared surface with paver finisher to the required grade, level and alignment and rolled as per clauses 501.6 and 501.7 to achieve the desired compaction.br For Grading II - (19 mm nominal size)br

5.6.2.a : Providing and laying bituminous concrete with 80-100 TPH hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder( NRMB) @ 5.4 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification clause No. 507 complete in all respects Grading - II (13.2 mm Nominal Size)br

3.18 : Construction of sub-grade and earthen shoulders with approved material obtained from borrow pits with all lifts & leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table No. 300-2

8.11.1 : Painting lines, dashes, arrows etc on roads in two coats on new work with ready mixed road marking paint conforming to IS:164 on bituminous surface, including cleaning the surface of all dirt, dust and other foreign matter, demarcation at site and traffic control Over 10 cm in width

8.13 : Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads on Bituminous Surface @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.

Development of Koyilandi Taluk Hospital - Landscape works

od62052/2022_2023 : Taking pit size 0.75M x0.75M.x0.75M., fill it with earth and organic manure mixture and<br>supply and planting trees MIMUSPOS ELENGI

od62053/2022_2023 : Taking pit size 0.75M x0.75M.x0.75M., fill it with earth and organic manure mixture and<br>supply and planting trees SARACA ASOCA

od62074/2022_2023 : Taking pit size 0.3M x0.3M.x0.3M., fill it with earth and organic manure mixture and<br>supply and planting shrubs CROSSANDRA

od62075/2022_2023 : Taking pit size 1M x1M.x1M., fill it with earth and organic manure mixture and supply<br>and planting tree ALSTONIA SCHOLARIS

od62092/2022_2023 : Providing and fixing buffalo grass existing ground prepared with proper level and<br>ramming with required tools wooden (Dhurmos) and than rolling the surface with light roller make the<br>surface smoothen and even, watering with sprinkle

od62097/2022_2023 : Supply and spreading good earth for landscaping including all cost of material and<br>labour charge etc complete

Signages

od56175/2022_2023 : Providing and fixing / holding sinages, sign board made of compact aluminium panel sheet or HPL sheet of approved shade , providing 3mm vinyl pased letters with multi language and logos of approved sizes, providing side hangers fixing in position,providing centre handers using Ms rods amn chains etc. displaying scope of services, room numbers, doctors rooms, HOD rooms, floor wise facilities ,radiation sinages, mandatory notification as directed by the engineer in charge with one side lettering for fixed in wall and both sides as in projected type etc. complete to detailed pre approved plan.<br>Scope fo services in all deptmt- 120x150cm .<br>

od56645/2022_2023 : Providing and fixing / holding sinages, sign board made of compact aluminium panel sheet or HPL sheet of approved shade , providing 3mm vinyl pased letters with multi language and logos of approved sizes, providing side hangers fixing in position,providing centre handers using Ms rods amn chains etc. displaying scope of services, room numbers, doctors rooms, HOD rooms, floor wise facilities ,radiation sinages, mandatory notification as directed by the engineer in charge with one side lettering for fixed in wall and both sides as in projected type etc. complete to detailed pre approved plan.<br>Stair area 120x100cm<br>

od56193/2022_2023 : Providing and fixing / holding sinages, sign board made of compact aluminium panel sheet or HPL sheet of approved shade , providing 3mm vinyl pased letters with multi language and logos of approved sizes, providing side hangers fixing in position,providing centre handers using Ms rods amn chains etc. displaying scope of services, room numbers, doctors rooms, HOD rooms, floor wise facilities ,radiation sinages, mandatory notification as directed by the engineer in charge with one side lettering for fixed in wall and both sides as in projected type etc. complete to detailed pre approved plan.<br>Passages handing types -60x15cm -both side <br>

od56194/2022_2023 : Providing and fixing / holding sinages, sign board made of compact aluminium panel sheet or HPL sheet of approved shade , providing 3mm vinyl pased letters with multi language and logos of approved sizes, providing side hangers fixing in position,providing centre handers using Ms rods amn chains etc. displaying scope of services, room numbers, doctors rooms, HOD rooms, floor wise facilities ,radiation sinages, mandatory notification as directed by the engineer in charge with one side lettering for fixed in wall and both sides as in projected type etc. complete to detailed pre approved plan.<br>Name board rooms -60x15cm - one side<br>

od56198/2022_2023 : Providing acrylic LED multi language letter (engilsh & malayalam) singaes on the building using three dimensional acrylic channel LED lighting with high bright BGST 0.92 watt water peoof neutral white (280 K) LED modules as per detailed and approvd drawing including minimum 5 year varenty including lighting , placing in position and securing the sinages etc. as per the direction of engineer in charge.<br>

16.59.1 : Manufacturing, supplying and fixing retro reflective sign boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bi-lingual), symbols and borders etc. as per IRC: 67- 2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class-2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. angle iron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 Nos M.S. angles of size 35x35x5 mm to a vertical post made up to M.S. Tee section ISMT 50x50x6 mm welded with base plate of size 100x100x 5 mm at the bottom end and including making holes in pipes, angles flats, providing & fixing M.S. message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical MS-Tee support to be painted in black and white colours). Backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lifts etc. complete as per drawing , specification and direction of Engineer-in-Charge.Mandatory / Regulatory sign boards of 900 mm diametre with support length of 3750 mm

16.59.2 : Manufacturing, supplying and fixing retro reflective sign boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bi-lingual), symbols and borders etc. as per IRC: 67- 2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class-2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. angle iron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 Nos M.S. angles of size 35x35x5 mm to a vertical post made up to M.S. Tee section ISMT 50x50x6 mm welded with base plate of size 100x100x 5 mm at the bottom end and including making holes in pipes, angles flats, providing & fixing M.S. message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical MS-Tee support to be painted in black and white colours). Backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lifts etc. complete as per drawing , specification and direction of Engineer-in-Charge.Cautionary / warning sign boards of equilateral triangular shape having each side of 900 mm with support length of 3650 mm

16.61 : Providing Retro - reflective regulatory sign board of size 900 mm diameter made out of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated lens type retro reflective sheeting as approved by Engineer-in-Charge. Letter, symbols, borders etc. will be as per IRC. 67 with required colour scheme on the boards and with the high intensity grade A. The aluminium sheet to be riveted to M.S. frame of M.S. angle 50x50x4 mm , 4 m long welded to the frame with adequate anti-theft arrangement. Sheet work to be painted with two or more coats of synthetic enamel paint over an under coat ( primer ) and back side of aluminium sheet to be painted with two or more coats of epoxy paint including appropriate priming coat complete in all respects as per direction of Engineer- in-charge .

630kVA 11kV/433V Cast Resin (Dry type) Indoor USS Transformer

od55515/2022_2023 : Supply, installation, testing & commissioning of 630kVA 11kV/433V 3 phase Unitized substation Vector DYN-11 , copper double wound, transformer with 630 AMPS 350 MVA LBS , and all other components/accessories and off circuit tappings from +5% to -10% in steps of 2.5%, changeable on offcircuit by tap links provided, with WTI & LV terminals suitable for 4 runs of A2XFY cable and, with incoming suitable for XLPE cable, with all other standard fittings and accessories confirming to IS:2026/77, 11171/85. including separate winding temperature indicator for each phase and core in the Transformer, with all accessories, complete as required as per State electricity board, ECBC, IE rules specifications. Losses shall be within the limits prescribed in KSECBC 2017. Total losses for the transformer should conform to IS 2026:part 11 2007. Maximum losses at 50% loading should be less than 4.5kW and maximum losses at 100% loading should be less than 12kW. Seperate metering class CT & PT should be provided for periodic loss monitoring using digital meter. Transformer and all accesories included shall be supplied with warranty against manufacturing /defects/ damages during the entire defects liability period. No excemption in any components will be accepted. Cable entry & outgoing for transformer shall be as per site coniditon,to be confirmed before manufacturing. Colling shall be ANAN. Push button for emergency OFF shall be placed outside in seperate enclosure, painted in red covered by glass. <br>

HT PANEL BOARD

od55534/2022_2023 : Supply, installation, testing and commissioning of dust and vermin proof floor mounted free standing cubicle type, 11kV, extensible panel board made out of metal clad fully compartmentalised complete with hinged and earthed front doors interlocked with the earth switch, comprising of one number of 630A VCB as incomer with two numbers of 630A VCB as outgoings as per the specification details below. Panel shall be factory fitted type with type testing certificates as per IEC 62271 Part 100(for VCB) & Part 200(for enclosure). Panel shall be supplied with warranty against manufacturing / maintenance defects/ damages by manufacturer during the entire defects liability period. No excemption in any components will be accepted for warranty exemptions. All CTs & PTs shall be type tested as per standards and certificates shall be produced before supply of the panel test shall include but not limited to polarity test, high voltage power-frequency one minute withstand test, induced over voltage test, partial discharge measurement, accuracy test, intertum insultation test, dimension check, ratio and phase angle error test etc. Insulation resistance test and fuctional testes of panel and VCB shall be produced. Fuctuional tests shall include but not be limited to mechanical operation test for opening and closing under no load condition, master trip relay and auxilary relays, over current and earth fault relay test, breaker rack IN and Rack OUT , MFM, voltmeter, ammeter and all other meters programmed and checked, motor charging etc. Panel shall include all relays and tripping mechanisms and accesories as required as per KSEI standards. Cable entry & outgoing for transformer shall be as per site coniditon,to be confirmed before manufacturing. HT panel board shall be manufactured with provision for installing HT TOD bidirection meter in incomer side as per schematic layout with necessary CTs and all accesories as required. All VCBs shall be with Modbus communication protocol and RS485 and ethernet ports for incorporation with IBMS / EMS as required.<br>Incoming:<br>1no:-11kV 630A, 3phase 50Hz, 350MVA, breaking capacity vacuum circuit breaker dust and vermin proof totally enclosed in sheet steel housing, fully inter locked, horizontal draw out and horizontal isolation, indoor truck type with trip free spring closing mechanism with mechanical ON/OFF indicators, earthing terminals automatic safety shutters, complete with auxiliary contacts, resin cast CTs of suitable ratio and accuracy class for protection & metering(Class0.2 S). Contractor shall quote the price with 50/5A 0.2S class metering CT, but CT ratio shall be finalised as per contract demand during the course of work.<br>Draw out type resin cast P.T with inbuilt fuses of ratio 11kV/110V, CL :0.2S must be provided. Bus bar compartment shall have suitable capacity non-hygroscopic and high dieletric strength SMC/FRP busbar supports with electrolytic aluminium busbars covered with suitable sleeves. WIth breaker control switch, switch with plug point, strip heater, thermostat for space heater, cubicle lamp with switch, seal of bushings including all connections and interconnections. Metering compartments for mounting digital meter and numerical relays for feeder protection, shunt/series trip coil, under voltage release, indication lamps, spring charge, trip circuit healthy, alram, RYM indication cable entry boxes, including all interconnections, providing fire/heat resistant coatings for busbar & CB truck enclosures and powder coating complete panel as per IS-2516 & IS 3427 with latest amendments complete as required with manually charged spring closing system. It shall also be provided with Instantenous IDMT relay 2 O/C + 1 E/F relay CDAG-51 or Equivalent with high Set, Master Trip Relay. Provision shall be provided for fixing TOD meter including connections. Unidirectional Solar meter space provision on the LT compartment shall also be envisaged during construction for meter installaion by Solar agency for KSEB liasion<br>Out goings :<br>2 nos:-11kV 630A, 3phase 50Hz, 350MVA, breaking capacity vacuum circuit breaker dust and vermin proof totally enclosed in sheet steel housing, fully inter locked, horizontal draw out and horizontal isolation, indoor truck type with trip free spring closing mechanism with mechanical ON/OFF indicators, earthing terminals automatic safety shutters, complete with auxiliary contacts<br>Bus bar compartment shall have suitable capacity non-hygroscopic and high dieletric strength SMC/FRP busbar supports with electrolytic aluminium busbars covered with suitable sleeves. WIth breaker control switch, switch with plug point, strip heater, thermostat for space heater, cubicle lamp with switch, seal of bushings including all connections and interconnections. Metering compartments for mounting digital meter and numerical relays for feeder protection, shunt/series trip coil, under voltage release, indication lamps, spring charge, trip circuit healthy, alram, RYM indication cable entry boxes, including all interconnections, providing fire/heat resistant coatings for busbar & CB truck enclosures andpowder coating complete panel as per IS-2516 & IS 3427 with latest amendments complete as required with manually charged spring closing system. It shall also be provided with Instantenous IDMT relay 2 O/C + 1 E/F relay CDAG-51 or Equivalent with high Set, Master Trip Relay. <br>The panel shall include auxillary DC power supply unit, 24V, with required Ah capacity battery power pack including all accesories required for complete backup of all indicators, mechanisam and operating system in the panel with stationary type, high discharge perfomance,Valve Regulated Lead Acid (VRLA) sealed maintenance free battery, battery charger including all other accessories like battery rack, interconnecting cables etc as required The power pack and accesories shall be placed in the panel itself.<br>

HT CABLE SUPPLY & LAYING

od55540/2022_2023 : Supply of following 11kV (E), stranded compact Circular Aluminium Conductor, Conductor Screen With Extruded Semi Conducting Compound, XLPE Insulated, Insulation Screening with extruded Semi Conducting Compound in combination with Copper Tape, cores laid up, innersheath of PVC tape, galvanised flat steel strip armoured and overall PVC Sheathed Cable conforming to IS 7098 / (PART-II) 1985 with latest amendments.<br><br>3cx300sq.mm XLPE Cable<br>

od55552/2022_2023 : Laying of following 11kV (E) grade XLPE insulated PVC sheathed compact circular armoured aluminium conductor HT power cable, insulation screened with extruded semi conducting compound in separate existing cable tray/ on surface using factory made clamps and the spacing between clamps will not exceed 60cm.<br>Above 120 sq. mm and upto 400 sq. mm<br>

8.3.2 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.Above 120 sq. mm and upto 400 sq. mm

8.4.2 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size in the existing masonry open duct as required.Above 120 sq. mm and upto 400 sq. mm

BIDIRECTIONAL HT TOD NET METER

od55579/2022_2023 : Supply, Installation, testing & commissioning of 3 phase 4 wire according to IS14697-1999, CBIP-325, IS 159595A, class: 0.2S, Bidirectional TOD meter with RS485 port, LCD with backlit display of Electricity board approved make, in existing enclosures of HT panel including all necessary accessories for fixing and connection complete as required getting tested and approved from statutory authorities, providing connection/inter-connections as required for complete installation and as instructed by engineer in charge/consultant. <br><br>Supply,Installation, testing and commisioning<br>

HV CABLE END TERMINATION

10.4.4 : Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required:300 sq. mm

10.5.4 : Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :300 sq. mm

od55942/2022_2023 : Upgrading of existing HT supply point of the existing DP structure at site from which 11kV connection is taken, enhancing the supply point to carter to the newly proposed connected load and transformer rating, getting approvals, submitting completion certificates, upgrading the existing DP structure components such as HT fuses, AB switch and making new the damages, removing the existing HT cable connections for providing new cable connection, complete as required for taking cable connection to the new transformer for the premisis, making the entire premiss as a single HT consumer, making necessary changes and getting approvals complete as required<br>

DESIEL GENERATORS, EXHAUST PIPES & ALLIED WORKS

od55211/2022_2023 : 250kVA DESIEL GENERATORS<br>Supply, installation, testing and commissioning of radiator cooled 3 phase, 415V±0.1%, 0.8 pf 50hz. prime rated DG set of the rating 250 kVA comprising of diesel engine, alternator, fuel tank, starting system, battery, battery charger, electronic governor etc with all accessories required for load sharing with another DG set of same rating and automatic operation using AMF & PLC system, communication with PLC system etc, communication ports for integration with EMS & IBMS. The battery charger shall be included by the same manufacturer of auxillary DC power supply unit, with dry batteries with connecting leads and terminals with stationary type, high discharge perfomance, Valve Regulated Lead Acid (VRLA) sealed maintenance free battery and charger including all other accessories like interconnecting cables etc as required. The Generator set shall have a integral type acoustic enclosure as per latest CPCB II norms. <br>"The generator set shall be supplied in accordance but not limited with the following codes and standards - ISO 8528, ISO 3046, ISO 9001, BIS, CIEG, State electricity board regulation, BSI, state pollution control board, central pollution control board, Indian electricity rules , CPWD, IEC, ECBC & GRIHA standards, Alternator in accordance with IS: 4722/BS: 2613/IEC-34(Part-1), Specification for AC Generators driven by Reciprocating Engine: IS 13364(1-2)/1992, • Performance class of the DG SET Shall be as per ISO8528 to obtain following parameters - Steady-State Frequency Band = ≤0.5 %, Maximum Frequency Dip = ≤-7 %, Maximum Frequency Rise = ≤+10 %, Frequency Recovery Time - 3 sec, Steady-State Voltage Deviation = ≤ ± 1 %, Maximum Voltage Dip = ≤-15 %, Maximum Voltage Rise = ≤+20%, Voltage Recovery Time = 4 Sec. <br>"<br>The DG sets performance class shall be suitable to power highly non - linear loads. The supplier shall warrant the equipment to be free from defects in material and workmanship for the entire defects liability period. The Engine shall be suitable to drive alternator of base load application 24/7 operation. Engine/generator sets shall meet emergency power requirement to start and be on line within 10 seconds of onset of failure.<br>"Diesel Engine of required bhp, stationary type and four stroke with Inline cylinder arrangement shall be complete with integral air intake through suitable air filters and exhaust system, speed regulation system, fuel injection system, lube oil system, silencers, self-contained piping, instruments, mounted on anti-vibration mounts, turbo charged, multi- cylinder, 4-stroke, with continous power output at 1,500 r.p.m battery started .The engine shall have 10% overload capacity for one hour in every 12 hours of operation as per ISO. Fuel system shall comprise of fuel pump, fuel injectors, fuel filter, fuel hoses, lube oil pump, lube oil priming pump, lube oil filter, bypass filter etc. The DG set shall be supplied with standard fuel tank as per manufacturer standard within the canopy itself. <br>"<br>Following protection/warning shall be provided but not limited to with the DG set, Engine over Speed Shutdown, Low Lube Oil Pressure Warning /Shutdown, High Coolant Temperature Warning / Shutdown, Low Coolant Level Warning / Shutdown, Low Coolant Temperature Warning, Low And High Battery Voltage Warning, Weak Battery Warning, Dead Battery Shutdown, Over Crank Shutdown, Fail To Crank Shutdown. The governor shall be Electronic type confirming complete with Display unit and shall be a self-contained unit capable of monitoring speed.The engine/generator sets shall be provided with electronic governors suitable for unattended automatic paralleling and load sharing. <br>"The DG Set shall be supplied with micro-processor based generator monitoring, metering & protection feature with display viz Analogue & Digital AC output metering, Battery monitoring system to sense and warn against a weak battery condition.,Digital alarm & status message display, Overload, Overcurrent, Over voltage, Under voltage, Over frequency, Under frequency, Reverse Power Relay, Restricted Earth Fault<br>"<br>Controller shall be equiped with auto, manual, start, stop, fault reset and lamp test/panel lamp switches with alpha-numeric displays and push buttons, indications for genset running, remote start, not in auto, common shutdown, common warning, manual run mode, auto mode, stop etc with sync check. For alternator - line to neutral and line to line volts indication, current, frequency, kW, kVAr, power factor kVA and for engine following indications - DC voltage, engine speed, lube oil pressure, coolant temperature, coolant low level, comprehensive data, with start/stop attempts, runnings hours, kW hours, load profile, fault history, datta logging etc and all data shall be recoreded. Generator shall be including dust and vermin proof, type standard control panel board within the canopy, comprising of one number Microprocessor based MCCB rating of 400A, 4pole, 36 kA breaking capacity, thermal over load, voltage controlled O/C relay, over voltage, under voltage, negative sequence relay, voltmeter with selector switch, 3 ammeters of 0-400A range, frequency meter, kW, pf, electronic energy meter with CTs and indicating lamps with fuse and switch control etc. as complete with necessary control wiring interconnections etc. The DG controller shall be with necessary communication protocol to communicate the DG sets with PLC and IBMS<br>(Energy meters & CTs shall be tested and certificate shall be obtained from electrical inspectorate lab) Following sanction may be obtained by the contractor,<br>(i) Sanctions from Municipality/ Corporation<br>(ii) Sanction from Pollution control Board<br>(ii) Sanction from electrical inspectorate<br>Outdoor acoustic enclosure for the DG set. The sound level shall be brought down to 70DB+/-5 with at a distance of 1m (as per CPCB norms the sound level shall be 75dB at a distance of 1m from the silencer at the top of the enclosure).Accoustic enclosure shall be provided as per manufacturer standards confirmining to CPWD standards mentioned. Doors shall be openable on either side.Sufficient fresh air intake and hot air outlet with splitters to be arranged so that the temperature inside should not increase to 5 degree above ambient temperature. (The enclosure shall bare certificate from the generator manufacturer conforming the CPCB II norms and serial numbers of the test certificate).The supply of DG set shall include first filling of oil and lube for commissioning of the DG set. Push button for emergency OFF shall be placed outside in seperate enclosure, painted in red covered by glass.<br>Supply, Installation, testing and commisioning<br>

EXHAUST PIPES

od55224/2022_2023 : Supply, erection, commissioning of additional length of exhaust pipes with long radius bend from residential silencer with necessary clamps, fixtures, etc painted with heat resistant, rust proof, bituminous paint of approved colors to a maximum of 10 m in stages of following sizes including suitable rain cap at top to avoid rain water entry. The distance between exhaust pipe at top and rain cap should be higher than diameter of pipe. It is also recommended that horizontal run of exhaust piping should slope downwards away from engine to the condensate trap. Silencer should be installed with drain plug at bottom. Fixing shall be done with proper clamps, expansion bolts, and all other acessories as instructed by the Engineer and the rate inclusive of all minor civil works required, bolts, clamps etc as required for istallation. Support to exhaust piping should be done in such a manner that load of exhaust piping is not exerted to turbocharger. Exhaust pipe height shall be 3m more than the top of any adjacent building withing 10m radius of the exhaust.<br>150mm dia <br>

od55245/2022_2023 : Supply & providing thermal insulation for silencer with inner glass wool and providing aluminium cladding for DG set silencer as per standards.<br>

od55445/2022_2023 : Supply & providing insulation for exhaust pipe with thermal insulation and providing aluminium cladding as per standards.<br>

od55469/2022_2023 : DG set commisioning of both 250kVA DG sets including Trial run of DG sets on no-load and variable load condition and to record the parameters as per prescribed format as per manufacturer standards. Cost of consumable ( fuel oil, lube oil, etc.) to be borne by Contractor. This shall also include first fill of diesel for commisiong of the DG set. Full tank Diesel shall be filled for initial commisioning for both DG .<br>

EXHAUST PIPES - CIVIL ITEMS

10.2 : Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

CPRI CERTIFIED MV PANELS AS PER IS 8623

od56799/2022_2023 : MAIN PANEL <br>Incomer -<br>EB Incomer - 1000A 50kA FP EDO Microprocessor based ACB with 3 O/C and 1 E/F releases. Standby low set E/F relay with CT at neutral earthing strip -1 No.<br>DG Incomer 1 & 2 - 400A 36 kA FP MCCB Microprocessor based with 400A FP Contactor- 2 Nos. <br>1000A,FP,50kA.EDO Microprocessor based Buscoupler- 1 no<br>1000A 433V best conductivity extensible Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required, as per IEC norms<br>RYB phase indicating LED lamps with control fuses and switches - 3 set.<br>Multifunction meter as per IEC 62053-21, specified above including CTs and all accesories- 3 set<br>All CTs as required for complete installation<br>Class B Surge arrestor with HRC fuses for backup as per manufacturer standard, including copper cable connection between arrestor and fuses - 2 set<br>Reverse power relay with CTs and accessories - 2 nos<br>PLC with demand controller and auto main faiuler feature to automatically turn ON each DG set automatically during power supply failure, including turning ON DG sets as per confirmed interlocking chart, turning ON/OFF as per demand, complete control of DG set as required, including PLC, and all other accesoires and connections complete as required<br>Outgoings<br>500A 36kA TP Microprocessor based MCCB - 2 nos<br>400A 36kA TP Microprocessor based MCCB - 1 no<br>320A 36kA TP Microprocessor based MCCB - 4 nos<br>250A 36kA TP Microprocessor based MCCB - 1 no<br>315A FP Isolator - 1 no<br>Multifunction meter as per IEC 62053-21, specified above including CTs and all accessories - 8 set<br>

od56802/2022_2023 : UPS IN PANEL <br>Fabrication, supply, erection, testing and commissioning of dust and vermin proof, floor / wall mounted, front operated MV panel board as per IS 8623, CPRI Certified, compartmentalised (minimum form 3b) complete with hinged and earthed front doors with name plate, danger notice board, heavy duty rubber gaskets, removable gland plates made out of 3mm thick sheet steel including all components as shown in the schematic drawing. All opening parts of the panel shall be sealable. These panel should include surge arrester Class B or Class B+C/ Class 1+2 as per IEC 61643 (IP 20) with remote indication for defective arresters, arrester Spark Gap type to connect between Neutral and Earth.complete with back up fuse for SPD protection as per manufacturer standard. Providing all connections and interconnections as required and providing all accessories as required for complete installation as instructed by engineer in charge/consultant and as shown in the schematic layout provided. All switchgears shall be with with spreader links and rotary handle. Providing all connections and interconnections as required and providing all accessories as required for complete installation as instructed by engineer in charge/consultant and as shown in the schematic layout provided. Necessary electrical and mechanical interlocking arrangements shall be provided as per scehmatic drawing to achieve operational functionalityAll panels shall be with separate channels isolated from LT cable chambers for running of RS485 & other ELV cables for integration with EMS & IBMS. Switchgears and meters shall be with necessary communication ports for integration with BMS & EMS and Potential free contacts for BMS. All panel meters should be with RS485 ports for EMS integration. All Multifunction meter shall be as per IEC 62053-21, class 1, having multiline LED display with following parameters -Phase wise instantaneous and Average values – Voltage, Current, Power Factor, Phase wise instantaneous and Average values – Active Power, Reactive Power lead & lag, Apparent Power, Import & Export Cumulative values– Active Energy, Reactive Energy lead & lag, Apparent Energy, 4. PF for 3 phases and average,Instantaneous Frequency,Total Harmonics Distortion – Phase wise Voltage and Phase wise Current, Min and max of VLL, VLN, A, F, W, VA, VAr, PF with date and time stamp,Battery backed RTC with 2 years of power down time, Demand calculations based on W, VA, VAr, 10. Demand sync – Sliding window or block window site selectable, Demand interval: 5 to 30 min, Individual harmonics upto 15th order for voltage and current, Percentage Unbalance – Voltage and Current, Cumulative Run Hours, Sampling rate of 64 samples / cycle, Measuring circuit burden should be lesser than 0.2 VA, Aux burden < 5VA, Meter shall be suitable for CT secondary 1A /5A including CTs, site programmable CT & PT ratio, Meters shall have RS485 port with MODBUS RTU protocol, with IP 51 protection from front end preventing dust and moisture entry, meters shall be capable of integration with EMS SoftwareAll opening parts of the panel shall be sealable. Panels shall be complete with Al bus bars, separate earth bus bar to be provided through out the length of the panel along with base chanel of suitable size, cable alleys as per requirement, complete, numbering, danger plate etc as required as per specifications and drawings. Current density for busbarsize shall be designed considering not more than 0.8 A/sq.mm for aluminium. The switchgear live parts shall be isolated with proper insulation material. All switchgears shall be with spreader links, operating knobs/handles, DIN rail provision for isolators with required cable alleys. The panel design shall be in accordance with IS & Kerala state norms. All panels shall be cable alleys and seperate bus bar compartments for easy terminations as per KSEI standards with proper clearances. <br>Incomer -<br>320A 36kA FP Microprocessor based MCCB - 1 nos<br>320A 433V best conductivity extensible Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required, as per IEC norms<br>RYB phase indicating LED lamps with control fuses and switches - 1 set.<br>Class B Surge arrestor with HRC fuses for backup as per manufacturer standard, including copper cable connection between arrestor and fuses - 1 set<br>Outgoings<br>160A 36 kA FP MCCB Microprocessor based - 3 Nos. <br>RYB phase indicating LED lamps with control fuses and switches - 3 set.<br>Multifunction meter as per IEC 62053-21, specified above including CTs and all accessories - 3 set<br>

od56841/2022_2023 : UPS OUT PANEL <br>Fabrication, supply, erection, testing and commissioning of dust and vermin proof, floor / wall mounted, front operated MV panel board as per IS 8623, CPRI Certified, compartmentalised (minimum form 3b) complete with hinged and earthed front doors with name plate, danger notice board, heavy duty rubber gaskets, removable gland plates made out of 3mm thick sheet steel including all components as shown in the schematic drawing. All opening parts of the panel shall be sealable. These panel should include surge arrester Class B or Class B+C/ Class 1+2 as per IEC 61643 (IP 20) with remote indication for defective arresters, arrester Spark Gap type to connect between Neutral and Earth.complete with back up fuse for SPD protection as per manufacturer standard. Providing all connections and interconnections as required and providing all accessories as required for complete installation as instructed by engineer in charge/consultant and as shown in the schematic layout provided. All switchgears shall be with with spreader links and rotary handle. Providing all connections and interconnections as required and providing all accessories as required for complete installation as instructed by engineer in charge/consultant and as shown in the schematic layout provided. Necessary electrical and mechanical interlocking arrangements shall be provided as per scehmatic drawing to achieve operational functionalityAll panels shall be with separate channels isolated from LT cable chambers for running of RS485 & other ELV cables for integration with EMS & IBMS. Switchgears and meters shall be with necessary communication ports for integration with BMS & EMS and Potential free contacts for BMS. All panel meters should be with RS485 ports for EMS integration. All Multifunction meter shall be as per IEC 62053-21, class 1, having multiline LED display with following parameters -Phase wise instantaneous and Average values – Voltage, Current, Power Factor, Phase wise instantaneous and Average values – Active Power, Reactive Power lead & lag, Apparent Power, Import & Export Cumulative values– Active Energy, Reactive Energy lead & lag, Apparent Energy, 4. PF for 3 phases and average,Instantaneous Frequency,Total Harmonics Distortion – Phase wise Voltage and Phase wise Current, Min and max of VLL, VLN, A, F, W, VA, VAr, PF with date and time stamp,Battery backed RTC with 2 years of power down time, Demand calculations based on W, VA, VAr, 10. Demand sync – Sliding window or block window site selectable, Demand interval: 5 to 30 min, Individual harmonics upto 15th order for voltage and current, Percentage Unbalance – Voltage and Current, Cumulative Run Hours, Sampling rate of 64 samples / cycle, Measuring circuit burden should be lesser than 0.2 VA, Aux burden < 5VA, Meter shall be suitable for CT secondary 1A /5A including CTs, site programmable CT & PT ratio, Meters shall have RS485 port with MODBUS RTU protocol, with IP 51 protection from front end preventing dust and moisture entry, meters shall be capable of integration with EMS SoftwareAll opening parts of the panel shall be sealable. Panels shall be complete with Al bus bars, separate earth bus bar to be provided through out the length of the panel along with base chanel of suitable size, cable alleys as per requirement, complete, numbering, danger plate etc as required as per specifications and drawings. Current density for busbarsize shall be designed considering not more than 0.8 A/sq.mm for aluminium. The switchgear live parts shall be isolated with proper insulation material. All switchgears shall be with spreader links, operating knobs/handles, DIN rail provision for isolators with required cable alleys. The panel design shall be in accordance with IS & Kerala state norms. All panels shall be cable alleys and seperate bus bar compartments for easy terminations as per KSEI standards with proper clearances. <br>Incomer -<br>160A 36 kA FP MCCB Microprocessor based - 3 Nos. <br>320A 433V best conductivity extensible Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required, as per IEC norms<br>Multifunction meter as per IEC 62053-21, specified above including CTs and all accessories - 3 set<br>RYB phase indicating LED lamps with control fuses and switches - 3 set.<br>Class B Surge arrestor with HRC fuses for backup as per manufacturer standard, including copper cable connection between arrestor and fuses - 1 set<br>Outgoings<br>320A 36kA FP Microprocessor based MCCB - 1 no<br>RYB phase indicating LED lamps with control fuses and switches - 1 set.<br>

od56849/2022_2023 : 150 kVAr APFC PANEL<br>Fabrication, supply, erection, testing and commissioning of dust and vermin proof, floor / wall mounted, front operated MV panel board as per IS 8623, CPRI Certified, compartmentalised (minimum form 3b) complete with hinged and earthed front doors with name plate, danger notice board, heavy duty rubber gaskets, removable gland plates made out of 3mm thick sheet steel including all components as shown in the schematic drawing. All opening parts of the panel shall be sealable. These panel should include surge arrester Class B or Class B+C/ Class 1+2 as per IEC 61643 (IP 20) with remote indication for defective arresters, arrester Spark Gap type to connect between Neutral and Earth.complete with back up fuse for SPD protection as per manufacturer standard. Providing all connections and interconnections as required and providing all accessories as required for complete installation as instructed by engineer in charge/consultant and as shown in the schematic layout provided. All switchgears shall be with with spreader links and rotary handle. Providing all connections and interconnections as required and providing all accessories as required for complete installation as instructed by engineer in charge/consultant and as shown in the schematic layout provided. Necessary electrical and mechanical interlocking arrangements shall be provided as per scehmatic drawing to achieve operational functionalityAll panels shall be with separate channels isolated from LT cable chambers for running of RS485 & other ELV cables for integration with EMS & IBMS. Switchgears and meters shall be with necessary communication ports for integration with BMS & EMS and Potential free contacts for BMS. All panel meters should be with RS485 ports for EMS integration. All Multifunction meter shall be as per IEC 62053-21, class 1, having multiline LED display with following parameters -Phase wise instantaneous and Average values – Voltage, Current, Power Factor, Phase wise instantaneous and Average values – Active Power, Reactive Power lead & lag, Apparent Power, Import & Export Cumulative values– Active Energy, Reactive Energy lead & lag, Apparent Energy, 4. PF for 3 phases and average,Instantaneous Frequency,Total Harmonics Distortion – Phase wise Voltage and Phase wise Current, Min and max of VLL, VLN, A, F, W, VA, VAr, PF with date and time stamp,Battery backed RTC with 2 years of power down time, Demand calculations based on W, VA, VAr, 10. Demand sync – Sliding window or block window site selectable, Demand interval: 5 to 30 min, Individual harmonics upto 15th order for voltage and current, Percentage Unbalance – Voltage and Current, Cumulative Run Hours, Sampling rate of 64 samples / cycle, Measuring circuit burden should be lesser than 0.2 VA, Aux burden < 5VA, Meter shall be suitable for CT secondary 1A /5A including CTs, site programmable CT & PT ratio, Meters shall have RS485 port with MODBUS RTU protocol, with IP 51 protection from front end preventing dust and moisture entry, meters shall be capable of integration with EMS SoftwareAll opening parts of the panel shall be sealable. Panels shall be complete with Al bus bars, separate earth bus bar to be provided through out the length of the panel along with base chanel of suitable size, cable alleys as per requirement, complete, numbering, danger plate etc as required as per specifications and drawings. Current density for busbarsize shall be designed considering not more than 0.8 A/sq.mm for aluminium. The switchgear live parts shall be isolated with proper insulation material. All switchgears shall be with spreader links, operating knobs/handles, DIN rail provision for isolators with required cable alleys. The panel design shall be in accordance with IS & Kerala state norms. All panels shall be cable alleys and seperate bus bar compartments for easy terminations as per KSEI standards with proper clearances.<br> 150 kVAr with 7% harmonic block reactor copper wound with tuned heavy duty box type capacitors with heavy duty polypropylene as a dielectric with vaccum deposited conductors on the polypropylene as electrodes using contactor swtiching, using Microprocessor based relay operated controller with 8 stage which should be capable to switch on the required kVAr for compensation based on cyclic switching. All controls shall be mounted on enclosure door with door interlocks. Heavy duty capacitor duty contactors with high rupturing MCCB shall be used for individual stage control. Box type heavy duty capacitor with following characteristics but not limited to- Over current withstand capability 1.8 x In, Operating losses < 0.35 W/kVAr, Peak Inrush current withstand capability 300 x In, and Max. Temperature of 55ºC and long operating life. Each capacitor shall be in seperate compartment<br>Incomer - 400A 36kA 4P MCCB, microprocessor based with high rupturing capacity and in built overload and short circuit releases as per specifications as incomer <br>400A 433V best conductivity extensible Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required, as per IEC norms<br>Class B Surge arrestor with HRC fuses for backup as per manufacturer standard, including copper cable connection between arrestor and fuses - 1 set<br>RYB phase indicating LED lamps with control fuses and switches - 1 set.<br>Multifunction meter as per IEC 62053-21, specified above including CTs and all accessories - 1 set<br>8 stage APFC relay - 1 no<br>APFC panel capacitor segregation to achieve 150 kVAr shall be as below -<br>125A TP high rupturing capacity MCCB with 125A TP contactor for 2 nos x 27.7 kVAr Capacitors in parallel with 7% harmonic block reactor - 1 set<br>63A TP high rupturing capacity MCCB with 63A TP contactor for 27.7 kVAr Capacitor with 7% harmonic block reactor - 1 set<br>50A TP high rupturing capacity MCCB with 50A TP contactor for 20 kVAr Capacitor with 7% harmonic block reactor - 1 set<br>32A TP high rupturing capacity MCCB with 32A TP contactor for 11.1 kVAr Capacitor with 7% harmonic block reactor - 1 set<br>16A TP high rupturing capacity MCCB with 16A TP contactor for 4.4 kVAr Capacitor with 7% harmonic block reactor - 1 set<br>10A TP high rupturing capacity MCCB with 10A TP contactor for 3.3 kVAr Capacitor with 7% harmonic block reactor - 2 set<br>100A TP high rupturing capacity MCCB for (2 x 20 kVAr = 40 kVAr) Capacitor to be connected for No Load Compensation directly to transformer - 1 set<br>"All compartments shall be with Push Buttons, R Y B Indication with control fuse -1Set, Automanual selector switch- 1No , Forced cooling using fans (both manual and automatic operation of fans should be possible with Auto/Manual toggle) including all connections and interconnections, all accesories as required for complete installation as instructed by engineer in charge/consultant. <br>"<br>

od56853/2022_2023 : FIRE PANEL <br>Incomer -<br>315A TPN Isolator - 1 No.<br>315A 433V, 25kA best conductivity extensible Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required. Necessary interlocking arrangement<br>RYB phase indicating LED lamps with control fuses and switches - 1 set.<br>Surge Protection Device Class B+C/ Class 1+2 with HRC fuses for backup as per manufacturer standard, including copper cable connection between arrestor and fuses - 1 set<br>Outgoings<br>200A TP ISOLATOR for 50HP pump along with starter w/o OLR, controllers, PB, indicators and all other accessories required as per fire norms - 1 no.<br>63A TP ISOLATOR for 12HP pump along with starter w/o OLR, controllers, PB, indicators and all other accessories required as per fire norms - 1 nos.<br>63A TP ISOLATOR - 1 nos.<br>Multifunction meter as per IEC 62053-21, specified above including CTs and all accessories - 1 set<br>

od56875/2022_2023 : UTILITY PANEL <br>Incomer -<br>250A FP Isolator - 1 No.<br>63A 25kA FP Thermal magnetic based MCCB - 1 no<br>250A 433V, 25kA best conductivity extensible Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required. <br>RYB phase indicating LED lamps with control fuses and switches - 2 set.<br>Multifunction meter as per IEC 62053-21, specified above including CTs and all accessories - 2 set<br>Surge Protection Device Class B with HRC fuses for backup as per manufacturer standard, including copper cable connection between arrestor and fuses - 1 set<br>Outgoings<br>100A 25kA TP Thermal Magnetic Based MCCB - 5 nos<br>63A 25kA TP Thermal Magnetic Based MCCB - 3 nos<br>Multifunction meter as per IEC 62053-21, specified above including CTs and all accessories - 8 set<br>

od56893/2022_2023 : MEDICAL GAS PANEL<br>Fabrication, supply, erection, testing and commissioning of dust and vermin proof, floor / wall mounted, front operated MV panel board as per IS 8623, CPRI Certified, compartmentalised (minimum form 3b) complete with hinged and earthed front doors with name plate, danger notice board, heavy duty rubber gaskets, removable gland plates made out of 3mm thick sheet steel including all components as shown in the schematic drawing. All opening parts of the panel shall be sealable. These panel should include surge arrester Class B or Class B+C/ Class 1+2 as per IEC 61643 (IP 20) with remote indication for defective arresters, arrester Spark Gap type to connect between Neutral and Earth.complete with back up fuse for SPD protection as per manufacturer standard. Providing all connections and interconnections as required and providing all accessories as required for complete installation as instructed by engineer in charge/consultant and as shown in the schematic layout provided. All switchgears shall be with with spreader links and rotary handle. Providing all connections and interconnections as required and providing all accessories as required for complete installation as instructed by engineer in charge/consultant and as shown in the schematic layout provided. <br>Necessary electrical and mechanical interlocking arrangements shall be provided as per scehmatic drawing to achieve operational functionality<br>All panels shall be with separate channels isolated from LT cable chambers for running of RS485 & other ELV cables for integration with EMS & IBMS. Switchgears and meters shall be with necessary communication ports for integration with BMS & EMS and Potential free contacts for BMS. All panel meters should be with RS485 ports for EMS integration. <br>All Multifunction meter shall be as per IEC 62053-21, class 1, having multiline LED display with following parameters -Phase wise instantaneous and Average values – Voltage, Current, Power Factor, Phase wise instantaneous and Average values – Active Power, Reactive Power lead & lag, Apparent Power, Import & Export Cumulative values– Active Energy, Reactive Energy lead & lag, Apparent Energy, 4. PF for 3 phases and average,Instantaneous Frequency,Total Harmonics Distortion – Phase wise Voltage and Phase wise Current, Min and max of VLL, VLN, A, F, W, VA, VAr, PF with date and time stamp,Battery backed RTC with 2 years of power down time, Demand calculations based on W, VA, VAr, 10. Demand sync – Sliding window or block window site selectable, Demand interval: 5 to 30 min, Individual harmonics upto 15th order for voltage and current, Percentage Unbalance – Voltage and Current, Cumulative Run Hours, Sampling rate of 64 samples / cycle, Measuring circuit burden should be lesser than 0.2 VA, Aux burden < 5VA, Meter shall be suitable for CT secondary 1A /5A including CTs, site programmable CT & PT ratio, Meters shall have RS485 port with MODBUS RTU protocol, with IP 51 protection from front end preventing dust and moisture entry, meters shall be capable of integration with EMS Software<br>All opening parts of the panel shall be sealable. Panels shall be complete with Al bus bars, separate earth bus bar to be provided through out the length of the panel along with base chanel of suitable size, cable alleys as per requirement, complete, numbering, danger plate etc as required as per specifications and drawings. Current density for busbarsize shall be designed considering not more than 0.8 A/sq.mm for aluminium. The switchgear live parts shall be isolated with proper insulation material. All switchgears shall be with spreader links, operating knobs/handles, DIN rail provision for isolators with required cable alleys. The panel design shall be in accordance with IS & Kerala state norms. All panels shall be cable alleys and seperate bus bar compartments for easy terminations as per KSEI standards with proper clearances. <br>Incomer -<br>100A FP Isolator - 1 no<br>100A 433V, 25kA best conductivity extensible Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required. <br>RYB phase indicating LED lamps with control fuses and switches - 1 set.<br>Surge Protection Device Class B+C/ Class 1+2 with HRC fuses for backup as per manufacturer standard, including copper cable connection between arrestor and fuses - 1 set<br>Outgoings<br>63A 16kA TP Thermal Magnetic Based MCCB - 7 nos<br>

od56895/2022_2023 : LIFT PANEL 2<br>Fabrication, supply, erection, testing and commissioning of dust and vermin proof, floor / wall mounted, front operated MV panel board as per IS 8623, CPRI Certified, compartmentalised (minimum form 3b) complete with hinged and earthed front doors with name plate, danger notice board, heavy duty rubber gaskets, removable gland plates made out of 3mm thick sheet steel including all components as shown in the schematic drawing. All opening parts of the panel shall be sealable. These panel should include surge arrester Class B or Class B+C/ Class 1+2 as per IEC 61643 (IP 20) with remote indication for defective arresters, arrester Spark Gap type to connect between Neutral and Earth.complete with back up fuse for SPD protection as per manufacturer standard. Providing all connections and interconnections as required and providing all accessories as required for complete installation as instructed by engineer in charge/consultant and as shown in the schematic layout provided. All switchgears shall be with with spreader links and rotary handle. Providing all connections and interconnections as required and providing all accessories as required for complete installation as instructed by engineer in charge/consultant and as shown in the schematic layout provided. <br>Necessary electrical and mechanical interlocking arrangements shall be provided as per scehmatic drawing to achieve operational functionality<br>All panels shall be with separate channels isolated from LT cable chambers for running of RS485 & other ELV cables for integration with EMS & IBMS. Switchgears and meters shall be with necessary communication ports for integration with BMS & EMS and Potential free contacts for BMS. All panel meters should be with RS485 ports for EMS integration. <br>All Multifunction meter shall be as per IEC 62053-21, class 1, having multiline LED display with following parameters -Phase wise instantaneous and Average values – Voltage, Current, Power Factor, Phase wise instantaneous and Average values – Active Power, Reactive Power lead & lag, Apparent Power, Import & Export Cumulative values– Active Energy, Reactive Energy lead & lag, Apparent Energy, 4. PF for 3 phases and average,Instantaneous Frequency,Total Harmonics Distortion – Phase wise Voltage and Phase wise Current, Min and max of VLL, VLN, A, F, W, VA, VAr, PF with date and time stamp,Battery backed RTC with 2 years of power down time, Demand calculations based on W, VA, VAr, 10. Demand sync – Sliding window or block window site selectable, Demand interval: 5 to 30 min, Individual harmonics upto 15th order for voltage and current, Percentage Unbalance – Voltage and Current, Cumulative Run Hours, Sampling rate of 64 samples / cycle, Measuring circuit burden should be lesser than 0.2 VA, Aux burden < 5VA, Meter shall be suitable for CT secondary 1A /5A including CTs, site programmable CT & PT ratio, Meters shall have RS485 port with MODBUS RTU protocol, with IP 51 protection from front end preventing dust and moisture entry, meters shall be capable of integration with EMS Software<br>All opening parts of the panel shall be sealable. Panels shall be complete with Al bus bars, separate earth bus bar to be provided through out the length of the panel along with base chanel of suitable size, cable alleys as per requirement, complete, numbering, danger plate etc as required as per specifications and drawings. Current density for busbarsize shall be designed considering not more than 0.8 A/sq.mm for aluminium. The switchgear live parts shall be isolated with proper insulation material. All switchgears shall be with spreader links, operating knobs/handles, DIN rail provision for isolators with required cable alleys. The panel design shall be in accordance with IS & Kerala state norms. All panels shall be cable alleys and seperate bus bar compartments for easy terminations as per KSEI standards with proper clearances. <br>Incomer -<br>63A FP Modular Isolator - 1 no<br>63A 433V, 16kA best conductivity extensible Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required. <br>RYB phase indicating LED lamps with control fuses and switches - 1 set.<br>Surge Protection Device Class B+C/ Class 1+2 with HRC fuses for backup as per manufacturer standard, including copper cable connection between arrestor and fuses - 1 set<br>Outgoings<br>40A 100mA FP RCBO - 1 nos<br>25A 30mA DP RCBO - 1 no<br>25A best conductivity extensible Al SPN bus bar<br>6A SP MCB - 4 nos<br><br>

od56898/2022_2023 : LIFT PANEL 1<br>Fabrication, supply, erection, testing and commissioning of dust and vermin proof, floor / wall mounted, front operated MV panel board as per IS 8623, CPRI Certified, compartmentalised (minimum form 3b) complete with hinged and earthed front doors with name plate, danger notice board, heavy duty rubber gaskets, removable gland plates made out of 3mm thick sheet steel including all components as shown in the schematic drawing. All opening parts of the panel shall be sealable. These panel should include surge arrester Class B or Class B+C/ Class 1+2 as per IEC 61643 (IP 20) with remote indication for defective arresters, arrester Spark Gap type to connect between Neutral and Earth.complete with back up fuse for SPD protection as per manufacturer standard. Providing all connections and interconnections as required and providing all accessories as required for complete installation as instructed by engineer in charge/consultant and as shown in the schematic layout provided. All switchgears shall be with with spreader links and rotary handle. Providing all connections and interconnections as required and providing all accessories as required for complete installation as instructed by engineer in charge/consultant and as shown in the schematic layout provided. <br>Necessary electrical and mechanical interlocking arrangements shall be provided as per scehmatic drawing to achieve operational functionality<br>All panels shall be with separate channels isolated from LT cable chambers for running of RS485 & other ELV cables for integration with EMS & IBMS. Switchgears and meters shall be with necessary communication ports for integration with BMS & EMS and Potential free contacts for BMS. All panel meters should be with RS485 ports for EMS integration. <br>All Multifunction meter shall be as per IEC 62053-21, class 1, having multiline LED display with following parameters -Phase wise instantaneous and Average values – Voltage, Current, Power Factor, Phase wise instantaneous and Average values – Active Power, Reactive Power lead & lag, Apparent Power, Import & Export Cumulative values– Active Energy, Reactive Energy lead & lag, Apparent Energy, 4. PF for 3 phases and average,Instantaneous Frequency,Total Harmonics Distortion – Phase wise Voltage and Phase wise Current, Min and max of VLL, VLN, A, F, W, VA, VAr, PF with date and time stamp,Battery backed RTC with 2 years of power down time, Demand calculations based on W, VA, VAr, 10. Demand sync – Sliding window or block window site selectable, Demand interval: 5 to 30 min, Individual harmonics upto 15th order for voltage and current, Percentage Unbalance – Voltage and Current, Cumulative Run Hours, Sampling rate of 64 samples / cycle, Measuring circuit burden should be lesser than 0.2 VA, Aux burden < 5VA, Meter shall be suitable for CT secondary 1A /5A including CTs, site programmable CT & PT ratio, Meters shall have RS485 port with MODBUS RTU protocol, with IP 51 protection from front end preventing dust and moisture entry, meters shall be capable of integration with EMS Software<br>All opening parts of the panel shall be sealable. Panels shall be complete with Al bus bars, separate earth bus bar to be provided through out the length of the panel along with base chanel of suitable size, cable alleys as per requirement, complete, numbering, danger plate etc as required as per specifications and drawings. Current density for busbarsize shall be designed considering not more than 0.8 A/sq.mm for aluminium. The switchgear live parts shall be isolated with proper insulation material. All switchgears shall be with spreader links, operating knobs/handles, DIN rail provision for isolators with required cable alleys. The panel design shall be in accordance with IS & Kerala state norms. All panels shall be cable alleys and seperate bus bar compartments for easy terminations as per KSEI standards with proper clearances. <br>Incomer -<br>100A FP Modular Isolator - 1 no<br>100A 433V, 16kA best conductivity extensible Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required. <br>RYB phase indicating LED lamps with control fuses and switches - 1 set.<br>Surge Protection Device Class B+C/ Class 1+2 with HRC fuses for backup as per manufacturer standard, including copper cable connection between arrestor and fuses - 1 set<br>Outgoings<br>40A 100mA FP RCBO - 2 nos<br>25A 30mA DP RCBO - 1 no<br>25A best conductivity extensible Al SPN bus bar<br>6A SP MCB - 6 nos<br>

od56901/2022_2023 : EXTERIOR LIGHTING PANEL<br>Fabrication, supply, erection, testing and commissioning of dust and vermin proof, floor / wall mounted, front operated MV panel board as per IS 8623, CPRI Certified, compartmentalised (minimum form 3b) complete with hinged and earthed front doors with name plate, danger notice board, heavy duty rubber gaskets, removable gland plates made out of 3mm thick sheet steel including all components as shown in the schematic drawing. All opening parts of the panel shall be sealable. These panel should include surge arrester Class B or Class B+C/ Class 1+2 as per IEC 61643 (IP 20) with remote indication for defective arresters, arrester Spark Gap type to connect between Neutral and Earth.complete with back up fuse for SPD protection as per manufacturer standard. Providing all connections and interconnections as required and providing all accessories as required for complete installation as instructed by engineer in charge/consultant and as shown in the schematic layout provided. All switchgears shall be with with spreader links and rotary handle. Providing all connections and interconnections as required and providing all accessories as required for complete installation as instructed by engineer in charge/consultant and as shown in the schematic layout provided. <br>Necessary electrical and mechanical interlocking arrangements shall be provided as per scehmatic drawing to achieve operational functionality<br>All panels shall be with separate channels isolated from LT cable chambers for running of RS485 & other ELV cables for integration with EMS & IBMS. Switchgears and meters shall be with necessary communication ports for integration with BMS & EMS and Potential free contacts for BMS. All panel meters should be with RS485 ports for EMS integration. <br>All Multifunction meter shall be as per IEC 62053-21, class 1, having multiline LED display with following parameters -Phase wise instantaneous and Average values – Voltage, Current, Power Factor, Phase wise instantaneous and Average values – Active Power, Reactive Power lead & lag, Apparent Power, Import & Export Cumulative values– Active Energy, Reactive Energy lead & lag, Apparent Energy, 4. PF for 3 phases and average,Instantaneous Frequency,Total Harmonics Distortion – Phase wise Voltage and Phase wise Current, Min and max of VLL, VLN, A, F, W, VA, VAr, PF with date and time stamp,Battery backed RTC with 2 years of power down time, Demand calculations based on W, VA, VAr, 10. Demand sync – Sliding window or block window site selectable, Demand interval: 5 to 30 min, Individual harmonics upto 15th order for voltage and current, Percentage Unbalance – Voltage and Current, Cumulative Run Hours, Sampling rate of 64 samples / cycle, Measuring circuit burden should be lesser than 0.2 VA, Aux burden < 5VA, Meter shall be suitable for CT secondary 1A /5A including CTs, site programmable CT & PT ratio, Meters shall have RS485 port with MODBUS RTU protocol, with IP 51 protection from front end preventing dust and moisture entry, meters shall be capable of integration with EMS Software<br>All opening parts of the panel shall be sealable. Panels shall be complete with Al bus bars, separate earth bus bar to be provided through out the length of the panel along with base chanel of suitable size, cable alleys as per requirement, complete, numbering, danger plate etc as required as per specifications and drawings. Current density for busbarsize shall be designed considering not more than 0.8 A/sq.mm for aluminium. The switchgear live parts shall be isolated with proper insulation material. All switchgears shall be with spreader links, operating knobs/handles, DIN rail provision for isolators with required cable alleys. The panel design shall be in accordance with IS & Kerala state norms. All panels shall be cable alleys and seperate bus bar compartments for easy terminations as per KSEI standards with proper clearances. <br>Incomer -<br>40A FP Modular Isolator - 1 no<br>40A 433V, 16kA best conductivity extensible Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required. <br>Astronomical time switch for automatic switching On & Off of street lights at sun set & sun rise or twilight (Auto ON, Auto Off, Auto modes) with manual override facility with 12/24 hour display format with suitable battery and indication for relay - 1 no.<br>40A TP Contactor - 1 no<br>RYB phase indicating LED lamps with control fuses and switches - 1 set.<br>Surge Protection Device Class B+C/ Class 1+2 with HRC fuses for backup as per manufacturer standard, including copper cable connection between arrestor and fuses - 1 set<br>Outgoings<br>25A TP MCB - 3 nos<br>25A SP MCB - 3 nos<br>

od56930/2022_2023 : PLUMBING PANEL<br>Fabrication, supply, erection, testing and commissioning of dust and vermin proof, floor / wall mounted, front operated MV panel board as per IS 8623, CPRI Certified, compartmentalised (minimum form 3b) complete with hinged and earthed front doors with name plate, danger notice board, heavy duty rubber gaskets, removable gland plates made out of 3mm thick sheet steel including all components as shown in the schematic drawing. All opening parts of the panel shall be sealable. These panel should include surge arrester Class B or Class B+C/ Class 1+2 as per IEC 61643 (IP 20) with remote indication for defective arresters, arrester Spark Gap type to connect between Neutral and Earth.complete with back up fuse for SPD protection as per manufacturer standard. Providing all connections and interconnections as required and providing all accessories as required for complete installation as instructed by engineer in charge/consultant and as shown in the schematic layout provided. All switchgears shall be with with spreader links and rotary handle. Providing all connections and interconnections as required and providing all accessories as required for complete installation as instructed by engineer in charge/consultant and as shown in the schematic layout provided. <br>Necessary electrical and mechanical interlocking arrangements shall be provided as per scehmatic drawing to achieve operational functionality<br>All panels shall be with separate channels isolated from LT cable chambers for running of RS485 & other ELV cables for integration with EMS & IBMS. Switchgears and meters shall be with necessary communication ports for integration with BMS & EMS and Potential free contacts for BMS. All panel meters should be with RS485 ports for EMS integration. <br>All Multifunction meter shall be as per IEC 62053-21, class 1, having multiline LED display with following parameters -Phase wise instantaneous and Average values – Voltage, Current, Power Factor, Phase wise instantaneous and Average values – Active Power, Reactive Power lead & lag, Apparent Power, Import & Export Cumulative values– Active Energy, Reactive Energy lead & lag, Apparent Energy, 4. PF for 3 phases and average,Instantaneous Frequency,Total Harmonics Distortion – Phase wise Voltage and Phase wise Current, Min and max of VLL, VLN, A, F, W, VA, VAr, PF with date and time stamp,Battery backed RTC with 2 years of power down time, Demand calculations based on W, VA, VAr, 10. Demand sync – Sliding window or block window site selectable, Demand interval: 5 to 30 min, Individual harmonics upto 15th order for voltage and current, Percentage Unbalance – Voltage and Current, Cumulative Run Hours, Sampling rate of 64 samples / cycle, Measuring circuit burden should be lesser than 0.2 VA, Aux burden < 5VA, Meter shall be suitable for CT secondary 1A /5A including CTs, site programmable CT & PT ratio, Meters shall have RS485 port with MODBUS RTU protocol, with IP 51 protection from front end preventing dust and moisture entry, meters shall be capable of integration with EMS Software<br>All opening parts of the panel shall be sealable. Panels shall be complete with Al bus bars, separate earth bus bar to be provided through out the length of the panel along with base chanel of suitable size, cable alleys as per requirement, complete, numbering, danger plate etc as required as per specifications and drawings. Current density for busbarsize shall be designed considering not more than 0.8 A/sq.mm for aluminium. The switchgear live parts shall be isolated with proper insulation material. All switchgears shall be with spreader links, operating knobs/handles, DIN rail provision for isolators with required cable alleys. The panel design shall be in accordance with IS & Kerala state norms. All panels shall be cable alleys and seperate bus bar compartments for easy terminations as per KSEI standards with proper clearances. <br>Incomer -<br>100A FP Isolator - 1 no<br>100A 433V, 25kA best conductivity extensible Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required. <br>RYB phase indicating LED lamps with control fuses and switches - 1 set.<br>Surge Protection Device Class B+C/ Class 1+2 with HRC fuses for backup as per manufacturer standard, including copper cable connection between arrestor and fuses - 1 set<br>Outgoings<br>63A TP MCB - 1 no<br>32A TP MCB - 15 nos<br>

od56934/2022_2023 : HVAC PANEL<br>Incomer -<br>500A FP Isolator - 1 no<br>500A 433V, 25kA best conductivity extensible Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required. <br>RYB phase indicating LED lamps with control fuses and switches - 1 set.<br>Surge Protection Device Class B with HRC fuses for backup as per manufacturer standard, including copper cable connection between arrestor and fuses - 1 set<br>Outgoings<br>200A 25kA TP MCCB - 2 nos<br>100A 25kA TP MCCB - 4 nos<br>63A 16kA TP MCCB - 3 nos<br>

od56935/2022_2023 : UPS MAIN PANEL<br>Fabrication, supply, erection, testing and commissioning of dust and vermin proof, floor / wall mounted, front operated MV panel board as per IS 8623, CPRI Certified, compartmentalised (minimum form 3b) complete with hinged and earthed front doors with name plate, danger notice board, heavy duty rubber gaskets, removable gland plates made out of 3mm thick sheet steel including all components as shown in the schematic drawing. All opening parts of the panel shall be sealable. These panel should include surge arrester Class B or Class B+C/ Class 1+2 as per IEC 61643 (IP 20) with remote indication for defective arresters, arrester Spark Gap type to connect between Neutral and Earth.complete with back up fuse for SPD protection as per manufacturer standard. Providing all connections and interconnections as required and providing all accessories as required for complete installation as instructed by engineer in charge/consultant and as shown in the schematic layout provided. All switchgears shall be with with spreader links and rotary handle. Providing all connections and interconnections as required and providing all accessories as required for complete installation as instructed by engineer in charge/consultant and as shown in the schematic layout provided. <br>Necessary electrical and mechanical interlocking arrangements shall be provided as per scehmatic drawing to achieve operational functionality<br>All panels shall be with separate channels isolated from LT cable chambers for running of RS485 & other ELV cables for integration with EMS & IBMS. Switchgears and meters shall be with necessary communication ports for integration with BMS & EMS and Potential free contacts for BMS. All panel meters should be with RS485 ports for EMS integration. <br>All Multifunction meter shall be as per IEC 62053-21, class 1, having multiline LED display with following parameters -Phase wise instantaneous and Average values – Voltage, Current, Power Factor, Phase wise instantaneous and Average values – Active Power, Reactive Power lead & lag, Apparent Power, Import & Export Cumulative values– Active Energy, Reactive Energy lead & lag, Apparent Energy, 4. PF for 3 phases and average,Instantaneous Frequency,Total Harmonics Distortion – Phase wise Voltage and Phase wise Current, Min and max of VLL, VLN, A, F, W, VA, VAr, PF with date and time stamp,Battery backed RTC with 2 years of power down time, Demand calculations based on W, VA, VAr, 10. Demand sync – Sliding window or block window site selectable, Demand interval: 5 to 30 min, Individual harmonics upto 15th order for voltage and current, Percentage Unbalance – Voltage and Current, Cumulative Run Hours, Sampling rate of 64 samples / cycle, Measuring circuit burden should be lesser than 0.2 VA, Aux burden < 5VA, Meter shall be suitable for CT secondary 1A /5A including CTs, site programmable CT & PT ratio, Meters shall have RS485 port with MODBUS RTU protocol, with IP 51 protection from front end preventing dust and moisture entry, meters shall be capable of integration with EMS Software<br>All opening parts of the panel shall be sealable. Panels shall be complete with Al bus bars, separate earth bus bar to be provided through out the length of the panel along with base chanel of suitable size, cable alleys as per requirement, complete, numbering, danger plate etc as required as per specifications and drawings. Current density for busbarsize shall be designed considering not more than 0.8 A/sq.mm for aluminium. The switchgear live parts shall be isolated with proper insulation material. All switchgears shall be with spreader links, operating knobs/handles, DIN rail provision for isolators with required cable alleys. The panel design shall be in accordance with IS & Kerala state norms. All panels shall be cable alleys and seperate bus bar compartments for easy terminations as per KSEI standards with proper clearances. <br>Incomer -<br>315A FP Isolator - 1 no<br>315A 433V, 36kA best conductivity extensible Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required. <br>RYB phase indicating LED lamps with control fuses and switches - 1 set.<br>Surge Protection Device Class B with HRC fuses for backup as per manufacturer standard, including copper cable connection between arrestor and fuses - 1 set<br>Outgoings<br>40A 25kA TP Thermal Magnetic based MCCB - 1 no.<br>100A 25kA TP Thermal Magnetic based MCCB - 7 nos.<br>Multifunction meter as per IEC 62053-21, specified above including CTs and all accessories - 8 set<br>

od56940/2022_2023 : SSB 1<br>Fabrication, supply, erection, testing and commissioning of dust and vermin proof, floor / wall mounted, front operated MV panel board as per IS 8623, CPRI Certified, compartmentalised (minimum form 3b) complete with hinged and earthed front doors with name plate, danger notice board, heavy duty rubber gaskets, removable gland plates made out of 3mm thick sheet steel including all components as shown in the schematic drawing. All opening parts of the panel shall be sealable. These panel should include surge arrester Class B or Class B+C/ Class 1+2 as per IEC 61643 (IP 20) with remote indication for defective arresters, arrester Spark Gap type to connect between Neutral and Earth.complete with back up fuse for SPD protection as per manufacturer standard. Providing all connections and interconnections as required and providing all accessories as required for complete installation as instructed by engineer in charge/consultant and as shown in the schematic layout provided. All switchgears shall be with with spreader links and rotary handle. Providing all connections and interconnections as required and providing all accessories as required for complete installation as instructed by engineer in charge/consultant and as shown in the schematic layout provided. <br>Necessary electrical and mechanical interlocking arrangements shall be provided as per scehmatic drawing to achieve operational functionality<br>All panels shall be with separate channels isolated from LT cable chambers for running of RS485 & other ELV cables for integration with EMS & IBMS. Switchgears and meters shall be with necessary communication ports for integration with BMS & EMS and Potential free contacts for BMS. All panel meters should be with RS485 ports for EMS integration. <br>All Multifunction meter shall be as per IEC 62053-21, class 1, having multiline LED display with following parameters -Phase wise instantaneous and Average values – Voltage, Current, Power Factor, Phase wise instantaneous and Average values – Active Power, Reactive Power lead & lag, Apparent Power, Import & Export Cumulative values– Active Energy, Reactive Energy lead & lag, Apparent Energy, 4. PF for 3 phases and average,Instantaneous Frequency,Total Harmonics Distortion – Phase wise Voltage and Phase wise Current, Min and max of VLL, VLN, A, F, W, VA, VAr, PF with date and time stamp,Battery backed RTC with 2 years of power down time, Demand calculations based on W, VA, VAr, 10. Demand sync – Sliding window or block window site selectable, Demand interval: 5 to 30 min, Individual harmonics upto 15th order for voltage and current, Percentage Unbalance – Voltage and Current, Cumulative Run Hours, Sampling rate of 64 samples / cycle, Measuring circuit burden should be lesser than 0.2 VA, Aux burden < 5VA, Meter shall be suitable for CT secondary 1A /5A including CTs, site programmable CT & PT ratio, Meters shall have RS485 port with MODBUS RTU protocol, with IP 51 protection from front end preventing dust and moisture entry, meters shall be capable of integration with EMS Software<br>All opening parts of the panel shall be sealable. Panels shall be complete with Al bus bars, separate earth bus bar to be provided through out the length of the panel along with base chanel of suitable size, cable alleys as per requirement, complete, numbering, danger plate etc as required as per specifications and drawings. Current density for busbarsize shall be designed considering not more than 0.8 A/sq.mm for aluminium. The switchgear live parts shall be isolated with proper insulation material. All switchgears shall be with spreader links, operating knobs/handles, DIN rail provision for isolators with required cable alleys. The panel design shall be in accordance with IS & Kerala state norms. All panels shall be cable alleys and seperate bus bar compartments for easy terminations as per KSEI standards with proper clearances. <br>Incomer -<br>500A FP Isolator - 1 no<br>500A 433V, 36kA best conductivity extensible Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required. <br>RYB phase indicating LED lamps with control fuses and switches - 1 set.<br>Surge Protection Device Class B with HRC fuses for backup as per manufacturer standard, including copper cable connection between arrestor and fuses - 1 set<br>Outgoings<br>Multifunction meter as per IEC 62053-21, specified above including CTs and all accessories - 7 set<br>100A 25kA TP Thermal Magnetic Based MCCB - 5 nos<br>80A 25kA TP Thermal Magnetic Based MCCB - 1 no<br>63A 25kA TP Thermal Magnetic Based MCCB - 1 no<br>

od56942/2022_2023 : SSB 2<br>Fabrication, supply, erection, testing and commissioning of dust and vermin proof, floor / wall mounted, front operated MV panel board as per IS 8623, CPRI Certified, compartmentalised (minimum form 3b) complete with hinged and earthed front doors with name plate, danger notice board, heavy duty rubber gaskets, removable gland plates made out of 3mm thick sheet steel including all components as shown in the schematic drawing. All opening parts of the panel shall be sealable. These panel should include surge arrester Class B or Class B+C/ Class 1+2 as per IEC 61643 (IP 20) with remote indication for defective arresters, arrester Spark Gap type to connect between Neutral and Earth.complete with back up fuse for SPD protection as per manufacturer standard. Providing all connections and interconnections as required and providing all accessories as required for complete installation as instructed by engineer in charge/consultant and as shown in the schematic layout provided. All switchgears shall be with with spreader links and rotary handle. Providing all connections and interconnections as required and providing all accessories as required for complete installation as instructed by engineer in charge/consultant and as shown in the schematic layout provided. <br>Necessary electrical and mechanical interlocking arrangements shall be provided as per scehmatic drawing to achieve operational functionality<br>All panels shall be with separate channels isolated from LT cable chambers for running of RS485 & other ELV cables for integration with EMS & IBMS. Switchgears and meters shall be with necessary communication ports for integration with BMS & EMS and Potential free contacts for BMS. All panel meters should be with RS485 ports for EMS integration. <br>All Multifunction meter shall be as per IEC 62053-21, class 1, having multiline LED display with following parameters -Phase wise instantaneous and Average values – Voltage, Current, Power Factor, Phase wise instantaneous and Average values – Active Power, Reactive Power lead & lag, Apparent Power, Import & Export Cumulative values– Active Energy, Reactive Energy lead & lag, Apparent Energy, 4. PF for 3 phases and average,Instantaneous Frequency,Total Harmonics Distortion – Phase wise Voltage and Phase wise Current, Min and max of VLL, VLN, A, F, W, VA, VAr, PF with date and time stamp,Battery backed RTC with 2 years of power down time, Demand calculations based on W, VA, VAr, 10. Demand sync – Sliding window or block window site selectable, Demand interval: 5 to 30 min, Individual harmonics upto 15th order for voltage and current, Percentage Unbalance – Voltage and Current, Cumulative Run Hours, Sampling rate of 64 samples / cycle, Measuring circuit burden should be lesser than 0.2 VA, Aux burden < 5VA, Meter shall be suitable for CT secondary 1A /5A including CTs, site programmable CT & PT ratio, Meters shall have RS485 port with MODBUS RTU protocol, with IP 51 protection from front end preventing dust and moisture entry, meters shall be capable of integration with EMS Software<br>All opening parts of the panel shall be sealable. Panels shall be complete with Al bus bars, separate earth bus bar to be provided through out the length of the panel along with base chanel of suitable size, cable alleys as per requirement, complete, numbering, danger plate etc as required as per specifications and drawings. Current density for busbarsize shall be designed considering not more than 0.8 A/sq.mm for aluminium. The switchgear live parts shall be isolated with proper insulation material. All switchgears shall be with spreader links, operating knobs/handles, DIN rail provision for isolators with required cable alleys. The panel design shall be in accordance with IS & Kerala state norms. All panels shall be cable alleys and seperate bus bar compartments for easy terminations as per KSEI standards with proper clearances. <br>Incomer -<br>315A FP Isolator - 1 no<br>315A 433V, 36kA best conductivity extensible Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required. <br>RYB phase indicating LED lamps with control fuses and switches - 1 set.<br>Surge Protection Device Class B with HRC fuses for backup as per manufacturer standard, including copper cable connection between arrestor and fuses - 1 set<br>Outgoings<br>Multifunction meter as per IEC 62053-21, specified above including CTs and all accessories - 5 set<br>160A 25kA TP Thermal Magnetic Based MCCB - 1 no<br>100A 25kA TP Thermal Magnetic Based MCCB - 3 nos<br>63A 25kA TP Thermal Magnetic Based MCCB - 1 no<br>

od62948/2022_2023 : DUMBWAITER PANEL<br>Incomer -<br>63A FP Modular Isolator - 1 no<br>63A 433V, 16kA best conductivity extensible Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required. <br>RYB phase indicating LED lamps with control fuses and switches - 1 set.<br>Surge Protection Device Class B+C/ Class 1+2 with HRC fuses for backup as per manufacturer standard, including copper cable connection between arrestor and fuses - 1 set<br>Outgoings<br>32A 100mA FP RCBO - 2 nos<br>25A 30mA DP RCBO - 1 no<br>25A best conductivity extensible Al SPN bus bar<br>6A SP MCB - 4 nos<br>

od62956/2022_2023 : AC PANEL 1<br>Incomer -<br>200A FP Isolator - 1 no<br>200A 433V, 25kA best conductivity extensible Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required. <br>RYB phase indicating LED lamps with control fuses and switches - 1 set.<br>Surge Protection Device Class B+C/ Class 1+2 with HRC fuses for backup as per manufacturer standard, including copper cable connection between arrestor and fuses - 1 set<br>Outgoings<br>63A 16kA TP Thermal Magnetic Based MCCB - 4 nos<br>32A 16kA TP Thermal Magnetic Based MCCB - 2 nos<br>25A 16kA TP Thermal Magnetic Based MCCB - 4 nos<br>

MV CABLE SUPPLY

od59017/2022_2023 : Supply of the following size 1.1kV grade XLPE insulated PVC sheathed, armoured Aluminium conductor power cable confirming to IS 7098 (part 1) ammended upto date. <br><br>3.5cx400sq.mm Al Cable<br><br><br>

od59143/2022_2023 : Supply of the following size 1.1kV grade XLPE insulated PVC sheathed, armoured Aluminium conductor power cable confirming to IS 7098 (part 1) ammended upto date. <br>4cx400sq.mm Al Cable<br>

od59292/2022_2023 : Supply of the following size 1.1kV grade XLPE insulated PVC sheathed, armoured Aluminium conductor power cable confirming to IS 7098 (part 1) ammended upto date. <br><br>3.5cx300sq.mm Al Cable<br>

od59293/2022_2023 : Supply of the following size 1.1kV grade XLPE insulated PVC sheathed, armoured Aluminium conductor power cable confirming to IS 7098 (part 1) ammended upto date. <br><br>3.5cx240sq.mm Al Cable<br>

od59294/2022_2023 : Supply of the following size 1.1kV grade XLPE insulated PVC sheathed, armoured Aluminium conductor power cable confirming to IS 7098 (part 1) ammended upto date. <br><br>3.5cx185sq.mm Al Cable<br>

od59308/2022_2023 : Supply of the following size 1.1kV grade XLPE insulated PVC sheathed, armoured Aluminium conductor power cable confirming to IS 7098 (part 1) ammended upto date. <br><br>3.5cx70sq.mm Al Cable<br>

od59311/2022_2023 : Supply of the following size 1.1kV grade XLPE insulated PVC sheathed, armoured Aluminium conductor power cable confirming to IS 7098 (part 1) ammended upto date. <br>3.5cx95sq.mm Al Cable<br>

od59331/2022_2023 : Supply of the following size 1.1kV grade XLPE insulated PVC sheathed, armoured Aluminium conductor power cable confirming to IS 7098 (part 1) ammended upto date. <br><br>3.5cx50sq.mm Al Cable<br>

od59373/2022_2023 : Supply of the following size 1.1kV grade XLPE insulated PVC sheathed, armoured Aluminium conductor power cable confirming to IS 7098 (part 1) ammended upto date. <br><br>3.5cx35sq.mm Al Cable<br>

od65513/2022_2023 : Supply of the following size 1.1kV grade XLPE insulated PVC sheathed, armoured Aluminium conductor power cable confirming to IS 7098 (part 1) ammended upto date. <br><br>4cx25sq.mm Al Cable<br>

od65517/2022_2023 : Supply of the following size 1.1kV grade XLPE insulated PVC sheathed, armoured Aluminium conductor power cable confirming to IS 7098 (part 1) ammended upto date. <br><br>4cx16sq.mm Al Cable<br><br>

od65524/2022_2023 : Supply of the following size 1.1kV grade XLPE insulated PVC sheathed, armoured Aluminium conductor power cable confirming to IS 7098 (part 1) ammended upto date. <br><br>4cx10sq.mm Al Cable<br>

od65527/2022_2023 : Supply of the following size 1.1kV grade XLPE insulated PVC sheathed, armoured Aluminium conductor power cable confirming to IS 7098 (part 1) ammended upto date. <br><br>4x6sq.mm Al Cable<br>

od65528/2022_2023 : Supply of the following size 1.1kV grade XLPE insulated PVC sheathed, armoured Aluminium conductor power cable confirming to IS 7098 (part 1) ammended upto date. <br>2cx6sq.mm Al Cable<br>

od65537/2022_2023 : Supply and laying, including providing terminations for following PVC sheathed, unarmoured flexible copper conductor cable confirming to IS 7098 (part 1) ammended upto date for providing dedicated earthing. <br><br>1Cx50sq.mm Copper Flexible Cable (2XY) <br>

od67954/2022_2023 : Supply of the following size 1.1kV grade XLPE insulated PVC sheathed, armoured Aluminium conductor power cable confirming to IS 7098 (part 1) ammended upto date. <br>12cx2.5sq.mm Cu Control Cable (2XFY)<br>

od67975/2022_2023 : Supply of the following size 1.1kV grade XLPE insulated PVC sheathed, armoured Aluminium conductor power cable confirming to IS 7098 (part 1) ammended upto date. <br>2cx2.5sq.mm Cu Control Cable (2XFY)<br>

MV CABLE LAYING

7.1.1 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.Upto 35 sq. mm

7.5.1 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.Upto 35 sq. mm

7.5.2 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.Above 35 sq. mm and upto 95 sq. mm

7.5.3 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.Above 95 sq. mm and upto 185 sq. mm

7.5.4 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.Above 185 sq. mm and upto 400 sq. mm

7.7.1 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.Upto 35 sq. mm (clamped with 1mm thick saddle)

7.7.2 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

7.7.3 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)

7.7.4 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

7.8.1 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.Upto 35 sq. mm (clamped with 1mm thick saddle)

7.8.2 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

7.8.3 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)

7.8.4 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

7.10 : Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required.

MV CABLE END TERMINATION