The Metal Industries Limited Tender
Everything can be found here in your one-stop destination for all types of Kerala tenders online - be it Kerala PWD tenders or an LSGD Kerala tender. Search from across the categories, cities, and authorities while having the option to download tender-related documents. Also, get to know how to register as a bidder and how to bid online for Kerala tenders.
Costs
EMD
₹ 1,30,000Document Cost
₹ 5,900Tender Fee
Refer Documents
Summary
Standardisation And Augmentation Of Electrical Installation
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2021_MIL_454039_1Tender No
MIL/Elec/01/2021Tender Authority
The Metal Industries Limited ViewPurchaser Address
-Website
http://http://themetalindustries.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
Preferred Make of Material
Articles of Agreement
Safety Conditions
BOQ Items
25A Single Pole MCCB with spreader set as out going to LDB UPS
2
-
3958
25A Double MCCB with spreader set To Single phase LDB
1
-
3958
32-63A Triple MCCB with spreader set to Essential water pump
2
-
3958
32-63A Four pole MCCB with spreader set to TPN LDB , Security light, Canteen and spare
5
-
3958
Supplying and fixing following way, Single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator), 12 way double door
1
-
2053
16 way, Double door
1
-
2453
Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator), 4 way (4+24), Double Door
1
-
3068
8 way (4 + 24), Double door
1
-
4601
Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as required . (Note : Vertical type MCB TP DB is normally used where 3 phase outlets are required.) 8 way (4 + 24), Double door
1
-
7744
12 way (4 + 36), Double door
1
-
9828
Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single Pole
78
-
199
Single pole and neutral
4
-
544
Double pole
4
-
556
Triple pole
20
-
826
Triple pole and neutral
4
-
1092
Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A
2
-
339
63A
2
-
385
Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40A
2
-
832
63A
1
-
839
100A
1
-
1047
Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 25A
4
-
1927
Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 25A
2
-
2526
40A
2
-
2626
63A
4
-
2777
Supply and Installaing on Truss Bay Light Fitting LED Circular 180 Watts 150 lm/W UV Stabilized IP PC Lens, 140 -270 V AC input range 4kV inbuild Suge protection 50k Burning Hrs @ L70 B50 standerds 340mm Dia THD 10% 5700K Colour Temp (CCT) 60 Degree lense IP 66 and IK 07 capatable Panasonic Make ENVISO PRO PBYM14KL8 or equilent.
28
-
12470
Supply and Installaing on Truss WELL GLASS LED Fitting 70 Watts 130 lm/W 140 -270 V AC input range 6kV inbuild Suge protection 50k Burning Hrs @ L70 B50 standerds 340mm Dia THD 10% 5700K Colour Temp (CCT) 60 Degree lense IP 66 and IK 08 capatable Panasonic Make MERLIN PLUS PWG09708 or equilent.
12
-
4698
Industrial Batten IP 65 LED Batten with inbuilt heat sink, polycarbonate housing equipped with anti-glare diffuser & energy efficient electronices driver 40 W 6500 K (CCT) Panasonic Make TRUSS Model No PBTM05407 or equilent.
20
-
2586
Industrial Batten IP 20 LED batten for surface and suspended application. White powder coated CRCA housing with LEDs. Seamless front frame is with white high transmission acrylic cover and decorative end cap. 20 W 5700 K (CCT) Panasonic Make HARROW Model No PBTM12208 or equilent.
12
-
1450
Track light with aluminum profile 100 LED per meter 10 W/ Mts 12/24 V DC light back up with 24Ah 12V lithium-ion battery and BMS system
100
-
487
Part 2 Industrial Power Wiring Bus Trunking system. Supplying, installing on wall or suspension on ceiling, testing and commissioning of following capacity Air Insulated Compact Type Bus Trunking for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply with metal clad enclosure having IP-54 rating after fixing the tap off boxes and all accessories, made of 1.6mm thick steel sheet duly powder coated in convenient sections complete with 4 Nos aluminium bus bars having current density of 130 A/ sq cm at nominal current rating, necessary joints, elbow joints & expansion joints, Horizontal and vertical run continuous earthing with 2 Nos aluminium strip of suitable size (one on each side) including, G.I. clamping brackets, suspenders, angle iron bracket, steel fasteners, connecting to earthing system etc. as required. 400A Isc = 30kA for 1 second
75
-
8915
Supplying, installation, testing & commissioning of following capacity End Feed Unit for the existing Air Insulated Compact Type bus Trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick steel sheet enclosure (IP54) duly powder coated with provision of MCCB/ACB (but without MCCB/ACB) complete with necessary joints including clamping brackets, angle iron bracket, steel fasteners, connecting to earthing system etc. as required. MCCB 4 pole 200 A 15kA SC for 1 sec for 75kW Electric Furnace
1
-
5513
MCCB 4 pole 125A 15kA SC for 1 sec for 50kW Electric Furnace
3
-
4987
Supplying, installation, testing & commissioning of following capacity Plug In/ tap off box on the existing Air Insulated Compact Type bus Trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply including 4 Nos LED indicator and control fuse made with 1.6mm thick sheet steel enclosure (IP54) duly powder coated with provision of MCCB/ACB (but without MCCB/ACB) complete etc. as required. MCCB 4 pole 200 A 15kA SC for 1 sec For 50 HP Inductive Load feeder.
1
-
6358
MCCB 4 pole 63 to 125 A 15kA SC for 1 sec Up to 35HP Inductive Load feeders
9
-
5548
Part 3 Closed Perforated Cable Tray Hot dipped GI Supplying and installing following size of perforated painted with powder coating M.S. cable trays (with cover) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 100mm widthX 50mm depth X 1.6mm thickness
100
-
476
150 mm width X 50 mm depth X 1.6 mm thickness
50
-
531
200 mm width X 50 mm depth X 1.6 mm thickness
25
-
597
300 mm width X 50 mm depth X 1.6 mm thickness
15
-
621
375 mm width X 50 mm depth X 2.0 mm thickness
20
-
660
450 mm width X 50 mm depth X 2.0 mm thickness Metre
10
-
700
Supplying and installing following size of perforated painted with powder coating M.S. cable trays bends (with Cover) with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 100 mm width X 50 mm depth X 1.6 mm thickness
24
-
808
150 mm width X 50 mm depth X 1.6 mm thickness
20
-
947
200 mm width X 50 mm depth X 1.6 mm thickness
10
-
1143
300 mm width X 50 mm depth X 1.6 mm thickness
6
-
1340
375 mm width X 50 mm depth X 2.0 mm thickness
5
-
1827
450 mm width X 50 mm depth X 2.0 mm thickness
4
-
2089
Supplying and installing following size of perforated painted with powder coating M.S. cable trays Tee (with Cover) with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 100 mm width X 50 mm depth X 1.6 mm thickness
7
-
909
150 mm width X 50 mm depth X 1.6 mm thickness
2
-
1072
225 mm width X 50 mm depth X 1.6 mm thickness
6
-
1310
300 mm width X 50 mm depth X 1.6 mm thickness
3
-
1549
375 mm width X 50 mm depth X 2.0 mm thickness
1
-
2118
450 mm width X 50 mm depth X 2.0 mm thickness
4
-
2431
Supplying and installing following size of perforated painted with powder coating M.S. cable trays Cross Member (with Cover) with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 100 mm width X 50 mm depth X 1.6 mm thickness
6
-
909
150 mm width X 50 mm depth X 1.6 mm thickness
4
-
1072
225 mm width X 50 mm depth X 1.6 mm thickness
4
-
1310
300 mm width X 50 mm depth X 1.6 mm thickness
2
-
1549
375 mm width X 50 mm depth X 2.0 mm thickness
2
-
2118
450 mm width X 50 mm depth X 2.0 mm thickness
1
-
2431
Supplying and installing following size of perforated painted with powder coating M.S. cable trays Reducer (with Cover) with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 100 mm width X 50 mm depth X 1.6 mm thickness
6
-
880
150 mm width X 50 mm depth X 1.6 mm thickness
6
-
1023
225 mm width X 50 mm depth X 1.6 mm thickness
4
-
1268
300 mm width X 50 mm depth X 1.6 mm thickness
6
-
1505
375 mm width X 50 mm depth X 2.0 mm thickness
2
-
1858
450 mm width X 50 mm depth X 2.0 mm thickness
4
-
2144
Part 4 Cable and End Termination Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface /Through existing cable tray as required. Up to 8 Mts height. Up to 35 sq. mm (clamped with 1mm thick saddle)
840
-
39
Above 35 sq. mm and up to 95 sq. mm (clamped with 25x3mm MS flat clamp)
370
-
104
Above 95 sq. mm and up to 185 sq. mm (clamped with 25/40x3mm MS flat clamp)
200
-
122
Above 185 sq. mm and up to 400 sq. mm (clamped with 40x3mm MS flat clamp)
100
-
182
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation and refilling the trench etc as required, but excluding sand cushioning and protective covering. Up to 35 sq. mm
120
-
167
Above 35 sq. mm and up to 95 sq. mm
25
-
181
Above 95 sq. mm and up to 185 sq. mm
50
-
196
Above 185 sq. mm and up to 400 sq. mm
80
-
239
Supplying and making end termination with Double compression whether proof Cable gland and Heavy duty aluminium lugs and Earth Tag of suitable size for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. Up to and including 19mm Size Double compression Gland size
60
-
326
Up to and Including 32 mm size Double compression Gland size
20
-
726
Up to and Including 40mm size Double compression Gland size
16
-
1049
Up to and Including 50 mm size Double compression Gland size
20
-
1270
Above 63 mm size Double compression Gland size
14
-
2893
Supply at site Power Cables, Solid Aluminium conductor up to 10 sqmm balance stranded conductor, XLPE Insulated,cores laid up, PVC tape inner sheathed, unarmoured/Armour(Aluminium wire for single core up to 70 sqmm balance Aluminium strip, Galvanised wire for cables up to 2x16 sqmm, 3x10 sqmm,4x10 sqmm balance all galvanised steel strip), extruded PVC Type ST2 sheathed,650/1100V grade as per IS 7098(Part 1) 1988 4 core 6 sq mm armoured aluminium
80
-
100
4 core 10 sq mm armoured aluminium
50
-
119
4 core 16 sq mm armoured aluminium
25
-
140
4 core 25 sq mm armoured aluminium
100
-
188
3.5core 35 sq mm armoured aluminium
140
-
240
3.5core 50 sq mm armoured aluminium
20
-
282
3.5core 95 sq mm armoured aluminium
40
-
477
3.5core 150 sq mm armoured aluminium
10
-
690
3.5core 240 sq mm armoured aluminium
30
-
1113
3.5core 400 sq mm armoured aluminium
154
-
1715
Supply at site Power and Control Copper Cables, Solid Copper conductor,XLPE Insulated,cores laid up, PVC tape innersheathed,Unarmoured/Armour (Galvanised wire for cables up to 14 x 1.5 sqmm, 9x2.5 sqmm,2x16 sqmm, 3x10 sqmm,4x10 sqmm balance all galvanised steel strip),extruded PVC Type ST2 Sheathed, 650/1100 V grade as per IS 7098 (Part 1) 1988 1.5 sq mm 2 core armoured copper control cable
25
-
78
1.5 sq mm 3 core armoured copper control cable
25
-
98
1.5 sq mm 4 core armoured copper control cable
25
-
120
1.5 sq mm 6 core armoured copper control cable
40
-
163
2.5 sq mm 2 core armoured copper control cable
20
-
109
2.5 sq mm 3 core armoured copper control and Light cable
300
-
135
2.5 sq mm 4 core armoured copper control and Light cable
400
-
169
2.5 sq mm 5 core armoured copper Power cable
120
-
203
2.5 sq mm 10 core armoured copper control cable
10
-
356
4 sq mm 5 core Un armoured copper Power cable
25
-
254
6 sq mm 4 core Un armoured copper Power cable
12
-
308
6 sq mm 5 core Un armoured copper Power cable
12
-
365
10 sq mm 4 core Un armoured copper Power cable
16
-
480
10 sq mm 5 core Un armoured copper Power cable
15
-
564
16 sq mm 4 core Un armoured copper Power cable
25
-
732
16 sq mm 5 core Un armoured copper Power cable
25
-
818
25 sq mm 4 core Un armoured copper Power cable
10
-
1370
Supplying and making cable route marker with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) of size 60 cm X 60 cm at the bottom and 50 cm X 50 cm at the top with a thickness of 10cm including inscription duly engraved as required.
24
-
530
Supply and Providing FRP walk ways up to 24Mts height truss purling of existing space frame Industrial shed construction. All light cables fittings and Bus Trunking shall be accessible from the walk way the width of the wake way shall be 45 cms with 2 side Z purling using Hot dipped GI Z sections having minimum 2 mm thickness to accommodate 2 labours working capacity.
158
-
954
Supply and providing FRP Transformer yard fencing using 40 x 40 mm FRP pillars in every 1.5 mts span FRP grills at a height of 1.8 Mts including 2 Nos SS hinged doors with lockable mechanism on top of 60 cms Solid concrete block curb wall as directed by the Engineer in charge
70
-
1478
Supply and providing wall supporting type fixed FRP ladders to access the walk way from plant
40
-
987
Supply of suitable size Polyamide flexible conduit with IP67 End coupling fixed using Polyamide Bracket having 105 Degree Celsius Temperature as per UL 94V0
500
-
110
Part 5 Change over Panel, MSB SSB and Motor control canters, State enclosure, Out door kiosk factory built assemblies as per Annexure enclosed. Fabrication, supply, conveyance, installation testing and commissioning of floor or wall mounting, dust and vermin proof, cubicle type MV panel board comprising of the following components/ devices & complying to IS 8623 Fabrication of fully partitioned, dust and vermin proof enclosure for panel assembly as per form 4 of IS 8623 (with latest amendments) using CRCA sheet as per approved design and requirement, with front and rear access facility, bus bar chambers, hinged doors for all switch gear compartments, earthing the doors using 4 sq mm braided copper conductor, providing necessary lifting hooks, cut-outs for mounting meters, relays, indication lamps, bus bar interconnection etc, detachable covers for bus bar chamber and cable alley, powder coating the assembly after subjecting to 7 tank process etc as required. CRCA sheet alone be used for the fabrication. Angles/ flats/ slotted angles etc shall not be used for the fabrication of panel assembly. The measurements will be taken the area of the complete sheets used for panel board including partitions, folding, shrouding etc. Supply and fabrication of MV panel board using 1.6mm CRCA sheet, powder coated (excluding base frame)
92
-
2394.39
Supply and providing Aluminium Bus bar having main bus with 0.6 A/ Sqmm and inter connection with 0.8 A/sqmm. Supported by L type/ Step type/ finger type 600 V Rated DMC. Anodized aluminium bus bar shall be insulated using heat shrinkable colour sleeve. Only 6 mm thick sections shall be used as bus bar with multiple run as required.
68
-
354
Supply and providing 4mm SMC sheet as shrouding for bus interconnection / terminations etc. including required nut & bolt etc.
4.6
-
3982
Supply and providing heavy duty 'A' section Neoprene gasket in the panel suitable for 1.60/ 2.00 mm sheet (Samples shall be heat aged at 100 deg. C. for 70 hours and tested as per ASTM D-573. Changes in properties shall not exceed the following limits: Tensile Strength : 30% Ultimate Elongation : 50% (max.) Durometer Hardness : 15 points)
20
-
548
Supply and providing copper bus bars duly tinned at all joints including finger type/Conical/ Strip hold SMC bus bar supports in the bus chamber, suitable size nut & bolt, providing Green striped Yellow heat shrink sleeves etc. as required. Density of EC grade copper shall be calculated for measurement will be considered @ 8.96g/cc. Copper only will be weighed for measurement.
20
-
1150
Supply and providing suitable sized SS 202/GI/ Brass bolt nut washers hardware as required.
40
-
240
Supply Fabricate and erect 35 x 35x 6 mm ISLA Wall frame with 8 mm tapped/ Client rivet hole to accommodate SMDB/MCBDB/VDB/ MCC/PBS/ Starter Panel panels and 6 nose 16mm holes to mound the panel to ground as required duly painted using anti rust rubber based black paint. Over 2 coat of zincromate base coat or using epoxy anty rust coating on base frame.
75
-
145
Supply Fabricate and erect 100 x 50 mm ISMC Base frame with 8 mm tapped/ Client rivet hole to accommodate panels and 6 nose 16mm holes to mound the panel to ground as required duly painted using anti rust rubber based black paint. Over 2 coat of zincromate base coat or using epoxy anty rust coating on base frame.
155
-
135
Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure 8 Way 4 Pole MCCB Incommer and 4 Pole MCCB Out Going Double Door Load bank ( Power Safe Panel) suitable for 100A MCCB as incomer Panel including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing 4P 100 A 18kA MCCB with suitable spreaders as incomer and 16A/20A/32A/40A/50A/ 63A 4 Pole (FP) MCCB as outgoing. with suitable spreaders Meter Module with digital multi function meter (V, A, F, KWHr), 100/5 Class 1 resin cast CT's 3 Nos LED Indicators, control MCBs and corner box on both side at the top, Add on module of the same size of the panel at the bottom and 2 nose of cable alleys in both sides complete. fixed on wall / MS Frame work using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required 8 way double cover(( L & T make Enersys / Havells Load line or equivalent ready made sub board) for Inductive load up to 15 Hp.
2
-
81701.43
200A 4 pole 18kA MCCB with spreader set as Incommer
2
-
6520
32-63A Triple 15kA MCCB with spreader set to Power Load up to 10kW
3
-
3958
32-63A Four pole 15kA MCCB with spreader set 10-15kW Power Load
10
-
3958
Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure 8 Way TP Motor Control Centre (MCC1) Provision to install 80 A TP MCCB as Incommer and 3 Pole MPCB + Power Contactor with 2 NO 2 NC Out Going suitable for 100A MCCB as incomer Panel including copper /brass bus bar, neutral link, earth bus and DIN rail Suitable for fixing 1 HP 3 Phase MPCB ICU 100kA Rotary type with suitable spreaders as incomer and 80A TP Pole MCCB as outgoing with suitable spreaders Meter Module with digital multi function meter (V, A, F, KWHr), 100/5 Class 1 resin cast CT's 3 Nos LED Indicators, control MCBs and corner box on both side at the top. for Blower ,drilling macine circulating pump brench grinders and simillar up to 2 HP Eqiuments.
3
-
74615
80A TP 15kA MCCB with spreader set as Incommer Conforms to IS/IEC 60947-2,
IEC 60947-2 & EN 60947-2
2
-
1385
16A MOG-H1M Rotary Type Thermal Release range 1.6-2.5A ICU 100kA
24
-
2012
Auxiliary and Alarm left side mounding
24
-
500
DOL starter Link up to 13A
24
-
185
AC3 Rating 13 A Power contactor with 230 V coil voltage IS / IEC 60947-4-1 & IEC 60947-4-1
24
-
950
ON / OFF Push button station with illuminated push button on dia cast aluminium enclosure IP54
40
-
780
8 mm Metal body R/Y/B and G Led Indication lamp with in line glass control fuse
120
-
115
Part 6. Supply and Providing Electrical accessories for MV Panel boards :- Providing and fixing following rating and breaking capacity and pole MCCB with Micro processor release Conforms to IS/IEC 60947-2 including providing suitable spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 16 A-100A, 35/36 kA (Ics=100%Icu), 4 pole, current limiting type MCCB with microprocessor based release with overload setting of 50-100% having adjustable OL & SC.
2
-
11610
125 A, 35/36 kA (Ics=100%Icu), 4 pole, current limiting type MCCB with microprocessor based release with overload setting of 50-100% having adjustable OL & SC.
1
-
15093
630 A, 50/55 kA (Ics=100%Icu), 4 pole, current limiting type MCCB with microprocessor based release with overload setting of 50-100% having adjustable OL & SC.
2
-
27771
250 A, 50/55 kA (Ics=100%Icu), 4 pole, current limiting type MCCB with microprocessor based release with overload setting of 50-100% having adjustable OL & SC. Mechanical inter lock on rotary frond drive mechanism with 3 Lock 1 Key system.
1
-
35540
630 A, 50/55 kA (Ics=100%Icu), 4 pole, current limiting type MCCB with microprocessor based release with overload setting of 50-100% having adjustable OL & SC. Mechanical inter lock on rotary frond drive mechanism with 3 Lock 1 Key system.
2
-
43350
Providing and fixing following rating and breaking capacity and pole MCCB with Thermo magnetic release Conforms to IS/IEC 60947-2 and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 400 A, 35 KA,TPMCCB
2
-
21512
250 A, 35 KA,TPMCCB
1
-
11140
200 A, 25 KA,TPMCCB
4
-
10953
160 A, 16 KA,TPMCCB
1
-
4688
125 A, 16 KA,TPMCCB
4
-
4145
100 A, 16 KA,TPMCCB
5
-
3726
Under Voltage release For all voltage ranges up to 630A MCCB
5
-
1102
Rotary handle (including BUC handle with door inter-lock defeat and pad lock facility) Up to 250A extended type
21
-
1356
Part 7. Earthing and Miscellaneous works:- Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.0 metre long etc. (but without charcoal/ coke and salt ) as required.
10
-
5146
Providing and fixing 25 mm X 3 mm copper strip on surface or in recess for connections etc. as required.
40
-
1009
Providing and fixing 40 mm X 4 mm Nical Sealed Copper Bonded Earthing Strips 250 microns copper Bonded on surface or in recess for connections etc. as required.
150
-
575
Providing and fixing 50 mm X 6 mm G.I. strip on surface or in recess for connections etc. as required.
100
-
206
Supply and providing Heat shrinkble sleeves for 50 x 6 mm earth conductors Yellow Green sriped clour. Duly inserted in the exposed earth srips.
50
-
145
Supply and providing Heat shrinkble sleeves up to 40 x 4mm earth conductors Green clour. Duly inserted in the exposed earth srips.
100
-
110
Supply and Changing roof sheet for DG room 0.45 mm TATA/JSW colour coated Tripode sheet roof laying sheet usin self taped SS/Aluminum Aloy Hex head screws with rubber gasket as required.
70
-
650
Supply and providing wall clading and inner seperation using wall cladding sheet snwitched 0.35 x 035 with 12 mm PUF insulation TATA/JSW colour coated Tripode sheet roof laying sheet usin self taped SS/Aluminum Aloy Hex head screws with rubber gasket as required.
36
-
1350
Supply and laying Dlink/ RR/ Finolex cat 6 cable through existing polymade/DWC conduit
305
-
35
4 pair FR PVC sheathed copper conductor polyethylene polyester taped Telephone cables for indoor application (un - armoured) conforming to ITD specifications
300
-
19
Labaling using form sheet of 4 -6 mm thick duly flexo print in multy colour labels and instructions as per directions by Engineering incharge
32
-
180
Part 8. HT Yard work :- Supplying and erection of 11 KV pin insulator complete with large steel head G.I. pin, nuts, washers etc. as required
3
-
281
Supplying and erection of 11 KV disc insulator for 11 KV over head lines with galvanised insulator fittings, ball and socket type and complete with galvanised strain clamps, bolts, nuts, washers etc. as required.
6
-
931
Supply and replacing 11 KV Outdoor type Air Break switch shall confirming IS: 9920 / 1981 (part-I to IV), IS: 2633 & IS: 2544/1973 with latest amendment if any and as per drawing. Including necessary modification in the MS channel as required.
1
-
17500
Supplying and erection of three piece nonlinear resistor type lightning arrestor suitable for 3 wire, 11 KV overhead lines with rated voltage 9 KV (rms) with a nominal discharge current rating of 5 KA and complete with galvanised clamping arrangement, G.I. bolts, nuts, washers etc. as required.
3
-
2548
Excavation for foundation in soft soil including dressing of sides and ramming of bottoms, lift up to 1.5 m including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 metres.
30
-
330
Excavation for cable trenches of depth up to 1.2 m in soft soil including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50 metres.
60
-
333
Providing and laying in position cement concrete 1:3:6 (1 cement : 2 coarse sand : 6 graded stone aggregate 40 mm nominal size) in foundation of pump, DG set etc including form work etc as required
4
-
6614
Providing and laying in position reinforced cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) in foundation of pump, DG set etc including form work etc as required (excluding reinforcement).
2
-
8029
Providing brick work (in width 225 mm or more) with F.P.S. bricks of class designation 7.5 in cement mortar 1:4 (1 cement : 4 coarse sand) at all levels.
6
-
6362
Providing 15mm thick cement plaster of mix 1:4 (1 cement : 4 fine sand) at all levels.
40
-
306
Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required. 100 mm Dia
6
-
525
150 mm Dia
2
-
598
250 mm Dia
4
-
701
300 mm Dia
8
-
854
Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc, complete as required. 32 mm dia (OD-32 mm & ID-38 mm
200
-
116
63 mm dia (OD-63 mm & ID-51 mm
60
-
209
90 mm dia (OD-90 mm & ID-76 mm
90
-
249
120 mm dia (OD-120 mm & ID-103 mm
75
-
341
Supplying and fixing 30 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top along with 30 A "C" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.
8
-
3048
Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top along with 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.
6
-
1232
Supply of following starter units to replace damaged/ oil cooled starter panels 12.5 HP FASD State panel with out enclosure (Enclosure will be measured separately as per item No ---)but with base plate and control fuses. MN type AC 3 Duty coil voltage 415 V Relay 14-23, with illuminated push button station on aluminium dia cast pust button station housing with IP 67 mounted and wired on motor control gear box fabricated out of 16 gauge CRCA sheet steel duly powder coated with handed door and neoprene beading as directed by Engineer in charge.
2
-
10957
20 HP FASD State panel with out enclosure (Enclosure will be measured separately as per item No ---)but with base plate and control fuses. MN type AC 3 Duty coil voltage 415 V Relay 14-23, with illuminated push button station on aluminium dia cast pust button station housing with IP 67 mounted and wired on motor control gear box fabricated out of 16 gauge CRCA sheet steel duly powder coated with handed door and neoprene beading as directed by Engineer in charge.
2
-
11145
30 HP FASD State panel with out enclosure (Enclosure will be measured separately as per item No ---)but with base plate and control fuses. MN type AC 3 Duty coil voltage 415 V Relay 14-23, with illuminated push button station on aluminium dia cast pust button station housing with IP 67 mounted and wired on motor control gear box fabricated out of 16 gauge CRCA sheet steel duly powder coated with handed door and neoprene beading as directed by Engineer in charge.
3
-
12465
Supplying and erection of a set of cross bracing Flame work for 11 KV over head line double pole structure having four members fabricated out of 50 mm X 50 mm X 6 mm angle iron to form a rectangle of minimum size 1400 mm width X 2500 mm height, complete with 50 mm X 6mm M.S. flat iron clamps, bolts and nuts including drilling holes for insulator pins, bolts and nuts etc (as per drawing) and painting with primer and finish paint as required. Set 5677
2
-
5677
Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel, at least 2 mm thick, and vitreous enamelled white on both sides, and with inscription in single red colour on front side as required.
6
-
244
2mm Electrical garage rubber mat
8
-
1819
A3 Drawing for scheme to Electrical inspectorate as fitted
24
-
600
Smart demand controller with class 0.5 CT's and communication protocol Socomec Make Model Diris A30 2 in /Out Module or similar functions in Schnider/L&T /Risheb Make. With alaram nd staatus indication disply
1
-
48000
Supply and providing Multy function meters with Power and Energy paramenters with suitable CT's energy mnagement Feeder wise with communicaion port
9
-
6500
Supply of service contracting staff during the execution along with this contrct Dismanling/ Alteernation/Modificaation/Reconnection works as well as temprory connection to hindeance free reular shift operation. It has to ensure safe operational envoinment at plant during the entair period of contract. The contrct staaff expected to take instructions from engineer incharge and perform labour works. Electrician
30
-
750
Welder
30
-
750
Fitter
45
-
750
Line man assistant
45
-
675
Charges for preparing drawing of the complete Electrical installation after completion of the present work and preparing completion report with Electrical Inspectorate Department and avail KSEB service connection application form and submitting to the consumer for up grading HT Contract demand up to 260kVA Three phase service connection/Load regularization and Additional CD etc (Actual amount paid on production of Original bill/ Invoice or demand letter from KSEB department)
1
-
8000
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements