Vegetable And Fruit Promotion Council Keralam Tender

5.22A 6.aReinforcement for RCC work bent tied and placed in position using torsteel including cost and conveyance of all materials labour charges etc. completeThermo-Mechanically Treated bars of grade Fe-500 D or more.

5.1.3. 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

50.2.25.1.Filling with contractor's own earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-in-charge.

4.1.8. 1:4:8 (1 Cement : 4 coarse sand(zone-III) : 8 graded stone aggregate 40 mm nominal size).

50.6.2. 2. Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x15cm or nearest available size confirming to IS 2185 part I of 1979 for super structure above plinth level up to floor five level with thickness 15cm in: CM 1:6 (1 cement : 6 coarse sand) etc complete

13.1.1. Plastering with cement mortar 1:4, 12mm thick one coat floated hard and trowelled smooth including cost and conveyance of all materials, labour charges etc. complete for walls.

13.43.1. Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer.

13.44.1. Finishing walls with water proofing cement paint of required shade : New work (Two or more coats applied @ 3.84 kg/10 sqm).

50.10.1 . Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc. ) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

12.50. Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm ( + 0.05 %), total coated thickness with zinc coating 120 gm per sqm as per IS:277 in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

9.48.1.Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc.

17.7.1. Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

17.7.3. Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Flat back wash basin size 550x400 mm with single 15 mm C.P. brass pillar tap.

50.17.1.4. Supplying and fixing CP Health Faucet good quality including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

50.18.9.7.1. Providing and fixing PVC pipes including jointing of pipes with one step PVC solvent cement ,trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 63 mm dia 6 Kgf/cm2

50.18.9.9.1. Providing and fixing PVC pipes including jointing of pipes with one step PVC solvent cement ,trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 110 mm dia 6 Kgf/cm2

50.18.9.20.6.Providing and fixing PVC moulded fittings / accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 x 63 x 63 mm dia Door Tee

50.18.9.20.7. Providing and fixing PVC moulded fittings / accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia Vent cowl

50.18.9.20.4. Providing and fixing PVC moulded fittings / accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia Bend

50.18.9.22.5. Providing and fixing PVC moulded fittings / accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 x 110 x 110 mm dia Tee

50.18.9.22.4. Providing and fixing PVC moulded fittings / accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia Bend

50.18.9.22.8. Providing and fixing PVC moulded fittings / accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia Vent cowl

50.18.9.13.2. Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 25mm dia 12gf/cm2- External work - Exposed on wall

50.18.9.12.2. Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 20mm dia 12Kgf/cm2- External work - Exposed on wall

18.48. Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

18.17.1. Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25mm bore

18.15.2. Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931: 20 mm nominal bore.

50.12.4.1. Providing and fixing false ceiling with 7.5mm thick PVC plain panel board ceiling of approved quality in aluminium frame work with necessary screws etc complete

11.37. Providing and laying Ceramic glazed floor tiles of size 300x300 mm(thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc.,., complete.

21.1.1.2. Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : Powder coated aluminium (minimum thickness of powder coating 50 micron) Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side.With float glass panes of 4.0 mm thickness

OD Supplying and fixing 200mm dia PVC rain water gutter C type section including fitting with 32mx5m MS flat supporters at 1m interval etc. complete

Providing and fixing ss type floor trap including fitting and labour charge

OD 35 mm thick factory made Solid panel PVC Door shutter and frame made out of single piece extruded solid PVC profiles, 5 mm (± 0.2mm) thick, having styles &rails (except lock rail) of size 95 mm x 35 mm x 5 mm, out of which 75 mm shall be flat and 20 mm shall be tapered (on both side), having one side thickness of 15 mm integrally extruded on the hinge side of the profile for better screw holding power, including reinforcing with MS tube of size 40 mm X 20 mm x 1 mm, joints of styles & rails to be mitered cut & joint with the help of PVC solvent cement, self driven self tapping screws & M.S. rectangular pipes bracket of size 190 mm X 100 mm of cross section size 35 mm x 17 mm x 1 mm at each corner.

Supplying and fixing electrical works including 4 nos tube, 2 nos wall mounted fan. 2 nos led bulb 3 nos 5 amp switch, 2 nos 16 amp switch including wiring cable switch boar, labour and transportation charge. As per the direction in engineer in charge